- Jun 10, 2015
-
-
Irina Tirdea authored
Goodix touchscreens export through their registers a Product ID and Firmware Version. The Product ID is an ASCII encoding of the product name (e.g.: "911"). Export to sysfs (through the input subsystem) the product id and firmware version read from the device rather than using constant values. Signed-off-by:
Octavian Purdila <octavian.purdila@intel.com> Signed-off-by:
Irina Tirdea <irina.tirdea@intel.com> Acked-by:
Bastien Nocera <hadess@hadess.net> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Irina Tirdea authored
Fix sparse warning: drivers/input/touchscreen/goodix.c:182:26: warning: Variable length array is used. Replace the variable length array with fixed length. Some Goodix devices have maximum 5 touch points, while others have 10 touch points. Using the maximum length (80 bytes) for all devices will lead to wasting 40 bytes on stack when using devices with maximum 5 touch points. However, that is preferable to using kmalloc which will use even more resources. Signed-off-by:
Irina Tirdea <irina.tirdea@intel.com> Acked-by:
Bastien Nocera <hadess@hadess.net> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Irina Tirdea authored
Fix alignment to match open parenthesis detected by running checkpatch.pl --strict. Signed-off-by:
Irina Tirdea <irina.tirdea@intel.com> Acked-by:
Bastien Nocera <hadess@hadess.net> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Steve Twiss authored
This adds OnKey driver support for DA9063. Signed-off-by:
Steve Twiss <stwiss.opensource@diasemi.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
- Jun 09, 2015
-
-
Charlie Mooney authored
Previously the elan_i2c touchpad driver would simply request the firmware "/lib/firmware/elan_i2c.bin", which does not work well if there are multiple such devices in the system. Let's append the "product ID" (by using the same function as the sysfs interface for consistency) to the filename. This results in filenames of the form "/lib/firmware/elan_i2c_72.0.bin", allowing you to support multiple elan_i2c touchpads on the same device by simply naming each device's FW with its corresponding product ID. This way when you trigger a fw update the driver will load the correct binary. Signed-off-by:
Charlie Mooney <charliemooney@chromium.org> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Duson Lin authored
In order to support multiple IC types for i2c/smbus protocol, add get ic type command and use this data when checking firmware page count and signature address. Signed-off-by:
Duson Lin <dusonlin@emc.com.tw> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
- Jun 03, 2015
-
-
Dmitry Tunin authored
Focaltech touchpads report finger width in packet[5] of absolute packet. Range for width in raw format is 0x10 - 0x70. Second half-byte is always 0. 0xff is reported, when a large contact area is detected. This can be handled in userspace. Signed-off-by:
Dmitry Tunin <hanipouspilot@gmail.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Arnd Bergmann authored
The platform_sysrq_reset_seq code was intended as a way for an embedded platform to provide its own sysrq sequence at compile time. After over two years, nobody has started using it in an upstream kernel, and the platforms that were interested in it have moved on to devicetree, which can be used to configure the sequence without requiring kernel changes. The method is also incompatible with the way that most architectures build support for multiple platforms into a single kernel. Now the code is producing warnings when built with gcc-5.1: drivers/tty/sysrq.c: In function 'sysrq_init': drivers/tty/sysrq.c:959:33: warning: array subscript is above array bounds [-Warray-bounds] key = platform_sysrq_reset_seq[i]; We could fix this, but it seems unlikely that it will ever be used, so let's just remove the code instead. We still have the option to pass the sequence either in DT, using the kernel command line, or using the /sys/module/sysrq/parameters/reset_seq file. Fixes: 154b7a48 ("Input: sysrq - allow specifying alternate reset sequence") Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
- May 27, 2015
-
-
Shailendra Verma authored
The variable no_decel is bool type so assigning "true" instead of "1". Also, synaptics_i2c_get_input() has bool return type, so let's use "false" there. Signed-off-by:
Shailendra Verma <shailendra.capricorn@gmail.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Shailendra Verma authored
The variable psmouse_smartscroll is bool type so assigning true instead of 1. Signed-off-by:
Shailendra Verma <shailendra.capricorn@gmail.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Shailendra Verma authored
Signed-off-by:
Shailendra Verma <shailendra.capricorn@gmail.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Dmitry Torokhov authored
The STMPE MFD is only used with device tree configured systems (and STMPE MFD core depends on OF), so force the configuration to come from device tree only. Tested-by:
Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by:
Marek Vasut <marex@denx.de> Acked-by:
Lee Jones <lee.jones@linaro.org> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
