The results were previously ignored, anyway.

Signed-off-by: Steve Wahl <Steve.Wahl@dell.com>
Fixes: e26a5843


Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

'request_irq()' and 'free_irq()' should have the same 'dev_id'.

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

The offsets for the SZ registers are wrong. Updated.

Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reported-by: Sandeep Mann <sandeep@purestorage.com>
Tested-by: Zachary Ross <zacharyx.ross@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

Correct ntb_peer_spad_read for case when callback is not supplied

Signed-off-by: Steve Wahl <Steve.Wahl@dell.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

I would like to take maintainership for AMD NTB

Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Acked-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

When the underlying NTB H/W driver advertises more memory windows
than the number of scratchpads available to setup MW's, it is likely
that we may end up filling the remaining memory windows with garbage.
So to avoid that, lets limit the memory windows that transport driver
can setup based on the available scratchpads.

Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

Due to incorrect limit and translation register values, NTB link was
going down when the memory window was setup. Made appropriate changes
as per spec.

Fix limit register values for BAR1, which was overlapping
with the BAR23 address.

Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

AMD NTB support hotplug under B2B mode. NTB will trigger link
up/down interrupt event when doing plug add/remove, this patch
implements the two interrupt event to support B2B hotplug function.

Signed-off-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

The Skylake Xeon NTB hardware has made some changes to the register name,
offset, and the way doorbells work. Adding driver support for the new
hardware.

Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

Pull MIPS fixes from Ralf Baechle:
 "Two more MIPS fixes for 4.9:

   - RTC: Return -ENODEV so an external RTC will be tried

   - Fix mask of GPE frequency

  These two have been tested on Imagination's automated test system and
  also both received positive reviews on the linux-mips mailing list"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: Lantiq: Fix mask of GPE frequency
  MIPS: Return -ENODEV from weak implementation of rtc_mips_set_time

The hardware documentation says bit 11:10 are used for the GPE
frequency selection. Fix the mask in the define to match these bits.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Thomas Langer <thomas.langer@intel.com>
Cc: linux-mips@linux-mips.org
Cc: john@phrozen.org
Patchwork: https://patchwork.linux-mips.org/patch/14648/


Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The sync_cmos_clock function in kernel/time/ntp.c first tries to update
the internal clock of the cpu by calling the "update_persistent_clock64"
architecture specific function.  If this returns -ENODEV, it then tries
to update an external RTC using "rtc_set_ntp_time".

On the mips architecture, the weak implementation of the underlying
function would return 0 if it wasn't overridden.  This meant that the
sync_cmos_clock function would never try to update an external RTC
(if both CONFIG_GENERIC_CMOS_UPDATE and CONFIG_RTC_SYSTOHC are
configured)

Returning -ENODEV instead, means that an external RTC will be tried.

Signed-off-by: Luuk Paulussen <luuk.paulussen@alliedtelesis.co.nz>
Reviewed-by: Richard Laing <richard.laing@alliedtelesis.co.nz>
Reviewed-by: Scott Parlane <scott.parlane@alliedtelesis.co.nz>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14649/


Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Pull crypto fixes from Herbert Xu:
 "This fixes the following issues:

   - Fix pointer size when caam is used with AArch64 boot loader on
     AArch32 kernel.

   - Fix ahash state corruption in marvell driver.

   - Fix buggy algif_aed tag handling.

   - Prevent mcryptd from being used with incompatible algorithms which
     can cause crashes"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: algif_aead - fix uninitialized variable warning
  crypto: mcryptd - Check mcryptd algorithm compatibility
  crypto: algif_aead - fix AEAD tag memory handling
  crypto: caam - fix pointer size for AArch64 boot loader, AArch32 kernel
  crypto: marvell - Don't corrupt state of an STD req for re-stepped ahash
  crypto: marvell - Don't copy hash operation twice into the SRAM

Pull networking fixes from David Miller:

 1) Limit the number of can filters to avoid > MAX_ORDER allocations.
    Fix from Marc Kleine-Budde.

 2) Limit GSO max size in netvsc driver to avoid problems with NVGRE
    configurations. From Stephen Hemminger.

 3) Return proper error when memory allocation fails in
    ser_gigaset_init(), from Dan Carpenter.

 4) Missing linkage undo in error paths of ipvlan_link_new(), from Gao
    Feng.

 5) Missing necessayr SET_NETDEV_DEV in lantiq and cpmac drivers, from
    Florian Fainelli.

