- Dec 01, 2021
-
-
Vladimir Oltean authored
[ Upstream commit c49a35ee ] The driver doesn't support RX timestamping for non-PTP packets, but it declares that it does. Restrict the reported RX filters to PTP v2 over L2 and over L4. Fixes: 4e3b0468 ("net: mscc: PTP Hardware Clock (PHC) support") Signed-off-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by:
Jakub Kicinski <kuba@kernel.org> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Vladimir Oltean authored
[ Upstream commit 8a075464 ] The ocelot driver, when asked to timestamp all receiving packets, 1588 v1 or NTP, says "nah, here's 1588 v2 for you". According to this discussion: https://patchwork.kernel.org/project/netdevbpf/patch/20211104133204.19757-8-martin.kaistra@linutronix.de/#24577647 drivers that downgrade from a wider request to a narrower response (or even a response where the intersection with the request is empty) are buggy, and should return -ERANGE instead. This patch fixes that. Fixes: 4e3b0468 ("net: mscc: PTP Hardware Clock (PHC) support") Suggested-by:
Richard Cochran <richardcochran@gmail.com> Signed-off-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Acked-by:
Richard Cochran <richardcochran@gmail.com> Signed-off-by:
Jakub Kicinski <kuba@kernel.org> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Jie Wang authored
[ Upstream commit 82229c4d ] Currently, HNS3 driver doesn't clear the reset flags of components after successfully executing reset, it causes userspace info of "Components reset" and "Components not reset" is incorrect. So fix this problem by clear corresponding reset flag after reset process. Fixes: ddccc5e3 ("net: hns3: add support for triggering reset by ethtool") Signed-off-by:
Jie Wang <wangjie125@huawei.com> Signed-off-by:
Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by:
Jakub Kicinski <kuba@kernel.org> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Guangbin Huang authored
[ Upstream commit 8d2ad993 ] When PF is set to multi-TCs and configured mapping relationship between priorities and TCs, the hardware will active these settings for this PF and its VFs. In this case when VF just uses one TC and its rx packets contain priority, and if the priority is not mapped to TC0, as other TCs of VF is not valid, hardware always put this kind of packets to the queue 0. It cause this kind of packets of VF can not be used RSS function. To fix this problem, set tc mode of all unused TCs of VF to the setting of TC0, then rx packet with priority which map to unused TC will be direct to TC0. Fixes: e2cb1dec ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support") Signed-off-by:
Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by:
Jakub Kicinski <kuba@kernel.org> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Tony Lu authored
[ Upstream commit bacb6c1e ] When applications call shutdown() with SHUT_RDWR in userspace, smc_close_active() calls kernel_sock_shutdown(), and it is called twice in smc_shutdown(). This fixes this by checking sk_state before do clcsock shutdown, and avoids missing the application's call of smc_shutdown(). Link: https://lore.kernel.org/linux-s390/1f67548e-cbf6-0dce-82b5-10288a4583bd@linux.ibm.com/ Fixes: 606a63c9 ("net/smc: Ensure the active closing peer first closes clcsock") Signed-off-by:
Tony Lu <tonylu@linux.alibaba.com> Reviewed-by:
Wen Gu <guwen@linux.alibaba.com> Acked-by:
Karsten Graul <kgraul@linux.ibm.com> Link: https://lore.kernel.org/r/20211126024134.45693-1-tonylu@linux.alibaba.com Signed-off-by:
Jakub Kicinski <kuba@kernel.org> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Ziyang Xuan authored
[ Upstream commit 01d9cc2d ] Inject error before dev_hold(real_dev) in register_vlan_dev(), and execute the following testcase: ip link add dev dummy1 type dummy ip link add name dummy1.100 link dummy1 type vlan id 100 ip link del dev dummy1 When the dummy netdevice is removed, we will get a WARNING as following: ======================================================================= refcount_t: decrement hit 0; leaking memory. WARNING: CPU: 2 PID: 0 at lib/refcount.c:31 refcount_warn_saturate+0xbf/0x1e0 and an endless loop of: ======================================================================= unregister_netdevice: waiting for dummy1 to become free. Usage count = -1073741824 That is because dev_put(real_dev) in vlan_dev_free() be called without dev_hold(real_dev) in register_vlan_dev(). It makes the refcnt of real_dev underflow. Move the dev_hold(real_dev) to vlan_dev_init() which is the call-back of ndo_init(). That makes dev_hold() and dev_put() for vlan's real_dev symmetrical. Fixes: 563bcbae ("net: vlan: fix a UAF in vlan_dev_real_dev()") Reported-by:
Petr Machata <petrm@nvidia.com> Suggested-by:
Jakub Kicinski <kuba@kernel.org> Signed-off-by:
Ziyang Xuan <william.xuanziyang@huawei.com> Link: https://lore.kernel.org/r/20211126015942.2918542-1-william.xuanziyang@huawei.com Signed-off-by:
Jakub Kicinski <kuba@kernel.org> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Julian Wiedmann authored
