On i386 nlk->ngroups might be 32 or 0. Which leads to UB, resulting in
hang during boot.
Check for 0 ngroups and use (unsigned long long) as a type to shift.

Fixes: 7acf9d42 ("netlink: Do not subscribe to non-existent groups").
Reported-by: kernel test robot <rong.a.chen@intel.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'linux-can-fixes-for-4.18-20180730' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can



Marc Kleine-Budde says:

====================
pull-request: can 2018-07-30

this is a pull request of one patch for net/master.

The patch by Anton Vasilyev and the Linux Driver Verification project
fixes a memory leak in the ems_usb driver's disconnect function.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit d4ead6b3 ("net/ipv6: move metrics from dst to
rt6_info"), ipv6 metrics are shared and refcounted. rt6_set_from()
assigns the rt->from pointer and increases the refcount on from's
metrics. This reference is never released.

Introduce the fib6_metrics_release() helper and use it to release the
metrics.

Fixes: d4ead6b3 ("net/ipv6: move metrics from dst to rt6_info")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

When loading module manually, after call xenbus_switch_state to initializes
the state of the netfront device, the driver state did not change so fast
that may lead no dev created in latest kernel. This patch adds wait to make
sure xenbus knows the driver is not in closed/unknown state.

Current state:
[vm]# ethtool eth0
Settings for eth0:
	Link detected: yes
[vm]# modprobe -r xen_netfront
[vm]# modprobe  xen_netfront
[vm]# ethtool eth0
Settings for eth0:
Cannot get device settings: No such device
Cannot get wake-on-lan settings: No such device
Cannot get message level: No such device
Cannot get link status: No such device
No data available

With the patch installed.
[vm]# ethtool eth0
Settings for eth0:
	Link detected: yes
[vm]# modprobe -r xen_netfront
[vm]# modprobe xen_netfront
[vm]# ethtool eth0
Settings for eth0:
	Link detected: yes

Signed-off-by: Xiao Liang <xiliang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ems_usb_probe() allocates memory for dev->tx_msg_buffer, but there
is no its deallocation in ems_usb_disconnect().

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The meter code would create an entry for each new meter.  However, it
would not set the meter id in the new entry, so every meter would appear
to have a meter id of zero.  This commit properly sets the meter id when
adding the entry.

Fixes: 96fbc13d ("openvswitch: Add meter infrastructure")
Signed-off-by: Justin Pettit <jpettit@ovn.org>
Cc: Andy Zhou <azhou@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make ABI more strict about subscribing to group > ngroups.
Code doesn't check for that and it looks bogus.
(one can subscribe to non-existing group)
Still, it's possible to bind() to all possible groups with (-1)

Cc: "David S. Miller" <davem@davemloft.net>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As for today STMMAC_ALIGN macro (which is used to align DMA stuff)
relies on L1 line length (L1_CACHE_BYTES).
This isn't correct in case of system with several cache levels
which might have L1 cache line length smaller than L2 line. This
can lead to sharing one cache line between DMA buffer and other
data, so we can lose this data while invalidate DMA buffer before
DMA transaction.

Fix that by using SMP_CACHE_BYTES instead of L1_CACHE_BYTES for
aligning.

Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For some very small BDPs (with just a few packets) there was a
quantization effect where the target number of packets in flight
during the super-unity-gain (1.25x) phase of gain cycling was
implicitly truncated to a number of packets no larger than the normal
unity-gain (1.0x) phase of gain cycling. This meant that in multi-flow
scenarios some flows could get stuck with a lower bandwidth, because
they did not push enough packets inflight to discover that there was
more bandwidth available. This was really only an issue in multi-flow
LAN scenarios, where RTTs and BDPs are low enough for this to be an
issue.

This fix ensures that gain cycling can raise inflight for small BDPs
by ensuring that in PROBE_BW mode target inflight values with a
super-unity gain are always greater than inflight values with a gain
<= 1. Importantly, this applies whether the inflight value is
calculated for use as a cwnd value, or as a target inflight value for
the end of the super-unity phase in bbr_is_next_cycle_phase() (both
need to be bigger to ensure we can probe with more packets in flight
reliably).

