- Oct 06, 2023
-
-
Richard Fitzgerald authored
[ Upstream commit 69343ce9 ] Change the logging of each algorithm from info level to debug level. On the original devices supported by this code there were typically only one or two algorithms in a firmware and one or two DSPs so this logging only used a small number of log lines. However, for the latest devices there could be 30-40 algorithms in a firmware and 8 DSPs being loaded in parallel, so using 300+ lines of log for information that isn't particularly important to have logged. Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com> Link: https://lore.kernel.org/r/20230913160523.3701189-1-rf@opensource.cirrus.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Richard Fitzgerald authored
[ Upstream commit a479b44a ] The ACPI setting for a GPIO default state has higher priority than the flag passed to devm_gpiod_get_optional() so ACPI can override the GPIOD_OUT_LOW. Explicitly set the GPIO low when hard resetting. Although GPIOD_OUT_LOW can't be relied on this doesn't seem like a reason to stop passing it to devm_gpiod_get_optional(). So we still pass it to state our intent, but can deal with it having no effect. Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com> Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com> Link: https://lore.kernel.org/r/20230913150012.604775-3-sbinding@opensource.cirrus.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Richard Fitzgerald authored
[ Upstream commit 41dac81b ] The CS42L42 can accept very short reset pulses of a few microseconds but there's no reason to force a very short pulse. Allow a wide range for the usleep_range() so it can be relaxed about the choice of timing source. Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com> Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com> Link: https://lore.kernel.org/r/20230913150012.604775-2-sbinding@opensource.cirrus.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Peter Ujfalusi authored
[ Upstream commit 485ddd51 ] Use consistently u8 for sdw link index. The id is limited to 4, u8 is adequate in size to store it. This change will also fixes the following compiler warning/error (W=1): sound/hda/intel-sdw-acpi.c: In function ‘sdw_intel_acpi_scan’: sound/hda/intel-sdw-acpi.c:34:35: error: ‘-subproperties’ directive output may be truncated writing 14 bytes into a region of size between 7 and 17 [-Werror=format-truncation=] 34 | "mipi-sdw-link-%d-subproperties", i); | ^~~~~~~~~~~~~~ In function ‘is_link_enabled’, inlined from ‘sdw_intel_scan_controller’ at sound/hda/intel-sdw-acpi.c:106:8, inlined from ‘sdw_intel_acpi_scan’ at sound/hda/intel-sdw-acpi.c:180:9: sound/hda/intel-sdw-acpi.c:33:9: note: ‘snprintf’ output between 30 and 40 bytes into a destination of size 32 33 | snprintf(name, sizeof(name), | ^~~~~~~~~~~~~~~~~~~~~~~~~~~~ 34 | "mipi-sdw-link-%d-subproperties", i); | ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ cc1: all warnings being treated as errors The warnings got brought to light by a recent patch upstream: commit 6d4ab2e9 ("extrawarn: enable format and stringop overflow warnings in W=1") Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com> Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20230912162617.29178-1-peter.ujfalusi@linux.intel.com Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Stanislav Fomichev authored
[ Upstream commit 7cb779a6 ] Commit 151e887d ("veth: Fixing transmit return status for dropped packets") exposed the fact that bpf_clone_redirect is capable of returning raw NET_XMIT_XXX return codes. This is in the conflict with its UAPI doc which says the following: "0 on success, or a negative error in case of failure." Update the UAPI to reflect the fact that bpf_clone_redirect can return positive error numbers, but don't explicitly define their meaning. Reported-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Stanislav Fomichev <sdf@google.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20230911194731.286342-1-sdf@google.com Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Mika Westerberg authored
[ Upstream commit 9855d60c ] Intel Granite Rapids has a flash controller that is compatible with the other Cannon Lake derivatives. Add Granite Rapids PCI ID to the driver list of supported devices. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Link: https://lore.kernel.org/r/20230911074616.3473347-1-mika.westerberg@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Shengjiu Wang authored
