- May 23, 2018
-
-
Theodore Ts'o authored
[ Upstream commit 18db4b4e ] If some metadata block, such as an allocation bitmap, overlaps the superblock, it's very likely that if the file system is mounted read/write, the results will not be pretty. So disallow r/w mounts for file systems corrupted in this particular way. Signed-off-by: Theodore Ts'o <tytso@mit.edu> Cc: stable@vger.kernel.org Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
-
Alex Williamson authored
[ Upstream commit cf0d53ba ] MRRS defines the maximum read request size a device is allowed to make. Drivers will often increase this to allow more data transfer with a single request. Completions to this request are bound by the MPS setting for the bus. Aside from device quirks (none known), it doesn't seem to make sense to set an MRRS value less than MPS, yet this is a likely scenario given that user drivers do not have a system-wide view of the PCI topology. Virtualize MRRS such that the user can set MRRS >= MPS, but use MPS as the floor value that we'll write to hardware. Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
-
Alex Williamson authored
[ Upstream commit 52318497 ] With virtual PCI-Express chipsets, we now see userspace/guest drivers trying to match the physical MPS setting to a virtual downstream port. Of course a lone physical device surrounded by virtual interconnects cannot make a correct decision for a proper MPS setting. Instead, let's virtualize the MPS control register so that writes through to hardware are disallowed. Userspace drivers like QEMU assume they can write anything to the device and we'll filter out anything dangerous. Since mismatched MPS can lead to AER and other faults, let's add it to the kernel side rather than relying on userspace virtualization to handle it. Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Reviewed-by: Eric Auger <eric.auger@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
-
Alex Williamson authored
[ Upstream commit ddf9dc0e ] We use a BAR restore trick to try to detect when a user has performed a device reset, possibly through FLR or other backdoors, to put things back into a working state. This is important for backdoor resets, but we can actually just virtualize the "front door" resets provided via PCIe and AF FLR. Set these bits as virtualized + writable, allowing the default write to set them in vconfig, then we can simply check the bit, perform an FLR of our own, and clear the bit. We don't actually have the granularity in PCI to specify the type of reset we want to do, but generally devices don't implement both PCIe and AF FLR and we'll favor these over other types of reset, so we should generally lineup. We do test whether the device provides the requested FLR type to stay consistent with hardware capabilities though. This seems to fix several instance of devices getting into bad states with userspace drivers, like dpdk, running inside a VM. Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Reviewed-by: Greg Rose <grose@lightfleet.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
-
Takashi Iwai authored
[ Upstream commit e15dc99d ] The commit 02a5d692 ("ALSA: pcm: Avoid potential races between OSS ioctls and read/write") split the PCM preparation code to a locked version, and it added a sanity check of runtime->oss.prepare flag along with the change. This leaded to an endless loop when the stream gets XRUN: namely, snd_pcm_oss_write3() and co call snd_pcm_oss_prepare() without setting runtime->oss.prepare flag and the loop continues until the PCM state reaches to another one. As the function is supposed to execute the preparation unconditionally, drop the invalid state check there. The bug was triggered by syzkaller. Fixes: 02a5d692 ("ALSA: pcm: Avoid potential races between OSS ioctls and read/write") Reported-by: <syzbot+150189c103427d31a053@syzkaller.appspotmail.com> Reported-by: <syzbot+7e3f31a52646f939c052@syzkaller.appspotmail.com> Reported-by: <syzbot+4f2016cf5185da7759dc@syzkaller.appspotmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
-
Takashi Iwai authored
[ Upstream commit f6d297df ] The previous fix 40cab6e8 ("ALSA: pcm: Return -EBUSY for OSS ioctls changing busy streams") introduced some mutex unbalance; the check of runtime->oss.rw_ref was inserted in a wrong place after the mutex lock. This patch fixes the inconsistency by rewriting with the helper functions to lock/unlock parameters with the stream check. Fixes: 40cab6e8 ("ALSA: pcm: Return -EBUSY for OSS ioctls changing busy streams") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
-
Takashi Iwai authored