This is a candidate fix for stable releases.

Fixes: 0f8782ea ("tcp_bbr: add BBR congestion control")
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Priyaranjan Jha <priyarjha@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeremy Cline says:

====================
net: socket: Fix potential spectre v1 gadgets

This fixes a pair of potential spectre v1 gadgets.

Note that because the speculation window is large, the policy is to stop
the speculative out-of-bounds load and not worry if the attack can be
completed with a dependent load or store[0].

[0] https://marc.info/?l=linux-kernel&m=152449131114778


====================

Signed-off-by: David S. Miller <davem@davemloft.net>

'family' can be a user-controlled value, so sanitize it after the bounds
check to avoid speculative out-of-bounds access.

Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jeremy Cline <jcline@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

'call' is a user-controlled value, so sanitize the array index after the
bounds check to avoid speculating past the bounds of the 'nargs' array.

Found with the help of Smatch:

net/socket.c:2508 __do_sys_socketcall() warn: potential spectre issue
'nargs' [r] (local cap)

Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jeremy Cline <jcline@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
pull-request: bpf 2018-07-28

The following pull-request contains BPF updates for your *net* tree.

The main changes are:

1) API fixes for libbpf's BTF mapping of map key/value types in order
   to make them compatible with iproute2's BPF_ANNOTATE_KV_PAIR()
   markings, from Martin.

2) Fix AF_XDP to not report POLLIN prematurely by using the non-cached
   consumer pointer of the RX queue, from Björn.

3) Fix __xdp_return() to check for NULL pointer after the rhashtable
   lookup that retrieves the allocator object, from Taehee.

4) Fix x86-32 JIT to adjust ebp register in prologue and epilogue
   by 4 bytes which got removed from overall stack usage, from Wang.

5) Fix bpf_skb_load_bytes_relative() length check to use actual
   packet length, from Daniel.

6) Fix uninitialized return code in libbpf bpf_perf_event_read_simple()
   handler, from Thomas.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

mdio_mux_iproc_probe() uses platform_set_drvdata() to store md pointer
in device, whereas mdio_mux_iproc_remove() restores md pointer by
dev_get_platdata(&pdev->dev). This leads to wrong resources release.

The patch replaces getter to platform_get_drvdata.

Fixes: 98bc865a ("net: mdio-mux: Add MDIO mux driver for iProc SoCs")
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove BUG_ON() from fib_compute_spec_dst routine and check
in_dev pointer during flowi4 data structure initialization.
fib_compute_spec_dst routine can be run concurrently with device removal
where ip_ptr net_device pointer is set to NULL. This can happen
if userspace enables pkt info on UDP rx socket and the device
is removed while traffic is flowing

Fixes: 35ebf65e ("ipv4: Create and use fib_compute_spec_dst() helper")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When driver gets notification for mtu change, driver does not handle it for
all RQs. It handles only RQ[0].

Fix is to use enic_change_mtu() interface to change mtu for vf.

Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As long the bh tasklet isn't scheduled once, no packet from the rx path
will be handled. Since the tx path also schedule the same tasklet
this situation only persits until the first packet transmission.
So fix this issue by scheduling the tasklet after link reset.

Link: https://github.com/raspberrypi/linux/issues/2617


Fixes: 55d7de9d ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet")
Suggested-by: Floris Bos <bos@je-eigen-domein.nl>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Function nfp_flower_repr_get_type_and_port expects an enum nfp_repr_type
return value but, if the repr type is unknown, returns a value of type
enum nfp_flower_cmsg_port_type.  This means that if FW encodes the port
ID in a way the driver does not understand instead of dropping the frame
driver may attribute it to a physical port (uplink) provided the port
number is less than physical port count.

Fix this and ensure a net_device of NULL is returned if the repr can not
be determined.

Fixes: 1025351a ("nfp: add flower app")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bpf_parse_prog() is protected by rcu_read_lock().
so that GFP_KERNEL is not allowed in the bpf_parse_prog().

