- Jun 11, 2015
-
-
Kenneth Klette Jonassen authored
CAIA Delay-Gradient (CDG) is a TCP congestion control that modifies the TCP sender in order to [1]: o Use the delay gradient as a congestion signal. o Back off with an average probability that is independent of the RTT. o Coexist with flows that use loss-based congestion control, i.e., flows that are unresponsive to the delay signal. o Tolerate packet loss unrelated to congestion. (Disabled by default.) Its FreeBSD implementation was presented for the ICCRG in July 2012; slides are available at http://www.ietf.org/proceedings/84/iccrg.html Running the experiment scenarios in [1] suggests that our implementation achieves more goodput compared with FreeBSD 10.0 senders, although it also causes more queueing delay for a given backoff factor. The loss tolerance heuristic is disabled by default due to safety concerns for its use in the Internet [2, p. 45-46]. We use a variant of the Hybrid Slow start algorithm in tcp_cubic to reduce the probability of slow start overshoot. [1] D.A. Hayes and G. Armitage. "Revisiting TCP congestion control using delay gradients." In Networking 2011, pages 328-341. Springer, 2011. [2] K.K. Jonassen. "Implementing CAIA Delay-Gradient in Linux." MSc thesis. Department of Informatics, University of Oslo, 2015. Cc: Eric Dumazet <edumazet@google.com> Cc: Yuchung Cheng <ycheng@google.com> Cc: Stephen Hemminger <stephen@networkplumber.org> Cc: Neal Cardwell <ncardwell@google.com> Cc: David Hayes <davihay@ifi.uio.no> Cc: Andreas Petlund <apetlund@simula.no> Cc: Dave Taht <dave.taht@bufferbloat.net> Cc: Nicolas Kuhn <nicolas.kuhn@telecom-bretagne.eu> Signed-off-by:
Kenneth Klette Jonassen <kennetkl@ifi.uio.no> Acked-by:
Yuchung Cheng <ycheng@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Kenneth Klette Jonassen authored
Upcoming tcp_cdg uses tcp_enter_cwr() to initiate PRR. Export this function so that CDG can be compiled as a module. Cc: Eric Dumazet <edumazet@google.com> Cc: Yuchung Cheng <ycheng@google.com> Cc: Stephen Hemminger <stephen@networkplumber.org> Cc: Neal Cardwell <ncardwell@google.com> Cc: David Hayes <davihay@ifi.uio.no> Cc: Andreas Petlund <apetlund@simula.no> Cc: Dave Taht <dave.taht@bufferbloat.net> Cc: Nicolas Kuhn <nicolas.kuhn@telecom-bretagne.eu> Signed-off-by:
Kenneth Klette Jonassen <kennetkl@ifi.uio.no> Acked-by:
Yuchung Cheng <ycheng@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Scott Feldman authored
If CONFIG_NET_SWITCHDEV is enabled, but port driver does not implement support for IPv4 FIB add/del ops, don't fail route add/del offload operations. Route adds will not be marked as OFFLOAD. Routes will be installed in the kernel FIB, as usual. This was report/fixed by Florian when testing DSA driver with net-next on devices with L2 offload support but no L3 offload support. What he reported was an initial route installed from DHCP client would fail (route not installed to kernel FIB). This was triggering the setting of ipv4.fib_offload_disabled, which would disable route offloading after the first failure. So subsequent attempts to install the route would succeed. There is follow-on work/discussion to address the handling of route install failures, but for now, let's differentiate between no support and failed support. Reported-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
Scott Feldman <sfeldma@gmail.com> Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Florian Fainelli says: ==================== net: phy: broadcom: define pseudo-PHY address This patch series converts existing in-tree users of the Broadcom pseudo-PHY address (30) used to configure MDIO-connected switches to share a constant in a shared header files. ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Florian Fainelli authored
Utilize the newly introduced BRCM_PSEUDO_PHY_ADDR constant from brcmphy.h instead of open-coding the Broadcom Ethernet switches pseudo-PHY address (30). Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Florian Fainelli authored
What BGMAC defines as BGMAC_PHY_NOREGS is in fact the Broadcom Ethernet switches' pseudo-PHY address (30), utilize the newly introduced constant from brcmphy.h Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Florian Fainelli authored
What B44 has been locally using as B44_PHY_ADDR_NO_LOCAL_PHY is in fact the Broadcom Ethernet switches pseudo-PHY address (30). Update the header to use the newly introduced constant and update comments so they are within 80 columns and consistent. Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Florian Fainelli authored
Define the pseudo-PHY address (30) which is used by all Broadcom Ethernet switches in a shared header file. Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Florian Fainelli authored
We utilize inline functions from the PHY library, make sure that we do include phy.h in brcmphy.h in order for the code including brcmphy.h not to have to resolve this inclusion dependency. Fixes: 70531479 ("net: phy: broadcom: move shadow 0x1C register accessors to brcmphy.h") Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
