This reverts commit 56573604.

According to the commit, it implements a manual AN-37 for some
"troublesome" Juniper MX5 switches. This appears to be a workaround for a
particular switch.

It has been reported that this causes a severe breakage for other switches,
including a Cisco 3560CX-12PD-S.

The code appears to be a workaround for a specific switch which fails to
link in SFI mode. It expects to see AN-37 auto negotiation in order to
link. The Cisco switch is not expecting AN-37 auto negotiation. When the
device starts the manual AN-37, the Cisco switch decides that the port is
confused and stops attempting to link with it. This persists until a power
cycle. A simple driver unload and reload does not resolve the issue, even
if loading with a version of the driver which lacks this workaround.

The authors of the workaround commit have not responded with
clarifications, and the result of the workaround is complete failure to
connect with other switches.

This appears to be a case where the driver can either "correctly" link with
the Juniper MX5 switch, at the cost of bricking the link with the Cisco
switch, or it can behave properly for the Cisco switch, but fail to link
with the Junipir MX5 switch. I do not know enough about the standards
involved to clearly determine whether either switch is at fault or behaving
incorrectly. Nor do I know whether there exists some alternative fix which
corrects behavior with both switches.

Revert the workaround for the Juniper switch.

Fixes: 56573604

 ("ixgbe: Manual AN-37 for troublesome link partners for X550 SFI")
Link: https://lore.kernel.org/netdev/cbe874db-9ac9-42b8-afa0-88ea910e1e99@intel.com/T/
Link: https://forum.proxmox.com/threads/intel-x553-sfp-ixgbe-no-go-on-pve8.135129/#post-612291
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Jeff Daly <jeffd@silicom-usa.com>
Cc: kernel.org-fo5k2w@ycharbi.fr
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240520-net-2024-05-20-revert-silicom-switch-workaround-v1-1-50f80f261c94@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Testing a network device that has large numbers of bytes/packets may
overflow. Using stats64 when comparing fixes this problem.

I tripped on this while iterating on a qstats patch for mlx5. See below
for confirmation without my added code that this is a bug.

Before this patch (with added debugging output):

$ NETIF=eth0 tools/testing/selftests/drivers/net/stats.py
KTAP version 1
1..4
ok 1 stats.check_pause
ok 2 stats.check_fec
rstat: 481708634 qstat: 666201639514 key: tx-bytes
not ok 3 stats.pkt_byte_sum
ok 4 stats.qstat_by_ifindex

Note the huge delta above ^^^ in the rtnl vs qstats.

After this patch:

$ NETIF=eth0 tools/testing/selftests/drivers/net/stats.py
KTAP version 1
1..4
ok 1 stats.check_pause
ok 2 stats.check_fec
ok 3 stats.pkt_byte_sum
ok 4 stats.qstat_by_ifindex

It looks like rtnl_fill_stats in net/core/rtnetlink.c will attempt to
copy the 64bit stats into a 32bit structure which is probably why this
behavior is occurring.

To show this is happening, you can get the underlying stats that the
stats.py test uses like this:

$ ./cli.py --spec ../../../Documentation/netlink/specs/rt_link.yaml \
           --do getlink --json '{"ifi-index": 7}'

And examine the output (heavily snipped to show relevant fields):

 'stats': {
           'multicast': 3739197,
           'rx-bytes': 1201525399,
           'rx-packets': 56807158,
           'tx-bytes': 492404458,
           'tx-packets': 1200285371,

 'stats64': {
             'multicast': 3739197,
             'rx-bytes': 35561263767,
             'rx-packets': 56807158,
             'tx-bytes': 666212335338,
             'tx-packets': 1200285371,

The stats.py test prior to this patch was using the 'stats' structure
above, which matches the failure output on my system.

Comparing side by side, rx-bytes and tx-bytes, and getting ethtool -S
output:

rx-bytes stats:    1201525399
rx-bytes stats64: 35561263767
rx-bytes ethtool: 36203402638

tx-bytes stats:      492404458
tx-bytes stats64: 666212335338
tx-bytes ethtool: 666215360113

Note that the above was taken from a system with an mlx5 NIC, which only
exposes ndo_get_stats64.

Based on the ethtool output and qstat output, it appears that stats.py
should be updated to use the 'stats64' structure for accurate
comparisons when packet/byte counters get very large.

To confirm that this was not related to the qstats code I was iterating
on, I booted a kernel without my driver changes and re-ran the test
which shows the qstats are skipped (as they don't exist for mlx5):

NETIF=eth0 tools/testing/selftests/drivers/net/stats.py
KTAP version 1
1..4
ok 1 stats.check_pause
ok 2 stats.check_fec
ok 3 stats.pkt_byte_sum # SKIP qstats not supported by the device
ok 4 stats.qstat_by_ifindex # SKIP No ifindex supports qstats

But, fetching the stats using the CLI

$ ./cli.py --spec ../../../Documentation/netlink/specs/rt_link.yaml \
           --do getlink --json '{"ifi-index": 7}'

Shows the same issue (heavily snipped for relevant fields only):

 'stats': {
           'multicast': 105489,
           'rx-bytes': 530879526,
           'rx-packets': 751415,
           'tx-bytes': 2510191396,
           'tx-packets': 27700323,
 'stats64': {
             'multicast': 105489,
             'rx-bytes': 530879526,
             'rx-packets': 751415,
             'tx-bytes': 15395093284,
             'tx-packets': 27700323,

Comparing side by side with ethtool -S on the unmodified mlx5 driver:

tx-bytes stats:    2510191396
tx-bytes stats64: 15395093284
tx-bytes ethtool: 17718435810

Fixes: f0e6c86e

 ("testing: net-drv: add a driver test for stats reporting")
Signed-off-by: Joe Damato <jdamato@fastly.com>
Link: https://lore.kernel.org/r/20240520235850.190041-1-jdamato@fastly.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Commit 62c1bff5 added an extra HZ along with msecs_to_jiffies.
This patch fixes that.

Cc: stable@vger.kernel.org
Fixes: 62c1bff5

 ("net: mana: Configure hwc timeout from hardware")
Signed-off-by: Souradeep Chakrabarti <schakrabarti@linux.microsoft.com>
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Link: https://lore.kernel.org/r/1716185104-31658-1-git-send-email-schakrabarti@linux.microsoft.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Lan966x is adding ptp traps to redirect the ptp frames to the CPU such
that the HW will not forward these frames anywhere. The issue is that in
case ptp is not enabled and the timestamping source is et to
HWTSTAMP_SOURCE_NETDEV then these traps would not be removed on the
error path.
Fix this by removing the traps in this case as they are not needed.