- May 23, 2015
-
-
Dmitry Torokhov authored
When STMPE is instantiated via device tree individual MFD cells rae formed with OF modaliases, not platform modaliases, and so we need to add OF device table to the driver if we want it to load automatically: of:Nstmpe_touchscreenT<NULL>Cst,stmpe-ts Reported-by:
Heiner Kallweit <hkallweit1@gmail.com> Tested-by:
Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Rajeev Kumar authored
rajeev-dlh.kumar@st.com email-id doesn't exist anymore as I have left the company. Signed-off-by:
Rajeev Kumar <rajeevkumar.linux@gmail.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Khem Raj authored
gcc-5 defaults to gnu11 which used c99 inline semantics in c99 'inline' is not externally visible unlike gnu89, therefore we use 'static inline' which has same semantics between gnu89 and c99 Signed-off-by:
Khem Raj <raj.khem@gmail.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
- May 22, 2015
-
-
Laurent Pinchart authored
The I2C subsystem can match devices without explicit OF support based on the part of their compatible property after the comma. However, this mechanism uses the first compatible value only. For adxl34x OF device nodes the compatible property will contain the more specific "adi,adxl345" or "adi,adxl346" value first. This prevents the device node from being matched with the adxl34x driver. Fix this by adding an OF match table with an "adi,adxl345" compatible entry. There's no need to add the "adi,adxl346" entry as the ADXL346 is backward-compatible with the ADXL345 with differences handled by runtime detection of the device model. Signed-off-by:
Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reviewed-by:
Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by:
Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Laurent Pinchart authored
DT nodes should use the more specific adi,adxl345 and adi,adxl346 compatible values instead. As the ADXL346 is backward-compatible with the ADXL345, ADXL346 nodes must list both adi,adxl346 and adi,adxl345, in that order. Signed-off-by:
Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Acked-by:
Wolfram Sang <wsa@the-dreams.de> Signed-off-by:
Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Dmitry Torokhov authored
As the name suggests, always_unused argument in cyapa_gen3_set_power_mode() is never used, so there is no reason for setting it to 0. Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
- May 21, 2015
-
-
Dmitry Torokhov authored
This makes the intent a tad more clear. Reviewed-by:
Javier Martinez Canillas <javier.martinez@collabora.co.uk> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Hans de Goede authored
Now that the generic process_bitmap function has been improved to offer accurate coordinates for the first touch we can use it for v5 (dolphin) touchpads too. Besides being a nice code cleanup this also fixes the saw tooth pattern in the coordinates for the second touch the dolphin specific version had. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Hans de Goede authored
Rename alps_set_abs_params_mt to alps_set_abs_params_semi_mt, to make it clear that it is only (to be) used for semi-mt devices. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Hans de Goede authored
With the recent process_bitmap() changes all semi-mt devices always report the first finger down in slot 0, so stop using input-mt finger tracking for these. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Hans de Goede authored
All alps semi-mt touchpads give us the following data when 2 (or more) fingers are touching: 1 more or less accurate touch for the first finger down, and a bitmap with columns and rows in which 1 or more fingers are seen resulting in a crude (low res) bounding box. So far for v3, rushmore and v4 touchpads we've been reporting the coordinates of 2 opposite corners of the box when 2 fingers are touching. Ignoring the much better resolution data given in the normal position packet. This commit actually uses this data for the first touch, figures out which corner of the bounding box is closest to the first touch, and reports the coordinates of the opposite corner for the second touch, resulting in much better data for the first touch and for the single touch pointer-emulation events. This approach is similar to the one in alps_process_bitmap_dolphin, that function takes the single accurate touch info, calculates the distance to the center of the bounding box, and then puts the 2nd touch mirrored to the center. The downside of that approach is that if both touches move slowly in the same direction, the bounding box will stay the same for a while (as it is low res) and the second touch will thus been seen moving in the opposite direction until the bounding box actually changes, and then the second touch snaps to its new position resulting in a saw tooth pattern in the coordinates for the second touch, hence this new approach. This commit fixes 2 finger scrolling being choppy / jumpy on these touchpads. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Hans de Goede authored
