This patch adds xgene_enet_check_phy_hanlde() function that checks whether
MDIO driver is probed successfully and sets pdata->mdio_driver to true.
If MDIO driver is not probed, ethernet driver falls back to backward
compatibility mode.

Since enum xgene_enet_cmd is used by MDIO driver, removing this from
ethernet driver.

Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Fushen Chen <fchen@apm.com>
Tested-by: Toan Le <toanle@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, SGMII based 1G rely on the hardware registers for link state
and sometimes it's not reliable.  To get most accurate link state, this
interface has to use the MDIO bus to poll the PHY.

In X-Gene SoC, MDIO bus is shared across RGMII and SGMII based 1G
interfaces, so adding this driver to manage MDIO bus.  This driver
registers the mdio bus and registers the PHYs connected to it.

Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Fushen Chen <fchen@apm.com>
Tested-by: Toan Le <toanle@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes clock reset sequence.

- Added clock reset sequence for ACPI
- Added delay in clock reset sequence to make sure pulse is generated
- Added clk_unprepare_disable() in port shutdown to make sure
  clock increment/decrement counts are matching
- Removed MII_MGMT_CONFIG programming, since it is not required
- Fixed programming XGENET_CONFIG_REG to enable SGMII mode

Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Fushen Chen <fchen@apm.com>
Tested-by: Toan Le <toanle@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the driver is configured as kernel module and when it gets
unloaded and reloaded, kernel crash was observed.  This patch
addresses the software cleanup by doing the following,

- Moved register_netdev call after hardware is ready
- Since ndev is not ready, added set_irq_name to set irq name
- Since ndev is not ready, changed mdio_bus->parent to pdev->dev
- Replaced netif_start(stop)_queue by netif_tx_start(stop)_queues
- Removed napi_del call since it's called by free_netdev
- Added dev_close call, within remove
- Added shutdown callback
- Changed to use dmam_ APIs

Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Fushen Chen <fchen@apm.com>
Tested-by: Toan Le <toanle@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the driver is configured as kernel module and when it gets
unloaded and reloaded, kernel crash was observed.  This patch
address the hardware resource cleanups by doing the following,

- Added mac_ops->clear() to do prefetch buffer clean up
- Fixed delete freepool buffers logic
- Reordered mac_enable and mac_disable
- Added Tx completion ring free
- Moved down delete_desc_rings after ring cleanup

Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Fushen Chen <fchen@apm.com>
Tested-by: Toan Le <toanle@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since mac_init is too heavy to be called when the link changes,
moved the speed_set configuration to a new function and added
mac_ops->set_speed function pointer.  This function will be
called from adjust_link callback.

Added cases for 10/100 support for SGMII based 1G interface.

Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Fushen Chen <fchen@apm.com>
Tested-by: Toan Le <toanle@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Cong Wang says:

====================
net_sched: refactor tc action structures

These two patches factor out the struct tcf_common.

v2: fix a compile warning
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

After the previous patch, struct tc_action should be enough
to represent the generic tc action, tcf_common is not necessary
any more. This patch gets rid of it to make tc action code
more readable.

Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

struct tc_action is confusing, currently we use it for two purposes:
1) Pass in arguments and carry out results from helper functions
2) A generic representation for tc actions

The first one is error-prone, since we need to make sure we don't
miss anything. This patch aims to get rid of this use, by moving
tc_action into tcf_common, so that they are allocated together
in hashtable and can be cast'ed easily.

And together with the following patch, we could really make
tc_action a generic representation for all tc actions and each
type of action can inherit from it.

Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The earlier patch c3aaa06d

 (ipvlan: scrub skb before routing
in L3 mode.) did this but only for TX path in L3 mode. This
patch extends it for both the modes for TX/RX path.

Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael Chan says:

====================
bnxt_en: Improve ntuple filters and add new IDs.

Improve ntuple filters and add some new PCI device IDs.  Please review
for net-next.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Add 5741X/5731X NPAR device IDs and dual media SFP/10GBase-T device IDs.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If there are not enough resources to enable ntuple filtering,
log a warning message.

v2: Use single message and add missing newline.

Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Include the destination MAC address in the ntuple filter structure.  The
current code assumes that the destination MAC address is always the MAC
address of the NIC.  This may not be true if there are macvlans, for
example.  Add destination MAC address checking and configure the filter
correctly using the correct index for the destination MAC address.

Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Slowpath completion handling is incorrectly changing
SPQ_RING_SIZE bits instead of a single one.

Fixes: 76a9a364

 ("qed: fix handling of concurrent ramrods")
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After a6127697 ("udp: prevent bugcheck if filter truncates packet
too much"), there followed various other fixes for similar cases such
as f4979fce

 ("rose: limit sk_filter trim to payload").

Latter introduced a new helper sk_filter_trim_cap(), where we can pass
the trim limit directly to the socket filter handling. Make use of it
here as well with sizeof(struct udphdr) as lower cap limit and drop the
extra skb->len test in UDP's input path.

Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

alloc_workqueue replaces deprecated create_singlethread_workqueue().

A dedicated workqueue has been used since the workitems are being used
on a packet tx/rx path. Hence, WQ_MEM_RECLAIM has been set to guarantee
forward progress under memory pressure.

An ordered workqueue has been used since workitems &cfhsi->wake_up_work
and &cfhsi->wake_down_work cannot be run concurrently.

Calls to flush_workqueue() before destroy_workqueue() have been dropped
since destroy_workqueue() itself calls drain_workqueue() which flushes
repeatedly till the workqueue becomes empty.

Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sargun Dhillon says:

====================
bpf: add bpf_probe_write_user helper & example

This patch series contains two patches that add support for a probe_write
helper to BPF programs. This allows them to manipulate user memory during
the course of tracing. The second patch in the series has an example that
uses it, in one the intended ways to divert execution.

Thanks to Alexei Starovoitov, and Daniel Borkmann for being patient, review, and
helping me get familiar with the code base. I've made changes based on their
recommendations.

This helper should be considered for experimental usage and debugging, so we
print a warning to dmesg when it is along with the command and pid when someone
tries to install a proglet that uses it. A follow-up patchset will contain a
mechanism to verify the safety of the probe beyond what was done by hand.
----
v1->v2: restrict writing to user space, as opposed to globally v2->v3: Fixed
        formatting issues v3->v4: Rename copy_to_user -> bpf_probe_write
        Simplify checking of whether or not it's safe to write
        Add warnings to dmesg
v4->v5: Raise warning level
        Cleanup location of warning code
        Make test fail when helper is broken
v5->v6: General formatting cleanup
        Rename bpf_probe_write -> bpf_probe_write_user
v6->v7: More formatting cleanup.
        Clarifying a few comments
	Clarified log message
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

This example shows using a kprobe to act as a dnat mechanism to divert
traffic for arbitrary endpoints. It rewrite the arguments to a syscall
while they're still in userspace, and before the syscall has a chance
to copy the argument into kernel space.

Although this is an example, it also acts as a test because the mapped
address is 255.255.255.255:555 -> real address, and that's not a legal
address to connect to. If the helper is broken, the example will fail
on the intermediate steps, as well as the final step to verify the
rewrite of userspace memory succeeded.

Signed-off-by: Sargun Dhillon <sargun@sargun.me>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This allows user memory to be written to during the course of a kprobe.
It shouldn't be used to implement any kind of security mechanism
because of TOC-TOU attacks, but rather to debug, divert, and
manipulate execution of semi-cooperative processes.

Although it uses probe_kernel_write, we limit the address space
the probe can write into by checking the space with access_ok.
We do this as opposed to calling copy_to_user directly, in order
to avoid sleeping. In addition we ensure the threads's current fs
/ segment is USER_DS and the thread isn't exiting nor a kernel thread.

Given this feature is meant for experiments, and it has a risk of
crashing the system, and running programs, we print a warning on
when a proglet that attempts to use this helper is installed,
along with the pid and process name.

Signed-off-by: Sargun Dhillon <sargun@sargun.me>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Verify that the device state is registered before un-registering it.
This check is required to prevent an OOPS on flows that do
re-registration of the device and its previous state was
unregistered.

Fixes: 225c7b1f

 ("IB/mlx4: Add a driver Mellanox ConnectX InfiniBand adapters")
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When CONFIG_NET_CLS_ACT isn't set 'struct tcf_exts' has no member named
'actions' and we therefore must not access it. Otherwise compilation
fails.