Fixes: 54e1ed69

 ("net: lan966x: convert to ndo_hwtstamp_get() and ndo_hwtstamp_set()")
Suggested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20240517135808.3025435-1-horatiu.vultur@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Open vSwitch is originally intended to switch at layer 2, only dealing with
Ethernet frames.  With the introduction of l3 tunnels support, it crossed
into the realm of needing to care a bit about some routing details when
making forwarding decisions.  If an oversized packet would need to be
fragmented during this forwarding decision, there is a chance for pmtu
to get involved and generate a routing exception.  This is gated by the
skbuff->pkt_type field.

When a flow is already loaded into the openvswitch module this field is
set up and transitioned properly as a packet moves from one port to
another.  In the case that a packet execute is invoked after a flow is
newly installed this field is not properly initialized.  This causes the
pmtud mechanism to omit sending the required exception messages across
the tunnel boundary and a second attempt needs to be made to make sure
that the routing exception is properly setup.  To fix this, we set the
outgoing packet's pkt_type to PACKET_OUTGOING, since it can only get
to the openvswitch module via a port device or packet command.

Even for bridge ports as users, the pkt_type needs to be reset when
doing the transmit as the packet is truly outgoing and routing needs
to get involved post packet transformations, in the case of
VXLAN/GENEVE/udp-tunnel packets.  In general, the pkt_type on output
gets ignored, since we go straight to the driver, but in the case of
tunnel ports they go through IP routing layer.

This issue is periodically encountered in complex setups, such as large
openshift deployments, where multiple sets of tunnel traversal occurs.
A way to recreate this is with the ovn-heater project that can setup
a networking environment which mimics such large deployments.  We need
larger environments for this because we need to ensure that flow
misses occur.  In these environment, without this patch, we can see:

  ./ovn_cluster.sh start
  podman exec ovn-chassis-1 ip r a 170.168.0.5/32 dev eth1 mtu 1200
  podman exec ovn-chassis-1 ip netns exec sw01p1 ip r flush cache
  podman exec ovn-chassis-1 ip netns exec sw01p1 \
         ping 21.0.0.3 -M do -s 1300 -c2
  PING 21.0.0.3 (21.0.0.3) 1300(1328) bytes of data.
  From 21.0.0.3 icmp_seq=2 Frag needed and DF set (mtu = 1142)

  --- 21.0.0.3 ping statistics ---
  ...

Using tcpdump, we can also see the expected ICMP FRAG_NEEDED message is not
sent into the server.

With this patch, setting the pkt_type, we see the following:

  podman exec ovn-chassis-1 ip netns exec sw01p1 \
         ping 21.0.0.3 -M do -s 1300 -c2
  PING 21.0.0.3 (21.0.0.3) 1300(1328) bytes of data.
  From 21.0.0.3 icmp_seq=1 Frag needed and DF set (mtu = 1222)
  ping: local error: message too long, mtu=1222

  --- 21.0.0.3 ping statistics ---
  ...

In this case, the first ping request receives the FRAG_NEEDED message and
a local routing exception is created.

Tested-by: Jaime Caamano <jcaamano@redhat.com>
Reported-at: https://issues.redhat.com/browse/FDP-164
Fixes: 58264848

 ("openvswitch: Add vxlan tunneling support.")
Signed-off-by: Aaron Conole <aconole@redhat.com>
Acked-by: Eelco Chaudron <echaudro@redhat.com>
Link: https://lore.kernel.org/r/20240516200941.16152-1-aconole@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Michal Luczaj says:

====================
af_unix: Fix GC and improve selftest

Series deals with AF_UNIX garbage collector mishandling some in-flight
graph cycles. Embryos carrying OOB packets with SCM_RIGHTS cause issues.

Patch 1/2 fixes the memory leak.
Patch 2/2 tweaks the selftest for a better OOB coverage.

v3:
  - Patch 1/2: correct the commit message (Kuniyuki)

v2: https://lore.kernel.org/netdev/20240516145457.1206847-1-mhal@rbox.co/
  - Patch 1/2: remove WARN_ON_ONCE() (Kuniyuki)
  - Combine both patches into a series (Kuniyuki)

v1: https://lore.kernel.org/netdev/20240516103049.1132040-1-mhal@rbox.co/
====================

Link: https://lore.kernel.org/r/20240517093138.1436323-1-mhal@rbox.co
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

scm_rights.c covers various test cases for inflight file descriptors
and garbage collector for AF_UNIX sockets.

Currently, SCM_RIGHTS messages are sent with 3-bytes string, and it's
not good for MSG_OOB cases, as SCM_RIGTS cmsg goes with the first 2-bytes,
which is non-OOB data.

Let's send SCM_RIGHTS messages with 1-byte character to pack SCM_RIGHTS
into OOB data.

Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Michal Luczaj <mhal@rbox.co>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

GC attempts to explicitly drop oob_skb's reference before purging the hit
list.

The problem is with embryos: kfree_skb(u->oob_skb) is never called on an
embryo socket.

The python script below [0] sends a listener's fd to its embryo as OOB
data.  While GC does collect the embryo's queue, it fails to drop the OOB
skb's refcount.  The skb which was in embryo's receive queue stays as
unix_sk(sk)->oob_skb and keeps the listener's refcount [1].

Tell GC to dispose embryo's oob_skb.

[0]:
from array import array
from socket import *

addr = '\x00unix-oob'
lis = socket(AF_UNIX, SOCK_STREAM)
lis.bind(addr)
lis.listen(1)

s = socket(AF_UNIX, SOCK_STREAM)
s.connect(addr)
scm = (SOL_SOCKET, SCM_RIGHTS, array('i', [lis.fileno()]))
s.sendmsg([b'x'], [scm], MSG_OOB)
lis.close()

[1]
$ grep unix-oob /proc/net/unix
$ ./unix-oob.py
$ grep unix-oob /proc/net/unix
0000000000000000: 00000002 00000000 00000000 0001 02     0 @unix-oob
0000000000000000: 00000002 00000000 00010000 0001 01  6072 @unix-oob

Fixes: 4090fa37

 ("af_unix: Replace garbage collection algorithm.")
Signed-off-by: Michal Luczaj <mhal@rbox.co>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

In dctcp_update_alpha(), we use a module parameter dctcp_shift_g
as follows:

  alpha -= min_not_zero(alpha, alpha >> dctcp_shift_g);
  ...
  delivered_ce <<= (10 - dctcp_shift_g);

It seems syzkaller started fuzzing module parameters and triggered
shift-out-of-bounds [0] by setting 100 to dctcp_shift_g:

  memcpy((void*)0x20000080,
         "/sys/module/tcp_dctcp/parameters/dctcp_shift_g\000", 47);
  res = syscall(__NR_openat, /*fd=*/0xffffffffffffff9cul, /*file=*/0x20000080ul,
                /*flags=*/2ul, /*mode=*/0ul);
  memcpy((void*)0x20000000, "100\000", 4);
  syscall(__NR_write, /*fd=*/r[0], /*val=*/0x20000000ul, /*len=*/4ul);

Let's limit the max value of dctcp_shift_g by param_set_uint_minmax().