[51015.579396] =============================
[51015.579418] WARNING: suspicious RCU usage
[51015.579444] 4.18.0-rc6+ #208 Not tainted
[51015.579464] -----------------------------
[51015.579488] ./include/linux/rcupdate.h:303 Illegal context switch in RCU read-side critical section!
[51015.579510] other info that might help us debug this:
[51015.579532] rcu_scheduler_active = 2, debug_locks = 1
[51015.579556] 2 locks held by ip/1861:
[51015.579577]  #0: 00000000a8c12fd1 (rtnl_mutex){+.+.}, at: rtnetlink_rcv_msg+0x2e0/0x910
[51015.579711]  #1: 00000000bf815f8e (rcu_read_lock){....}, at: lwtunnel_build_state+0x96/0x390
[51015.579842] stack backtrace:
[51015.579869] CPU: 0 PID: 1861 Comm: ip Not tainted 4.18.0-rc6+ #208
[51015.579891] Hardware name: To be filled by O.E.M. To be filled by O.E.M./Aptio CRB, BIOS 5.6.5 07/08/2015
[51015.579911] Call Trace:
[51015.579950]  dump_stack+0x74/0xbb
[51015.580000]  ___might_sleep+0x16b/0x3a0
[51015.580047]  __kmalloc_track_caller+0x220/0x380
[51015.580077]  kmemdup+0x1c/0x40
[51015.580077]  bpf_parse_prog+0x10e/0x230
[51015.580164]  ? kasan_kmalloc+0xa0/0xd0
[51015.580164]  ? bpf_destroy_state+0x30/0x30
[51015.580164]  ? bpf_build_state+0xe2/0x3e0
[51015.580164]  bpf_build_state+0x1bb/0x3e0
[51015.580164]  ? bpf_parse_prog+0x230/0x230
[51015.580164]  ? lock_is_held_type+0x123/0x1a0
[51015.580164]  lwtunnel_build_state+0x1aa/0x390
[51015.580164]  fib_create_info+0x1579/0x33d0
[51015.580164]  ? sched_clock_local+0xe2/0x150
[51015.580164]  ? fib_info_update_nh_saddr+0x1f0/0x1f0
[51015.580164]  ? sched_clock_local+0xe2/0x150
[51015.580164]  fib_table_insert+0x201/0x1990
[51015.580164]  ? lock_downgrade+0x610/0x610
[51015.580164]  ? fib_table_lookup+0x1920/0x1920
[51015.580164]  ? lwtunnel_valid_encap_type.part.6+0xcb/0x3a0
[51015.580164]  ? rtm_to_fib_config+0x637/0xbd0
[51015.580164]  inet_rtm_newroute+0xed/0x1b0
[51015.580164]  ? rtm_to_fib_config+0xbd0/0xbd0
[51015.580164]  rtnetlink_rcv_msg+0x331/0x910
[ ... ]

Fixes: 3a0af8fd ("bpf: BPF for lightweight tunnel infrastructure")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

The len > skb_headlen(skb) cannot be used as a maximum upper bound
for the packet length since it does not have any relation to the full
linear packet length when filtering is used from upper layers (e.g.
in case of reuseport BPF programs) as by then skb->data, skb->len
already got mangled through __skb_pull() and others.

Fixes: 4e1ec56c ("bpf: add skb_load_bytes_relative helper")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>

In linux-next tree compiling the perf tool with additional make flags
EXTRA_CFLAGS="-Wp,-D_FORTIFY_SOURCE=2 -O2" causes a compiler error.
It is the warning 'variable may be used uninitialized' which is treated
as error: I compile it using a FEDORA 28 installation, my gcc compiler
version: gcc (GCC) 8.0.1 20180324 (Red Hat 8.0.1-0.20). The file that
causes the error is tools/lib/bpf/libbpf.c.

