- Apr 20, 2020
-
-
Andre Guedes authored
With the previous two patches, igc_add_mac_steering_filter() and igc_del_mac_steering_filter() became a pointless wrapper of igc_add_mac_filter() and igc_del_mac_filter(). This patch removes these wrappers and update callers to call igc_add_mac_filter() and igc_del_mac_filter() directly. Signed-off-by:
Andre Guedes <andre.guedes@intel.com> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Andre Guedes authored
The IGC_MAC_STATE_QUEUE_STEERING bit in mac_table[i].state is utilized to indicate that frames matching the filter are assigned to mac_table[i].queue. This bit is not strictly necessary since we can convey the same information as follows: queue == -1 means queue assignment is disabled, otherwise it is enabled. In addition to make the code simpler, this change fixes some awkward situations where we pass a complete misleading 'queue' value such as in igc_uc_sync(). So this patch removes IGC_MAC_STATE_QUEUE_STEERING and also takes the opportunity to improve the igc_add_mac_filter documentation. Signed-off-by:
Andre Guedes <andre.guedes@intel.com> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Andre Guedes authored
igc_add_mac_filter() doesn't allow us to have more than one entry with the same address and address type in adapter->mac_table so checking if 'queue' matches in igc_del_mac_filter() isn't necessary. This patch removes that check. This patch also takes the opportunity to improve the igc_del_mac_filter documentation and remove comment which is not applicable to this I225 controller. Signed-off-by:
Andre Guedes <andre.guedes@intel.com> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Andre Guedes authored
igc_add_mac_filter() doesn't allow filters with invalid MAC address to be added to adapter->mac_table so, in igc_del_mac_filter(), we can early return if MAC address is invalid. No need to traverse the table. Signed-off-by:
Andre Guedes <andre.guedes@intel.com> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Andre Guedes authored
Current igc_rar_set_index() implementation is a bit convoluted so this patch does some code refactoring to improve it. The helper igc_rar_set_index() is about writing MAC filter settings into hardware registers. Logic such as address validation belongs to functions upper in the call chain such as igc_set_mac() and igc_add_mac_filter(). So this patch moves the is_valid_ether_addr() call to igc_add_mac_filter(). No need to touch igc_set_mac() since it already checks it. The variables 'rar_low' and 'rar_high' represent the value in registers RAL and RAH so we rename them to 'ral' and 'rah', respectively, to match the registers names. To make it explicit, filter settings are passed as arguments to the function instead of reading them from adapter->mac_table "under the hood". Also, the function was renamed to igc_set_mac_filter_hw to make it more clear what it does. Finally, the patch removes some wrfl() calls and comments not needed. Signed-off-by:
Andre Guedes <andre.guedes@intel.com> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Andre Guedes authored
In case igc_del_mac_filter() returns error, that error is masked since the functions always return 0 (success). This patch fixes igc_uc_unsync() so it returns whatever value igc_del_mac_filter() returns (0 on success, negative number on error). Signed-off-by:
Andre Guedes <andre.guedes@intel.com> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Andre Guedes authored
In case of success, igc_add_mac_filter() returns the index in adapter->mac_table where the requested filter was added. This information, however, is not used by any caller of that function. In fact, callers have extra code just to handle this returning index as 0 (success). So this patch changes the function to return 0 on success instead, and cleans up the extra code. Signed-off-by:
Andre Guedes <andre.guedes@intel.com> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Andre Guedes authored
The IGC_MAC_STATE_SRC_ADDR flags is not supported by igc_add_mac_ filter() so this patch adds a check for it and returns -ENOTSUPP in case it is set. Signed-off-by:
Andre Guedes <andre.guedes@intel.com> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Andre Guedes authored
This patch does a code refactoring in the MAC address filtering logic to get rid of some duplicate code. IGC driver has two functions to add MAC address filters that are pretty much the same: igc_add_mac_filter() and igc_add_mac_filter_flags(). The only difference is that the latter allows the callee to specify the 'flags' parameter while the former has it hard coded as zero. The same rationale applies to filter deletion counterparts. So this patch refactors igc_add_mac_filter() and igc_del_mac_filter() so they handle the 'flags' parameters, removes the _flags() functions, and fixes callees accordingly. Signed-off-by:
Andre Guedes <andre.guedes@intel.com> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Vitaly Lifshits authored
