Bad page threshold value should be valid in the range between
-1 and max records length of eeprom. It could determine when
saved bad pages exceed threshold value, and proceed corresponding
actions.

v2: When using the default typical value, it should be min
value between typical value and eeprom max records length.

v3: drop the case of setting bad_page_cnt_threshold to be
    0xFFFFFFFF, as it confuses user.

Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

bad_page_threshold could be configured to enable/disable the
associated bad page retirement feature in RAS.

When it's -1, ras will use typical bad page failure value to
handle bad page retirement.

When it's 0, disable bad page retirement, and no bad page
will be recorded and saved.

For other valid value, driver will use this manual value
as the threshold value of totoal bad pages.

v2: correct documentation of this parameter.

v3: remove confused statement in documentation.

Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Event bitmask is a 64-bit mask with only 1 bit set. Sending this
event bitmask in KFD SMI event message is both wasteful of memory
and potentially limiting to only 64 events. Instead send event
index in SMI event message.
Please note this change does not break the ABI for the two event
types defined so far. The new index is identical to the mask used
before.

Signed-off-by: Mukul Joshi <mukul.joshi@amd.com>
Suggested-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This regressed some working configurations so revert it.  Will
fix this properly for 5.9 and backport then.

This reverts commit 38e0c89a

.

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Enable GFXOFF for navy_flounder.

Signed-off-by: Jiansong Chen <Jiansong.Chen@amd.com>
Reviewed-by: Likun Gao <Likun.Gao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

1. For Navi12, CHIP_SIENNA_CICHLID, skip tmr load operation;
2. Check pointer before release firmware.

v2: use CHIP_SIENNA_CICHLID instead
v3: remove local "bool ret"; fix grammer issue
v4: use my name instead of "root"
v5: fix grammer issue and indent issue

Signed-off-by: Liu ChengZhe <ChengZhe.Liu@amd.com>
Reviewed-by: Luben Tuikov <luben.tuikov@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Assigning false to block->status.hw overwrites PSP's previous
hardware status, which causes the PSP to Resume operation after
hardware init.

Remove this assignment and let the PSP execute Resume operation
when it is told to.

v2: Remove the braces.
v3: Modify the description.

Signed-off-by: Liu ChengZhe <ChengZhe.Liu@amd.com>
Reviewed-by: Luben Tuikov <luben.tuikov@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Trying to grab dma_resv_lock while in commit_tail before we've done
all the code that leads to the eventual signalling of the vblank event
(which can be a dma_fence) is deadlock-y. Don't do that.

Here the solution is easy because just grabbing locks to read
something races anyway. We don't need to bother, READ_ONCE is
equivalent. And avoids the locking issue.

v2: Also take into account tmz_surface boolean, plus just delete the
old code.

Cc: linux-media@vger.kernel.org
Cc: linaro-mm-sig@lists.linaro.org
Cc: linux-rdma@vger.kernel.org
Cc: amd-gfx@lists.freedesktop.org
Cc: intel-gfx@lists.freedesktop.org
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Christian König <christian.koenig@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Remove casting the values returned by memory allocation function.

Coccinelle emits WARNING:

./drivers/gpu/drm/amd/powerplay/hwmgr/vega20_processpptables.c:893:37-46: WARNING: casting value returned by memory allocation function to (PPTable_t *) is useless.

Signed-off-by: Li Heng <liheng40@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Compiler leaves a 4-byte hole near the end of `dev_info`, causing
amdgpu_info_ioctl() to copy uninitialized kernel stack memory to userspace
when `size` is greater than 356.

In 2015 we tried to fix this issue by doing `= {};` on `dev_info`, which
unfortunately does not initialize that 4-byte hole. Fix it by using
memset() instead.

Cc: stable@vger.kernel.org
Fixes: c193fa91 ("drm/amdgpu: information leak in amdgpu_info_ioctl()")
Fixes: d38ceaf9

 ("drm/amdgpu: add core driver (v4)")
Suggested-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Peilin Ye <yepeilin.cs@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

This patch fixes a race condition that causes a use-after-free during
amdgpu_dm_atomic_commit_tail. This can occur when 2 non-blocking commits
are requested and the second one finishes before the first. Essentially,
this bug occurs when the following sequence of events happens:

1. Non-blocking commit #1 is requested w/ a new dm_state #1 and is
deferred to the workqueue.

2. Non-blocking commit #2 is requested w/ a new dm_state #2 and is
deferred to the workqueue.

3. Commit #2 starts before commit #1, dm_state #1 is used in the
commit_tail and commit #2 completes, freeing dm_state #1.