  [root@p23lp27] # make V=1 EXTRA_CFLAGS="-Wp,-D_FORTIFY_SOURCE=2 -O2"
  [...]
  Makefile.config:849: No openjdk development package found, please
     install JDK package, e.g. openjdk-8-jdk, java-1.8.0-openjdk-devel
  Warning: Kernel ABI header at 'tools/include/uapi/linux/if_link.h'
          differs from latest version at 'include/uapi/linux/if_link.h'
    CC       libbpf.o
  libbpf.c: In function ‘bpf_perf_event_read_simple’:
  libbpf.c:2342:6: error: ‘ret’ may be used uninitialized in this
  			function [-Werror=maybe-uninitialized]
    int ret;
        ^
  cc1: all warnings being treated as errors
  mv: cannot stat './.libbpf.o.tmp': No such file or directory
  /home6/tmricht/linux-next/tools/build/Makefile.build:96: recipe for target 'libbpf.o' failed

Suggested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

Steffen Klassert says:

====================
pull request (net): ipsec 2018-07-27

1) Fix PMTU handling of vti6. We update the PMTU on
   the xfrm dst_entry which is not cached anymore
   after the flowchache removal. So update the
   PMTU of the original dst_entry instead.
   From Eyal Birger.

2) Fix a leak of kernel memory to userspace.
   From Eric Dumazet.

3) Fix a possible dst_entry memleak in xfrm_lookup_route.
   From Tommi Rantala.

4) Fix a skb leak in case we can't call nlmsg_multicast
   from xfrm_nlmsg_multicast. From Florian Westphal.

5) Fix a leak of a temporary buffer in the error path of
   esp6_input. From Zhen Lei.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

UBSAN triggers the following undefined behaviour warnings:
[...]
[   13.236124] UBSAN: Undefined behaviour in drivers/net/ethernet/amazon/ena/ena_eth_com.c:468:22
[   13.240043] shift exponent 64 is too large for 64-bit type 'long long unsigned int'
[...]
[   13.744769] UBSAN: Undefined behaviour in drivers/net/ethernet/amazon/ena/ena_eth_com.c:373:4
[   13.748694] shift exponent 64 is too large for 64-bit type 'long long unsigned int'
[...]

When splitting the address to high and low, GENMASK_ULL is used to generate
a bitmask with dma_addr_bits field from io_sq (in ena_com_prepare_tx and
ena_com_add_single_rx_desc).
The problem is that dma_addr_bits is not initialized with a proper value
(besides being cleared in ena_com_create_io_queue).
Assign dma_addr_bits the correct value that is stored in ena_dev when
initializing the SQ.

Fixes: 1738cd3e ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Gal Pressman <pressmangal@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current map_check_btf() in BPF_MAP_TYPE_ARRAY rejects
'> map->value_size' to ensure map_seq_show_elem() will not
access things beyond an array element.

Yonghong suggested that using '!=' is a more correct
check.  The 8 bytes round_up on value_size is stored
in array->elem_size.  Hence, using '!=' on map->value_size
is a proper check.

This patch also adds new tests to check the btf array
key type and value type.  Two of these new tests verify
the btf's value_size (the change in this patch).

It also fixes two existing tests that wrongly encoded
a btf's type size (pprint_test) and the value_type_id (in one
of the raw_tests[]).  However, that do not affect these two
BTF verification tests before or after this test changes.
These two tests mainly failed at array creation time after
this patch.

Fixes: a26ca7c9 ("bpf: btf: Add pretty print support to the basic arraymap")
Suggested-by: Yonghong Song <yhs@fb.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

rhashtable_lookup() can return NULL. so that NULL pointer
check routine should be added.

Fixes: 02b55e56 ("xdp: add MEM_TYPE_ZERO_COPY")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

Registration of a memory region(MR) through FRMR/fastreg(unlike FMR)
needs a connection/qp. With a proxy qp, this dependency on connection
will be removed, but that needs more infrastructure patches, which is a
work in progress.

As an intermediate fix, the get_mr returns EOPNOTSUPP when connection
details are not populated. The MR registration through sendmsg() will
continue to work even with fast registration, since connection in this
case is formed upfront.