[ Upstream commit 40cab6e8 ] OSS PCM stream management isn't modal but it allows ioctls issued at any time for changing the parameters. In the previous hardening patch ("ALSA: pcm: Avoid potential races between OSS ioctls and read/write"), we covered these races and prevent the corruption by protecting the concurrent accesses via params_lock mutex. However, this means that some ioctls that try to change the stream parameter (e.g. channels or format) would be blocked until the read/write finishes, and it may take really long. Basically changing the parameter while reading/writing is an invalid operation, hence it's even more user-friendly from the API POV if it returns -EBUSY in such a situation. This patch adds such checks in the relevant ioctls with the addition of read/write access refcount. Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
-
Takashi Iwai authored
[ Upstream commit 02a5d692 ] Although we apply the params_lock mutex to the whole read and write operations as well as snd_pcm_oss_change_params(), we may still face some races. First off, the params_lock is taken inside the read and write loop. This is intentional for avoiding the too long locking, but it allows the in-between parameter change, which might lead to invalid pointers. We check the readiness of the stream and set up via snd_pcm_oss_make_ready() at the beginning of read and write, but it's called only once, by assuming that it remains ready in the rest. Second, many ioctls that may change the actual parameters (i.e. setting runtime->oss.params=1) aren't protected, hence they can be processed in a half-baked state. This patch is an attempt to plug these holes. The stream readiness check is moved inside the read/write inner loop, so that the stream is always set up in a proper state before further processing. Also, each ioctl that may change the parameter is wrapped with the params_lock for avoiding the races. The issues were triggered by syzkaller in a few different scenarios, particularly the one below appearing as GPF in loopback_pos_update. Reported-by: <syzbot+c4227aec125487ec3efa@syzkaller.appspotmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
-
Takashi Iwai authored
[ Upstream commit c64ed5dd ] Fix the last standing EINTR in the whole subsystem. Use more correct ERESTARTSYS for pending signals. Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
-
Nicholas Mc Guire authored
[ Upstream commit 46325371 ] This is an API consolidation only. The use of kmalloc + memset to 0 is equivalent to kzalloc. Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
-
Igor Pylypiv authored
[ Upstream commit 977f6f68 ] F71808FG_FLAG_WD_EN defines bit position, not a bitmask Signed-off-by: Igor Pylypiv <igor.pylypiv@gmail.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@iguana.be> Cc: stable <stable@vger.kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
-
Richard Genoud authored
[ Upstream commit 6a4a4595 ] Clearfog boards can come with a CPU clocked at 1600MHz (commercial) or 1333MHz (industrial). They have also some dip-switches to select a different clock (666, 800, 1066, 1200). The funny thing is that the recovery button is on the MPP34 fq selector. So, when booting an industrial board with this button down, the frequency 666MHz is selected (and the kernel didn't boot). This patch add all the missing clocks. The only mode I didn't test is 2GHz (uboot found 4294MHz instead :/ ). Fixes: 0e85aece ("clk: mvebu: add clock support for Armada 380/385") Cc: <stable@vger.kernel.org> # 3.16.x: 9593f4f5 : clk: mvebu: armada-38x: add support for 1866MHz variants Cc: <stable@vger.kernel.org> # 3.16.x Signed-off-by: Richard Genoud <richard.genoud@gmail.com> Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
-
Ralph Sennhauser authored
[ Upstream commit 9593f4f5 ] The Linksys WRT3200ACM CPU is clocked at 1866MHz. Add 1866MHz to the list of supported CPU frequencies. Also update multiplier and divisor for the l2clk and ddrclk. Noticed by the following warning: [ 0.000000] Selected CPU frequency (16) unsupported Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com> Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
-
Alex Smith authored