We should decode the position packet before the packet with the bitmap data. This way we can use the more accurate position info in process_bitmap() to get better results. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Hans de Goede authored
Pinnacle / Rushmore packets contain either position info, or bitmap info, never both. So far we've in essence been storing garbage in the position / bitmap fields of the fields struct when decoding a bitmap / pos packet. We've been relying on the following sequence to get away with this: 1) Decode bitmap packet 2) Process bitmap packet 3) Decode position packet 4) Use position / button info This patch allows us to change this sequence, which will allow using the position info when processing the bitmap for more accurate results. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Hans de Goede authored
Change alps_decode_rushmore to do all decoding itself, rather then relying on alps_decode_pinnacle and then overriding some fields + or-ing in some bits. This is a preparation patch for modifying the decode functions to properly differentiate between position and bitmap packets. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Shailendra Verma authored
Signed-off-by:
Shailendra Verma <shailendra.capricorn@gmail.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Shailendra Verma authored
Signed-off-by:
Shailendra Verma <shailendra.capricorn@gmail.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
- May 16, 2015
-
-
Fabio Estevam authored
Since commit 1c6c6952 ("genirq: Reject bogus threaded irq requests") threaded IRQs without a primary handler need to be requested with IRQF_ONESHOT, otherwise the request will fail. So pass the IRQF_ONESHOT flag in this case. The semantic patch that makes this change is available in scripts/coccinelle/misc/irqf_oneshot.cocci. Signed-off-by:
Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Fabio Estevam authored
Since commit 1c6c6952 ("genirq: Reject bogus threaded irq requests") threaded IRQs without a primary handler need to be requested with IRQF_ONESHOT, otherwise the request will fail. So pass the IRQF_ONESHOT flag in this case. The semantic patch that makes this change is available in scripts/coccinelle/misc/irqf_oneshot.cocci. Signed-off-by:
Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Fabio Estevam authored
Since commit 1c6c6952 ("genirq: Reject bogus threaded irq requests") threaded IRQs without a primary handler need to be requested with IRQF_ONESHOT, otherwise the request will fail. So pass the IRQF_ONESHOT flag in this case. The semantic patch that makes this change is available in scripts/coccinelle/misc/irqf_oneshot.cocci. Signed-off-by:
Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Fabio Estevam authored
Since commit 1c6c6952 ("genirq: Reject bogus threaded irq requests") threaded IRQs without a primary handler need to be requested with IRQF_ONESHOT, otherwise the request will fail. So pass the IRQF_ONESHOT flag in this case. The semantic patch that makes this change is available in scripts/coccinelle/misc/irqf_oneshot.cocci. Signed-off-by:
Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Evgeniy Dushistov authored
max7359_build_keycode() does the same thing as matrix_keypad_build_keymap(), but the latter can also handle DT bindings. Tested on beagleboard-xm. Signed-off-by:
Evgeniy A. Dushistov <dushistov@mail.ru> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Evgeniy Dushistov authored
In datasheet of max7359 there is the following description of this flag: 0 - INT cleared when FIFO empty, 1 - INT cleared after host read. In this mode, I2C should read FIFO until interrupt condition removed, or further INT may be lost. So, if we set this flag, we have to read FIFO until it becomes empty. But in interrupt we read FIFO just once. This lead to "keyboard" hang until reboot, if we press several keys, because of interrupt handler read just one "press" from FIFO and clear interrupt. Signed-off-by:
Evgeniy A. Dushistov <dushistov@mail.ru> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Pekka Enberg authored
Use kvfree() instead of open-coding it. Signed-off-by:
Pekka Enberg <penberg@kernel.org> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
- May 14, 2015
-
-
Wei Yongjun authored
Remove duplicated include for acpi.h. Signed-off-by:
Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Wei Yongjun authored
Remove duplicated include for delay.h. Signed-off-by:
Wei Yongjun <yongjun_wei@trendmicro.com.cn> Reviewed-by:
Heiko Stuebner <heiko.stuebner@bq.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
- May 09, 2015
-
-
Dan Murphy authored
Add the TI drv2665 piezo haptic driver. This haptics IC requires the data to be streamed to the FIFO for continuous output. Datasheet can be found at: http://www.ti.com/product/drv2665 Signed-off-by:
Dan Murphy <dmurphy@ti.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Dan Murphy authored
Fix spelling of magnitude s/manginude/magnitude Signed-off-by:
Dan Murphy <dmurphy@ti.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Dan Murphy authored
Fix the Kconfig for the drv2667 as there was a copy/paste error. Signed-off-by:
Dan Murphy <dmurphy@ti.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com>
-