[ Upstream commit 2f942690 ] The rpmsg pcm device is a device which should support double buffering. Found this issue with pipewire. When there is no SNDRV_PCM_INFO_BATCH flag in driver, the pipewire will set headroom to be zero, and because rpmsg pcm device don't support residue report, when the latency setting is small, the "delay" always larger than "target" in alsa-pcm.c, that reading next period data is not scheduled on time. With SNDRV_PCM_INFO_BATCH flag in driver, the pipewire will select a smaller period size for device, then the task of reading next period data will be scheduled on time. Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com> Link: https://lore.kernel.org/r/1694414287-13291-1-git-send-email-shengjiu.wang@nxp.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Valentin Caron authored
[ Upstream commit 6de8a70c ] As explained in errata sheet, in section "2.14.5 Truncation of SPI output signals after EOT event": On STM32MP1x, EOT interrupt can be thrown before the true end of communication. So we add a delay of a half period to wait the real end of the transmission. Link: https://www.st.com/resource/en/errata_sheet/es0539-stm32mp131x3x5x-device-errata-stmicroelectronics.pdf Signed-off-by: Valentin Caron <valentin.caron@foss.st.com> Link: https://lore.kernel.org/r/20230906132735.748174-1-valentin.caron@foss.st.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Han Xu authored
[ Upstream commit 18495676 ] Reset the FLSHxCR1 registers to default value. ROM may set the register value and it affects the SPI NAND normal functions. Signed-off-by: Han Xu <han.xu@nxp.com> Link: https://lore.kernel.org/r/20230906183254.235847-1-han.xu@nxp.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Niklas Cassel authored
[ Upstream commit 80cc944e ] ata_scsi_port_error_handler() starts off by clearing ATA_PFLAG_EH_PENDING, before calling ap->ops->error_handler() (without holding the ap->lock). If an error IRQ is received while ap->ops->error_handler() is running, the irq handler will set ATA_PFLAG_EH_PENDING. Once ap->ops->error_handler() returns, ata_scsi_port_error_handler() checks if ATA_PFLAG_EH_PENDING is set, and if it is, another iteration of ATA EH is performed. The problem is that ATA_PFLAG_EH_PENDING is not only cleared by ata_scsi_port_error_handler(), it is also cleared by ata_eh_reset(). ata_eh_reset() is called by ap->ops->error_handler(). This additional clearing done by ata_eh_reset() breaks the whole retry logic in ata_scsi_port_error_handler(). Thus, if an error IRQ is received while ap->ops->error_handler() is running, the port will currently remain frozen and will never get re-enabled. The additional clearing in ata_eh_reset() was introduced in commit 1e641060 ("libata: clear eh_info on reset completion"). Looking at the original error report: https://marc.info/?l=linux-ide&m=124765325828495&w=2 We can see the following happening: [ 1.074659] ata3: XXX port freeze [ 1.074700] ata3: XXX hardresetting link, stopping engine [ 1.074746] ata3: XXX flipping SControl [ 1.411471] ata3: XXX irq_stat=400040 CONN|PHY [ 1.411475] ata3: XXX port freeze [ 1.420049] ata3: XXX starting engine [ 1.420096] ata3: XXX rc=0, class=1 [ 1.420142] ata3: XXX clearing IRQs for thawing [ 1.420188] ata3: XXX port thawed [ 1.420234] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) We are not supposed to be able to receive an error IRQ while the port is frozen (PxIE is set to 0, i.e. all IRQs for the port are disabled). AHCI 1.3.1 section 10.7.1.1 First Tier (IS Register) states: "Each bit location can be thought of as reporting a '1' if the virtual "interrupt line" for that port is indicating it wishes to generate an interrupt. That is, if a port has one or more interrupt status bit set, and the enables for those status bits are set, then this bit shall be set." Additionally, AHCI state P:ComInit clearly shows that the state machine will only jump to P:ComInitSetIS (which sets IS.IPS(x) to '1'), if PxIE.PCE is set to '1'. In our case, PxIE is set to 0, so IS.IPS(x) won't get set. So IS.IPS(x) only gets set if PxIS and PxIE is