[ Upstream commit a04f0017 ] A spinlock is held while updating the internal copy of the IRQ mask, but not while writing it to the actual IMASK register. After the lock is released, an IRQ can occur before the IMASK register is written. If handling this IRQ causes the mask to be changed, when the handler returns back to the middle of the first mask update, a stale value will be written to the mask register. If this causes an IRQ to become unmasked that cannot have its status cleared by writing a 1 to it in the IREG register, e.g. the SDIO IRQ, then we can end up stuck with the same IRQ repeatedly being fired but not handled. Normally the MMC IRQ handler attempts to clear any unexpected IRQs by writing IREG, but for those that cannot be cleared in this way then the IRQ will just repeatedly fire. This was resulting in lockups after a while of using Wi-Fi on the CI20 (GitHub issue #19). Resolve by holding the spinlock until after the IMASK register has been updated. Cc: stable@vger.kernel.org Link: https://github.com/MIPS/CI20_linux/issues/19 Fixes: 61bfbdb8 ("MMC: Add support for the controller on JZ4740 SoCs.") Tested-by: Mathieu Malaterre <malat@debian.org> Signed-off-by: Alex Smith <alex.smith@imgtec.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
-
Krzysztof Mazur authored
[ Upstream commit 4d1a535b ] glibc 2.26 removed the 'struct ucontext' to "improve" POSIX compliance and break programs, including User Mode Linux. Fix User Mode Linux by using POSIX ucontext_t. This fixes: arch/um/os-Linux/signal.c: In function 'hard_handler': arch/um/os-Linux/signal.c:163:22: error: dereferencing pointer to incomplete type 'struct ucontext' mcontext_t *mc = &uc->uc_mcontext; arch/x86/um/stub_segv.c: In function 'stub_segv_handler': arch/x86/um/stub_segv.c:16:13: error: dereferencing pointer to incomplete type 'struct ucontext' &uc->uc_mcontext); Cc: stable@vger.kernel.org Signed-off-by: Krzysztof Mazur <krzysiek@podlesie.net> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
-
Maxime Jayat authored
[ Upstream commit c5637476 ] Despite the efforts made to correctly read the NDA and CUBC registers, the order in which the registers are read could sometimes lead to an inconsistent state. Re-using the timeline from the comments, this following timing of registers reads could lead to reading NDA with value "@desc2" and CUBC with value "MAX desc1": INITD -------- ------------ |____________________| _______________________ _______________ NDA @desc2 \/ @desc3 _______________________/\_______________ __________ ___________ _______________ CUBC 0 \/ MAX desc1 \/ MAX desc2 __________/\___________/\_______________ | | | | Events:(1)(2) (3)(4) (1) check_nda = @desc2 (2) initd = 1 (3) cur_ubc = MAX desc1 (4) cur_nda = @desc2 This is allowed by the condition ((check_nda == cur_nda) && initd), despite cur_ubc and cur_nda being in the precise state we don't want. This error leads to incorrect residue computation. Fix it by inversing the order in which CUBC and INITD are read. This makes sure that NDA and CUBC are always read together either _before_ INITD goes to 0 or _after_ it is back at 1. The case where NDA is read before INITD is at 0 and CUBC is read after INITD is back at 1 will be rejected by check_nda and cur_nda being different. Fixes: 53398f48 ("dmaengine: at_xdmac: fix residue corruption") Cc: stable@vger.kernel.org Signed-off-by: Maxime Jayat <maxime.jayat@mobile-devices.fr> Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
-
Bart Van Assche authored
[ Upstream commit 3a148896 ] Ensure that cv_end is equal to ibdev->num_comp_vectors for the NUMA node with the highest index. This patch improves spreading of RDMA channels over completion vectors and thereby improves performance, especially on systems with only a single NUMA node. This patch drops support for the comp_vector login parameter by ignoring the value of that parameter since I have not found a good way to combine support for that parameter and automatic spreading of RDMA channels over completion vectors. Fixes: d92c0da7 ("IB/srp: Add multichannel support") Reported-by: Alexander Schmid <alex@modula-shop-systems.de> Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com> Cc: Alexander Schmid <alex@modula-shop-systems.de> Cc: stable@vger.kernel.org Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
-
Bart Van Assche authored
[ Upstream commit e68088e7 ] Before commit e494f6a7 ("[SCSI] improved eh timeout handler") it did not really matter whether or not abort handlers like srp_abort() called .scsi_done() when returning another value than SUCCESS. Since that commit however this matters. Hence only call .scsi_done() when returning SUCCESS. Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com> Cc: stable@vger.kernel.org Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
-
Roland Dreier authored
[ Upstream commit 8435168d ] Check to make sure that ctx->cm_id->device is set before we use it. Otherwise userspace can trigger a NULL dereference by doing RDMA_USER_CM_CMD_SET_OPTION on an ID that is not bound to a device. Cc: <stable@vger.kernel.org> Reported-by: <syzbot+a67bc93e14682d92fc2f@syzkaller.appspotmail.com> Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