Fix this by introducing a new macro similar to tc_no_actions(), which
always returns 'false' if CONFIG_NET_CLS_ACT isn't set.

Fixes: 763b4b70

 ("mlxsw: spectrum: Add support in matchall mirror TC offloading")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Such a big dump of register values is hardly useful on a production
system.

Another downside of the now removed functions is that calling
emac_dump_regs resulted in at least 87 calls to dev_info while holding a
spinlock and having irqs off which is a big source of latency.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix clang build warning:

./include/net/gtp.h:1:9: warning: '_GTP_H_' is used as a header
guard here, followed by #define of a different macro [-Wheader-guard]

fix by defining _GTP_H_ and not _GTP_H

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
Mellanox 100G mlx5 minimum inline header mode

This small series from Hadar adds the support for minimum inline header mode query
in mlx5e NIC driver.

Today on TX the driver copies to the HW descriptor only up to L2 header which is the default
required mode and sufficient for today's needs.

The header in the HW descriptor is used for HW loopback steering decision, without it packets
will go directly to the wire with no questions asked.

For TX loopback steering according to L2/L3/L4 headers, ConnectX-4 requires to copy the
corresponding headers into the send queue(SQ) WQE HW descriptor so it can decide whether to loop it back
or to forward to wire.

For legacy E-Switch mode only L2 headers copy is required.
For advanced steering (E-Switch offloads) more header layers may be required to be copied,
the required mode will be advertised by FW to each VF and PF according to the corresponding
E-Switch configuration.

Changes V2:
 - Allocate query_nic_vport_context_out on the stack
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for query the minimum inline mode from the Firmware.
It is required for correct TX steering according to L3/L4 packet
headers.

Each send queue (SQ) has inline mode that defines the minimal required
headers that needs to be copied into the SQ WQE.
The driver asks the Firmware for the wqe_inline_mode device capability
value.  In case the device capability defined as "vport context" the
driver must check the reported min inline mode from the vport context
before creating its SQs.

Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Each send queue (SQ) has inline mode that defines the minimal required
inline headers in the SQ WQE.
Before sending each packet check that the minimum required headers
on the WQE are copied.

Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

I was seeing a lot of these:

    BUG: sleeping function called from invalid context at mm/slab.h:388
    in_atomic(): 0, irqs_disabled(): 0, pid: 14971, name: trinity-c2
    Preemption disabled at:[<ffffffff819bcd46>] rhashtable_walk_start+0x46/0x150

     [<ffffffff81149abb>] preempt_count_add+0x1fb/0x280
     [<ffffffff83295722>] _raw_spin_lock+0x12/0x40
     [<ffffffff811aac87>] console_unlock+0x2f7/0x930
     [<ffffffff811ab5bb>] vprintk_emit+0x2fb/0x520
     [<ffffffff811aba6a>] vprintk_default+0x1a/0x20
     [<ffffffff812c171a>] printk+0x94/0xb0
     [<ffffffff811d6ed0>] print_stack_trace+0xe0/0x170
     [<ffffffff8115835e>] ___might_sleep+0x3be/0x460
     [<ffffffff81158490>] __might_sleep+0x90/0x1a0
     [<ffffffff8139b823>] kmem_cache_alloc+0x153/0x1e0
     [<ffffffff819bca1e>] rhashtable_walk_init+0xfe/0x2d0
     [<ffffffff82ec64de>] sctp_transport_walk_start+0x1e/0x60
     [<ffffffff82edd8ad>] sctp_transport_seq_start+0x4d/0x150
     [<ffffffff8143a82b>] seq_read+0x27b/0x1180
     [<ffffffff814f97fc>] proc_reg_read+0xbc/0x180
     [<ffffffff813d471b>] __vfs_read+0xdb/0x610
     [<ffffffff813d4d3a>] vfs_read+0xea/0x2d0
     [<ffffffff813d615b>] SyS_pread64+0x11b/0x150
     [<ffffffff8100334c>] do_syscall_64+0x19c/0x410
     [<ffffffff832960a5>] return_from_SYSCALL_64+0x0/0x6a
     [<ffffffffffffffff>] 0xffffffffffffffff

Apparently we always need to call rhashtable_walk_stop(), even when
rhashtable_walk_start() fails:

 * rhashtable_walk_start - Start a hash table walk
 * @iter:       Hash table iterator
 *
 * Start a hash table walk.  Note that we take the RCU lock in all
 * cases including when we return an error.  So you must always call
 * rhashtable_walk_stop to clean up.

otherwise we never call rcu_read_unlock() and we get the splat above.