set. AHCI 1.3.1 section 10.7.1.1 First Tier (IS Register) also states: "The bits in this register are read/write clear. It is set by the level of the virtual interrupt line being a set, and cleared by a write of '1' from the software." So if IS.IPS(x) is set, you need to explicitly clear it by writing a 1 to IS.IPS(x) for that port. Since PxIE is cleared, the only way to get an interrupt while the port is frozen, is if IS.IPS(x) is set, and the only way IS.IPS(x) can be set when the port is frozen, is if it was set before the port was frozen. However, since commit 737dd811 ("ata: libahci: clear pending interrupt status"), we clear both PxIS and IS.IPS(x) after freezing the port, but before the COMRESET, so the problem that commit 1e641060 ("libata: clear eh_info on reset completion") fixed can no longer happen. Thus, revert commit 1e641060 ("libata: clear eh_info on reset completion"), so that the retry logic in ata_scsi_port_error_handler() works once again. (The retry logic is still needed, since we can still get an error IRQ _after_ the port has been thawed, but before ata_scsi_port_error_handler() takes the ap->lock in order to check if ATA_PFLAG_EH_PENDING is set.) Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com> Signed-off-by: Damien Le Moal <dlemoal@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Steve French authored
[ Upstream commit ebc3d4e4 ] checkpatch flagged a few places with: WARNING: ENOTSUPP is not a SUSV4 error code, prefer EOPNOTSUPP Also fixed minor typo Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Michal Grzedzicki authored
[ Upstream commit c13e7331 ] Tags allocated for OPC_INB_SET_CONTROLLER_CONFIG command need to be freed when we receive the response. Signed-off-by: Michal Grzedzicki <mge@meta.com> Link: https://lore.kernel.org/r/20230911170340.699533-2-mge@meta.com Acked-by: Jack Wang <jinpu.wang@ionos.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Michal Grzedzicki authored
[ Upstream commit 71996bb8 ] Some cards have more than one SAS address. Using an incorrect address causes communication issues with some devices like expanders. Closes: https://lore.kernel.org/linux-kernel/A57AEA84-5CA0-403E-8053-106033C73C70@fb.com/ Signed-off-by: Michal Grzedzicki <mge@meta.com> Link: https://lore.kernel.org/r/20230913155611.3183612-1-mge@meta.com Acked-by: Jack Wang <jinpu.wang@ionos.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Icenowy Zheng authored
[ Upstream commit 8eb8fe67 ] The dcache.cva encoding shown in the comments are wrong, it's for dcache.cval1 (which is restricted to L1) instead. Fix this in the comment and in the hardcoded instruction. Signed-off-by: Icenowy Zheng <uwu@icenowy.me> Tested-by: Sergey Matyukevich <sergey.matyukevich@syntacore.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Guo Ren <guoren@kernel.org> Tested-by: Drew Fustini <dfustini@baylibre.com> Link: https://lore.kernel.org/r/20230912072410.2481-1-jszhang@kernel.org Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
David Francis authored
[ Upstream commit 5e7e8225 ] On some APU systems, there is no atom context and so the atom_context struct is null. Add a check to the VBIOS_INFO branch of amdgpu_info_ioctl to handle this case, returning all zeroes. Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: David Francis <David.Francis@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Alex Deucher authored
[ Upstream commit ab43213e ] Needed for HDP flush to work correctly. Reviewed-by: Timmy Tsai <timmtsai@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Alex Deucher authored
[ Upstream commit 1832403c ] This matches the behavior for soc15 and nv. Acked-by: Christian König <christian.koenig@amd.com> Reviewed-by: Timmy Tsai <timmtsai@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Swapnil Patel authored
[ Upstream commit f5b2c10b ] [Why] Currently the driver looks DCN registers to access if BL is on or not. This check is not valid if we are using AUX based brightness control. This causes driver to not send out "backlight off" command during power off sequence as it already thinks it is off. [How] Only check DCN registers if we aren't using AUX based brightness control. Reviewed-by: Wenjing Liu <wenjing.liu@amd.com> Acked-by: Stylon Wang <stylon.wang@amd.com> Signed-off-by: Swapnil Patel <swapnil.patel@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Julia Lawall authored