-
Theodore Ts'o authored
[ Upstream commit 85e0c4e8 ] This updates the jbd2 superblock unnecessarily, and on an abort we shouldn't truncate the log. Signed-off-by: Theodore Ts'o <tytso@mit.edu> Cc: stable@vger.kernel.org Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
-
Theodore Ts'o authored
[ Upstream commit 9f886f4d ] This fixes a harmless UBSAN where root could potentially end up causing an overflow while bumping the entropy_total field (which is ignored once the entropy pool has been initialized, and this generally is completed during the boot sequence). This is marginal for the stable kernel series, but it's a really trivial patch, and it fixes UBSAN warning that might cause security folks to get overly excited for no reason. Signed-off-by: Theodore Ts'o <tytso@mit.edu> Reported-by: Chen Feng <puck.chen@hisilicon.com> Cc: stable@vger.kernel.org Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
-
Mika Westerberg authored
[ Upstream commit f2a659f7 ] The driver misses implementation of PM hook that undoes what ->freeze_noirq() does after the hibernation image is created. This means the control channel is not resumed properly and the Thunderbolt bus becomes useless in later stages of hibernation (when the image is stored or if the operation fails). Fix this by pointing ->thaw_noirq to driver nhi_resume_noirq(). This makes sure the control channel is resumed properly. Fixes: 23dd5bb4 ("thunderbolt: Add suspend/hibernate support") Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
-
James Kelly authored
[ Upstream commit a01df75c ] SSM2602 driver is broken on recent kernels (at least since 4.9). User space applications such as amixer or alsamixer get EIO when attempting to access codec controls via the relevant IOCTLs. Root cause of these failures is the regcache_hw_init function in drivers/base/regmap/regcache.c, which prevents regmap cache initalization from the reg_defaults_raw element of the regmap_config structure when registers are write only. It also disables the regmap cache entirely when all registers are write only or volatile as is the case for the SSM2602 driver. Using the reg_defaults element of the regmap_config structure rather than the reg_defaults_raw element to initalize the regmap cache avoids the logic in the regcache_hw_init function entirely. It also makes this driver consistent with other ASoC codec drivers, as this driver was the ONLY codec driver that used the reg_defaults_raw element to initalize the cache. Tested on Digilent Zybo Z7 development board which has a SSM2603 codec chip connected to a Xilinx Zynq SoC. Signed-off-by: James Kelly <jamespeterkelly@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
-
Aaron Ma authored
[ Upstream commit 6de0b13c ] When size is negative, calling memset will make segment fault. Declare the size as type u32 to keep memset safe. size in struct hid_report is unsigned, fix return type of hid_report_len to u32. Cc: stable@vger.kernel.org Signed-off-by: Aaron Ma <aaron.ma@canonical.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
-
Nicholas Piggin authored
[ Upstream commit 3b807033 ] The OPAL NVRAM driver does not sleep in case it gets OPAL_BUSY or OPAL_BUSY_EVENT from firmware, which causes large scheduling latencies, and various lockup errors to trigger (again, BMC reboot can cause it). Fix this by converting it to the standard form OPAL_BUSY loop that sleeps. Fixes: 628daa8d ("powerpc/powernv: Add RTC and NVRAM support plus RTAS fallbacks") Depends-on: 34dd25de ("powerpc/powernv: define a standard delay for OPAL_BUSY type retry loops") Cc: stable@vger.kernel.org # v3.2+ Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
-
Nicholas Piggin authored
[ Upstream commit 34dd25de ] This is the start of an effort to tidy up and standardise all the delays. Existing loops have a range of delay/sleep periods from 1ms to 20ms, and some have no delay. They all loop forever except rtc, which times out after 10 retries, and that uses 10ms delays. So use 10ms as our standard delay. The OPAL maintainer agrees 10ms is a reasonable starting point. The idea is to use the same recipe everywhere, once this is proven to work then it will be documented as an OPAL API standard. Then both firmware and OS can agree, and if a particular call needs something else, then that can be documented with reasoning. This is not the end-all of this effort, it's just a relatively easy change that fixes some existing high latency delays. There should be provision for standardising timeouts and/or interruptible loops where possible, so non-fatal firmware errors don't cause hangs. Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