Added a fix to S0ix entry and exit flows for TGP and above MAC types, to the case when the Ethernet cable is connected and the link is up. With that the system is able to reach SLP_S0 when going to freeze power state. Signed-off-by:
Vitaly Lifshits <vitaly.lifshits@intel.com> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Sasha Neftin authored
Add new device IDs for the next step of i225 Signed-off-by:
Sasha Neftin <sasha.neftin@intel.com> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
- Apr 19, 2020
-
-
David S. Miller authored
Heiner Kallweit says: ==================== r8169: series with improvements Again a series with few improvements. ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Heiner Kallweit authored
Add workaround for hw issues with TSO on RTL8168evl. This workaround is based on information I got from Realtek, and *should* allow to safely enable TSO on this chip version. Signed-off-by:
Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Heiner Kallweit authored
Simplify the code and avoid the overhead of calling vlan_get_protocol(). Signed-off-by:
Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Heiner Kallweit authored
At that place in rtl_init_one() we can safely use rtl8169_set_features() to configure the chip according to the default features. Signed-off-by:
Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Heiner Kallweit authored
So far we set RX_VLAN_8125 unconditionally, even if NETIF_F_HW_VLAN_CTAG_RX may not be set. Don't touch these bits, and let only rtl8169_set_features() control them. Signed-off-by:
Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Heiner Kallweit authored
NETIF_F_HIGHDMA is added to vlan_features by register_netdev(), therefore we can omit this here. Signed-off-by:
Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Heiner Kallweit authored
Move setting the ocp_base to rtl_init_one(). Where supported the value is always the same, and if not supported it doesn't hurt. Signed-off-by:
Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Vladimir Oltean authored
Each ENETC station interface (SI) has a VLAN filter list and a port flag (PSIPVMR) by which it can be put in "VLAN promiscuous" mode, which enables the reception of VLAN-tagged traffic even if it is not in the VLAN filtering list. Currently the handling of this setting works like this: the port starts off as VLAN promiscuous, then it switches to enabling VLAN filtering as soon as the first VLAN is installed in its filter via .ndo_vlan_rx_add_vid. In practice that does not work out very well, because more often than not, the first VLAN to be installed is out of the control of the user: the 8021q module, if loaded, adds its rule for 802.1p (VID 0) traffic upon bringing the interface up. What the user is currently seeing in ethtool is this: ethtool -k eno2 rx-vlan-filter: on [fixed] which doesn't match the intention of the code, but the practical reality of having the 8021q module install its VID which has the side-effect of turning on VLAN filtering in this driver. All in all, a slightly confusing experience. So instead of letting this driver switch the VLAN filtering state by itself, just wire it up with the rx-vlan-filter feature from ethtool, and let it be user-configurable just through that knob, except for one case, see below. In promiscuous mode, it is more intuitive that all traffic is received, including VLAN tagged traffic. It appears that it is necessary to set the flag in PSIPVMR for that to be the case, so VLAN promiscuous mode is also temporarily enabled. On exit from promiscuous mode, the setting made by ethtool is restored. Signed-off-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by:
Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Vladimir Oltean authored
By default, the VCAP IS2 will produce a single match for each frame, on the most specific classification. Example: a ping packet (ICMP over IPv4 over Ethernet) sent from an IP address of 10.0.0.1 and a MAC address of 96:18:82:00:04:01 will match this rule: tc filter add dev swp0 ingress protocol ipv4 \ flower skip_sw src_ip 10.0.0.1 action drop but not this one: tc filter add dev swp0 ingress \ flower skip_sw src_mac 96:18:82:00:04:01 action drop Currently the driver does not really warn the user in any way about this, and the behavior is rather strange anyway. The current patch is a workaround to force matches on MAC_ETYPE keys (DMAC and SMAC) for all packets irrespective of higher layer protocol. The setting is made at the port level. Of course this breaks all other non-src_mac and non-dst_mac matches, so rule exclusivity checks have been added to the driver, in order to never have rules of both types on any ingress port. The bits that discard higher-level protocol information are set only once a MAC_ETYPE rule is added to a filter block, and only for the ports that are bound to that filter block. Then all further non-MAC_ETYPE rules added to that filter block should be denied by the ports bound to it. Signed-off-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queueDavid S. Miller authored