[ Upstream commit 8a81cf96 ] for_each_child_of_node performs an of_node_get on each iteration, so a break out of the loop requires an of_node_put. This was done using the Coccinelle semantic patch iterators/for_each_child.cocci Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Luke D. Jones authored
[ Upstream commit 4106a70d ] Add quirk for ASUS ROG X16 (GV601V, 2023 versions) Flow 2-in-1 to enable tablet mode with lid flip (all screen rotations). Signed-off-by: Luke D. Jones <luke@ljones.dev> Link: https://lore.kernel.org/r/20230905082813.13470-1-luke@ljones.dev Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
David Thompson authored
[ Upstream commit c2dffda1 ] The latest version of the mlxbf_bootctl driver utilizes "sysfs_format_mac", and this API is only available if NET is defined in the kernel configuration. This patch changes the mlxbf_bootctl Kconfig to depend on NET. Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202309031058.JvwNDBKt-lkp@intel.com/ Reported-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: David Thompson <davthompson@nvidia.com> Link: https://lore.kernel.org/r/20230905133243.31550-1-davthompson@nvidia.com Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Christophe JAILLET authored
[ Upstream commit e97eb65d ] snprintf() returns the "number of characters which *would* be generated for the given input", not the size *really* generated. In order to avoid too large values for 'o' (and potential negative values for "sizeof(linebuf) o") use scnprintf() instead of snprintf(). Note that given the "w < 4" in the for loop, the buffer can NOT overflow, but using the *right* function is always better. Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: Damien Le Moal <dlemoal@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Guangguan Wang authored
[ Upstream commit 6912e724 ] In the macro SMC_STAT_SERV_SUCC_INC, the smcd_version is used to determin whether to increase the v1 statistic or the v2 statistic. It is correct for SMCD. But for SMCR, smcr_version should be used. Signed-off-by: Guangguan Wang <guangguan.wang@linux.alibaba.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Steven Rostedt (Google) authored
[ Upstream commit 95a404bd ] When iterating over the ring buffer while the ring buffer is active, the writer can corrupt the reader. There's barriers to help detect this and handle it, but that code missed the case where the last event was at the very end of the page and has only 4 bytes left. The checks to detect the corruption by the writer to reads needs to see the length of the event. If the length in the first 4 bytes is zero then the length is stored in the second 4 bytes. But if the writer is in the process of updating that code, there's a small window where the length in the first 4 bytes could be zero even though the length is only 4 bytes. That will cause rb_event_length() to read the next 4 bytes which could happen to be off the allocated page. To protect against this, fail immediately if the next event pointer is less than 8 bytes from the end of the commit (last byte of data), as all events must be a minimum of 8 bytes anyway. Link: https://lore.kernel.org/all/20230905141245.26470-1-Tze-nan.Wu@mediatek.com/ Link: https://lore.kernel.org/linux-trace-kernel/20230907122820.0899019c@gandalf.local.home Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Reported-by: Tze-nan Wu <Tze-nan.Wu@mediatek.com> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Ricardo B. Marliere authored
[ Upstream commit 5f9dd2e8 ] This patch fixes inconsistencies in the parsing rules of the levels 1 and 2 of the kselftest_deps.sh. It was added the levels 4 and 5 to account for a few edge cases that are present in some tests, also some minor identation styling have been fixed (s/ /\t/g). Signed-off-by: Ricardo B. Marliere <rbmarliere@gmail.com> Signed-off-by: Shuah Khan <skhan@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Filipe Manana authored