With this patch:

  # echo 10 > /sys/module/tcp_dctcp/parameters/dctcp_shift_g
  # cat /sys/module/tcp_dctcp/parameters/dctcp_shift_g
  10
  # echo 11 > /sys/module/tcp_dctcp/parameters/dctcp_shift_g
  -bash: echo: write error: Invalid argument

[0]:
UBSAN: shift-out-of-bounds in net/ipv4/tcp_dctcp.c:143:12
shift exponent 100 is too large for 32-bit type 'u32' (aka 'unsigned int')
CPU: 0 PID: 8083 Comm: syz-executor345 Not tainted 6.9.0-05151-g1b294a1f3561 #2
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
1.13.0-1ubuntu1.1 04/01/2014
Call Trace:
 <TASK>
 __dump_stack lib/dump_stack.c:88 [inline]
 dump_stack_lvl+0x201/0x300 lib/dump_stack.c:114
 ubsan_epilogue lib/ubsan.c:231 [inline]
 __ubsan_handle_shift_out_of_bounds+0x346/0x3a0 lib/ubsan.c:468
 dctcp_update_alpha+0x540/0x570 net/ipv4/tcp_dctcp.c:143
 tcp_in_ack_event net/ipv4/tcp_input.c:3802 [inline]
 tcp_ack+0x17b1/0x3bc0 net/ipv4/tcp_input.c:3948
 tcp_rcv_state_process+0x57a/0x2290 net/ipv4/tcp_input.c:6711
 tcp_v4_do_rcv+0x764/0xc40 net/ipv4/tcp_ipv4.c:1937
 sk_backlog_rcv include/net/sock.h:1106 [inline]
 __release_sock+0x20f/0x350 net/core/sock.c:2983
 release_sock+0x61/0x1f0 net/core/sock.c:3549
 mptcp_subflow_shutdown+0x3d0/0x620 net/mptcp/protocol.c:2907
 mptcp_check_send_data_fin+0x225/0x410 net/mptcp/protocol.c:2976
 __mptcp_close+0x238/0xad0 net/mptcp/protocol.c:3072
 mptcp_close+0x2a/0x1a0 net/mptcp/protocol.c:3127
 inet_release+0x190/0x1f0 net/ipv4/af_inet.c:437
 __sock_release net/socket.c:659 [inline]
 sock_close+0xc0/0x240 net/socket.c:1421
 __fput+0x41b/0x890 fs/file_table.c:422
 task_work_run+0x23b/0x300 kernel/task_work.c:180
 exit_task_work include/linux/task_work.h:38 [inline]
 do_exit+0x9c8/0x2540 kernel/exit.c:878
 do_group_exit+0x201/0x2b0 kernel/exit.c:1027
 __do_sys_exit_group kernel/exit.c:1038 [inline]
 __se_sys_exit_group kernel/exit.c:1036 [inline]
 __x64_sys_exit_group+0x3f/0x40 kernel/exit.c:1036
 do_syscall_x64 arch/x86/entry/common.c:52 [inline]
 do_syscall_64+0xe4/0x240 arch/x86/entry/common.c:83
 entry_SYSCALL_64_after_hwframe+0x67/0x6f
RIP: 0033:0x7f6c2b5005b6
Code: Unable to access opcode bytes at 0x7f6c2b50058c.
RSP: 002b:00007ffe883eb948 EFLAGS: 00000246 ORIG_RAX: 00000000000000e7
RAX: ffffffffffffffda RBX: 00007f6c2b5862f0 RCX: 00007f6c2b5005b6
RDX: 0000000000000001 RSI: 000000000000003c RDI: 0000000000000001
RBP: 0000000000000001 R08: 00000000000000e7 R09: ffffffffffffffc0
R10: 0000000000000006 R11: 0000000000000246 R12: 00007f6c2b5862f0
R13: 0000000000000001 R14: 0000000000000000 R15: 0000000000000001
 </TASK>

Reported-by: syzkaller <syzkaller@googlegroups.com>
Reported-by: Yue Sun <samsun1006219@gmail.com>
Reported-by: xingwei lee <xrivendell7@gmail.com>
Closes: https://lore.kernel.org/netdev/CAEkJfYNJM=cw-8x7_Vmj1J6uYVCWMbbvD=EFmDPVBGpTsqOxEA@mail.gmail.com/
Fixes: e3118e83

 ("net: tcp: add DCTCP congestion control algorithm")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240517091626.32772-1-kuniyu@amazon.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Test arp_ndisc_untracked_subnets use tcpdump to filter the unsolicited
and untracked na messages. It set -e before calling tcpdump. But if
tcpdump filters 0 packet, it will return none zero, and cause the script
to exit.

Instead of using slow tcpdump to capture packets, let's using tc rule
to filter out the na message.

At the same time, fix function setup_v6 which only needs one parameter.
Move all the related helpers from forwarding lib.sh to net lib.sh.

Fixes: 0ea7b0a4

 ("selftests: net: arp_ndisc_untracked_subnets: test for arp_accept and accept_untracked_na")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240517010327.2631319-1-liuhangbin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

seg6_hmac_init_algo returns without cleaning up the previous allocations
if one fails, so it's going to leak all that memory and the crypto tfms.

Update seg6_hmac_exit to only free the memory when allocated, so we can
reuse the code directly.

Fixes: bf355b8d

 ("ipv6: sr: add core files for SR HMAC support")
Reported-by: Sabrina Dubroca <sd@queasysnail.net>
Closes: https://lore.kernel.org/netdev/Zj3bh-gE7eT6V6aH@hog/
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://lore.kernel.org/r/20240517005435.2600277-1-liuhangbin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Billy Jheng Bing-Jhong reported a race between __unix_gc() and
queue_oob().

__unix_gc() tries to garbage-collect close()d inflight sockets,
and then if the socket has MSG_OOB in unix_sk(sk)->oob_skb, GC
will drop the reference and set NULL to it locklessly.