dctcp_alpha can be read by from dctcp_get_info() without synchro, so use WRITE_ONCE() to prevent compiler from using dctcp_alpha as a temporary variable. Also, playing with small dctcp_shift_g (like 1), can expose an overflow with 32bit values shifted 9 times before divide. Use an u64 field to avoid this problem, and perform the divide only if acked_bytes_ecn is not zero. Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Merge tag 'mac80211-next-for-davem-2015-06-10' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next Johannes Berg says: ==================== For this round we mostly have fixes: * mesh fixes from Alexis Green and Chun-Yeow Yeoh, * a documentation fix from Jakub Kicinski, * a missing channel release (from Michal Kazior), * a fix for a signal strength reporting bug (from Sara Sharon), * handle deauth while associating (myself), * don't report mangled TX SKB back to userspace for status (myself), * handle aggregation session timeouts properly in fast-xmit (myself) However, there are also a few cleanups and one big change that affects all drivers (and that required me to pull in your tree) to change the mac80211 HW flags to use an unsigned long bitmap so that we can extend them more easily - we're running out of flags even with a cleanup to remove the two unused ones. ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Stephen Smalley authored
SCM_SECURITY was originally only implemented for datagram sockets, not for stream sockets. However, SCM_CREDENTIALS is supported on Unix stream sockets. For consistency, implement Unix stream support for SCM_SECURITY as well. Also clean up the existing code and get rid of the superfluous UNIXSID macro. Motivated by https://bugzilla.redhat.com/show_bug.cgi?id=1224211, where systemd was using SCM_CREDENTIALS and assumed wrongly that SCM_SECURITY was also supported on Unix stream sockets. Signed-off-by:
Stephen Smalley <sds@tycho.nsa.gov> Acked-by:
Paul Moore <paul@paul-moore.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Vaishali Thakkar authored
Use the timer API function setup_timer instead of structure field assignments to initialize a timer. A simplified version of the Coccinelle semantic patch that performs this transformation is as follows: @change@ expression e1, e2, a; @@ -init_timer(&e1); +setup_timer(&e1, a, 0UL); ... when != a = e2 -e1.function = a; Signed-off-by:
Vaishali Thakkar <vthakkar1994@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Raghu Vatsavayi authored
Following patch V8 adds support for Cavium Liquidio pci express based 10Gig ethernet adapters. 1) Consolidated all debug macros to either call dev_* or netdev_* macros directly, feedback from previous patch. 2) Changed soft commands to avoid crash when running in interrupt context. 3) Fixed link status not reflecting correct status when NetworkManager is running. Added MODULE_FIRMWARE declarations. Following were the previous patches. Patch V7: 1) Minor comments from v6 release regarding debug statements. 2) Fix for large multicast lists. 3) Fixed lockup issue if port initialization fails. 4) Enabled MSI by default. https://patchwork.ozlabs.org/patch/464441/ Patch V6: 1) Addressed the uint64 vs u64 issue, feedback from previous patch. 2) Consolidated some receive processing routines. 3) Removed link status polling method. https://patchwork.ozlabs.org/patch/459514/ Patch V5: Based on the feedback from earlier patches with regards to consolidation of common functions like device init, register programming for cn66xx and cn68xx devices. https://patchwork.ozlabs.org/patch/438979/ Patch V4: Following were the changes based on the feedback from earlier patch: 1) Added mmiowb while synchronizing queue updates and other hw interactions. 2) Statistics will now be incremented non-atomically per each ring. liquidio_get_stats will add stats of each ring while reporting the total statistics counts. 3) Modified liquidio_ioctl to return proper return codes. 4) Modified device naming to use standard Ethernet naming. 5) Global function names in the driver will have lio_/liquidio_/octeon_ prefix. 6) Ethtool related changes for: Removed redundant stats and jiffies. Use default ethtool handler of link status. Speed setting will make use of ethtool_cmd_speed_set. 7) Added checks for pci_map_* return codes. 8) Check for signals while waiting in interruptible mode https://patchwork.ozlabs.org/patch/435073/ Patch v3: Implemented feedback from previous patch like: Removed NAPI Config and DEBUG config options, added BQL and xmit_more support. https://patchwork.ozlabs.org/patch/422749/ Patch V2: Implemented feedback from previous patch. https://patchwork.ozlabs.org/patch/413539/ First Patch: https://patchwork.ozlabs.org/patch/412946/ Signed-off-by:
Derek Chickles <derek.chickles@caviumnetworks.com> Signed-off-by:
Satanand Burla <satananda.burla@caviumnetworks.com> Signed-off-by:
Felix Manlunas <felix.manlunas@caviumnetworks.com> Signed-off-by:
Robert Richter <Robert.Richter@caviumnetworks.com> Signed-off-by:
Aleksey Makarov <Aleksey.Makarov@caviumnetworks.com> Signed-off-by:
Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queueDavid S. Miller authored