4. Commit #1 starts after commit #2 completes, uses the freed dm_state
1 and dereferences a freelist pointer while setting the context.

Since this bug has only been spotted with fast commits, this patch fixes
the bug by clearing the dm_state instead of using the old dc_state for
fast updates. In addition, since dm_state is only used for its dc_state
and amdgpu_dm_atomic_commit_tail will retain the dc_state if none is found,
removing the dm_state should not have any consequences in fast updates.

This use-after-free bug has existed for a while now, but only caused a
noticeable issue starting from 5.7-rc1 due to 3202fa62 ("slub: relocate
freelist pointer to middle of object") moving the freelist pointer from
dm_state->base (which was unused) to dm_state->context (which is
dereferenced).

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=207383
Fixes: bd200d19

 ("drm/amd/display: Don't replace the dc_state for fast updates")
Reported-by: Duncan <1i5t5.duncan@cox.net>
Signed-off-by: Mazin Rezk <mnrzk@protonmail.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Update GC golden setting for navy_flounder.

Signed-off-by: Jiansong Chen <Jiansong.Chen@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

It's in accordance with pmfw 65.5.0 for navy_flounder.

Signed-off-by: Jiansong Chen <Jiansong.Chen@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

add support for umc 8.7 initialization

add umc 8.7 source to makefile

Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: John Clements <john.clements@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

It doesn't expose PPTable descriptor on APU platform. So max/min
temperature values cannot be got from APU platform.

v2: Stoney needs to skip crit temperature as well.

Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Test expects that we also read HPD_IRQ_VECTOR when checking for
symbol loss as well lane status.

[How]
Read bytes 0x200-0x205 instead of just 0x202-0x205

Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
We need to be able to specify slice width for DSC on aconnector

[How]
Getting slice width parameter from debugfs entry, if it is
a valid the value is set in connector's dsc preffered settings
structure. Which then overwrites dsc_cfg structure's parameters
if DSC is decided to be enabled. Works for both SST and MST.

Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Mikita Lipski <Mikita.Lipski@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Feature requires synchronization of dig, pipe, and cursor locking
between driver and fw.

[How]
Set flag to force psr to use hw lock mgr.

Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
ramp_up_dispclk_with_dpp is to change dispclk, dppclk and dprefclk
according to bandwidth requirement. call stack: rv1_update_clocks -->
update_clocks --> dcn10_prepare_bandwidth / dcn10_optimize_bandwidth
--> prepare_bandwidth / optimize_bandwidth. before change dcn hw,
prepare_bandwidth will be called first to allow enough clock,
watermark for change, after end of dcn hw change, optimize_bandwidth
is executed to lower clock to save power for new dcn hw settings.

below is sequence of commit_planes_for_stream:
step 1: prepare_bandwidth - raise clock to have enough bandwidth
step 2: lock_doublebuffer_enable
step 3: pipe_control_lock(true) - make dchubp register change will
not take effect right way
step 4: apply_ctx_for_surface - program dchubp
step 5: pipe_control_lock(false) - dchubp register change take effect
step 6: optimize_bandwidth --> dc_post_update_surfaces_to_stream
for full_date, optimize clock to save power

at end of step 1, dcn clocks (dprefclk, dispclk, dppclk) may be
changed for new dchubp configuration. but real dcn hub dchubps are
still running with old configuration until end of step 5. this need
clocks settings at step 1 should not less than that before step 1.
this is checked by two conditions: 1. if (should_set_clock(safe_to_lower
, new_clocks->dispclk_khz, clk_mgr_base->clks.dispclk_khz) ||
new_clocks->dispclk_khz == clk_mgr_base->clks.dispclk_khz)
2. request_dpp_div = new_clocks->dispclk_khz > new_clocks->dppclk_khz

the second condition is based on new dchubp configuration. dppclk
for new dchubp may be different from dppclk before step 1.
for example, before step 1, dchubps are as below:
pipe 0: recout=(0,40,1920,980) viewport=(0,0,1920,979)
pipe 1: recout=(0,0,1920,1080) viewport=(0,0,1920,1080)
for dppclk for pipe0 need dppclk = dispclk

new dchubp pipe split configuration:
pipe 0: recout=(0,0,960,1080) viewport=(0,0,960,1080)
pipe 1: recout=(960,0,960,1080) viewport=(960,0,960,1080)
dppclk only needs dppclk = dispclk /2.