 6) Handle probe deferral properly in smsc911x driver.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  net: mlx5: Fix Kconfig help text
  net: smsc911x: back out silently on probe deferrals
  ibmveth: set correct gso_size and gso_type
  net: ethernet: cpmac: Call SET_NETDEV_DEV()
  net: ethernet: lantiq_etop: Call SET_NETDEV_DEV()
  vhost-vsock: fix orphan connection reset
  cxgb4/cxgb4vf: Assign netdev->dev_port with port ID
  driver: ipvlan: Unlink the upper dev when ipvlan_link_new failed
  ser_gigaset: return -ENOMEM on error instead of success
  NET: usb: cdc_mbim: add quirk for supporting Telit LE922A
  can: peak: fix bad memory access and free sequence
  phy: Don't increment MDIO bus refcount unless it's a different owner
  netvsc: reduce maximum GSO size
  drivers: net: cpsw-phy-sel: Clear RGMII_IDMODE on "rgmii" links
  can: raw: raw_setsockopt: limit number of can_filter that can be set

Since the following commit, Infiniband and Ethernet have not been
mutually exclusive.

Fixes: 4aa17b28

 mlx5: Enable mutual support for IB and Ethernet
Signed-off-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

When trying to get a regulator we may get deferred and we see
this noise:

smsc911x 1b800000.ethernet-ebi2 (unnamed net_device) (uninitialized):
   couldn't get regulators -517

Then the driver continues anyway. Which means that the regulator
may not be properly retrieved and reference counted, and may be
switched off in case noone else is using it.

Fix this by returning silently on deferred probe and let the
system work it out.

Cc: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is based on an earlier one submitted
by Jon Maxwell with the following commit message:

"We recently encountered a bug where a few customers using ibmveth on the
same LPAR hit an issue where a TCP session hung when large receive was
enabled. Closer analysis revealed that the session was stuck because the
one side was advertising a zero window repeatedly.

We narrowed this down to the fact the ibmveth driver did not set gso_size
which is translated by TCP into the MSS later up the stack. The MSS is
used to calculate the TCP window size and as that was abnormally large,
it was calculating a zero window, even although the sockets receive buffer
was completely empty."

We rely on the Virtual I/O Server partition in a pseries
environment to provide the MSS through the TCP header checksum
field. The stipulation is that users should not disable checksum
offloading if rx packet aggregation is enabled through VIOS.

Some firmware offerings provide the MSS in the RX buffer.
This is signalled by a bit in the RX queue descriptor.

Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Pradeep Satyanarayana <pradeeps@linux.vnet.ibm.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Jonathan Maxwell <jmaxwell37@gmail.com>
Reviewed-by: David Dai <zdai@us.ibm.com>
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull libnvdimm fixes from Dan Williams:
 "Several fixes to the DSM (ACPI device specific method) marshaling
  implementation.

  I consider these urgent enough to send for 4.9 consideration since
  they fix the kernel's handling of ARS (Address Range Scrub) commands.
  Especially for platforms without machine-check-recovery capabilities,
  successful execution of ARS commands enables the platform to
  potentially break out of an infinite reboot problem if a media error
  is present in the boot path. There is also a one line fix for a
  device-dax read-only mapping regression.

  Commits 9a901f54 ("acpi, nfit: fix extended status translations
  for ACPI DSMs") and 325896ff ("device-dax: fix private mapping
  restriction, permit read-only") are true regression fixes for changes
  introduced this cycle.

  Commit efda1b5d ("acpi, nfit, libnvdimm: fix / harden ars_status
  output length handling") fixes the kernel's handling of zero-length
  results, this never would have worked in the past, but we only just
  recently discovered a BIOS implementation that emits this arguably
  spec non-compliant result.

  The remaining two commits are additional fall out from thinking
  through the implications of a zero / truncated length result of the
  ARS Status command.

  In order to mitigate the risk that these changes introduce yet more
  regressions they are backstopped by a new unit test in commit
  a7de92da ("tools/testing/nvdimm: unit test acpi_nfit_ctl()") that
  mocks up inputs to acpi_nfit_ctl()"

* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  device-dax: fix private mapping restriction, permit read-only
  tools/testing/nvdimm: unit test acpi_nfit_ctl()
  acpi, nfit: fix bus vs dimm confusion in xlat_status
  acpi, nfit: validate ars_status output buffer size
  acpi, nfit, libnvdimm: fix / harden ars_status output length handling
  acpi, nfit: fix extended status translations for ACPI DSMs

Pull libata fixes from Tejun Heo:
 "This is quite late but SCT Write Same support added during this cycle
  is broken subtly but seriously and it'd be best to disable it before
  v4.9 gets released.