[ Upstream commit 0276af21 ] ethtool_set_coalesce() now uses both the .get_coalesce() and .set_coalesce() callbacks. But the check for their availability is buggy, so changing the coalesce settings on a device where the driver provides only _one_ of the callbacks results in a NULL pointer dereference instead of an -EOPNOTSUPP. Fix the condition so that the availability of both callbacks is ensured. This also matches the netlink code. Note that reproducing this requires some effort - it only affects the legacy ioctl path, and needs a specific combination of driver options: - have .get_coalesce() and .coalesce_supported but no .set_coalesce(), or - have .set_coalesce() but no .get_coalesce(). Here eg. ethtool doesn't cause the crash as it first attempts to call ethtool_get_coalesce() and bails out on error. Fixes: f3ccfda1 ("ethtool: extend coalesce setting uAPI with CQE mode") Cc: Yufeng Mo <moyufeng@huawei.com> Cc: Huazhong Tan <tanhuazhong@huawei.com> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by:
Julian Wiedmann <jwi@linux.ibm.com> Link: https://lore.kernel.org/r/20211126175543.28000-1-jwi@linux.ibm.com Signed-off-by:
Jakub Kicinski <kuba@kernel.org> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Davide Caratti authored
[ Upstream commit de6d2592 ] when the number of DRR classes decreases, the round-robin active list can contain elements that have already been freed in ets_qdisc_change(). As a consequence, it's possible to see a NULL dereference crash, caused by the attempt to call cl->qdisc->ops->peek(cl->qdisc) when cl->qdisc is NULL: BUG: kernel NULL pointer dereference, address: 0000000000000018 #PF: supervisor read access in kernel mode #PF: error_code(0x0000) - not-present page PGD 0 P4D 0 Oops: 0000 [#1] PREEMPT SMP NOPTI CPU: 1 PID: 910 Comm: mausezahn Not tainted 5.16.0-rc1+ #475 Hardware name: Red Hat KVM, BIOS 1.11.1-4.module+el8.1.0+4066+0f1aadab 04/01/2014 RIP: 0010:ets_qdisc_dequeue+0x129/0x2c0 [sch_ets] Code: c5 01 41 39 ad e4 02 00 00 0f 87 18 ff ff ff 49 8b 85 c0 02 00 00 49 39 c4 0f 84 ba 00 00 00 49 8b ad c0 02 00 00 48 8b 7d 10 <48> 8b 47 18 48 8b 40 38 0f ae e8 ff d0 48 89 c3 48 85 c0 0f 84 9d RSP: 0000:ffffbb36c0b5fdd8 EFLAGS: 00010287 RAX: ffff956678efed30 RBX: 0000000000000000 RCX: 0000000000000000 RDX: 0000000000000002 RSI: ffffffff9b938dc9 RDI: 0000000000000000 RBP: ffff956678efed30 R08: e2f3207fe360129c R09: 0000000000000000 R10: 0000000000000001 R11: 0000000000000001 R12: ffff956678efeac0 R13: ffff956678efe800 R14: ffff956611545000 R15: ffff95667ac8f100 FS: 00007f2aa9120740(0000) GS:ffff95667b800000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000018 CR3: 000000011070c000 CR4: 0000000000350ee0 Call Trace: <TASK> qdisc_peek_dequeued+0x29/0x70 [sch_ets] tbf_dequeue+0x22/0x260 [sch_tbf] __qdisc_run+0x7f/0x630 net_tx_action+0x290/0x4c0 __do_softirq+0xee/0x4f8 irq_exit_rcu+0xf4/0x130 sysvec_apic_timer_interrupt+0x52/0xc0 asm_sysvec_apic_timer_interrupt+0x12/0x20 RIP: 0033:0x7f2aa7fc9ad4 Code: b9 ff ff 48 8b 54 24 18 48 83 c4 08 48 89 ee 48 89 df 5b 5d e9 ed fc ff ff 0f 1f 00 66 2e 0f 1f 84 00 00 00 00 00 f3 0f 1e fa <53> 48 83 ec 10 48 8b 05 10 64 33 00 48 8b 00 48 85 c0 0f 85 84 00 RSP: 002b:00007ffe5d33fab8 EFLAGS: 00000202 RAX: 0000000000000002 RBX: 0000561f72c31460 RCX: 0000561f72c31720 RDX: 0000000000000002 RSI: 0000561f72c31722 RDI: 0000561f72c31720 RBP: 000000000000002a R08: 00007ffe5d33fa40 R09: 0000000000000014 R10: 0000000000000000 R11: 0000000000000246 R12: 0000561f7187e380 R13: 0000000000000000 R14: 0000000000000000 R15: 0000561f72c31460 </TASK> Modules linked in: sch_ets sch_tbf dummy rfkill iTCO_wdt intel_rapl_msr iTCO_vendor_support intel_rapl_common joydev virtio_balloon lpc_ich i2c_i801 i2c_smbus pcspkr ip_tables xfs libcrc32c crct10dif_pclmul crc32_pclmul crc32c_intel ahci libahci ghash_clmulni_intel serio_raw libata virtio_blk virtio_console virtio_net net_failover failover sunrpc dm_mirror dm_region_hash dm_log dm_mod CR2: 0000000000000018 Ensuring that 'alist' was never zeroed [1] was not sufficient, we need to remove from the active list those elements that are no more SP nor DRR. [1] https://lore.kernel.org/netdev/60d274838bf09777f0371253416e8af71360bc08.1633609148.git.dcaratti@redhat.com/ v3: fix race between ets_qdisc_change() and ets_qdisc_dequeue() delisting DRR classes beyond 'nbands' in ets_qdisc_change() with the qdisc lock acquired, thanks to Cong Wang. v2: when a NULL qdisc is found in the DRR active list, try to dequeue skb from the next list item. Reported-by:
Hangbin Liu <liuhangbin@gmail.com> Fixes: dcc68b4d ("net: sch_ets: Add a new Qdisc") Signed-off-by:
Davide Caratti <dcaratti@redhat.com> Link: https://lore.kernel.org/r/7a5c496eed2d62241620bdbb83eb03fb9d571c99.1637762721.git.dcaratti@redhat.com Signed-off-by:
Jakub Kicinski <kuba@kernel.org> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Yannick Vignon authored
[ Upstream commit b270bfe6 ] The Tx queues were not disabled in situations where the driver needed to stop the interface to apply a new configuration. This could result in a kernel panic when doing any of the 3 following actions: * reconfiguring the number of queues (ethtool -L) * reconfiguring the size of the ring buffers (ethtool -G) * installing/removing an XDP program (ip l set dev ethX xdp) Prevent the panic by making sure netif_tx_disable is called when stopping an interface. Without this patch, the following kernel panic can be observed when doing any of the actions above: Unable to handle kernel paging request at virtual address ffff80001238d040 [....] Call trace: dwmac4_set_addr+0x8/0x10 dev_hard_start_xmit+0xe4/0x1ac sch_direct_xmit+0xe8/0x39c __dev_queue_xmit+0x3ec/0xaf0 dev_queue_xmit+0x14/0x20 [...] [ end trace 0000000000000002 ]--- Fixes: 5fabb012 ("net: stmmac: Add initial XDP support") Fixes: aa042f60 ("net: stmmac: Add support to Ethtool get/set ring parameters") Fixes: 0366f7e0 ("net: stmmac: add ethtool support for get/set channels") Signed-off-by:
Yannick Vignon <yannick.vignon@nxp.com> Link: https://lore.kernel.org/r/20211124154731.1676949-1-yannick.vignon@oss.nxp.com Signed-off-by:
Jakub Kicinski <kuba@kernel.org> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Jakub Kicinski authored
[ Upstream commit f3911f73 ] We replace proto_ops whenever TLS is configured for RX. But our replacement also overrides sendpage_locked, which will crash unless TX is also configured. Similarly we plug both of those in for TLS_HW (NIC crypto offload) even tho TLS_HW has a completely different implementation for TX. Last but not least we always plug in something based on inet_stream_ops even though a few of the callbacks differ for IPv6 (getname, release, bind). Use a callback building method similar to what we do for struct proto. Fixes: c46234eb ("tls: RX path for ktls") Fixes: d4ffb02d ("net/tls: enable sk_msg redirect to tls socket egress") Signed-off-by:
Jakub Kicinski <kuba@kernel.org> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Jakub Kicinski authored
[ Upstream commit e062fe99 ] recvmsg() will put peek()ed and partially read records onto the rx_list. splice_read() needs to consult that list otherwise it may miss data. Align with recvmsg() and also put partially-read records onto rx_list. tls_sw_advance_skb() is pretty pointless now and will be removed in net-next. Fixes: 692d7b5d ("tls: Fix recvmsg() to be able to peek across multiple records") Signed-off-by:
Jakub Kicinski <kuba@kernel.org> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Jakub Kicinski authored
[ Upstream commit 520493f6 ] We don't support splicing control records. TLS 1.3 changes moved the record type check into the decrypt if(). The skb may already be decrypted and still be an alert. Note that decrypt_skb_update() is idempotent and updates ctx->decrypted so the if() is pointless. Reorder the check for decryption errors with the content type check while touching them. This part is not really a bug, because if decryption failed in TLS 1.3 content type will be DATA, and for TLS 1.2 it will be correct. Nevertheless its strange to touch output before checking if the function has failed. Fixes: fedf201e ("net: tls: Refactor control message handling on recv") Signed-off-by:
Jakub Kicinski <kuba@kernel.org> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Huang Pei authored
[ Upstream commit 41ce097f ] It hangup when booting Loongson 3A1000 with BOTH CONFIG_PAGE_SIZE_64KB and CONFIG_MIPS_VA_BITS_48, that it turn out to use 2-level pgtable instead of 3-level. 64KB page size with 2-level pgtable only cover 42 bits VA, use 3-level pgtable to cover all 48 bits VA(55 bits) Fixes: 1e321fa9 ("MIPS64: Support of at least 48 bits of SEGBITS) Signed-off-by:
Huang Pei <huangpei@loongson.cn> Signed-off-by:
Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Huang Pei authored
[ Upstream commit 7db5e9e9 ] It turns out that 'decode_configs' -> 'set_ftlb_enable' is called under c->cputype unset, which leaves FTLB disabled on BOTH 3A2000 and 3A3000 Fix it by calling "decode_configs" after c->cputype is initialized Fixes: da1bd297 ("MIPS: Loongson64: Probe CPU features via CPUCFG") Signed-off-by:
Huang Pei <huangpei@loongson.cn> Signed-off-by:
Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Jesse Brandeburg authored
[ Upstream commit eaeace60 ] Oleksandr brought a bug report where netpoll causes trace messages in the log on igb. Danielle brought this back up as still occurring, so we'll try again. [22038.710800] ------------[ cut here ]------------ [22038.710801] igb_poll+0x0/0x1440 [igb] exceeded budget in poll [22038.710802] WARNING: CPU: 12 PID: 40362 at net/core/netpoll.c:155 netpoll_poll_dev+0x18a/0x1a0 As Alex suggested, change the driver to return work_done at the exit of napi_poll, which should be safe to do in this driver because it is not polling multiple queues in this single napi context (multiple queues attached to one MSI-X vector). Several other drivers contain the same simple sequence, so I hope this will not create new problems. Fixes: 16eb8815 ("igb: Refactor clean_rx_irq to reduce overhead and improve performance") Reported-by:
Oleksandr Natalenko <oleksandr@natalenko.name> Reported-by:
Danielle Ratson <danieller@nvidia.com> Suggested-by:
Alexander Duyck <alexander.duyck@gmail.com> Signed-off-by:
Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by:
Oleksandr Natalenko <oleksandr@natalenko.name> Tested-by:
Danielle Ratson <danieller@nvidia.com> Link: https://lore.kernel.org/r/20211123204000.1597971-1-jesse.brandeburg@intel.com Signed-off-by:
Jakub Kicinski <kuba@kernel.org> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Maurizio Lombardi authored
[ Upstream commit c024b226 ] Submit I/O requests with the IOCB_NOWAIT flag set only if the underlying filesystem supports it. Fixes: 50a909db ("nvmet: use IOCB_NOWAIT for file-ns buffered I/O") Signed-off-by:
Maurizio Lombardi <mlombard@redhat.com> Reviewed-by:
Chaitanya Kulkarni <kch@nvidia.com> Signed-off-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Guo DaXing authored