dispclk, dppclk are not lock by otg master lock. they take effect
after step 1. during this transition, dispclk are the same, but
dppclk is changed to half of previous clock for old dchubp
configuration between step 1 and step 6. This may cause p-state
warning intermittently.

[How]
for new_clocks->dispclk_khz == clk_mgr_base->clks.dispclk_khz, we
need make sure dppclk are not changed to less between step 1 and 6.
for new_clocks->dispclk_khz > clk_mgr_base->clks.dispclk_khz,
new display clock is raised, but we do not know ratio of
new_clocks->dispclk_khz and clk_mgr_base->clks.dispclk_khz,
new_clocks->dispclk_khz /2 does not guarantee equal or higher than
old dppclk. we could ignore power saving different between
dppclk = displck and dppclk = dispclk / 2 between step 1 and step 6.
as long as safe_to_lower = false, set dpclk = dispclk to simplify
condition check.

CC: Stable <stable@vger.kernel.org>
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Need a mechanism to force enable DSC on any connector

[How]
Debugfs entry overwrites newly added connector's dsc preffered
settings structure and sets dsc_clock_en flag on it.
During the attomic commit, depending if connector is SST or
MST, we will enable DSC manually by overwriting stream's DSC flag.

Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Mikita Lipski <Mikita.Lipski@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Each asic can optimize best based on its capabilities

[How]
Optimizing timing for a new pixel clock

Signed-off-by: Reza Amini <Reza.Amini@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Programming DCN is explicitly forbidden during idle optimzations allowed
state. Existing implemenation relies on OS/DM, which is not robust. Instead
DC should sequence this.

Note that DC will not re-enter idle optimized state on its own, it is only
responsible for catching out of sequence calls. It is still DM
responsibility to sequence appropriate for optimized power, but this change
removes the requirement for DM to cover the .1% case.

[How]
 - elevate updates during idle optimized state to full updates
 - disable idle power optimizations prior to programming

Signed-off-by: Jun Lei <jun.lei@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
Setting abm level does not correctly update CRTC state. As a result
no surface update is added to dc stream state and triggers warning.

[How]
Correctly update CRTC state when setting abm level property.

CC: Stable <stable@vger.kernel.org>
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Ported from radeon.

Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
All DCE6 specific code changes are guarded by CONFIG_DRM_AMD_DC_SI Kconfig option

[How]
(v1) CONFIG_DRM_AMD_DC_SI configuration option is added, default setting is disabled

(v2) Hainan is not supported, description updated accordingly

Tested with HD7750 (Cape Verde) and HD7950 (Tahiti)

Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
amdgpu_device.c requires changes for SI chipsets support
si.c require changes for Display Manager IP block enabling

[How]
amdgpu_device.c: add SI families in amdgpu_device_asic_has_dc_support()
si.c: changes in si_set_ip_blocks() for Display Manager IP blocks enablement

(v1) NOTE: As per Kaveri and older amdgpu.dc=1 kernel cmdline is required

(v2) fix for bc011f9350 ("drm/amdgpu: Change SI/CI gfx/sdma/smu init sequence")
     remove CHIP_HAINAN support since it does not have physical DCE6 module

Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
DCE6 chipsets do not support HW rotation

[How]
rotation property is created for Bonaire and later

Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
With all DCE6 specific macros, register, masks in place
dce60_resource.c may use them and become independent from DCE8 headers