  This contains two commits - one low impact sata_mv fix and the
  mentioned disabling of SCT Write Same"

* 'for-4.9-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
  libata-scsi: disable SCT Write Same for the moment
  ata: sata_mv: check for errors when parsing nr-ports from dt

Pull ceph fix from Ilya Dryomov:
 "A fix for an issue with ->d_revalidate() in ceph, causing frequent
  kernel crashes.

  Marked for stable - it goes back to 4.6, but started popping up only
  in 4.8"

* tag 'ceph-for-4.9-rc9' of git://github.com/ceph/ceph-client:
  ceph: don't set req->r_locked_dir in ceph_d_revalidate

Pull ARM SoC fixes from Olof Johansson:
 "Final batch of SoC fixes

  A few fixes that have trickled in over the last week, all fixing minor
  errors in devicetrees -- UART pin assignment on Allwinner H3,
  correcting number of SATA ports on a Marvell-based Linkstation
  platform and a display clock fix for Freescale/NXP i.MX7D that fixes a
  freeze when starting up X"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: dts: orion5x: fix number of sata port for linkstation ls-gl
  ARM: dts: imx7d: fix LCDIF clock assignment
  dts: sun8i-h3: correct UART3 pin definitions

Pull m68k fixes from Geert Uytterhoeven:

 - build fix for drivers calling ndelay() in a conditional block without
   curly braces

 - defconfig updates

* tag 'm68k-for-v4.9-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
  m68k: Fix ndelay() macro
  m68k/defconfig: Update defconfigs for v4.9-rc1

Pull drm fix from Dave Airlie:
 "Just a single fix for amdgpu to just suspend the gpu on 'shutdown'
  instead of shutting it down fully, as for some reason the hw was
  getting upset in some situations"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/amdgpu: just suspend the hw on pci shutdown

This reverts commit 53855d10

.

It shouldn't have come in yet - it depends on the changes in linux-next
that will come in during the next merge window.  As Matthew Wilcox says,
the test suite is broken with the current state without the revert.

Requested-by: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Florian Fainelli says:

====================
net: ethernet: Make sure we set dev->dev.parent

This patch series builds atop:

ec988ad7

 ("phy: Don't increment MDIO
bus refcount unless it's a different owner")

FMAN is the one that potentially needs patching as well (call
SET_NETDEV_DEV), but there appears to be no way that init_phy is
called right now, or there is not such an in-tree user. Madalin, can
you comment on that?
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

The TI CPMAC driver calls into PHYLIB which now checks for
net_device->dev.parent, so make sure we do set it before calling into
any MDIO/PHYLIB related function.

Fixes: ec988ad7

 ("phy: Don't increment MDIO bus refcount unless it's a different owner")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Lantiq Etop driver calls into PHYLIB which now checks for
net_device->dev.parent, so make sure we do set it before calling into
any MDIO/PHYLIB related function.

Fixes: ec988ad7

 ("phy: Don't increment MDIO bus refcount unless it's a different owner")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

local_addr.svm_cid is host cid. We should check guest cid instead,
which is remote_addr.svm_cid. Otherwise we end up resetting all
connections to all guests.

Cc: stable@vger.kernel.org [4.8+]
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Peng Tao <bergwolf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull parisc fixes from Helge Deller:
 "Three important fixes for the parisc architecture.

  Dave provided two patches: One which purges the TLB before setting a
  PTE entry and a second one which drops unnecessary TLB flushes. Both
  patches have been tested for one week on the debian buildd servers and
  prevent random segmentation faults.

  The patch from me fixes a crash at boot inside the TLB measuring code
  on SMP machines with PA8000-PA8700 CPUs (specifically A500-44 and
  J5000 servers)"

* 'parisc-4.9-5' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Fix TLB related boot crash on SMP machines
  parisc: Remove unnecessary TLB purges from flush_dcache_page_asm and flush_icache_page_asm
  parisc: Purge TLB before setting PTE

Merge tag 'linux-can-fixes-for-4.9-20161208' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can



Marc Kleine-Budde says:

====================
pull-request: can 2016-12-08

this is a pull request for one patch.