However, the peer socket still can send MSG_OOB message and
queue_oob() can update unix_sk(sk)->oob_skb concurrently, leading
NULL pointer dereference. [0]

To fix the issue, let's update unix_sk(sk)->oob_skb under the
sk_receive_queue's lock and take it everywhere we touch oob_skb.

Note that we defer kfree_skb() in manage_oob() to silence lockdep
false-positive (See [1]).

[0]:
BUG: kernel NULL pointer dereference, address: 0000000000000008
 PF: supervisor write access in kernel mode
 PF: error_code(0x0002) - not-present page
PGD 8000000009f5e067 P4D 8000000009f5e067 PUD 9f5d067 PMD 0
Oops: 0002 [#1] PREEMPT SMP PTI
CPU: 3 PID: 50 Comm: kworker/3:1 Not tainted 6.9.0-rc5-00191-gd091e579b864 #110
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014
Workqueue: events delayed_fput
RIP: 0010:skb_dequeue (./include/linux/skbuff.h:2386 ./include/linux/skbuff.h:2402 net/core/skbuff.c:3847)
Code: 39 e3 74 3e 8b 43 10 48 89 ef 83 e8 01 89 43 10 49 8b 44 24 08 49 c7 44 24 08 00 00 00 00 49 8b 14 24 49 c7 04 24 00 00 00 00 <48> 89 42 08 48 89 10 e8 e7 c5 42 00 4c 89 e0 5b 5d 41 5c c3 cc cc
RSP: 0018:ffffc900001bfd48 EFLAGS: 00000002
RAX: 0000000000000000 RBX: ffff8880088f5ae8 RCX: 00000000361289f9
RDX: 0000000000000000 RSI: 0000000000000206 RDI: ffff8880088f5b00
RBP: ffff8880088f5b00 R08: 0000000000080000 R09: 0000000000000001
R10: 0000000000000003 R11: 0000000000000001 R12: ffff8880056b6a00
R13: ffff8880088f5280 R14: 0000000000000001 R15: ffff8880088f5a80
FS:  0000000000000000(0000) GS:ffff88807dd80000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000008 CR3: 0000000006314000 CR4: 00000000007506f0
PKRU: 55555554
Call Trace:
 <TASK>
 unix_release_sock (net/unix/af_unix.c:654)
 unix_release (net/unix/af_unix.c:1050)
 __sock_release (net/socket.c:660)
 sock_close (net/socket.c:1423)
 __fput (fs/file_table.c:423)
 delayed_fput (fs/file_table.c:444 (discriminator 3))
 process_one_work (kernel/workqueue.c:3259)
 worker_thread (kernel/workqueue.c:3329 kernel/workqueue.c:3416)
 kthread (kernel/kthread.c:388)
 ret_from_fork (arch/x86/kernel/process.c:153)
 ret_from_fork_asm (arch/x86/entry/entry_64.S:257)
 </TASK>
Modules linked in:
CR2: 0000000000000008

Link: https://lore.kernel.org/netdev/a00d3993-c461-43f2-be6d-07259c98509a@rbox.co/ [1]
Fixes: 1279f9d9

 ("af_unix: Call kfree_skb() for dead unix_(sk)->oob_skb in GC.")
Reported-by: Billy Jheng Bing-Jhong <billy@starlabs.sg>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20240516134835.8332-1-kuniyu@amazon.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

This reverts commit 7274c414.

Ken reported that RTL8125b can lock up if gro_flush_timeout has the
default value of 20000 and napi_defer_hard_irqs is set to 0.
In this scenario device interrupts aren't disabled, what seems to
trigger some silicon bug under heavy load. I was able to reproduce this
behavior on RTL8168h. Fix this by reverting 7274c414.

Fixes: 7274c414

 ("r8169: don't try to disable interrupts if NAPI is scheduled already")
Cc: stable@vger.kernel.org
Reported-by: Ken Milmore <ken.milmore@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/9b5b6f4c-4f54-4b90-b0b3-8d8023c2e780@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

syzbot reported the following uninit-value access issue [1]

nci_rx_work() parses received packet from ndev->rx_q. It should be
validated header size, payload size and total packet size before
processing the packet. If an invalid packet is detected, it should be
silently discarded.

Fixes: d24b0353

 ("nfc: nci: Fix uninit-value in nci_dev_up and nci_ntf_packet")
Reported-and-tested-by:  <syzbot+d7b4dc6cd50410152534@syzkaller.appspotmail.com>
Closes: https://syzkaller.appspot.com/bug?extid=d7b4dc6cd50410152534 [1]
Signed-off-by: Ryosuke Yasuoka <ryasuoka@redhat.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The amt.sh requires smcrouted for multicasting routing.
So, it starts smcrouted before forwarding tests.
It must be stopped after all tests, but it isn't.

To fix this issue, it kills smcrouted in the cleanup logic.

Fixes: c08e8bae

 ("selftests: add amt interface selftest script")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The seg6_input() function is responsible for adding the SRH into a
packet, delegating the operation to the seg6_input_core(). This function
uses the skb_cow_head() to ensure that there is sufficient headroom in
the sk_buff for accommodating the link-layer header.
In the event that the skb_cow_header() function fails, the
seg6_input_core() catches the error but it does not release the sk_buff,
which will result in a memory leak.

This issue was introduced in commit af3b5158 ("ipv6: sr: fix BUG due
to headroom too small after SRH push") and persists even after commit
7a3f5b0d ("netfilter: add netfilter hooks to SRv6 data plane"),
where the entire seg6_input() code was refactored to deal with netfilter
hooks.

The proposed patch addresses the identified memory leak by requiring the
seg6_input_core() function to release the sk_buff in the event that
skb_cow_head() fails.

Fixes: af3b5158

 ("ipv6: sr: fix BUG due to headroom too small after SRH push")
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Stephen reported that he was unable to get the dsa_loop driver to get
probed, and the reason ended up being because he had CONFIG_FIXED_PHY=y
in his kernel configuration. As Masahiro explained it:

  "obj-m += dsa/" means everything under dsa/ must be modular.

  If there is a built-in object under dsa/ with CONFIG_NET_DSA=m,
  you cannot do  "obj-$(CONFIG_NET_DSA) += dsa/".

  You need to change it back to "obj-y += dsa/".

This was the case here whereby CONFIG_NET_DSA=m, and so the
obj-$(CONFIG_FIXED_PHY) += dsa_loop_bdinfo.o rule is not executed and
the DSA loop mdio_board info structure is not registered with the
kernel, and eventually the device is simply not found.