[ Upstream commit a57c2d4e ] When removing a delayed item, or releasing which will remove it as well, we will modify one of the delayed node's rbtrees and item counter if the delayed item is in one of the rbtrees. This require having the delayed node's mutex locked, otherwise we will race with other tasks modifying the rbtrees and the counter. This is motivated by a previous version of another patch actually calling btrfs_release_delayed_item() after unlocking the delayed node's mutex and against a delayed item that is in a rbtree. So assert at __btrfs_remove_delayed_item() that the delayed node's mutex is locked. Reviewed-by: Qu Wenruo <wqu@suse.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Zheng Yejian authored
[ Upstream commit f6bd2c92 ] When user resize all trace ring buffer through file 'buffer_size_kb', then in ring_buffer_resize(), kernel allocates buffer pages for each cpu in a loop. If the kernel preemption model is PREEMPT_NONE and there are many cpus and there are many buffer pages to be allocated, it may not give up cpu for a long time and finally cause a softlockup. To avoid it, call cond_resched() after each cpu buffer allocation. Link: https://lore.kernel.org/linux-trace-kernel/20230906081930.3939106-1-zhengyejian1@huawei.com Cc: <mhiramat@kernel.org> Signed-off-by: Zheng Yejian <zhengyejian1@huawei.com> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Zheng Yejian authored
[ Upstream commit f4e4ada5 ] Function instance_set() expects to enable event 'sched_switch', so we should set 1 to its 'enable' file. Testcase passed after this patch: # ./ftracetest test.d/instances/instance-event.tc === Ftrace unit tests === [1] Test creation and deletion of trace instances while setting an event [PASS] # of passed: 1 # of failed: 0 # of unresolved: 0 # of untested: 0 # of unsupported: 0 # of xfailed: 0 # of undefined(test bug): 0 Signed-off-by: Zheng Yejian <zhengyejian1@huawei.com> Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Acked-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Shuah Khan <skhan@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Kiwoong Kim authored
[ Upstream commit d32533d3 ] With auto hibern8 enabled, UIC could be busy processing a hibern8 operation and the HCI would reports UIC not ready for a short while through HCS.UCRDY. The UFS driver doesn't currently handle this situation. The UFSHCI spec specifies UCRDY like this: whether the host controller is ready to process UIC COMMAND The 'ready' could be seen as many different meanings. If the meaning includes not processing any request from HCI, processing a hibern8 operation can be 'not ready'. In this situation, the driver needs to wait until the operations is completed. Signed-off-by: Kiwoong Kim <kwmad.kim@samsung.com> Link: https://lore.kernel.org/r/550484ffb66300bdcec63d3e304dfd55cb432f1f.1693790060.git.kwmad.kim@samsung.com Reviewed-by: Adrian Hunter <adrian.hunter@intel.com> Reviewed-by: Chanwoo Lee <cw9316.lee@samsung.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Kiwoong Kim authored
[ Upstream commit 2d3f59cf ] __ufshcd_send_uic_cmd() is wrapped by uic_cmd_mutex and its related contexts are accessed within the section wrapped by uic_cmd_mutex. Thus, wrapping with host_lock is redundant. Signed-off-by: Kiwoong Kim <kwmad.kim@samsung.com> Link: https://lore.kernel.org/r/782ba5f26f0a96e58d85dff50751787d2d2a6b2b.1693790060.git.kwmad.kim@samsung.com Reviewed-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Chanwoo Lee <cw9316.lee@samsung.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Javed Hasan authored
[ Upstream commit 7df0b260 ] Avoid race condition between I/O completion and abort processing by protecting the cmd_type with the rport lock. Signed-off-by: Javed Hasan <jhasan@marvell.com> Signed-off-by: Saurav Kashyap <skashyap@marvell.com> Link: https://lore.kernel.org/r/20230901060646.27885-1-skashyap@marvell.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Helge Deller authored
[ Upstream commit b1bef138 ] Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Helge Deller authored
[ Upstream commit b137b9d6 ] Fix "warning: directive in macro's argument list" warning. Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Helge Deller authored
[ Upstream commit 927c6c8a ] Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Helge Deller authored
[ Upstream commit eb3255ee ] Fix this makecheck warning: drivers/parisc/sba_iommu.c:98:19: warning: symbol 'sba_list' was not declared. Should it be static? Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Nigel Kirkland authored
