- Add documentation for the Cx/Dx hardware release;
- Fix wrong register offset for retrieving button information;
- Document programming sequence for page register R/W;
- Document a couple of supported gesture IDs.

Signed-off-by: Tai-hwa Liang <avatar@sentelic.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

The Cintiq 24HD has three LEDs on the left side of the tablet and
three LEDs on the right side of the tablet. Switching to LED 0,
1, or 2 will enable the top, middle, or bottom LED for the respective
side. Switching to LED 3 turns off the LEDs on the respective side.

Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Adds support for the Cintiq 24HD. There are two quirks about this
model that haven't been seen in prior tablets. First, a second
touch ring is present on this display; it is being exposed via the
ABS_THROTTLE axis. Second, three capacitive buttons at the top of
the unit are available; though physically a touch strip, we report
the use of these buttons with generic KEY_ events.

Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

This driver adds support for Sharp's GP2AP002A00F proximity sensor. The
proximity is measured as a binary switch, i.e. an object is either
detected or not detected. Hence, this driver is implemented as a switch
that reports SW_FRONT_PROXIMITY.

Reviewed-by: Datta Shubhrajyoti <shubhrajyoti@ti.com>
Signed-off-by: Courtney Cavin <courtney.cavin@sonyericsson.com>
Signed-off-by: Oskar Andero <oskar.andero@sonyericsson.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

These symbols are not used outside it's driver so no need to
make the symbol global.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

This patch converts mc13783-pwrbutton to use the module_platform_driver()
macro which makes the code smaller and a bit simpler.

Also staticise mc13783_pwrbutton_driver which is not used outside
this driver so no need to make the symbol global.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Register input device last so that we do not have to reset
input device pointer after calling input_unregister_device().

Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Having module device table based on PNP id produces the following warning:

  CC      drivers/input/touchscreen/htcpen.o
drivers/input/touchscreen/htcpen.c:50: warning: 'pnp_ids' defined but not used

This happens because it is not a PNP driver, bit rather ISA driver and
pnp_ids table is not used anywhere. To fix this issue let's switch to
DMI-based module table instead,

Reported-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

This variant was introduced in

i2c: boilerplate function for byte swapped smbus_write/read_word_data

This also has the side effect of ensuring any errors from the i2c
read and no longer mangled.

Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Commit 940ab889 introduced a new macro to
save some platform_driver boilerplate code. Use it.

Signed-off-by: JJ Ding <dgdunix@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Commit 940ab889 introduced a new macro to
save some platform_driver boilerplate code. Use it.

Signed-off-by: JJ Ding <dgdunix@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Commit 940ab889 introduced a new macro to
save some platform_driver boilerplate code. Use it.

Signed-off-by: JJ Ding <dgdunix@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Commit 940ab889 introduced a new macro to
save some platform_driver boilerplate code. Use it.

Signed-off-by: JJ Ding <dgdunix@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Commit 940ab889 introduced a new macro to
save some platform_driver boilerplate code. Use it.

Signed-off-by: JJ Ding <dgdunix@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

There exist tilt switches that simply report their tilt-state via
some gpios. The number and orientation of their axes can vary
depending on the switch used and the build of the device. Also two
or more one-axis switches could be combined to provide multi-dimensional
orientation.

One example of a device using such a switch is the family of Qisda
ebook readers, where the switch provides information about the
landscape / portrait orientation of the device. The example in
Documentation/input/gpio-tilt.txt documents exactly this one-axis
device.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

In ancient times it was necessary to manually initialize the bus field of an
spi_driver to spi_bus_type. These days this is done in spi_driver_register(),
so we can drop the manual assignment.

The patch was generated using the following coccinelle semantic patch:
// <smpl>
@@
identifier _driver;
@@
struct spi_driver _driver = {
	.driver = {
-		.bus = &spi_bus_type,
	},
};
// </smpl>

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

MODULE_DEVICE_TABLE will setup the module alias for us, thus adding
MODULE_ALIAS for an entry already in MODULE_DEVICE_TABLE is redundant.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

MODULE_DEVICE_TABLE will setup the module alias for us, thus adding
MODULE_ALIAS for an entry already in MODULE_DEVICE_TABLE is redundant.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

* git://github.com/rustyrussell/linux:
  virtio-pci: make reset operation safer
  virtio-mmio: Correct the name of the guest features selector
  virtio: add HAS_IOMEM dependency to MMIO platform bus driver

virtio pci device reset actually just does an I/O
write, which in PCI is really posted, that is it
can complete on CPU before the device has received it.

Further, interrupts might have been pending on
another CPU, so device callback might get invoked after reset.

This conflicts with how drivers use reset, which is typically:
	reset
	unregister
a callback running after reset completed can race with
unregister, potentially leading to use after free bugs.

Fix by flushing out the write, and flushing pending interrupts.

This assumes that device is never reset from
its vq/config callbacks, or in parallel with being
added/removed, document this assumption.

Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

Guest features selector spelling mistake.

Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: virtualization@lists.linux-foundation.org
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

Fix this compile error on s390:

  CC [M]  drivers/virtio/virtio_mmio.o
drivers/virtio/virtio_mmio.c: In function 'vm_get_features':
drivers/virtio/virtio_mmio.c:107:2: error: implicit declaration of function 'writel'

Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

* 'upstream-linus' of git://github.com/jgarzik/libata-dev:
  libata: fix build without BMDMA
  [libata] ahci_platform: fix DT probing

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci:
  PCI hotplug: shpchp: don't blindly claim non-AMD 0x7450 device IDs
  PCI: pciehp: wait 100 ms after Link Training check
  PCI: pciehp: wait 1000 ms before Link Training check
  PCI: pciehp: Retrieve link speed after link is trained
  PCI: Let PCI_PRI depend on PCI
  PCI: Fix compile errors with PCI_ATS and !PCI_IOV
  PCI / ACPI: Make acpiphp ignore root bridges using PCIe native hotplug

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
  eCryptfs: Extend array bounds for all filename chars
  eCryptfs: Flush file in vma close
  eCryptfs: Prevent file create race condition

From mhalcrow's original commit message:

    Characters with ASCII values greater than the size of
    filename_rev_map[] are valid filename characters.
    ecryptfs_decode_from_filename() will access kernel memory beyond
    that array, and ecryptfs_parse_tag_70_packet() will then decrypt
    those characters. The attacker, using the FNEK of the crafted file,
    can then re-encrypt the characters to reveal the kernel memory past
    the end of the filename_rev_map[] array. I expect low security
    impact since this array is statically allocated in the text area,
    and the amount of memory past the array that is accessible is
    limited by the largest possible ASCII filename character.

This patch solves the issue reported by mhalcrow but with an
implementation suggested by Linus to simply extend the length of
filename_rev_map[] to 256. Characters greater than 0x7A are mapped to
0x00, which is how invalid characters less than 0x7A were previously
being handled.

Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Reported-by: Michael Halcrow <mhalcrow@google.com>
Cc: stable@kernel.org

Dirty pages weren't being written back when an mmap'ed eCryptfs file was
closed before the mapping was unmapped. Since f_ops->flush() is not
called by the munmap() path, the lower file was simply being released.
This patch flushes the eCryptfs file in the vm_ops->close() path.

https://launchpad.net/bugs/870326



Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Cc: stable@kernel.org [2.6.39+]

The file creation path prematurely called d_instantiate() and
unlock_new_inode() before the eCryptfs inode info was fully
allocated and initialized and before the eCryptfs metadata was written
to the lower file.

This could result in race conditions in subsequent file and inode
operations leading to unexpected error conditions or a null pointer
dereference while attempting to use the unallocated memory.

https://launchpad.net/bugs/813146



Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Cc: stable@kernel.org

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest:
  ktest: Check parent options for iterated tests

* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  i2c: Make i2cdev_notifier_call static
  i2c: Delete ANY_I2C_BUS
  i2c: Fix device name for 10-bit slave address
  i2c-algo-bit: Generate correct i2c address sequence for 10-bit target

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
  regulator: TPS65910: Fix VDD1/2 voltage selector count

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (31 commits)
  drm: integer overflow in drm_mode_dirtyfb_ioctl()
  drivers/gpu/vga/vgaarb.c: add missing kfree
  drm/radeon/kms/atom: unify i2c gpio table handling
  drm/radeon/kms: fix up gpio i2c mask bits for r4xx for real
  ttm: Don't return the bo reserved on error path
  drm/radeon/kms: add a CS ioctl flag not to rewrite tiling flags in the CS
  drm/i915: Fix inconsistent backlight level during disabled
  drm, i915: Fix memory leak in i915_gem_busy_ioctl().
  drm/i915: Use DPCD value for max DP lanes.
  drm/i915: Initiate DP link training only on the lanes we'll be using
  drm/i915: Remove trailing white space
  drm/i915: Try harder during dp pattern 1 link training
  drm/i915: Make DP prepare/commit consistent with DP dpms
  drm/i915: Let panel power sequencing hardware do its job
  drm/i915: Treat PCH eDP like DP in most places
  drm/i915: Remove link_status field from intel_dp structure
  drm/i915: Move common PCH_PP_CONTROL setup to ironlake_get_pp_control
  drm/i915: Module parameters using '-1' as default must be signed type
  drm/i915: Turn on another required clock gating bit on gen6.
  drm/i915: Turn on a required 3D clock gating bit on Sandybridge.
  ...

Count of selector voltage is required for regulator_set_voltage
to work via set_voltage_sel. VDD1/2 currently have it as zero,
so regulator_set_voltage won't work for VDD1/2.
Update count (n_voltages) for VDD1/2.

Output Voltage = (step value * 12.5 mV + 562.5 mV) * gain

With above expr, number of voltages that can be selected is
step value count * gain count

constant for gain count will be called VDD1_2_NUM_VOLT_COARSE

existing constant for step value count is VDD1_2_NUM_VOLTS,
use VDD1_2_NUM_VOLT_FINE instead to make clear that step value
is not the only component in deciding selectable voltage count

Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The function i2cdev_notifier_call is used only in i2c-dev file
making it static.
Also removes the following sparse warning

drivers/i2c/i2c-dev.c:582:5: warning: symbol 'i2cdev_notifier_call'
was not declared. Should it be static?

Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Last piece of code using ANY_I2C_BUS was deleted almost 2 years ago,
so ANY_I2C_BUS can go away as well.

Signed-off-by: Jean Delvare <khali@linux-fr.org>

10-bit addresses overlap with traditional 7-bit addresses, leading in
device name collisions. Add an arbitrary offset to 10-bit addresses to
prevent this collision. The offset was chosen so that the address is
still easily recognizable.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>