To preserve the intention of the original commit of limiting the amount
of folder descending, conditionally descend into drivers/net/dsa when
CONFIG_NET_DSA is enabled.

Fixes: 227d7206

 ("dsa: simplify Kconfig symbols and dependencies")
Reported-by: Stephen Langstaff <stephenlangstaff1@gmail.com>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 1a7d0890 ("kprobe/ftrace: bail out if ftrace was killed")
introduced a bad K&R function definition, which we haven't accepted in a
long long time.

Gcc seems to let it slide, but clang notices with the appropriate error:

  kernel/kprobes.c:1140:24: error: a function declaration without a prototype is deprecated in all >
   1140 | void kprobe_ftrace_kill()
        |                        ^
        |                         void

but this commit was apparently never in linux-next before it was sent
upstream, so it didn't get the appropriate build test coverage.

Fixes: 1a7d0890

 kprobe/ftrace: bail out if ftrace was killed
Cc: Stephen Brennan <stephen.s.brennan@oracle.com>
Cc: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Cc: Guo Ren <guoren@kernel.org>
Cc: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull networking fixes from Jakub Kicinski:
 "Current release - regressions:

   - virtio_net: fix missed error path rtnl_unlock after control queue
     locking rework

  Current release - new code bugs:

   - bpf: fix KASAN slab-out-of-bounds in percpu_array_map_gen_lookup,
     caused by missing nested map handling

   - drv: dsa: correct initialization order for KSZ88x3 ports

  Previous releases - regressions:

   - af_packet: do not call packet_read_pending() from
     tpacket_destruct_skb() fix performance regression

   - ipv6: fix route deleting failure when metric equals 0, don't assume
     0 means not set / default in this case

  Previous releases - always broken:

   - bridge: couple of syzbot-driven fixes"

* tag 'net-6.10-rc0' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (30 commits)
  selftests: net: local_termination: annotate the expected failures
  net: dsa: microchip: Correct initialization order for KSZ88x3 ports
  MAINTAINERS: net: Update reviewers for TI's Ethernet drivers
  dt-bindings: net: ti: Update maintainers list
  l2tp: fix ICMP error handling for UDP-encap sockets
  net: txgbe: fix to control VLAN strip
  net: wangxun: match VLAN CTAG and STAG features
  net: wangxun: fix to change Rx features
  af_packet: do not call packet_read_pending() from tpacket_destruct_skb()
  virtio_net: Fix missed rtnl_unlock
  netrom: fix possible dead-lock in nr_rt_ioctl()
  idpf: don't skip over ethtool tcp-data-split setting
  dt-bindings: net: qcom: ethernet: Allow dma-coherent
  bonding: fix oops during rmmod
  net/ipv6: Fix route deleting failure when metric equals 0
  selftests/net: reduce xfrm_policy test time
  selftests/bpf: Adjust btf_dump test to reflect recent change in file_operations
  selftests/bpf: Adjust test_access_variable_array after a kernel function name change
  selftests/net/lib: no need to record ns name if it already exist
  net: qrtr: ns: Fix module refcnt
  ...

Pull tracing tool updates from Steven Rostedt:
 "Specific for timerlat:

   - Improve the output of timerlat top by adding a missing \n, and by
     avoiding printing color-formatting characters where they are
     translated to regular characters.

   - Improve timerlat auto-analysis output by replacing '\t' with spaces
     to avoid copy-and-paste issues when reporting problems.

   - Make the user-space (-u) option the default, as it is the most
     complete test. Add a -k option to use the in-kernel workload.

   - On timerlat top and hist, add a summary with the overall results.
     For instance, the minimum value for all CPUs, the overall average
     and the maximum value from all CPUs.

   - timerlat hist was printing initial values (i.e., 0 as max, and ~0
     as min) if the trace stopped before the first Ret-User event. This
     problem was fixed by printing the " - " no value string to the
     output if that was the case.

  For all RTLA tools:

   - Add a --warm-up <seconds> option, allowing the workload to run for
     <seconds> before starting to collect results.

   - Add a --trace-buffer-size option, allowing the user to set the
     tracing buffer size for -t option. This option is mainly useful for
     reducing the trace file. Now rtla depends on libtracefs >= 1.6.

   - Fix the -t [trace_file] parsing, now it does not require the '='
     before the option parameter, and better handles the multiple ways a
     user can pass the trace_file.txt"

* tag 'trace-tools-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
  rtla: Documentation: Fix -t, --trace
  rtla: Fix -t\--trace[=file]
  rtla/timerlat: Fix histogram report when a cpu count is 0
  rtla: Add --trace-buffer-size option
  rtla/timerlat: Make user-space threads the default
  rtla: Add the --warm-up option
  rtla/timerlat: Add a summary for hist mode
  rtla/timerlat: Add a summary for top mode
  rtla/timerlat: Use pretty formatting only on interactive tty
  rtla/auto-analysis: Replace \t with spaces
  rtla/timerlat: Simplify "no value" printing on top

Merge tag 'trace-user-events-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace

Pull tracing user-event updates from Steven Rostedt:

 - Minor update to the user_events interface

  The ABI of creating a user event states that the fields are separated
  by semicolons, and spaces should be ignored.

  But the parsing expected at least one space to be there (which was
  incorrect). Fix the reading of the string to handle fields separated
  by semicolons but no space between them.

  This does extend the API sightly as now "field;field" will now be
  parsed and not cause an error. But it should not cause any regressions
  as no logic should expect it to fail.

  Note, that the logic that parses the event fields to create the
  trace_event works with no spaces after the semi-colon. It is
  the logic that tests against existing events that is inconsistent.
  This causes registering an event without using spaces to succeed
  if it doesn't exist, but makes the same call that tries to register
  to the same event, but doesn't use spaces, fail.

* tag 'trace-user-events-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
  selftests/user_events: Add non-spacing separator check
  tracing/user_events: Fix non-spaced field matching

Merge tag 'trace-ringbuffer-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace

Pull tracing ring buffer updates from Steven Rostedt:
 "Add ring_buffer memory mappings.

  The tracing ring buffer was created based on being mostly used with
  the splice system call. It is broken up into page ordered sub-buffers
  and the reader swaps a new sub-buffer with an existing sub-buffer
  that's part of the write buffer. It then has total access to the
  swapped out sub-buffer and can do copyless movements of the memory
  into other mediums (file system, network, etc).

  The buffer is great for passing around the ring buffer contents in the
  kernel, but is not so good for when the consumer is the user space
  task itself.

  A new interface is added that allows user space to memory map the ring
  buffer. It will get all the write sub-buffers as well as reader
  sub-buffer (that is not written to). It can send an ioctl to change
  which sub-buffer is the new reader sub-buffer.