[ Upstream commit 8ae5b3a6 ] The nvme_fc_fcp_op structure describing an AEN operation is initialized with a null request structure pointer. An FC LLDD may make a call to nvme_fc_io_getuuid passing a pointer to an nvmefc_fcp_req for an AEN operation. Add validation of the request structure pointer before dereference. Signed-off-by: Nigel Kirkland <nkirkland2304@gmail.com> Reviewed-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Tobias Schramm authored
[ Upstream commit 1f11f420 ] Previously the transfer complete IRQ immediately drained to RX FIFO to read any data remaining in FIFO to the RX buffer. This behaviour is correct when dealing with SPI in interrupt mode. However in DMA mode the transfer complete interrupt still fires as soon as all bytes to be transferred have been stored in the FIFO. At that point data in the FIFO still needs to be picked up by the DMA engine. Thus the drain procedure and DMA engine end up racing to read from RX FIFO, corrupting any data read. Additionally the RX buffer pointer is never adjusted according to DMA progress in DMA mode, thus calling the RX FIFO drain procedure in DMA mode is a bug. Fix corruptions in DMA RX mode by draining RX FIFO only in interrupt mode. Also wait for completion of RX DMA when in DMA mode before returning to ensure all data has been copied to the supplied memory buffer. Signed-off-by: Tobias Schramm <t.schramm@manjaro.org> Link: https://lore.kernel.org/r/20230827152558.5368-3-t.schramm@manjaro.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Tobias Schramm authored
[ Upstream commit 171f8a49 ] Through empirical testing it has been determined that sometimes RX SPI transfers with DMA enabled return corrupted data. This is down to single or even multiple bytes lost during DMA transfer from SPI peripheral to memory. It seems the RX FIFO within the SPI peripheral can become confused when performing bus read accesses wider than a single byte to it during an active SPI transfer. This patch reduces the width of individual DMA read accesses to the RX FIFO to a single byte to mitigate that issue. Signed-off-by: Tobias Schramm <t.schramm@manjaro.org> Link: https://lore.kernel.org/r/20230827152558.5368-2-t.schramm@manjaro.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Daniel Borkmann authored
[ Upstream commit 6a86b5b5 ] syzbot reported a data race splat between two processes trying to update the same BPF map value via syscall on different CPUs: BUG: KCSAN: data-race in bpf_percpu_array_update / bpf_percpu_array_update write to 0xffffe8fffe7425d8 of 8 bytes by task 8257 on cpu 1: bpf_long_memcpy include/linux/bpf.h:428 [inline] bpf_obj_memcpy include/linux/bpf.h:441 [inline] copy_map_value_long include/linux/bpf.h:464 [inline] bpf_percpu_array_update+0x3bb/0x500 kernel/bpf/arraymap.c:380 bpf_map_update_value+0x190/0x370 kernel/bpf/syscall.c:175 generic_map_update_batch+0x3ae/0x4f0 kernel/bpf/syscall.c:1749 bpf_map_do_batch+0x2df/0x3d0 kernel/bpf/syscall.c:4648 __sys_bpf+0x28a/0x780 __do_sys_bpf kernel/bpf/syscall.c:5241 [inline] __se_sys_bpf kernel/bpf/syscall.c:5239 [inline] __x64_sys_bpf+0x43/0x50 kernel/bpf/syscall.c:5239 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x63/0xcd write to 0xffffe8fffe7425d8 of 8 bytes by task 8268 on cpu 0: bpf_long_memcpy include/linux/bpf.h:428 [inline] bpf_obj_memcpy include/linux/bpf.h:441 [inline] copy_map_value_long include/linux/bpf.h:464 [inline] bpf_percpu_array_update+0x3bb/0x500 kernel/bpf/arraymap.c:380 bpf_map_update_value+0x190/0x370 kernel/bpf/syscall.c:175 generic_map_update_batch+0x3ae/0x4f0 kernel/bpf/syscall.c:1749 bpf_map_do_batch+0x2df/0x3d0 kernel/bpf/syscall.c:4648 __sys_bpf+0x28a/0x780 __do_sys_bpf kernel/bpf/syscall.c:5241 [inline] __se_sys_bpf kernel/bpf/syscall.c:5239 [inline] __x64_sys_bpf+0x43/0x50 kernel/bpf/syscall.c:5239 do_syscall_x64 arch/x86/entry/common.c:50 [inline] do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80 entry_SYSCALL_64_after_hwframe+0x63/0xcd value changed: 0x0000000000000000 -> 0xfffffff000002788 The bpf_long_memcpy is used with 8-byte aligned pointers, power-of-8 size and forced to use long read/writes to try to atomically copy long counters. It is best-effort only and no barriers are here since it _will_ race with concurrent updates from BPF programs. The bpf_long_memcpy() is called from bpf(2) syscall. Marco suggested that the best way to make this known to KCSAN would be to use data_race() annotation. Reported-by: <syzbot+97522333291430dd277f@syzkaller.appspotmail.com> Suggested-by: Marco Elver <elver@google.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Marco Elver <elver@google.com> Link: https://lore.kernel.org/bpf/000000000000d87a7f06040c970c@google.com Link: https://lore.kernel.org/bpf/57628f7a15e20d502247c3b55fceb1cb2b31f266.1693342186.git.daniel@iogearbox.net Signed-off-by: Sasha Levin <sashal@kernel.org>