Jeff Kirsher says: ==================== 1GbE Intel Wired LAN Driver Updates 2020-04-17 This series contains updates to e1000e and igc only. Sasha adds partial generic segmentation offload (GSO partial) support to the igc driver. Also added support for translating taprio schedules into i225 cycles in igc. Did clean up of dead code or unused defines in the igc driver. Refactored the code to avoid forward declarations where possible. Enables the NETIF_F_HW_TC flag for igc by default. Vinicius adds support for ETF offloading using the similar approach that taprio offload used. Kees Cook fixes a clang warning in the e1000e driver by moving the declared variable either into the switch case that uses the variable or lift them up into the main function body, to help the compiler. Andre fixed some register overwriting when dumping registers via ethtool for igc driver. Also fixed support for ethtool Network Flow Classification (NFC) queue redirection by adding the missing code needed to enable the queue selection feature from Receive Address High (RAH) register. Cleans up code to remove the code bits designed to support tc-flower filters, since this client part does not support it. ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Florian Fainelli authored
BCM53125 has internal Gigabit PHYs which support interrupts as well as statistics, make it possible to configure both of those features with a PHY driver entry. Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Florian Fainelli authored
Displaying the virtual address at which the MDIO base register address has been mapped is not useful and is not visible with pointer hashing in place, replace the message with something indicating successful registration instead. Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Florian Fainelli authored
Make use of platform_get_irq_byname_optional() to avoid printing messages on the kernel console that interrupts cannot be found. Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David Bauer authored
This adds support for the Qualcomm Atheros AR8032 Fast Ethernet PHY. It shares many similarities with the already supported AR8030 PHY but additionally supports MII connection to the MAC. Signed-off-by:
David Bauer <mail@david-bauer.net> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
- Apr 18, 2020
-
-
David S. Miller authored
Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next Johan Hedberg says: ==================== pull request: bluetooth-next 2020-04-17 Here's the first bluetooth-next pull request for the 5.8 kernel: - Added debugfs option to control MITM flag usage during pairing - Added new BT_MODE socket option - Added support for Qualcom QCA6390 device - Added support for Realtek RTL8761B device - Added support for mSBC audio codec over USB endpoints - Added framework for Microsoft HCI vendor extensions - Added new Read Security Information management command - Fixes/cleanup to link layer privacy related code - Various other smaller cleanups & fixes ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Andre Guedes authored
This patch fixes a bug when the user adds the first MAC address filter via ethtool NFC mechanism. When the first MAC address filter is added, it overwrites the default MAC address filter configured at RAL[0] and RAH[0]. As consequence, frames addressed to the interface MAC address are not sent to host anymore. This patch fixes the bug by calling igc_set_default_mac_filter() during adapter init so the position 0 of adapter->mac_table[] is assigned to the default MAC address. Signed-off-by:
Andre Guedes <andre.guedes@intel.com> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Andre Guedes authored
IGC driver has no support for tc-flower filters so this patch removes some leftover code, probably copied from IGB driver by mistake. Signed-off-by:
Andre Guedes <andre.guedes@intel.com> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Andre Guedes authored
The support for ethtool Network Flow Classification (NFC) queue redirection based on destination MAC address is currently broken in IGC. For instance, if we add the following rule, matching frames aren't enqueued on the expected rx queue. $ ethtool -N IFNAME flow-type ether dst 3c:fd:fe:9e:7f:71 queue 2 The issue here is due to the fact that igc_rar_set_index() is missing code to enable the queue selection feature from Receive Address High (RAH) register. This patch adds the missing code and fixes the issue. Signed-off-by:
Andre Guedes <andre.guedes@intel.com> Acked-by:
Sasha Neftin <sasha.neftin@intel.com> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Sasha Neftin authored
i225 device support copper mode only PHY signal detect indication for copper fiber switch not applicable to i225 part Signed-off-by:
Sasha Neftin <sasha.neftin@intel.com> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Sasha Neftin authored
This assignment of the feature NETIF_F_HW_TC occurs prior to the initial setup of the local hw_features variable. This ensures that NETIF_F_HW_TC are marked as user changeable, and also enables it by default when the driver loads. Signed-off-by:
Sasha Neftin <sasha.neftin@intel.com> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Sasha Neftin authored
IGC_START_ITR has beed defined twice This patch come to fix it Signed-off-by:
Sasha Neftin <sasha.neftin@intel.com> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Andre Guedes authored
This patch fixes some register overwriting when dumping registers via ethtool. We have a total of 16 RAL registers, starting at offset 139. So RAH offset should be 139 + 16 = 155, not 145. As result some RAL registers are overwritten. Likewise, RAH registers are also overwritten by TDBAL, TDBAH, TDLEN, and TDH registers. To fix this bug while preserving the ABI, this patch re-writes RAL and RAH registers at the end of 'regs_buff' and bumps regs->version. It also removes some pointless comments in the middle of igc_set_regs(). Signed-off-by:
Andre Guedes <andre.guedes@intel.com> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Sasha Neftin authored
Move igc_adapter and igc_ring structures up to avoid forward declaration It is not necessary to forward declare these structures Signed-off-by:
Sasha Neftin <sasha.neftin@intel.com> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Sasha Neftin authored
We support only copper mode Not applicable for i225 parts Signed-off-by:
Sasha Neftin <sasha.neftin@intel.com> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Sasha Neftin authored
Formally Destination bit should be kept reserved to support legacy drivers and ignore on write/read operation Not applicable for i225 parts Signed-off-by:
Sasha Neftin <sasha.neftin@intel.com> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Kees Cook authored
Variables declared in a switch statement before any case statements cannot be automatically initialized with compiler instrumentation (as they are not part of any execution flow). With GCC's proposed automatic stack variable initialization feature, this triggers a warning (and they don't get initialized). Clang's automatic stack variable initialization (via CONFIG_INIT_STACK_ALL=y) doesn't throw a warning, but it also doesn't initialize such variables[1]. Note that these warnings (or silent skipping) happen before the dead-store elimination optimization phase, so even when the automatic initializations are later elided in favor of direct initializations, the warnings remain. To avoid these problems, move such variables into the "case" where they're used or lift them up into the main function body. drivers/net/ethernet/intel/e1000/e1000_main.c: In function ‘e1000_xmit_frame’: drivers/net/ethernet/intel/e1000/e1000_main.c:3143:18: warning: statement will never be executed [-Wswitch-unreachable] 3143 | unsigned int pull_size; | ^~~~~~~~~ [1] https://bugs.llvm.org/show_bug.cgi?id=44916 Signed-off-by:
Kees Cook <keescook@chromium.org> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Vinicius Costa Gomes authored
This adds support for ETF offloading for the i225 controller. For i225, the LaunchTime feature is almost a subset of the Qbv feature. The main change from the i210 is that the launchtime of each packet is specified as an offset applied to the BASET register. BASET is automatically incremented each cycle. For i225, the approach chosen is to re-use most of the setup used for taprio offloading. With a few changes: - The more or less obvious one is that when ETF is enabled, we should set add the expected launchtime to the (advanced) transmit descriptor; - The less obvious, is that when taprio offloading is not enabled, we add a dummy schedule (all queues are open all the time, with a cycle time of 1 second). Signed-off-by:
Vinicius Costa Gomes <vinicius.gomes@intel.com> Reviewed-by:
Andre Guedes <andre.guedes@intel.com> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Vinicius Costa Gomes authored
Adds support for translating taprio schedules into i225 cycles. This will allow schedules to run in the hardware, making the schedules enforcement more precise and saving CPU time. Right now, the only simple schedules are allowed, complex schedules are rejected. "simple" in this context are schedules that each HW queue is opened and closed only once in each cycle. Changing schedules is still not supported as well. Signed-off-by:
Vinicius Costa Gomes <vinicius.gomes@intel.com> Reviewed-by:
Andre Guedes <andre.guedes@intel.com> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Sasha Neftin authored
Partial generic segmentation offload is a hybrid between TSO and GSO. What is effectively does is take advantage of certain traits of TCP and tunnels so that instead of having to rewrite the packet headers for each segment only in the inner-most transport header and possible the outer-most network header need to be updated. This allows devices that do not support tunnel offload or tunnels offloads with checksum to still make use of segmentation. Signed-off-by:
Sasha Neftin <sasha.neftin@intel.com> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-