-
Nicholas Piggin authored
[ Upstream commit 0bfdf598 ] asm/barrier.h is not always included after asm/synch.h, which meant it was missing __SUBARCH_HAS_LWSYNC, so in some files smp_wmb() would be eieio when it should be lwsync. kernel/time/hrtimer.c is one case. __SUBARCH_HAS_LWSYNC is only used in one place, so just fold it in to where it's used. Previously with my small simulator config, 377 instances of eieio in the tree. After this patch there are 55. Fixes: 46d075be ("powerpc: Optimise smp_wmb") Cc: stable@vger.kernel.org # v2.6.29+ Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
-
Nicholas Piggin authored
[ Upstream commit 741de617 ] opal_nvram_write currently just assumes success if it encounters an error other than OPAL_BUSY or OPAL_BUSY_EVENT. Have it return -EIO on other errors instead. Fixes: 628daa8d ("powerpc/powernv: Add RTC and NVRAM support plus RTAS fallbacks") Cc: stable@vger.kernel.org # v3.2+ Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Reviewed-by: Vasant Hegde <hegdevasant@linux.vnet.ibm.com> Acked-by: Stewart Smith <stewart@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
-
Aaron Ma authored
[ Upstream commit ac75a041 ] When convert char array with signed int, if the inbuf[x] is negative then upper bits will be set to 1. Fix this by using u8 instead of char. ret_size has to be at least 3, hid_input_report use it after minus 2 bytes. Cc: stable@vger.kernel.org Signed-off-by: Aaron Ma <aaron.ma@canonical.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
-
Thinh Nguyen authored
[ Upstream commit cabdf83d ] Platform device is allocated before adding resources. Make sure to properly cleanup on error case. Cc: <stable@vger.kernel.org> Fixes: f1c7e710 ("usb: dwc3: convert to pcim_enable_device()") Signed-off-by: Thinh Nguyen <thinhn@synopsys.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
-
Zhengjun Xing authored
[ Upstream commit 64627388 ] USB3 hubs don't support global suspend. USB3 specification 10.10, Enhanced SuperSpeed hubs only support selective suspend and resume, they do not support global suspend/resume where the hub downstream facing ports states are not affected. When system enters hibernation it first enters freeze process where only the root hub enters suspend, usb_port_suspend() is not called for other devices, and suspend status flags are not set for them. Other devices are expected to suspend globally. Some external USB3 hubs will suspend the downstream facing port at global suspend. These devices won't be resumed at thaw as the suspend status flag is not set. A USB3 removable hard disk connected through a USB3 hub that won't resume at thaw will fail to synchronize SCSI cache, return “cmd cmplt err -71” error, and needs a 60 seconds timeout which causing system hang for 60s before the USB host reset the port for the USB3 removable hard disk to recover. Fix this by always calling usb_port_suspend() during freeze for USB3 devices. Signed-off-by: Zhengjun Xing <zhengjun.xing@linux.intel.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
-
Mika Westerberg authored
[ Upstream commit 13d3047c ] Mike Lothian reported that plugging in a USB-C device does not work properly in his Dell Alienware system. This system has an Intel Alpine Ridge Thunderbolt controller providing USB-C functionality. In these systems the USB controller (xHCI) is hotplugged whenever a device is connected to the port using ACPI-based hotplug. The ACPI description of the root port in question is as follows: Device (RP01) { Name (_ADR, 0x001C0000) Device (PXSX) { Name (_ADR, 0x02) Method (_RMV, 0, NotSerialized) { // ... } } Here _ADR 0x02 means device 0, function 2 on the bus under root port (RP01) but that seems to be incorrect because device 0 is the upstream port of the Alpine Ridge PCIe switch and it has no functions other than 0 (the bridge itself). When we get ACPI Notify() to the root port resulting from connecting a USB-C device, Linux tries to read PCI_VENDOR_ID from device 0, function 2 which of course always returns 0xffffffff because there is no such function and we never find the device. In Windows this works fine. Now, since we get ACPI Notify() to the root port and not to the PXSX device we should actually start our scan from there as well and not from the non-existent PXSX device. Fix this by checking presence of the slot itself (function 0) if we fail to do that otherwise. While there use pci_bus_read_dev_vendor_id() in get_slot_status(), which is the recommended way to read Device and Vendor IDs of devices on PCI buses. Link: https://bugzilla.kernel.org/show_bug.cgi?id=198557 Reported-by: Mike Lothian <mike@fireburn.co.uk> Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: stable@vger.kernel.org Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