-
Sergey Senozhatsky authored
[ Upstream commit fb5a4315 ] __dma_entry_alloc_check_leak() calls into printk -> serial console output (qcom geni) and grabs port->lock under free_entries_lock spin lock, which is a reverse locking dependency chain as qcom_geni IRQ handler can call into dma-debug code and grab free_entries_lock under port->lock. Move __dma_entry_alloc_check_leak() call out of free_entries_lock scope so that we don't acquire serial console's port->lock under it. Trimmed-down lockdep splat: The existing dependency chain (in reverse order) is: -> #2 (free_entries_lock){-.-.}-{2:2}: _raw_spin_lock_irqsave+0x60/0x80 dma_entry_alloc+0x38/0x110 debug_dma_map_page+0x60/0xf8 dma_map_page_attrs+0x1e0/0x230 dma_map_single_attrs.constprop.0+0x6c/0xc8 geni_se_rx_dma_prep+0x40/0xcc qcom_geni_serial_isr+0x310/0x510 __handle_irq_event_percpu+0x110/0x244 handle_irq_event_percpu+0x20/0x54 handle_irq_event+0x50/0x88 handle_fasteoi_irq+0xa4/0xcc handle_irq_desc+0x28/0x40 generic_handle_domain_irq+0x24/0x30 gic_handle_irq+0xc4/0x148 do_interrupt_handler+0xa4/0xb0 el1_interrupt+0x34/0x64 el1h_64_irq_handler+0x18/0x24 el1h_64_irq+0x64/0x68 arch_local_irq_enable+0x4/0x8 ____do_softirq+0x18/0x24 ... -> #1 (&port_lock_key){-.-.}-{2:2}: _raw_spin_lock_irqsave+0x60/0x80 qcom_geni_serial_console_write+0x184/0x1dc console_flush_all+0x344/0x454 console_unlock+0x94/0xf0 vprintk_emit+0x238/0x24c vprintk_default+0x3c/0x48 vprintk+0xb4/0xbc _printk+0x68/0x90 register_console+0x230/0x38c uart_add_one_port+0x338/0x494 qcom_geni_serial_probe+0x390/0x424 platform_probe+0x70/0xc0 really_probe+0x148/0x280 __driver_probe_device+0xfc/0x114 driver_probe_device+0x44/0x100 __device_attach_driver+0x64/0xdc bus_for_each_drv+0xb0/0xd8 __device_attach+0xe4/0x140 device_initial_probe+0x1c/0x28 bus_probe_device+0x44/0xb0 device_add+0x538/0x668 of_device_add+0x44/0x50 of_platform_device_create_pdata+0x94/0xc8 of_platform_bus_create+0x270/0x304 of_platform_populate+0xac/0xc4 devm_of_platform_populate+0x60/0xac geni_se_probe+0x154/0x160 platform_probe+0x70/0xc0 ... -> #0 (console_owner){-...}-{0:0}: __lock_acquire+0xdf8/0x109c lock_acquire+0x234/0x284 console_flush_all+0x330/0x454 console_unlock+0x94/0xf0 vprintk_emit+0x238/0x24c vprintk_default+0x3c/0x48 vprintk+0xb4/0xbc _printk+0x68/0x90 dma_entry_alloc+0xb4/0x110 debug_dma_map_sg+0xdc/0x2f8 __dma_map_sg_attrs+0xac/0xe4 dma_map_sgtable+0x30/0x4c get_pages+0x1d4/0x1e4 [msm] msm_gem_pin_pages_locked+0x38/0xac [msm] msm_gem_pin_vma_locked+0x58/0x88 [msm] msm_ioctl_gem_submit+0xde4/0x13ac [msm] drm_ioctl_kernel+0xe0/0x15c drm_ioctl+0x2e8/0x3f4 vfs_ioctl+0x30/0x50 ... Chain exists of: console_owner --> &port_lock_key --> free_entries_lock Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(free_entries_lock); lock(&port_lock_key); lock(free_entries_lock); lock(console_owner); *** DEADLOCK *** Call trace: dump_backtrace+0xb4/0xf0 show_stack+0x20/0x30 dump_stack_lvl+0x60/0x84 dump_stack+0x18/0x24 print_circular_bug+0x1cc/0x234 check_noncircular+0x78/0xac __lock_acquire+0xdf8/0x109c lock_acquire+0x234/0x284 console_flush_all+0x330/0x454 console_unlock+0x94/0xf0 vprintk_emit+0x238/0x24c vprintk_default+0x3c/0x48 vprintk+0xb4/0xbc _printk+0x68/0x90 dma_entry_alloc+0xb4/0x110 debug_dma_map_sg+0xdc/0x2f8 __dma_map_sg_attrs+0xac/0xe4 dma_map_sgtable+0x30/0x4c get_pages+0x1d4/0x1e4 [msm] msm_gem_pin_pages_locked+0x38/0xac [msm] msm_gem_pin_vma_locked+0x58/0x88 [msm] msm_ioctl_gem_submit+0xde4/0x13ac [msm] drm_ioctl_kernel+0xe0/0x15c drm_ioctl+0x2e8/0x3f4 vfs_ioctl+0x30/0x50 ... Reported-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org> Acked-by: Robin Murphy <robin.murphy@arm.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
-