[ Upstream commit 9ebb0c4b ] The kernel_listen function in smc_listen will fail when all the available ports are occupied. At this point smc->clcsock->sk->sk_data_ready has been changed to smc_clcsock_data_ready. When we call smc_listen again, now both smc->clcsock->sk->sk_data_ready and smc->clcsk_data_ready point to the smc_clcsock_data_ready function. The smc_clcsock_data_ready() function calls lsmc->clcsk_data_ready which now points to itself resulting in an infinite loop. This patch restores smc->clcsock->sk->sk_data_ready with the old value. Fixes: a60a2b1e ("net/smc: reduce active tcp_listen workers") Signed-off-by:
Guo DaXing <guodaxing@huawei.com> Acked-by:
Tony Lu <tonylu@linux.alibaba.com> Signed-off-by:
Karsten Graul <kgraul@linux.ibm.com> Signed-off-by:
Jakub Kicinski <kuba@kernel.org> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Karsten Graul authored
[ Upstream commit 587acad4 ] Coverity reports a possible NULL dereferencing problem: in smc_vlan_by_tcpsk(): 6. returned_null: netdev_lower_get_next returns NULL (checked 29 out of 30 times). 7. var_assigned: Assigning: ndev = NULL return value from netdev_lower_get_next. 1623 ndev = (struct net_device *)netdev_lower_get_next(ndev, &lower); CID 1468509 (#1 of 1): Dereference null return value (NULL_RETURNS) 8. dereference: Dereferencing a pointer that might be NULL ndev when calling is_vlan_dev. 1624 if (is_vlan_dev(ndev)) { Remove the manual implementation and use netdev_walk_all_lower_dev() to iterate over the lower devices. While on it remove an obsolete function parameter comment. Fixes: cb9d43f6 ("net/smc: determine vlan_id of stacked net_device") Suggested-by:
Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by:
Karsten Graul <kgraul@linux.ibm.com> Signed-off-by:
Jakub Kicinski <kuba@kernel.org> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Russell King (Oracle) authored
[ Upstream commit dbae3388 ] On mv88e6xxx 1G/2.5G PCS, the SerDes register 4.2001.2 has the following description: This register bit indicates when link was lost since the last read. For the current link status, read this register back-to-back. Thus to get current link state, we need to read the register twice. But doing that in the link change interrupt handler would lead to potentially ignoring link down events, which we really want to avoid. Thus this needs to be solved in phylink's resolve, by retriggering another resolve in the event when PCS reports link down and previous link was up, and by re-reading PCS state if the previous link was down. The wrong value is read when phylink requests change from sgmii to 2500base-x mode, and link won't come up. This fixes the bug. Fixes: 9525ae83 ("phylink: add phylink infrastructure") Signed-off-by:
Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by:
Marek Behún <kabel@kernel.org> Signed-off-by:
Jakub Kicinski <kuba@kernel.org> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Russell King (Oracle) authored
[ Upstream commit 80662f4f ] On PHY state change the phylink_resolve() function can read stale information from the MAC and report incorrect link speed and duplex to the kernel message log. Example with a Marvell 88X3310 PHY connected to a SerDes port on Marvell 88E6393X switch: - PHY driver triggers state change due to PHY interface mode being changed from 10gbase-r to 2500base-x due to copper change in speed from 10Gbps to 2.5Gbps, but the PHY itself either hasn't yet changed its interface to the host, or the interrupt about loss of SerDes link hadn't arrived yet (there can be a delay of several milliseconds for this), so we still think that the 10gbase-r mode is up - phylink_resolve() - phylink_mac_pcs_get_state() - this fills in speed=10g link=up - interface mode is updated to 2500base-x but speed is left at 10Gbps - phylink_major_config() - interface is changed to 2500base-x - phylink_link_up() - mv88e6xxx_mac_link_up() - .port_set_speed_duplex() - speed is set to 10Gbps - reports "Link is Up - 10Gbps/Full" to dmesg Afterwards when the interrupt finally arrives for mv88e6xxx, another resolve is forced in which we get the correct speed from phylink_mac_pcs_get_state(), but since the interface is not being changed anymore, we don't call phylink_major_config() but only phylink_mac_config(), which does not set speed/duplex anymore. To fix this, we need to force the link down and trigger another resolve on PHY interface change event. Fixes: 9525ae83 ("phylink: add phylink infrastructure") Signed-off-by:
Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by:
Marek Behún <kabel@kernel.org> Signed-off-by:
Jakub Kicinski <kuba@kernel.org> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Heiner Kallweit authored
[ Upstream commit ddb826c2 ] Usage of phy_ethtool_get_link_ksettings() in the link status change handler isn't needed, and in combination with the referenced change it results in a deadlock. Simply remove the call and replace it with direct access to phydev->speed. The duplex argument of lan743x_phy_update_flowcontrol() isn't used and can be removed. Fixes: c10a485c ("phy: phy_ethtool_ksettings_get: Lock the phy for consistency") Reported-by:
Alessandro B Maurici <abmaurici@gmail.com> Tested-by:
Alessandro B Maurici <abmaurici@gmail.com> Signed-off-by:
Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/40e27f76-0ba3-dcef-ee32-a78b9df38b0f@gmail.com Signed-off-by:
Jakub Kicinski <kuba@kernel.org> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Eric Dumazet authored