  The ring buffer is read only to user space. It only needs to call the
  ioctl when it is finished with a sub-buffer and needs a new sub-buffer
  that the writer will not write over.

  A self test program was also created for testing and can be used as an
  example for the interface to user space. The libtracefs (external to
  the kernel) also has code that interacts with this, although it is
  disabled until the interface is in a official release. It can be
  enabled by compiling the library with a special flag. This was used
  for testing applications that perform better with the buffer being
  mapped.

  Memory mapped buffers have limitations. The main one is that it can
  not be used with the snapshot logic. If the buffer is mapped,
  snapshots will be disabled. If any logic is set to trigger snapshots
  on a buffer, that buffer will not be allowed to be mapped"

* tag 'trace-ringbuffer-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
  ring-buffer: Add cast to unsigned long addr passed to virt_to_page()
  ring-buffer: Have mmapped ring buffer keep track of missed events
  ring-buffer/selftest: Add ring-buffer mapping test
  Documentation: tracing: Add ring-buffer mapping
  tracing: Allow user-space mapping of the ring-buffer
  ring-buffer: Introducing ring-buffer mapping functions
  ring-buffer: Allocate sub-buffers with __GFP_COMP

Pull tracing updates from Steven Rostedt:

 - Remove unused ftrace_direct_funcs variables

 - Fix a possible NULL pointer dereference race in eventfs

 - Update do_div() usage in trace event benchmark test

 - Speedup direct function registration with asynchronous RCU callback.

   The synchronization was done in the registration code and this caused
   delays when registering direct callbacks. Move the freeing to a
   call_rcu() that will prevent delaying of the registering.

 - Replace simple_strtoul() usage with kstrtoul()

* tag 'trace-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
  eventfs: Fix a possible null pointer dereference in eventfs_find_events()
  ftrace: Fix possible use-after-free issue in ftrace_location()
  ftrace: Remove unused global 'ftrace_direct_func_count'
  ftrace: Remove unused list 'ftrace_direct_funcs'
  tracing: Improve benchmark test performance by using do_div()
  ftrace: Use asynchronous grace period for register_ftrace_direct()
  ftrace: Replaces simple_strtoul in ftrace

Pull probes updates from Masami Hiramatsu:

 - tracing/probes: Add new pseudo-types %pd and %pD support for dumping
   dentry name from 'struct dentry *' and file name from 'struct file *'

 - uprobes performance optimizations:
    - Speed up the BPF uprobe event by delaying the fetching of the
      uprobe event arguments that are not used in BPF
    - Avoid locking by speculatively checking whether uprobe event is
      valid
    - Reduce lock contention by using read/write_lock instead of
      spinlock for uprobe list operation. This improved BPF uprobe
      benchmark result 43% on average

 - rethook: Remove non-fatal warning messages when tracing stack from
   BPF and skip rcu_is_watching() validation in rethook if possible

 - objpool: Optimize objpool (which is used by kretprobes and fprobe as
   rethook backend storage) by inlining functions and avoid caching
   nr_cpu_ids because it is a const value

 - fprobe: Add entry/exit callbacks types (code cleanup)

 - kprobes: Check ftrace was killed in kprobes if it uses ftrace

* tag 'probes-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
  kprobe/ftrace: bail out if ftrace was killed
  selftests/ftrace: Fix required features for VFS type test case
  objpool: cache nr_possible_cpus() and avoid caching nr_cpu_ids
  objpool: enable inlining objpool_push() and objpool_pop() operations
  rethook: honor CONFIG_FTRACE_VALIDATE_RCU_IS_WATCHING in rethook_try_get()
  ftrace: make extra rcu_is_watching() validation check optional
  uprobes: reduce contention on uprobes_tree access
  rethook: Remove warning messages printed for finding return address of a frame.
  fprobe: Add entry/exit callbacks types
  selftests/ftrace: add fprobe test cases for VFS type "%pd" and "%pD"
  selftests/ftrace: add kprobe test cases for VFS type "%pd" and "%pD"
  Documentation: tracing: add new type '%pd' and '%pD' for kprobe
  tracing/probes: support '%pD' type for print struct file's name
  tracing/probes: support '%pd' type for print struct dentry's name
  uprobes: add speculative lockless system-wide uprobe filter check
  uprobes: prepare uprobe args buffer lazily
  uprobes: encapsulate preparation of uprobe args buffer

Pull bootconfig updates from Masami Hiramatsu:

 - Do not put unneeded quotes on the extra command line items which was
   inserted from the bootconfig.

 - Remove redundant spaces from the extra command line.

* tag 'bootconfig-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
  init/main.c: Minor cleanup for the setup_command_line() function
  init/main.c: Remove redundant space from saved_command_line
  bootconfig: do not put quotes on cmdline items unless necessary

Pull sysctl updates from Joel Granados:

 - Remove sentinel elements from ctl_table structs in kernel/*

   Removing sentinels in ctl_table arrays reduces the build time size
   and runtime memory consumed by ~64 bytes per array. Removals for
   net/, io_uring/, mm/, ipc/ and security/ are set to go into mainline
   through their respective subsystems making the next release the most
   likely place where the final series that removes the check for
   proc_name == NULL will land.

   This adds to removals already in arch/, drivers/ and fs/.

 - Adjust ctl_table definitions and references to allow constification
     - Remove unused ctl_table function arguments
     - Move non-const elements from ctl_table to ctl_table_header
     - Make ctl_table pointers const in ctl_table_root structure

   Making the static ctl_table structs const will increase safety by
   keeping the pointers to proc_handler functions in .rodata. Though no
   ctl_tables where made const in this PR, the ground work for making
   that possible has started with these changes sent by Thomas
   Weißschuh.