Jiho Chu found and fixed a use-after-free error in the cleanup path in
the peak pcan USB CAN driver.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Added missing dev_port assignment in cxgb4vf driver.
Also made dev_port assignment of cxgb4 in sync with cxgb4vf driver.

Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Arjun V <arjun@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

At bootup we run measurements to calculate the best threshold for when we
should be using full TLB flushes instead of just flushing a specific amount of
TLB entries.  This performance test is run over the kernel text segment.

But running this TLB performance test on the kernel text segment turned out to
crash some SMP machines when the kernel text pages were mapped as huge pages.

To avoid those crashes this patch simply skips this test on some SMP machines
and calculates an optimal threshold based on the maximum number of available
TLB entries and number of online CPUs.

On a technical side, this seems to happen:
The TLB measurement code uses flush_tlb_kernel_range() to flush specific TLB
entries with a page size of 4k (pdtlb 0(sr1,addr)). On UP systems this purge
instruction seems to work without problems even if the pages were mapped as
huge pages.  But on SMP systems the TLB purge instruction is broadcasted to
other CPUs. Those CPUs then crash the machine because the page size is not as
expected.  C8000 machines with PA8800/PA8900 CPUs were not affected by this
problem, because the required cache coherency prohibits to use huge pages at
all.  Sadly I didn't found any documentation about this behaviour, so this
finding is purely based on testing with phyiscal SMP machines (A500-44 and
J5000, both were 2-way boxes).

Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: Helge Deller <deller@gmx.de>

Pull SCSI fix from James Bottomley:
 "One small fix for a regression in a prior fix (again).

  This time the condition in the prior fix BUG_ON proved to be wrong
  under certain circumstances causing a BUG to trigger where it
  shouldn't in the lpfc driver"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: lpfc: fix oops/BUG in lpfc_sli_ringtxcmpl_put()

When netdev_upper_dev_unlink failed in ipvlan_link_new, need to
unlink the ipvlan dev with upper dev.

Signed-off-by: Gao Feng <fgao@ikuai8.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If we can't allocate the resources in gigaset_initdriver() then we
should return -ENOMEM instead of zero.

Fixes: 2869b23e

 ("[PATCH] drivers/isdn/gigaset: new M101 driver (v2)")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Bug report from Debian [0] shows there's minor changed model of
Linkstation LS-GL that uses the 2nd SATA port of the SoC.
So it's necessary to enable two SATA ports, though for that specific
model only the 2nd one is used.

[0] https://bugs.debian.org/845611

Fixes: b1742ffa

 ("ARM: dts: orion5x: add device tree for buffalo linkstation ls-gl")
Reported-by: Ryan Tandy <ryan@nardis.ca>
Tested-by: Ryan Tandy <ryan@nardis.ca>
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

Telit LE922A MBIM based composition does not work properly
with altsetting toggle done in cdc_ncm_bind_common.

This patch adds CDC_MBIM_FLAG_AVOID_ALTSETTING_TOGGLE quirk
to avoid this procedure that, instead, is mandatory for
other modems.

Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix for bad memory access while disconnecting. netdev is freed before
private data free, and dev is accessed after freeing netdev.

This makes a slub problem, and it raise kernel oops with slub debugger
config.

Signed-off-by: Jiho Chu <jiho.chu@samsung.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This function sets req->r_locked_dir which is supposed to indicate to
ceph_fill_trace that the parent's i_rwsem is locked for write.
Unfortunately, there is no guarantee that the dir will be locked when
d_revalidate is called, so we really don't want ceph_fill_trace to do
any dcache manipulation from this context. Clear req->r_locked_dir since
it's clearly not safe to do that.

What we really want to know with d_revalidate is whether the dentry
still points to the same inode. ceph_fill_trace installs a pointer to
the inode in req->r_target_inode, so we can just compare that to
d_inode(dentry) to see if it's the same one after the lookup.

Also, since we aren't generally interested in the parent here, we can
switch to using a GETATTR to hint that to the MDS, which also means that
we only need to reserve one cap.

Finally, just remove the d_unhashed check. That's really outside the
purview of a filesystem's d_revalidate. If the thing became unhashed
while we're checking it, then that's up to the VFS to handle anyway.

Fixes: 200fd27c ("ceph: use lookup request to revalidate dentry")
Link: http://tracker.ceph.com/issues/18041


Reported-by: Donatas Abraitis <donatas.abraitis@gmail.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Reviewed-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>