Fixes: 53fa1036 ("sctp: fix some rhashtable functions using in sctp proc/diag")
See-also: 53fa1036 ("sctp: fix some rhashtable functions using in sctp proc/diag")
See-also: f2dba9c6

 ("rhashtable: Introduce rhashtable_walk_*")
Cc: Xin Long <lucien.xin@gmail.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: stable@vger.kernel.org
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
10GbE Intel Wired LAN Driver Updates 2016-07-22

This series contains updates to ixgbe and ixgbevf only.

Emil fixes the NACK check in ixgbevf_set_uc_addr_vf() for instances where
the index is not equal to zero.  Fixes an issue where mac->ops.setup_fc
can be NULL for backplanes which can cause the driver to crash on load.

Don fixes the second parameter of the LED functions, which is the index to
the LED we are interested in affecting.  Fixed variable to store register
reads to unsigned integer.  Adds support for the new x553 hardware into
ixgbevf.  Fixed a missing rtnl lock around ixgbevf_reinit_locked().
Fixed an issue where in ixgbevf_reset_subtask() was not verifying that
the port has been removed.  Cleans up the initial crosstalk fix, since
the SFP that indicates the presence of a SFP+ module changes between
hardware types.

Babu Moger fixes typo in freeing IRQ, since the array subscript increments
after the execution of the statement.

Wei Yongjun adds the missing destroy_workqueue() before returning from
ixgbe_init_module() in the error handling case.

Tony adds range checking for setting the MTU from the VF, where the PF can
return a NACK but this was not passed on to the VF, so propagate the
results from the PF to the VF so errors can be reported.  Consolidates
mailbox read and write functions, since the recent changes to
ixgbevf_write_msg_read_ack(), other functions are performing the same
operations done here.

Colin Ian King removes a redundant check on ret_val, since ret_val has
not changed since the previous check.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

I ran into this:

    kasan: CONFIG_KASAN_INLINE enabled
    kasan: GPF could be caused by NULL-ptr deref or user memory access
    general protection fault: 0000 [#1] PREEMPT SMP KASAN
    CPU: 2 PID: 2012 Comm: trinity-c3 Not tainted 4.7.0-rc7+ #19
    Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Ubuntu-1.8.2-1ubuntu1 04/01/2014
    task: ffff8800b745f2c0 ti: ffff880111740000 task.ti: ffff880111740000
    RIP: 0010:[<ffffffff82bbf066>]  [<ffffffff82bbf066>] irttp_connect_request+0x36/0x710
    RSP: 0018:ffff880111747bb8  EFLAGS: 00010286
    RAX: dffffc0000000000 RBX: 0000000000000000 RCX: 0000000069dd8358
    RDX: 0000000000000009 RSI: 0000000000000027 RDI: 0000000000000048
    RBP: ffff880111747c00 R08: 0000000000000000 R09: 0000000000000000
    R10: 0000000069dd8358 R11: 1ffffffff0759723 R12: 0000000000000000
    R13: ffff88011a7e4780 R14: 0000000000000027 R15: 0000000000000000
    FS:  00007fc738404700(0000) GS:ffff88011af00000(0000) knlGS:0000000000000000
    CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
    CR2: 00007fc737fdfb10 CR3: 0000000118087000 CR4: 00000000000006e0
    Stack:
     0000000000000200 ffff880111747bd8 ffffffff810ee611 ffff880119f1f220
     ffff880119f1f4f8 ffff880119f1f4f0 ffff88011a7e4780 ffff880119f1f232
     ffff880119f1f220 ffff880111747d58 ffffffff82bca542 0000000000000000
    Call Trace:
     [<ffffffff82bca542>] irda_connect+0x562/0x1190
     [<ffffffff825ae582>] SYSC_connect+0x202/0x2a0
     [<ffffffff825b4489>] SyS_connect+0x9/0x10
     [<ffffffff8100334c>] do_syscall_64+0x19c/0x410
     [<ffffffff83295ca5>] entry_SYSCALL64_slow_path+0x25/0x25
    Code: 41 89 ca 48 89 e5 41 57 41 56 41 55 41 54 41 89 d7 53 48 89 fb 48 83 c7 48 48 89 fa 41 89 f6 48 c1 ea 03 48 83 ec 20 4c 8b 65 10 <0f> b6 04 02 84 c0 74 08 84 c0 0f 8e 4c 04 00 00 80 7b 48 00 74
    RIP  [<ffffffff82bbf066>] irttp_connect_request+0x36/0x710
     RSP <ffff880111747bb8>
    ---[ end trace 4cda2588bc055b30 ]---