[ Upstream commit 4e1fddc9 ] While testing BIG TCP patch series, I was expecting that TCP_RR workloads with 80KB requests/answers would send one 80KB TSO packet, then being received as a single GRO packet. It turns out this was not happening, and the root cause was that cubic Hystart ACK train was triggering after a few (2 or 3) rounds of RPC. Hystart was wrongly setting CWND/SSTHRESH to 30, while my RPC needed a budget of ~20 segments. Ideally these TCP_RR flows should not exit slow start. Cubic Hystart should reset itself at each round, instead of assuming every TCP flow is a bulk one. Note that even after this patch, Hystart can still trigger, depending on scheduling artifacts, but at a higher CWND/SSTHRESH threshold, keeping optimal TSO packet sizes. Tested: ip link set dev eth0 gro_ipv6_max_size 131072 gso_ipv6_max_size 131072 nstat -n; netperf -H ... -t TCP_RR -l 5 -- -r 80000,80000 -K cubic; nstat|egrep "Ip6InReceives|Hystart|Ip6OutRequests" Before: 8605 Ip6InReceives 87541 0.0 Ip6OutRequests 129496 0.0 TcpExtTCPHystartTrainDetect 1 0.0 TcpExtTCPHystartTrainCwnd 30 0.0 After: 8760 Ip6InReceives 88514 0.0 Ip6OutRequests 87975 0.0 Fixes: ae27e98a ("[TCP] CUBIC v2.3") Co-developed-by:
Neal Cardwell <ncardwell@google.com> Signed-off-by:
Neal Cardwell <ncardwell@google.com> Signed-off-by:
Eric Dumazet <edumazet@google.com> Cc: Stephen Hemminger <stephen@networkplumber.org> Cc: Yuchung Cheng <ycheng@google.com> Cc: Soheil Hassas Yeganeh <soheil@google.com> Link: https://lore.kernel.org/r/20211123202535.1843771-1-eric.dumazet@gmail.com Signed-off-by:
Jakub Kicinski <kuba@kernel.org> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Nicholas Kazlauskas authored
[ Upstream commit 21431f70 ] [Why] We're only setting the flags on stream[0]'s planes so this logic fails if we have more than one stream in the state. This can cause a page flip timeout with multiple displays in the configuration. [How] Index into the stream_status array using the stream index - it's a 1:1 mapping. Fixes: cdaae837 ("drm/amd/display: Handle GPU reset for DC block") Reviewed-by:
Harry Wentland <Harry.Wentland@amd.com> Acked-by:
Qingqing Zhuo <qingqing.zhuo@amd.com> Signed-off-by:
Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Tested-by:
Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Nicholas Kazlauskas authored
[ Upstream commit 6eff272d ] [Why] The HW interrupt gets disabled after GPU reset so we don't receive notifications for HPD or AUX from DMUB - leading to timeout and black screen with (or without) DPIA links connected. [How] Re-enable the interrupt after GPU reset like we do for the other DC interrupts. Fixes: 81927e28 ("drm/amd/display: Support for DMUB AUX") Reviewed-by:
Jude Shih <Jude.Shih@amd.com> Acked-by:
Qingqing Zhuo <qingqing.zhuo@amd.com> Signed-off-by:
Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Tested-by:
Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Thomas Zeitlhofer authored
[ Upstream commit cefcf24b ] Commit 39fbef4b ("PM: hibernate: Get block device exclusively in swsusp_check()") changed the opening mode of the block device to (FMODE_READ | FMODE_EXCL). In the corresponding calls to swsusp_close(), the mode is still just FMODE_READ which triggers the warning in blkdev_flush_mapping() on resume from hibernate. So, use the mode (FMODE_READ | FMODE_EXCL) also when closing the device. Fixes: 39fbef4b ("PM: hibernate: Get block device exclusively in swsusp_check()") Signed-off-by:
Thomas Zeitlhofer <thomas.zeitlhofer+lkml@ze-it.at> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Kumar Thangavel authored
[ Upstream commit ac132852 ] Update NC-SI command handler (both standard and OEM) to take into account of payload paddings in allocating skb (in case of payload size is not 32-bit aligned). The checksum field follows payload field, without taking payload padding into account can cause checksum being truncated, leading to dropped packets. Fixes: fb4ee675 ("net/ncsi: Add NCSI OEM command support") Signed-off-by:
Kumar Thangavel <thangavel.k@hcl.com> Acked-by:
Samuel Mendoza-Jonas <sam@mendozajonas.com> Reviewed-by:
Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Mark Rutland authored
[ Upstream commit 94902d84 ] As Vincent reports in: https://lore.kernel.org/r/20211118163417.21617-1-vincent.whitchurch@axis.com The put_user() in schedule_tail() can get stuck in a livelock, similar to a problem recently fixed on riscv in commit: 285a76bb ("riscv: evaluate put_user() arg before enabling user access") In __raw_put_user() we have a critical section between uaccess_ttbr0_enable() and uaccess_ttbr0_disable() where we cannot safely call into the scheduler without having taken an exception, as schedule() and other scheduling functions will not save/restore the TTBR0 state. If either of the `x` or `ptr` arguments to __raw_put_user() contain a blocking call, we may call into the scheduler within the critical section. This can result in two problems: 1) The access within the critical section will occur without the required TTBR0 tables installed. This will fault, and where the required tables permit access, the access will be retried without the required tables, resulting in a livelock. 