[How]
(v1) Changelog:
- use DCE6 headers for registers and masks, remove the DC8 headers
- remove 7th Display Controller/Encoder register instances (DCE6 has only 6)
- use DCE6 specific watermark programming registers (DPG_PIPE_ARBITRATION_CONTROL3)
- use DCE6 specific input pixel processing registers shift/mask
- use DCE6 specific transform registers shift/mask
- use DCE6 specific link encoder registers shift/mask
- use DCE6 specific output pixel processing registers shift/mask
- use DCE6 specific audio registers shift/mask
- use DCE6 specific dmcu registers shift/mask
- use DCE6 specific hwseq registers shift/mask
- use DCE6 specific mem input registers shift/mask

(v2) Changelog:
- use DCE6 ad hoc dce60_mem_input_construct() function
- use DCE6 ad hoc dce60_transform_construct() function

(v3) Changelog:
- use DCE6 ad hoc dce60_ipp_construct() function

(v4) Changelog:
- use DCE6 ad hoc dce60_link_encoder_construct() function

(v5) Changelog:
- use DCE6 ad hoc dce60_opp_construct() function

(v6) Changelog:
- use DCE6 ad hoc dce60_audio_create() function

Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
DCE6 has CRTC_PREFETCH_EN bit in CRTC_CONTROL register
DCE6 has no CRTC_LEGACY_REQUESTOR_EN bit in CRTC_START_LINE_CONTROL register
DCE6 has no CRTC_CRC_CNTL register

[How]
Modify dce60_timing_generator_enable_advanced_request() function
Add dce60_configure_crc() function and dce60_is_tg_enabled() kept as static
Use dce60_configure_crc() function in dce60_tg_funcs

v2: remove unused variable (Alex)

Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
kernel WARNING due to use of .cursor_lock = dce_pipe_control_lock inherited by dce110

[How]
DCE6 set .cursor_lock = dce60_pipe_control_lock

Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
DCE6 has no bottom_pipe and no Blender HW
DCE6 needs 'blank_target' set to false in order to turn on the display
DCE6 has a specific dce60_pipe_control_lock() fuction that is a no op

[How]
Add DCE6 specific functions with needed private dce60_* dependent fuctions
Comment DCE6 specific CTRC program visibility implementation
Fix a typo in the initial header includes comment 's/DCE8/DCE6/g'
Use dce60_apply_ctx_for_surface() in dce60_hw_sequencer_construct
Use dce60_pipe_control_lock() in dce60_hw_sequencer_construct

v2: add missing return type (Alex)

Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
DCE6 has specific SCL_HORZ_FILTER_INIT_{LUMA_RGB,CHROMA} registers
In DCE6 h_init_luma and h_init_chroma initialization is required
Some DCE6 specific SCL_{HORZ,VERT}_FILTER_CONTROL masks were not listed

[How]
Add the registers and masks in dce_transform.h
Add DCE6 specific struct sclh_ratios_inits in dce_transform.h
Add dce60_calculate_inits() function
Add dce60_program_scl_ratios_inits() function
Fix dce60_transform_set_scaler() function

v2: remove unused variable (Alex)

Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
DCE6 has no SCL_MODE and no SCL_{HORZ,VERT}_FILTER_INIT registers
DCE6 has no SCL_BOUNDARY_MODE bit in SCL_CONTROL register
DCE6 has Line Buffer programming registers (DC_LB_MEMORY_SPLIT,DC_LB_MEM_SIZE)
DCE6 DATA_FORMAT register has only INTERLEAVE_EN bit
DCE6 has no Out Clamp Control programming registers (OUT_CLAMP_CONTROL_*)

[How]
Add DCE6 specific macros definitions for XFM registers and masks
Add DCE6 specific registers to dce_transform_registers struct
Add DCE6 specific masks to dce_transform_mask struct
DCE6 XFM macros/structs changes will avoid buiding errors when using DCE6 headers
Add dce60_setup_scaling_configuration() w/o missing Scaling registers/bit programming
Add dce60_transform_set_scaler() using DCE6 Line Buffer programming registers
Add dce60_program_bit_depth_reduction() w/o Out Clamp Control programming
Add dce60_transform_set_pixel_storage_depth() use dce60_program_bit_depth_reduction()
Use dce60_transform_set_scaler() in dce60_transform_funcs
Use dce60_transform_set_pixel_storage_depth() in dce60_transform_funcs
Add DCE6 specific dce60_transform_construct

Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
DCE6 has no FMT_TRUNCATE_MODE bit in FMT_BIT_DEPTH_CONTROL register
DCE6 has no FMT_CLAMP_COMPONENT_{R,G,B} registers
DCE6 has no FMT_SUBSAMPLING_{MODE,ORDER} bits in FMT_CONTROL register

[How]
Add DCE6 specific macros definitions for OPP registers and masks
DCE6 OPP macros will avoid buiding errors when using DCE6 headers
Add dce60_set_truncation() w/o FMT_TRUNCATE_MODE bit programming
Add dce60_opp_set_clamping() w/o Format Clamp Component programming
Add dce60_opp_program_fmt() w/o Format Subsampling bits programming
Add dce60_opp_program_bit_depth_reduction() with dce60_set_truncation
Use dce60_opp_program_fmt() in dce60_opp_funcs
Use dce60_opp_program_bit_depth_reduction() in dce60_opp_funcs
Add DCE6 specific dce60_opp_construct

Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
DCE6 has DPG_PIPE_ARBITRATION_CONTROL3 register for Line Buffer watermark selection
DCE6 has STUTTER_EXIT_SELF_REFRESH_WATERMARK_MASK mask for Stutter watermark selection
DCE6 has NB_PSTATE_CHANGE_WATERMARK_MASK mask for North Bridge watermark selection
DCE6 has no GRPH_MICRO_TILE_MODE mask
DCE6 has no HW_ROTATION register

[How]
Add DCE6 specific macros definitions for MI registers and masks
Add DCE6 specific registers to dce_mem_input_registers struct
Add DCE6 specific masks to dce_mem_input_masks struct
DCE6 MI macros/structs changes will avoid buiding errors when using DCE6 headers
Add dce60_program_urgency_watermark() function
Add dce60_program_nbp_watermark() function
Add dce60_program_stutter_watermark() function
Add dce60_mi_program_display_marks() function w/ new DCE6 watermark programming
Add DCE6 specific tiling programming and modify DCE8 case
Add dce60_program_size() fuction w/o Rotation processing
Add dce60_mi_program_surface_config() fuction
Use dce60_mi_program_display_marks() in dce60_mi_funcs
Use dce60_mi_program_surface_config() in dce60_mi_funcs
Add DCE6 specific dce60_mem_input_construct

v2: remove unused variable (Alex)

Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
DCE6 has no DP_DPHY_SCRAM_CNTL register

[How]
Add DCE6 specific macros definitions for LE registers
DCE6 LE macros will avoid buiding errors when using DCE6 headers
Add dce60_set_dp_phy_pattern_hbr2_compliance_cp2520_2() w/o Scramble Control programming
Add dce60_set_dp_phy_pattern_passthrough_mode() w/o Scramble Control programming
Add dce60_configure_encoder() w/o Scramble Control programming
Add dce60_link_encoder_enable_dp_output() w/ dce60_configure_encoder
Add dce60_link_encoder_enable_dp_mst_output() w/ dce60_configure_encoder
Add dce60_link_encoder_dp_set_phy_pattern() w/ dce60_set_dp_phy_pattern_passthrough_mode
Use dce60_link_encoder_enable_dp_output() in dce60_lnk_enc_funcs
Use dce60_link_encoder_enable_dp_mst_output() in dce60_lnk_enc_funcs
Use dce60_link_encoder_dp_set_phy_pattern() in dce60_lnk_enc_funcs
Add DCE6 specific dce60_link_encoder_construct

Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
DCE6 does not have CURSOR2_DEGAMMA_MODE bit in DEGAMMA_CONTROL register

[How]
Add DCE6 specific macros definitions for IPP masks
DCE6 IPP macros will avoid buiding errors when using DCE6 headers
Add dce60_ipp_set_degamma() function w/o Cursor2 Degamma programming
Use dce60_ipp_set_degamma() in ipp_funcs dce60_ipp_funcs
Add DCE6 specific dce60_ipp_construct

Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
DCE6 has no BLND_CONTROL register for Blender HW programming
DCE6 has no BLND_V_UPDATE_LOCK register for Pipe Locking

[How]
Add DCE6 specific macros definitions for HWSEQ registers and masks
DCE6 HWSEQ macros will avoid buiding errors when using DCE6 headers
Add dce60_pipe_control_lock() stub with no op

Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mauro Rossi <issor.oruam@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>