The problem is that irda_open_tsap() can fail and leave self->tsap = NULL,
and then irttp_connect_request() almost immediately dereferences it.

Cc: stable@vger.kernel.org
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The head skb for GSO packets won't travel through the inner depths of
SCTP stack as it doesn't contain any chunks on it. That means skb->sk
doesn't get set and then when sctp_recvmsg() calls
sctp_inet6_skb_msgname() on the head_skb it panics, as this last needs
to check flags at the socket (sp->v4mapped).

The fix is to initialize skb->sk for th head skb once we are able to do
it. That is, when the first chunk is processed.

Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that the backlog processing is called with BH enabled, we have to
disable BH before taking the socket lock via bh_lock_sock() otherwise
it may dead lock:

sctp_backlog_rcv()
                bh_lock_sock(sk);

                if (sock_owned_by_user(sk)) {
                        if (sk_add_backlog(sk, skb, sk->sk_rcvbuf))
                                sctp_chunk_free(chunk);
                        else
                                backloged = 1;
                } else
                        sctp_inq_push(inqueue, chunk);

                bh_unlock_sock(sk);

while sctp_inq_push() was disabling/enabling BH, but enabling BH
triggers pending softirq, which then may try to re-lock the socket in
sctp_rcv().

[  219.187215]  <IRQ>
[  219.187217]  [<ffffffff817ca3e0>] _raw_spin_lock+0x20/0x30
[  219.187223]  [<ffffffffa041888c>] sctp_rcv+0x48c/0xba0 [sctp]
[  219.187225]  [<ffffffff816e7db2>] ? nf_iterate+0x62/0x80
[  219.187226]  [<ffffffff816f1b14>] ip_local_deliver_finish+0x94/0x1e0
[  219.187228]  [<ffffffff816f1e1f>] ip_local_deliver+0x6f/0xf0
[  219.187229]  [<ffffffff816f1a80>] ? ip_rcv_finish+0x3b0/0x3b0
[  219.187230]  [<ffffffff816f17a8>] ip_rcv_finish+0xd8/0x3b0
[  219.187232]  [<ffffffff816f2122>] ip_rcv+0x282/0x3a0
[  219.187233]  [<ffffffff810d8bb6>] ? update_curr+0x66/0x180
[  219.187235]  [<ffffffff816abac4>] __netif_receive_skb_core+0x524/0xa90
[  219.187236]  [<ffffffff810d8e00>] ? update_cfs_shares+0x30/0xf0
[  219.187237]  [<ffffffff810d557c>] ? __enqueue_entity+0x6c/0x70
[  219.187239]  [<ffffffff810dc454>] ? enqueue_entity+0x204/0xdf0
[  219.187240]  [<ffffffff816ac048>] __netif_receive_skb+0x18/0x60
[  219.187242]  [<ffffffff816ad1ce>] process_backlog+0x9e/0x140
[  219.187243]  [<ffffffff816ac8ec>] net_rx_action+0x22c/0x370
[  219.187245]  [<ffffffff817cd352>] __do_softirq+0x112/0x2e7
[  219.187247]  [<ffffffff817cc3bc>] do_softirq_own_stack+0x1c/0x30
[  219.187247]  <EOI>
[  219.187248]  [<ffffffff810aa1c8>] do_softirq.part.14+0x38/0x40
[  219.187249]  [<ffffffff810aa24d>] __local_bh_enable_ip+0x7d/0x80
[  219.187254]  [<ffffffffa0408428>] sctp_inq_push+0x68/0x80 [sctp]
[  219.187258]  [<ffffffffa04190f1>] sctp_backlog_rcv+0x151/0x1c0 [sctp]
[  219.187260]  [<ffffffff81692b07>] __release_sock+0x87/0xf0
[  219.187261]  [<ffffffff81692ba0>] release_sock+0x30/0xa0
[  219.187265]  [<ffffffffa040e46d>] sctp_accept+0x17d/0x210 [sctp]
[  219.187266]  [<ffffffff810e7510>] ? prepare_to_wait_event+0xf0/0xf0
[  219.187268]  [<ffffffff8172d52c>] inet_accept+0x3c/0x130
[  219.187269]  [<ffffffff8168d7a3>] SYSC_accept4+0x103/0x210
[  219.187271]  [<ffffffff817ca2ba>] ? _raw_spin_unlock_bh+0x1a/0x20
[  219.187272]  [<ffffffff81692bfc>] ? release_sock+0x8c/0xa0
[  219.187276]  [<ffffffffa0413e22>] ? sctp_inet_listen+0x62/0x1b0 [sctp]
[  219.187277]  [<ffffffff8168f2d0>] SyS_accept+0x10/0x20