-
Jason Andryuk authored
[ Upstream commit c2d2e673 ] A toolstack may delete the vif frontend and backend xenstore entries while xen-netfront is in the removal code path. In that case, the checks for xenbus_read_driver_state would return XenbusStateUnknown, and xennet_remove would hang indefinitely. This hang prevents system shutdown. xennet_remove must be able to handle XenbusStateUnknown, and netback_changed must also wake up the wake_queue for that state as well. Fixes: 5b5971df ("xen-netfront: remove warning when unloading module") Signed-off-by: Jason Andryuk <jandryuk@gmail.com> Cc: Eduardo Otubo <otubo@redhat.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
-
Nicolas Ferre authored
[ Upstream commit e8fd0adf ] There are only 19 PIOB pins having primary names PB0-PB18. Not all of them have a 'C' function. So the pinctrl property mask ends up being the same as the other SoC of the at91sam9x5 series. Reported-by: Marek Sieranski <marek.sieranski@microchip.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> Cc: <stable@vger.kernel.org> # v3.8+ Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
-
Heinrich Schuchardt authored
[ Upstream commit af6f8529 ] musb->endpoints[] has array size MUSB_C_NUM_EPS. We must check array bounds before accessing the array and not afterwards. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: Bin Liu <b-liu@ti.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
-
Eric Biggers authored
[ Upstream commit 3f05317d ] syzbot reported a use-after-free of shm_file_data(file)->file->f_op in shm_get_unmapped_area(), called via sys_remap_file_pages(). Unfortunately it couldn't generate a reproducer, but I found a bug which I think caused it. When remap_file_pages() is passed a full System V shared memory segment, the memory is first unmapped, then a new map is created using the ->vm_file. Between these steps, the shm ID can be removed and reused for a new shm segment. But, shm_mmap() only checks whether the ID is currently valid before calling the underlying file's ->mmap(); it doesn't check whether it was reused. Thus it can use the wrong underlying file, one that was already freed. Fix this by making the "outer" shm file (the one that gets put in ->vm_file) hold a reference to the real shm file, and by making __shm_open() require that the file associated with the shm ID matches the one associated with the "outer" file. Taking the reference to the real shm file is needed to fully solve the problem, since otherwise sfd->file could point to a freed file, which then could be reallocated for the reused shm ID, causing the wrong shm segment to be mapped (and without the required permission checks). Commit 1ac0b6de ("ipc/shm: handle removed segments gracefully in shm_mmap()") almost fixed this bug, but it didn't go far enough because it didn't consider the case where the shm ID is reused. The following program usually reproduces this bug: #include <stdlib.h> #include <sys/shm.h> #include <sys/syscall.h> #include <unistd.h> int main() { int is_parent = (fork() != 0); srand(getpid()); for (;;) { int id = shmget(0xF00F, 4096, IPC_CREAT|0700); if (is_parent) { void *addr = shmat(id, NULL, 0); usleep(rand() % 50); while (!syscall(__NR_remap_file_pages, addr, 4096, 0, 0, 0)); } else { usleep(rand() % 50); shmctl(id, IPC_RMID, NULL); } } } It causes the following NULL pointer dereference due to a 'struct file' being used while it's being freed. (I couldn't actually get a KASAN use-after-free splat like in the syzbot report. But I think it's possible with this bug; it would just take a more extraordinary race...) BUG: unable to handle kernel NULL pointer dereference at 0000000000000058 PGD 0 P4D 0 Oops: 0000 [#1] SMP NOPTI CPU: 9 PID: 258 Comm: syz_ipc Not tainted 4.16.0-05140-gf8cf2f16a7c95 #189 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.0-20171110_100015-anatol 04/01/2014 RIP: 0010:d_inode include/linux/dcache.h:519 [inline] RIP: 0010:touch_atime+0x25/0xd0 fs/inode.c:1724 [...] Call Trace: file_accessed include/linux/fs.h:2063 [inline] shmem_mmap+0x25/0x40 mm/shmem.c:2149 call_mmap include/linux/fs.h:1789 [inline] shm_mmap+0x34/0x80 ipc/shm.c:465 call_mmap include/linux/fs.h:1789 [inline] mmap_region+0x309/0x5b0 mm/mmap.c:1712 do_mmap+0x294/0x4a0 mm/mmap.c:1483 do_mmap_pgoff include/linux/mm.h:2235 [inline] SYSC_remap_file_pages mm/mmap.c:2853 [inline] SyS_remap_file_pages+0x232/0x310 mm/mmap.c:2769 do_syscall_64+0x64/0x1a0 arch/x86/entry/common.c:287 entry_SYSCALL_64_after_hwframe+0x42/0xb7 [ebiggers@google.com: add comment] Link: http://lkml.kernel.org/r/20180410192850.235835-1-ebiggers3@gmail.com Link: http://lkml.kernel.org/r/20180409043039.28915-1-ebiggers3@gmail.com Reported-by: <syzbot+d11f321e7f1923157eac80aa990b446596f46439@syzkaller.appspotmail.com> Fixes: c8d78c18 ("mm: replace remap_file_pages() syscall with emulation") Signed-off-by: Eric Biggers <ebiggers@google.com> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Acked-by: Davidlohr Bueso <dbueso@suse.de> Cc: Manfred Spraul <manfred@colorfullife.com> Cc: "Eric W . Biederman" <ebiederm@xmission.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
-
Takashi Iwai authored
[ Upstream commit 60bb83b8 ] We've got a bug report indicating a kernel panic at booting on an x86-32 system, and it turned out to be the invalid PCI resource assigned after reallocation. __find_resource() first aligns the resource start address and resets the end address with start+size-1 accordingly, then checks whether it's contained. Here the end address may overflow the integer, although resource_contains() still returns true because the function validates only start and end address. So this ends up with returning an invalid resource (start > end). There was already an attempt to cover such a problem in the commit 47ea91b4 ("Resource: fix wrong resource window calculation"), but this case is an overseen one. This patch adds the validity check of the newly calculated resource for avoiding the integer overflow problem. Bugzilla: http://bugzilla.opensuse.org/show_bug.cgi?id=1086739 Link: http://lkml.kernel.org/r/s5hpo37d5l8.wl-tiwai@suse.de Fixes: 23c570a6 ("resource: ability to resize an allocated resource") Signed-off-by: Takashi Iwai <tiwai@suse.de> Reported-by: Michael Henders <hendersm@shaw.ca> Tested-by: Michael Henders <hendersm@shaw.ca> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Ram Pai <linuxram@us.ibm.com> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
-
Andrew Morton authored
[ Upstream commit 9ad553ab ] One use of the reiserfs_warning() macro in journal_init_dev() is missing a parameter, causing the following warning: REISERFS warning (device loop0): journal_init_dev: Cannot open '%s': %i journal_init_dev: This also causes a WARN_ONCE() warning in the vsprintf code, and then a panic if panic_on_warn is set. Please remove unsupported %/ in format string WARNING: CPU: 1 PID: 4480 at lib/vsprintf.c:2138 format_decode+0x77f/0x830 lib/vsprintf.c:2138 Kernel panic - not syncing: panic_on_warn set ... Just add another string argument to the macro invocation. Addresses https://syzkaller.appspot.com/bug?id=0627d4551fdc39bf1ef5d82cd9eef587047f7718 Link: http://lkml.kernel.org/r/d678ebe1-6f54-8090-df4c-b9affad62293@infradead.org Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: <syzbot+6bd77b88c1977c03f584@syzkaller.appspotmail.com> Tested-by: Randy Dunlap <rdunlap@infradead.org> Acked-by: Jeff Mahoney <jeffm@suse.com> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Jan Kara <jack@suse.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
-
Richard Weinberger authored
[ Upstream commit b5094b7f ] While UBI and UBIFS seem to work at first sight with MLC NAND, you will most likely lose all your data upon a power-cut or due to read/write disturb. In order to protect users from bad surprises, refuse to attach to MLC NAND. Cc: stable@vger.kernel.org Signed-off-by: Richard Weinberger <richard@nod.at> Acked-by: Boris Brezillon <boris.brezillon@bootlin.com> Acked-by: Artem Bityutskiy <dedekind1@gmail.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
-
Romain Izard authored
[ Upstream commit 78a8dfba ] When opening a device with write access, ubiblock_open returns an error code. Currently, this error code is -EPERM, but this is not the right value. The open function for other block devices returns -EROFS when opening read-only devices with FMODE_WRITE set. When used with dm-verity, the veritysetup userspace tool is expecting EROFS, and refuses to use the ubiblock device. Use -EROFS for ubiblock as well. As a result, veritysetup accepts the ubiblock device as valid. Cc: stable@vger.kernel.org Fixes: 9d54c8a3 (UBI: R/O block driver on top of UBI volumes) Signed-off-by: Romain Izard <romain.izard.pro@gmail.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
-