2) When TTBR0 SW PAN is in use, check_and_switch_context() does not modify TTBR0, leaving a stale value installed. The mappings of the blocked task will erroneously be accessible to regular accesses in the context of the new task. Additionally, if the tables are subsequently freed, local TLB maintenance required to reuse the ASID may be lost, potentially resulting in TLB corruption (e.g. in the presence of CnP). The same issue exists for __raw_get_user() in the critical section between uaccess_ttbr0_enable() and uaccess_ttbr0_disable(). A similar issue exists for __get_kernel_nofault() and __put_kernel_nofault() for the critical section between __uaccess_enable_tco_async() and __uaccess_disable_tco_async(), as the TCO state is not context-switched by direct calls into the scheduler. Here the TCO state may be lost from the context of the current task, resulting in unexpected asynchronous tag check faults. It may also be leaked to another task, suppressing expected tag check faults. To fix all of these cases, we must ensure that we do not directly call into the scheduler in their respective critical sections. This patch reworks __raw_put_user(), __raw_get_user(), __get_kernel_nofault(), and __put_kernel_nofault(), ensuring that parameters are evaluated outside of the critical sections. To make this requirement clear, comments are added describing the problem, and line spaces added to separate the critical sections from other portions of the macros. For __raw_get_user() and __raw_put_user() the `err` parameter is conditionally assigned to, and we must currently evaluate this in the critical section. This behaviour is relied upon by the signal code, which uses chains of put_user_error() and get_user_error(), checking the return value at the end. In all cases, the `err` parameter is a plain int rather than a more complex expression with a blocking call, so this is safe. In future we should try to clean up the `err` usage to remove the potential for this to be a problem. Aside from the changes to time of evaluation, there should be no functional change as a result of this patch. Reported-by:
Vincent Whitchurch <vincent.whitchurch@axis.com> Link: https://lore.kernel.org/r/20211118163417.21617-1-vincent.whitchurch@axis.com Fixes: f253d827 ("arm64: uaccess: refactor __{get,put}_user") Signed-off-by:
Mark Rutland <mark.rutland@arm.com> Cc: Will Deacon <will@kernel.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Link: https://lore.kernel.org/r/20211122125820.55286-1-mark.rutland@arm.com Signed-off-by:
Will Deacon <will@kernel.org> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Mohammed Gamal authored
[ Upstream commit e048834c ] The Hyper-V DRM driver tries to free MMIO region on removing the device regardless of VM type, while Gen1 VMs don't use MMIO and hence causing the kernel to crash on a NULL pointer dereference. Fix this by making deallocating MMIO only on Gen2 machines and implement removal for Gen1 Fixes: 76c56a5a ("drm/hyperv: Add DRM driver for hyperv synthetic video device") Signed-off-by:
Mohammed Gamal <mgamal@redhat.com> Reviewed-by:
Deepak Rawat <drawat.floss@gmail.com> Signed-off-by:
Deepak Rawat <drawat.floss@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/20211119112900.300537-1-mgamal@redhat.com Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Varun Prakash authored
[ Upstream commit 102110ef ] Current nvmet_try_send_ddgst() code does not check whether all data digest bytes are transmitted, fix this by returning -EAGAIN if all data digest bytes are not transmitted. Fixes: 872d26a3 ("nvmet-tcp: add NVMe over TCP target driver") Signed-off-by:
Varun Prakash <varun@chelsio.com> Reviewed-by:
Sagi Grimberg <sagi@grimberg.me> Signed-off-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Adamos Ttofari authored
[ Upstream commit cd23f02f ] Commit fbdc21e9 ("cpufreq: intel_pstate: Add Icelake servers support in no-HWP mode") enabled the use of Intel P-State driver for Ice Lake servers. But it doesn't cover the case when OS can't control P-States. Therefore, for Ice Lake server, if MSR_MISC_PWR_MGMT bits 8 or 18 are enabled, then the Intel P-State driver should exit as OS can't control P-States. Fixes: fbdc21e9 ("cpufreq: intel_pstate: Add Icelake servers support in no-HWP mode") Signed-off-by:
Adamos Ttofari <attofari@amazon.de> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Marek Behún authored
[ Upstream commit 7b1b62bc ] Currently mvpp2_xdp_setup won't allow attaching XDP program if mtu > ETH_DATA_LEN (1500). The mvpp2_change_mtu on the other hand checks whether MVPP2_RX_PKT_SIZE(mtu) > MVPP2_BM_LONG_PKT_SIZE. These two checks are semantically different. Moreover this limit can be increased to MVPP2_MAX_RX_BUF_SIZE, since in mvpp2_rx we have xdp.data = data + MVPP2_MH_SIZE + MVPP2_SKB_HEADROOM; xdp.frame_sz = PAGE_SIZE; Change the checks to check whether mtu > MVPP2_MAX_RX_BUF_SIZE Fixes: 07dd0a7a ("mvpp2: add basic XDP support") Signed-off-by:
Marek Behún <kabel@kernel.org> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Alex Elder authored