Fixes: 860fbbc3

 ("sctp: prepare for socket backlog behavior change")
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Added a condition to avoid bonding devices with same MAC registering
as VF.

Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The check for a -ve error is redundant, remove it and just
immediately return the return value from the call to
seq_open_net.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Default kernel behavior is to delete IPv6 addresses on link
down, which entails deletion of the multicast and the
subnet-router anycast addresses. These deletions do not
happen with sysctl setting to keep global IPv6 addresses on
link down, so every link down/up causes an increment of the
anycast and multicast refcounts. These bogus refcounts may
stop these addrs from being removed on subsequent calls to
delete them. The solution is to leave the groups for the
multicast and subnet anycast on link down for the callflow
when global IPv6 addresses are kept.

Fixes: f1705ec1

 ("net: ipv6: Make address flushing on ifdown optional")
Signed-off-by: Mike Manning <mmanning@brocade.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-next-for-davem-2016-07-22' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
pull-request: wireless-drivers-next 2016-07-22

I'm sick so I have to keep this short, but here's the last pull request
to net-next. This time there's a trivial conflict with mtd tree:

http://lkml.kernel.org/g/20160720123133.44dab209@canb.auug.org.au



We concluded with Brian (CCed) that it's best that we ask Linus to fix
this. The patches have been in linux-next for a couple of days. This
time I haven't done any merge tests so I don't know if there are any
other conflicts etc.

Please let me know if there are any problems.

wireless-drivers-next patches for 4.8

Major changes:

wl18xx

* add initial mesh support

bcma

* serial flash support on non-MIPS SoCs

ath10k

* enable support for QCA9888
* disable wake_tx_queue() mac80211 op for older devices to workaround
  throughput regression

ath9k

* implement temperature compensation support for AR9003+
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Remove including <linux/version.h> that don't need it.

Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 486bdee0 ("sctp: add support for RPS and RFS")
saves skb->hash into sk->sk_rxhash so that the inet_* can
record it to flow table.

But sctp uses sock_common_recvmsg as .recvmsg instead
of inet_recvmsg, sock_common_recvmsg doesn't invoke
sock_rps_record_flow to record the flow. It may cause
that the receiver has no chances to record the flow if
it doesn't send msg or poll the socket.

So this patch fixes it by using inet_recvmsg as .recvmsg
in sctp.

Fixes: 486bdee0

 ("sctp: add support for RPS and RFS")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Davide Caratti says:

====================
macsec: fix configurable ICV length

This series provides a fix for macsec configurable ICV length. The
maximum length of ICV element has been made compliant to IEEE 802.1AE,
and error reporting in case of cipher suite configuration failure has been
improved. Finally, a test has been added to netlink verify() callback in
order to avoid creation of macsec interfaces having user-provided ICV length
values that are not supported by the cipher suite.
====================

Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Test the cipher suite initialization in case ICV length has a value
different than its default. If this test fails, creation of a new macsec
link will also fail. This avoids situations where further security
associations can't be added due to failures of crypto_aead_setauthsize(),
caused by unsupported user-provided values of the ICV length.

Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>