* tag 'sysctl-6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/sysctl/sysctl:
  sysctl: drop now unnecessary out-of-bounds check
  sysctl: move sysctl type to ctl_table_header
  sysctl: drop sysctl_is_perm_empty_ctl_table
  sysctl: treewide: constify argument ctl_table_root::permissions(table)
  sysctl: treewide: drop unused argument ctl_table_root::set_ownership(table)
  bpf: Remove the now superfluous sentinel elements from ctl_table array
  delayacct: Remove the now superfluous sentinel elements from ctl_table array
  kprobes: Remove the now superfluous sentinel elements from ctl_table array
  printk: Remove the now superfluous sentinel elements from ctl_table array
  scheduler: Remove the now superfluous sentinel elements from ctl_table array
  seccomp: Remove the now superfluous sentinel elements from ctl_table array
  timekeeping: Remove the now superfluous sentinel elements from ctl_table array
  ftrace: Remove the now superfluous sentinel elements from ctl_table array
  umh: Remove the now superfluous sentinel elements from ctl_table array
  kernel misc: Remove the now superfluous sentinel elements from ctl_table array

Pull devicetree updates from Rob Herring:
 "DT Bindings:

   - Convert samsung,exynos5-dp, atmel,lcdc, aspeed,ast2400-wdt bindings
     to schemas

   - Add bindings for Allwinner H616 NMI controller, Renesas r8a779g0
     irqc, Renesas R-Car V4M TMU and CMT timers, Freescale S32G3
     linflexuart, and Mediatek MT7988 XHCI

   - Add 'reg' constraints on DSI and SPI display panels

   - More dropping of unnecessary quotes in schemas

   - Use full paths rather than relative paths in schema $refs

   - Drop redundant storing of phandle for reserved memory

  DT Core:

   - Use scope based cleanups for kfree() and of_node_put()

   - Track interrupt-map and power-supplies for fw_devlink

   - Add buffer overflow check in of_modalias()

   - Add and use __of_prop_free() helper for freeing struct property"

* tag 'devicetree-for-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (25 commits)
  of: property: Add fw_devlink support for interrupt-map property
  dt-bindings: display: panel: constrain 'reg' in DSI panels
  dt-bindings: display: panel: constrain 'reg' in SPI panels
  dt-bindings: display: samsung,ams495qa01: add missing SPI properties ref
  dt-bindings: Use full path to other schemas
  dt-bindings: PCI: qcom,pcie-sm8350: Drop redundant 'oneOf' sub-schema
  of: module: add buffer overflow check in of_modalias()
  dt-bindings: PCI: microchip: increase number of items in ranges property
  dt-bindings: Drop unnecessary quotes on keys
  dt-bindings: interrupt-controller: mediatek,mt6577-sysirq: Drop unnecessary quotes
  of: property: Use scope based cleanup on port_node
  of: reserved_mem: Remove the use of phandle from the reserved_mem APIs
  of: property: fw_devlink: Add support for "power-supplies" binding
  dt-bindings: watchdog: aspeed,ast2400-wdt: Convert to DT schema
  dt-bindings: irq: sun7i-nmi: Add binding for the H616 NMI controller
  dt-bindings: interrupt-controller: renesas,irqc: Add r8a779g0 support
  dt-bindings: timer: renesas,tmu: Add R-Car V4M support
  dt-bindings: timer: renesas,cmt: Add R-Car V4M support
  of: Use scope based of_node_put() cleanups
  of: Use scope based kfree() cleanups
  ...

Vladimir said when adding this test:

  The bridge driver fares particularly badly [...] mainly because
  it does not implement IFF_UNICAST_FLT.

See commit 90b9566a

 ("selftests: forwarding: add a test for
local_termination.sh").

We don't want to hide the known gaps, but having a test which
always fails prevents us from catching regressions. Report
the cases we know may fail as XFAIL.

Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Link: https://lore.kernel.org/r/20240516152513.1115270-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Adjust the initialization sequence of KSZ88x3 switches to enable
802.1p priority control on Port 2 before configuring Port 1. This
change ensures the apptrust functionality on Port 1 operates
correctly, as it depends on the priority settings of Port 2. The
prior initialization sequence incorrectly configured Port 1 first,
which could lead to functional discrepancies.

Fixes: a1ea5771

 ("net: dsa: microchip: dcb: add special handling for KSZ88X3 family")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Hariprasad Kelam <hkelam@marvell.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://lore.kernel.org/r/20240517050121.2174412-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Remove myself as reviewer for TI's ethernet drivers

Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240516082545.6412-1-r-gunasekaran@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Update the list with the current maintainers of TI's CPSW ethernet
peripheral.

Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20240516054932.27597-1-r-gunasekaran@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Since commit a36e185e
("udp: Handle ICMP errors for tunnels with same destination port on both endpoints")
UDP's handling of ICMP errors has allowed for UDP-encap tunnels to
determine socket associations in scenarios where the UDP hash lookup
could not.

Subsequently, commit d26796ae
("udp: check udp sock encap_type in __udp_lib_err")
subtly tweaked the approach such that UDP ICMP error handling would be
skipped for any UDP socket which has encapsulation enabled.

In the case of L2TP tunnel sockets using UDP-encap, this latter
modification effectively broke ICMP error reporting for the L2TP
control plane.

To a degree this isn't catastrophic inasmuch as the L2TP control
protocol defines a reliable transport on top of the underlying packet
switching network which will eventually detect errors and time out.

However, paying attention to the ICMP error reporting allows for more
timely detection of errors in L2TP userspace, and aids in debugging
connectivity issues.

Reinstate ICMP error handling for UDP encap L2TP tunnels:

 * implement struct udp_tunnel_sock_cfg .encap_err_rcv in order to allow
   the L2TP code to handle ICMP errors;

 * only implement error-handling for tunnels which have a managed
   socket: unmanaged tunnels using a kernel socket have no userspace to
   report errors back to;

 * flag the error on the socket, which allows for userspace to get an
   error such as -ECONNREFUSED back from sendmsg/recvmsg;

 * pass the error into ip[v6]_icmp_error() which allows for userspace to
   get extended error information via. MSG_ERRQUEUE.

Fixes: d26796ae

 ("udp: check udp sock encap_type in __udp_lib_err")
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Link: https://lore.kernel.org/r/20240513172248.623261-1-tparkin@katalix.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Pull parisc updates from Helge Deller:

 -  define sigset_t in parisc uapi header to fix build of util-linux

 -  define HAVE_ARCH_HUGETLB_UNMAPPED_AREA to avoid compiler warning

 -  drop unused 'exc_reg' struct in math-emu code

* tag 'parisc-for-6.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Define HAVE_ARCH_HUGETLB_UNMAPPED_AREA
  parisc/math-emu: Remove unused struct 'exc_reg'
  parisc: Define sigset_t in parisc uapi header

Pull powerpc updates from Michael Ellerman:

 - Enable BPF Kernel Functions (kfuncs) in the powerpc BPF JIT.

 - Allow per-process DEXCR (Dynamic Execution Control Register) settings
   via prctl, notably NPHIE which controls hashst/hashchk for ROP
   protection.

 - Install powerpc selftests in sub-directories. Note this changes the
   way run_kselftest.sh needs to be invoked for powerpc selftests.

 - Change fadump (Firmware Assisted Dump) to better handle memory
   add/remove.