[ Upstream commit e4e9bfb7 ] Calling ipa_cmd_pipeline_clear() after stopping the channel underlying the AP<-modem RX endpoint can lead to a deadlock. This occurs in the ->runtime_suspend device power operation for the IPA driver. While this callback is in progress, any other requests for power will block until the callback returns. Stopping the AP<-modem RX channel does not prevent the modem from sending another packet to this endpoint. If a packet arrives for an RX channel when the channel is stopped, an SUSPEND IPA interrupt condition will be pending. Handling an IPA interrupt requires power, so ipa_isr_thread() calls pm_runtime_get_sync() first thing. The problem occurs because a "pipeline clear" command will not complete while such a SUSPEND interrupt condition exists. So the SUSPEND IPA interrupt handler won't proceed until it gets power; that won't happen until the ->runtime_suspend callback (and its "pipeline clear" command) completes; and that can't happen while the SUSPEND interrupt condition exists. It turns out that in this case there is no need to use the "pipeline clear" command. There are scenarios in which clearing the pipeline is required while suspending, but those are not (yet) supported upstream. So a simple fix, avoiding the potential deadlock, is to stop calling ipa_cmd_pipeline_clear() in ipa_endpoint_suspend(). This removes the only user of ipa_cmd_pipeline_clear(), so get rid of that function. It can be restored again whenever it's needed. This is basically a manual revert along with an explanation for commit 6cb63ea6 ("net: ipa: introduce ipa_cmd_tag_process()"). Fixes: 6cb63ea6 ("net: ipa: introduce ipa_cmd_tag_process()") Signed-off-by:
Alex Elder <elder@linaro.org> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Alex Elder authored
[ Upstream commit 8afc7e47 ] The IPA setup_complete flag is set at the end of ipa_setup(), when the setup phase of initialization has completed successfully. This occurs as part of driver probe processing, or (if "modem-init" is specified in the DTS file) it is triggered by the "ipa-setup-ready" SMP2P interrupt generated by the modem. In the latter case, it's possible for driver shutdown (or remove) to begin while setup processing is underway, and this can't be allowed. The problem is that the setup_complete flag is not adequate to signal that setup is underway. If setup_complete is set, it will never be un-set, so that case is not a problem. But if setup_complete is false, there's a chance setup is underway. Because setup is triggered by an interrupt on a "modem-init" system, there is a simple way to ensure the value of setup_complete is safe to read. The threaded handler--if it is executing--will complete as part of a request to disable the "ipa-modem-ready" interrupt. This means that ipa_setup() (which is called from the handler) will run to completion if it was underway, or will never be called otherwise. The request to disable the "ipa-setup-ready" interrupt is currently made within ipa_modem_stop(). Instead, disable the interrupt outside that function in the two places it's called. In the case of ipa_remove(), this ensures the setup_complete flag is safe to read before we read it. Rename ipa_smp2p_disable() to be ipa_smp2p_irq_disable_setup(), to be more specific about its effect. Fixes: 530f9216 ("soc: qcom: ipa: AP/modem communications") Signed-off-by:
Alex Elder <elder@linaro.org> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Alex Elder authored
[ Upstream commit 33a15310 ] We currently maintain a "disabled" Boolean flag to determine whether the "ipa-setup-ready" SMP2P IRQ handler does anything. That flag must be accessed under protection of a mutex. Instead, disable the SMP2P interrupt when requested, which prevents the interrupt handler from ever being called. More importantly, it synchronizes a thread disabling the interrupt with the completion of the interrupt handler in case they run concurrently. Use the IPA setup_complete flag rather than the disabled flag in the handler to determine whether to ignore any interrupts arriving after the first. Rename the "disabled" flag to be "setup_disabled", to be specific about its purpose. Fixes: 530f9216 ("soc: qcom: ipa: AP/modem communications") Signed-off-by:
Alex Elder <elder@linaro.org> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Amit Cohen authored
[ Upstream commit 63b08b1f ] When processing port up/down events generated by the device's firmware, the driver protects itself from events reported for non-existent local ports, but not the CPU port (local port 0), which exists, but lacks a netdev. This can result in a NULL pointer dereference when calling netif_carrier_{on,off}(). Fix this by bailing early when processing an event reported for the CPU port. Problem was only observed when running on top of a buggy emulator. Fixes: 28b1987e ("mlxsw: spectrum: Register CPU port with devlink") Signed-off-by:
Amit Cohen <amcohen@nvidia.com> Signed-off-by:
Ido Schimmel <idosch@nvidia.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Tony Lu authored
[ Upstream commit 606a63c9 ] The side that actively closed socket, it's clcsock doesn't enter TIME_WAIT state, but the passive side does it. It should show the same behavior as TCP sockets. Consider this, when client actively closes the socket, the clcsock in server enters TIME_WAIT state, which means the address is occupied and won't be reused before TIME_WAIT dismissing. If we restarted server, the service would be unavailable for a long time. To solve this issue, shutdown the clcsock in [A], perform the TCP active close progress first, before the passive closed side closing it. So that the actively closed side enters TIME_WAIT, not the passive one. Client | Server close() // client actively close | smc_release() | smc_close_active() // PEERCLOSEWAIT1 | smc_close_final() // abort or closed = 