Jeff Kirsher says: ==================== Intel Wired LAN Driver Updates 2015-06-09 This series contains updates to ixgbe only. The series adds additional support for x550 support, such as WoL and auto-negotiation of flow control. Adds new PHY support (external PHY) for x550, as well as the new methods/functions needed to support the new PHY's. Fixed a bug found in code inspection, where a check was missed when clearing counters for x550. Also fixed the init code flow for copper x550 devices. ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Hariprasad Shenai says: ==================== Add cim_ma_la, cim_pif_la and tx_rate debugfs entry This patch series adds the following. Add debugfs entry to dump CIM MA logic analyzer and CIM PIF logic analyzer logs. Also adds support to dump tx rate of the channels in the adapter This patch series has been created against net-next tree and includes patches on cxgb4 driver. We have included all the maintainers of respective drivers. Kindly review the change and let us know in case of any review comments. ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Hariprasad Shenai authored
Signed-off-by:
Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Hariprasad Shenai authored
Signed-off-by:
Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Hariprasad Shenai authored
Signed-off-by:
Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jiri Slaby authored
EXTRA_CFLAGS should be used on the command line only. Since EXTRA_CFLAGS here add only a non-existant path to compiler include paths (by -I), remove EXTRA_CFLAGS completely. Signed-off-by:
Jiri Slaby <jslaby@suse.cz> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Nikolay Aleksandrov authored
Before this patch the user-specified bridge port was ignored when deleting an fdb entry and thus one could delete an entry that belonged to any port. Example (eth0 and eth1 are br0 ports): bridge fdb add 00:11:22:33:44:55 dev eth0 master bridge fdb del 00:11:22:33:44:55 dev eth1 master (succeeds) after the patch: bridge fdb add 00:11:22:33:44:55 dev eth0 master bridge fdb del 00:11:22:33:44:55 dev eth1 master RTNETLINK answers: No such file or directory Based on a patch by Wilson Kok. Reported-by:
Wilson Kok <wkok@cumulusnetworks.com> Signed-off-by:
Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Merge tag 'linux-can-next-for-4.2-20150609' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next Marc Kleine-Budde says: ==================== pull-request: can-next 2015-05-06 this is a pull request of a two patches for net-next. The first patch is by Tomas Krcka, he fixes the (currently unused) register address for acceptance filters. Oliver Hartkopp contributes a patch for the cangw, where an optional UID is added to reference routing jobs. ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
- Jun 10, 2015
-
-
Johannes Berg authored
As we're running out of hardware capability flags pretty quickly, convert them to use the regular test_bit() style unsigned long bitmaps. This introduces a number of helper functions/macros to set and to test the bits, along with new debugfs code. The occurrences of an explicit __clear_bit() are intentional, the drivers were never supposed to change their supported bits on the fly. We should investigate changing this to be a per-frame flag. Signed-off-by:
Johannes Berg <johannes.berg@intel.com>
-
Johannes Berg authored
Merge back net-next to get wireless driver changes (from Kalle) to be able to create the API change across all trees properly. Signed-off-by:
Johannes Berg <johannes.berg@intel.com>
-
Alexis Green authored
This patch fixes a bug in hwmp_preq_frame_process where the wrong metric can be used when forwarding a PREQ. This happens because the code uses the same metric variable to record the value of the metric to the source of the PREQ and the value of the metric to the target of the PREQ. This comes into play when both reply and forward are set which happens when IEEE80211_PREQ_PROACTIVE_PREP_FLAG is set and when MP_F_DO | MP_F_RF is set. The original code had a special case to handle the first case but not the second. The patch uses distinct variables for the two metrics which makes the code flow much clearer and removes the need to restore the original value of metric when forwarding. Signed-off-by:
Alexis Green <agreen@cococorp.com> CC: Jesse Jones <jjones@cococorp.com> Signed-off-by:
Johannes Berg <johannes.berg@intel.com>
-
git://git.open-mesh.org/linux-mergeDavid S. Miller authored
Antonio Quartulli says: ==================== Included changes: - use common Jenkins hash instead of private implementation - extend internal routing API - properly re-arrange header files inclusion - clarify precedence between '&' and '?' - remove unused ethhdr variable in batadv_gw_dhcp_recipient_get() - ensure per-VLAN structs are updated upon MAC change ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Don Skidmore authored
This patch corrects a bug in ixgbe_setup_ixfi_x550em where we were reading and modifying IXGBE_KRM_LINK_CTRL_1 but forgot to write the results back. Signed-off-by:
Don Skidmore <donald.c.skidmore@intel.com> Tested-by:
Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Don Skidmore authored
Even though X550 may later clear this value for certain devices set it initially to support copper. Signed-off-by:
Don Skidmore <donald.c.skidmore@intel.com> Tested-by:
Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Don Skidmore authored
We need to call the set_lan_id before accessing I2C and this wasn't being done so this patch corrects that. Likewise we do the same for QSFP just to be consistent. In the X550 case this is even more important as with out it the mux is not controlled properly. Signed-off-by:
Don Skidmore <donald.c.skidmore@intel.com> Tested-by:
Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Don Skidmore authored
This patch adds ixgbe_check_link_t_X550em for checking copper PHY link. We check that both the MAC and external PHY have link. This is to avoid a false link up between the internal and external PHY when the external PHY doesn't have link. Signed-off-by:
Don Skidmore <donald.c.skidmore@intel.com> Tested-by:
Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Don Skidmore authored
This patch adds support for another 10baseT X550 device. Signed-off-by:
Don Skidmore <donald.c.skidmore@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Don Skidmore authored
A subset of the X550 function pointers didn't have default methods. This didn't cause any issue with previous X550 devices as they were all redefined. However future devices will need these default values. Signed-off-by:
Don Skidmore <donald.c.skidmore@intel.com> Tested-by:
Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Don Skidmore authored
Reviewing the X550 copper init flow with the Si team resulted in a new simplified flow. We no longer wait for the PHY FW initialization complete bit to be set as this bit is only set once by the PHY at power on and then cleared on the first read. So only the first instance of running SW (or possibly MAC FW) needs to initialize the PHY. The PHY initialization has been simplified and now only requires that the PHY FW be un-stalled low-power mode or enabled the transceiver Signed-off-by:
Don Skidmore <donald.c.skidmore@intel.com> Tested-by:
Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Don Skidmore authored
This check was missed in when this new MAC type was added. Since these counts can be incremented for X550 we need to clear them. Signed-off-by:
Don Skidmore <donald.c.skidmore@intel.com> Tested-by:
Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Don Skidmore authored
Add checks for systems that don't have SFP's to avoid incorrectly acting on interrupts that are falsely interpreted as SFP events. We do this by updating the ixgbe_is_sfp to be aware of the new X550 devices. This also includes a modified check generating the EICR mask to be more forward-looking. Signed-off-by:
Don Skidmore <donald.c.skidmore@intel.com> Tested-by:
Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Don Skidmore authored
This patch adds support for receiving interrupts from a external copper PHY for the X550 part. This includes enabling, detection as well as re-enablement. Signed-off-by:
Don Skidmore <donald.c.skidmore@intel.com> Tested-by:
Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Don Skidmore authored
The over heat message is displayed for multiple reasons but the text is cut-n-pasted for each of these cases. This patch pulls the text from the same location. I noticed this as I am about to add another case. Signed-off-by:
Don Skidmore <donald.c.skidmore@intel.com> Tested-by:
Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Don Skidmore authored
This patch adds a PHY reset function ixgbe_reset_phy_t_X550em. Which allows devices that have LASI support in enable their interrupt. Signed-off-by:
Don Skidmore <donald.c.skidmore@intel.com> Tested-by:
Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Don Skidmore authored
This patch adds x550 external PHY interrupt and forced 1G/10G support. This included enabling and handling LSC and thermal sensor interrupt. ixgbe_handle_lasi() has been added for handling the interrupts received over SDP0 from the external 10baseT PHY. ixgbe_enable_lasi_ext_t_x550em and ixgbe_get_lasi_ext_t_x550em have been added to X550em to enable mask and check interrupt flags for the external PHY. Forced 1G/10G link speed is handled via ixgbe_mac_link_t_X550em. ixgbe_seupt_mac_link_t_X550em sets up the internal PHY and external PHY to either iXFI (10G) or KX (1G) based on the user selected auto advertised link speed setting. Then sets up the external PHY auto advertised link speed. Signed-off-by:
Don Skidmore <donald.c.skidmore@intel.com> Tested-by:
Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Don Skidmore authored
The I2C mux control relies on the SDP setting in the ESDP register so it is necessary to restore the value after a MAC reset. Combine all this functionality in to a support function. Signed-off-by:
Don Skidmore <donald.c.skidmore@intel.com> Tested-by:
Krishneil Singh <krishneil.k.singh@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-