 - Add support for passing additional parameters to the fadump kernel.

 - Add support for updating the kdump image on CPU/memory add/remove
   events.

 - Other small features, cleanups and fixes.

Thanks to Andrew Donnellan, Andy Shevchenko, Aneesh Kumar K.V, Arnd
Bergmann, Benjamin Gray, Bjorn Helgaas, Christian Zigotzky, Christophe
Jaillet, Christophe Leroy, Colin Ian King, Cédric Le Goater, Dr. David
Alan Gilbert, Erhard Furtner, Frank Li, GUO Zihua, Ganesh Goudar, Geoff
Levand, Ghanshyam Agrawal, Greg Kurz, Hari Bathini, Joel Stanley, Justin
Stitt, Kunwu Chan, Li Yang, Lidong Zhong, Madhavan Srinivasan, Mahesh
Salgaonkar, Masahiro Yamada, Matthias Schiffer, Naresh Kamboju, Nathan
Chancellor, Nathan Lynch, Naveen N Rao, Nicholas Miehlbradt, Ran Wang,
Randy Dunlap, Ritesh Harjani, Sachin Sant, Shirisha Ganta, Shrikanth
Hegde, Sourabh Jain, Stephen Rothwell, sundar, Thorsten Blum, Vaibhav
Jain, Xiaowei Bao, Yang Li, and Zhao Chenhui.

* tag 'powerpc-6.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (85 commits)
  powerpc/fadump: Fix section mismatch warning
  powerpc/85xx: fix compile error without CONFIG_CRASH_DUMP
  powerpc/fadump: update documentation about bootargs_append
  powerpc/fadump: pass additional parameters when fadump is active
  powerpc/fadump: setup additional parameters for dump capture kernel
  powerpc/pseries/fadump: add support for multiple boot memory regions
  selftests/powerpc/dexcr: Fix spelling mistake "predicition" -> "prediction"
  KVM: PPC: Book3S HV nestedv2: Fix an error handling path in gs_msg_ops_kvmhv_nestedv2_config_fill_info()
  KVM: PPC: Fix documentation for ppc mmu caps
  KVM: PPC: code cleanup for kvmppc_book3s_irqprio_deliver
  KVM: PPC: Book3S HV nestedv2: Cancel pending DEC exception
  powerpc/xmon: Check cpu id in commands "c#", "dp#" and "dx#"
  powerpc/code-patching: Use dedicated memory routines for patching
  powerpc/code-patching: Test patch_instructions() during boot
  powerpc64/kasan: Pass virtual addresses to kasan_init_phys_region()
  powerpc: rename SPRN_HID2 define to SPRN_HID2_750FX
  powerpc: Fix typos
  powerpc/eeh: Fix spelling of the word "auxillary" and update comment
  macintosh/ams: Fix unused variable warning
  powerpc/Makefile: Remove bits related to the previous use of -mcmodel=large
  ...

Pull ARM updates from Russell King:

 - Updates to AMBA bus subsystem to drop .owner struct device_driver
   initialisations, moving that to code instead.

 - Add LPAE privileged-access-never support

 - Add support for Clang CFI

 - clkdev: report over-sized device or connection strings

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rmk/linux: (36 commits)
  ARM: 9398/1: Fix userspace enter on LPAE with CC_OPTIMIZE_FOR_SIZE=y
  clkdev: report over-sized strings when creating clkdev entries
  ARM: 9393/1: mm: Use conditionals for CFI branches
  ARM: 9392/2: Support CLANG CFI
  ARM: 9391/2: hw_breakpoint: Handle CFI breakpoints
  ARM: 9390/2: lib: Annotate loop delay instructions for CFI
  ARM: 9389/2: mm: Define prototypes for all per-processor calls
  ARM: 9388/2: mm: Type-annotate all per-processor assembly routines
  ARM: 9387/2: mm: Rewrite cacheflush vtables in CFI safe C
  ARM: 9386/2: mm: Use symbol alias for cache functions
  ARM: 9385/2: mm: Type-annotate all cache assembly routines
  ARM: 9384/2: mm: Make tlbflush routines CFI safe
  ARM: 9382/1: ftrace: Define ftrace_stub_graph
  ARM: 9358/2: Implement PAN for LPAE by TTBR0 page table walks disablement
  ARM: 9357/2: Reduce the number of #ifdef CONFIG_CPU_SW_DOMAIN_PAN
  ARM: 9356/2: Move asm statements accessing TTBCR into C functions
  ARM: 9355/2: Add TTBCR_* definitions to pgtable-3level-hwdef.h
  ARM: 9379/1: coresight: tpda: drop owner assignment
  ARM: 9378/1: coresight: etm4x: drop owner assignment
  ARM: 9377/1: hwrng: nomadik: drop owner assignment
  ...

Jiawen Wu says:

====================
Wangxun fixes

Fixed some bugs when using ethtool to operate network devices.

v4 -> v5:
- Simplify if...else... to fix features.

v3 -> v4:
- Require both ctag and stag to be enabled or disabled.

v2 -> v3:
- Drop the first patch.

v1 -> v2:
- Factor out the same code.
- Remove statistics printing with more than 64 queues.
- Detail the commit logs to describe issues.
- Remove reset flag check in wx_update_stats().
- Change to set VLAN CTAG and STAG to be consistent.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

When VLAN tag strip is changed to enable or disable, the hardware requires
the Rx ring to be in a disabled state, otherwise the feature cannot be
changed.

Fixes: f3b03c65

 ("net: wangxun: Implement vlan add and kill functions")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hardware requires VLAN CTAG and STAG configuration always matches. And
whether VLAN CTAG or STAG changes, the configuration needs to be changed
as well.

Fixes: 6670f1ec

 ("net: txgbe: Add netdev features support")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Sai Krishna <saikrishnag@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the issue where some Rx features cannot be changed.

When using ethtool -K to turn off rx offload, it returns error and
displays "Could not change any device features". And netdev->features
is not assigned a new value to actually configure the hardware.

Fixes: 6dbedcff

 ("net: libwx: Implement xx_set_features ops")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

trafgen performance considerably sank on hosts with many cores
after the blamed commit.

packet_read_pending() is very expensive, and calling it
in af_packet fast path defeats Daniel intent in commit
b0138408 ("packet: use percpu mmap tx frame pending refcount")

tpacket_destruct_skb() makes room for one packet, we can immediately
wakeup a producer, no need to completely drain the tx ring.

Fixes: 89ed5b51

 ("af_packet: Block execution of tasks waiting for transmit to complete in AF_PACKET")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20240515163358.4105915-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>