1| smc_cdc_get_slot_and_msg_send() | [A] | |smc_cdc_msg_recv_action() // ACTIVE | queue_work(smc_close_wq, &conn->close_work) | smc_close_passive_work() // PROCESSABORT or APPCLOSEWAIT1 | smc_close_passive_abort_received() // only in abort | |close() // server recv zero, close | smc_release() // PROCESSABORT or APPCLOSEWAIT1 | smc_close_active() | smc_close_abort() or smc_close_final() // CLOSED | smc_cdc_get_slot_and_msg_send() // abort or closed = 1 smc_cdc_msg_recv_action() | smc_clcsock_release() queue_work(smc_close_wq, &conn->close_work) | sock_release(tcp) // actively close clc, enter TIME_WAIT smc_close_passive_work() // PEERCLOSEWAIT1 | smc_conn_free() smc_close_passive_abort_received() // CLOSED| smc_conn_free() | smc_clcsock_release() | sock_release(tcp) // passive close clc | Link: https://www.spinics.net/lists/netdev/msg780407.html Fixes: b38d7324 ("smc: socket closing and linkgroup cleanup") Signed-off-by:
Tony Lu <tonylu@linux.alibaba.com> Reviewed-by:
Wen Gu <guwen@linux.alibaba.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Vincent Whitchurch authored
[ Upstream commit 84e1d0bf ] If a timeout is hit, it can result is incorrect data on the I2C bus and/or memory corruptions in the guest since the device can still be operating on the buffers it was given while the guest has freed them. Here is, for example, the start of a slub_debug splat which was triggered on the next transfer after one transfer was forced to timeout by setting a breakpoint in the backend (rust-vmm/vhost-device): BUG kmalloc-1k (Not tainted): Poison overwritten First byte 0x1 instead of 0x6b Allocated in virtio_i2c_xfer+0x65/0x35c age=350 cpu=0 pid=29 __kmalloc+0xc2/0x1c9 virtio_i2c_xfer+0x65/0x35c __i2c_transfer+0x429/0x57d i2c_transfer+0x115/0x134 i2cdev_ioctl_rdwr+0x16a/0x1de i2cdev_ioctl+0x247/0x2ed vfs_ioctl+0x21/0x30 sys_ioctl+0xb18/0xb41 Freed in virtio_i2c_xfer+0x32e/0x35c age=244 cpu=0 pid=29 kfree+0x1bd/0x1cc virtio_i2c_xfer+0x32e/0x35c __i2c_transfer+0x429/0x57d i2c_transfer+0x115/0x134 i2cdev_ioctl_rdwr+0x16a/0x1de i2cdev_ioctl+0x247/0x2ed vfs_ioctl+0x21/0x30 sys_ioctl+0xb18/0xb41 There is no simple fix for this (the driver would have to always create bounce buffers and hold on to them until the device eventually returns the buffers), so just disable the timeout support for now. Fixes: 3cfc8838 ("i2c: virtio: add a virtio i2c frontend driver") Acked-by:
Jie Deng <jie.deng@intel.com> Signed-off-by:
Vincent Whitchurch <vincent.whitchurch@axis.com> Acked-by:
Michael S. Tsirkin <mst@redhat.com> Reviewed-by:
Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by:
Wolfram Sang <wsa@kernel.org> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Huang Jianan authored
[ Upstream commit 57bbeacd ] We observed the following deadlock in the stress test under low memory scenario: Thread A Thread B - erofs_shrink_scan - erofs_try_to_release_workgroup - erofs_workgroup_try_to_freeze -- A - z_erofs_do_read_page - z_erofs_collection_begin - z_erofs_register_collection - erofs_insert_workgroup - xa_lock(&sbi->managed_pslots) -- B - erofs_workgroup_get - erofs_wait_on_workgroup_freezed -- A - xa_erase - xa_lock(&sbi->managed_pslots) -- B To fix this, it needs to hold xa_lock before freezing the workgroup since xarray will be touched then. So let's hold the lock before accessing each workgroup, just like what we did with the radix tree before. [ Gao Xiang: Jianhua Hao also reports this issue at https://lore.kernel.org/r/b10b85df30694bac8aadfe43537c897a@xiaomi.com ] Link: https://lore.kernel.org/r/20211118135844.3559-1-huangjianan@oppo.com Fixes: 64094a04 ("erofs: convert workstn to XArray") Reviewed-by:
Chao Yu <chao@kernel.org> Reviewed-by:
Gao Xiang <hsiangkao@linux.alibaba.com> Signed-off-by:
Huang Jianan <huangjianan@oppo.com> Reported-by:
Jianhua Hao <haojianhua1@xiaomi.com> Signed-off-by:
Gao Xiang <xiang@kernel.org> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Shin'ichiro Kawasaki authored
[ Upstream commit 2d62253e ] When a reset is requested the position of the write pointer is updated but the data in the corresponding zone is not cleared. Instead scsi_debug returns any data written before the write pointer was reset. This is an error and prevents using scsi_debug for stale page cache testing of the BLKRESETZONE ioctl. Zero written data in the zone when resetting the write pointer. Link: https://lore.kernel.org/r/20211122061223.298890-1-shinichiro.kawasaki@wdc.com Fixes: f0d1cf93 ("scsi: scsi_debug: Add ZBC zone commands") Reviewed-by:
Damien Le Moal <damien.lemoal@opensource.wdc.com> Acked-by:
Douglas Gilbert <dgilbert@interlog.com> Signed-off-by:
Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Mike Christie authored
[ Upstream commit eb97545d ] This fixes an issue added in commit 4edd8cd4 ("scsi: core: sysfs: Fix hang when device state is set via sysfs") where if userspace is requesting to set the device state to SDEV_RUNNING when the state is already SDEV_RUNNING, we return -EINVAL instead of count. The commmit above set ret to count for this case, when it should have set it to 0. Link: https://lore.kernel.org/r/20211120164917.4924-1-michael.christie@oracle.com Fixes: 4edd8cd4 ("scsi: core: sysfs: Fix hang when device state is set via sysfs") Reviewed-by:
Lee Duncan <lduncan@suse.com> Signed-off-by:
Mike Christie <michael.christie@oracle.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-