This patch fixes the following crash:
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] SMP KASAN
Modules linked in:
CPU: 1 PID: 4244 Comm: syzkaller468044 Not tainted 4.16.0-rc6+ #361
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
RIP: 0010:rds_ib_get_mr+0x5c/0x230 net/rds/ib_rdma.c:544
RSP: 0018:ffff8801b059f890 EFLAGS: 00010202
RAX: dffffc0000000000 RBX: ffff8801b07e1300 RCX: ffffffff8562d96e
RDX: 000000000000000d RSI: 0000000000000001 RDI: 0000000000000068
RBP: ffff8801b059f8b8 R08: ffffed0036274244 R09: ffff8801b13a1200
R10: 0000000000000004 R11: ffffed0036274243 R12: ffff8801b13a1200
R13: 0000000000000001 R14: ffff8801ca09fa9c R15: 0000000000000000
FS:  00007f4d050af700(0000) GS:ffff8801db300000(0000)
knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f4d050aee78 CR3: 00000001b0d9b006 CR4: 00000000001606e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
 __rds_rdma_map+0x710/0x1050 net/rds/rdma.c:271
 rds_get_mr_for_dest+0x1d4/0x2c0 net/rds/rdma.c:357
 rds_setsockopt+0x6cc/0x980 net/rds/af_rds.c:347
 SYSC_setsockopt net/socket.c:1849 [inline]
 SyS_setsockopt+0x189/0x360 net/socket.c:1828
 do_syscall_64+0x281/0x940 arch/x86/entry/common.c:287
 entry_SYSCALL_64_after_hwframe+0x42/0xb7
RIP: 0033:0x4456d9
RSP: 002b:00007f4d050aedb8 EFLAGS: 00000246 ORIG_RAX: 0000000000000036
RAX: ffffffffffffffda RBX: 00000000006dac3c RCX: 00000000004456d9
RDX: 0000000000000007 RSI: 0000000000000114 RDI: 0000000000000004
RBP: 00000000006dac38 R08: 00000000000000a0 R09: 0000000000000000
R10: 0000000020000380 R11: 0000000000000246 R12: 0000000000000000
R13: 00007fffbfb36d6f R14: 00007f4d050af9c0 R15: 0000000000000005
Code: fa 48 c1 ea 03 80 3c 02 00 0f 85 cc 01 00 00 4c 8b bb 80 04 00 00
48
b8 00 00 00 00 00 fc ff df 49 8d 7f 68 48 89 fa 48 c1 ea 03 <80> 3c 02
00 0f
85 9c 01 00 00 4d 8b 7f 68 48 b8 00 00 00 00 00
RIP: rds_ib_get_mr+0x5c/0x230 net/rds/ib_rdma.c:544 RSP:
ffff8801b059f890
---[ end trace 7e1cea13b85473b0 ]---

Reported-by:  <syzbot+b51c77ef956678a65834@syzkaller.appspotmail.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Avinash Repaka <avinash.repaka@oracle.com>

Signed-off-by: David S. Miller <davem@davemloft.net>

Fix dev_change_tx_queue_len so it rolls back original value
upon a failure in dev_qdisc_change_tx_queue_len.
This is already done for notifirers' failures, share the code.

In case of failure in dev_qdisc_change_tx_queue_len, some tx queues
would still be of the new length, while they should be reverted.
Currently, the revert is not done, and is marked with a TODO label
in dev_qdisc_change_tx_queue_len, and should find some nice solution
to do it.
Yet it is still better to not apply the newly requested value.

Fixes: 48bfd55e ("net_sched: plug in qdisc ops change_tx_queue_len")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Reported-by: Ran Rozenstein <ranro@mellanox.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If we enable or disable xgbe flow-control by ethtool ,
it does't work.Because the parameter is not properly
assigned,so we need to adjust the assignment order
of the parameters.

Fixes: c1ce2f77 ("amd-xgbe: Fix flow control setting logic")
Signed-off-by: tangpengpeng <tangpengpeng@higon.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Break statements were missing for Geneve case in
ndo_udp_tunnel_{add/del}, thereby raw mac matchall
entries were not getting added.

Fixes: c746fc0e("cxgb4: add geneve offload support for T6")
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Devlink resources registered with devlink_resource_register() have
to be unregistered.

Fixes: 37923ed6 ("netdevsim: Add simple FIB resource controller via devlink")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Polling for the ingress queues relies on reading the producer/consumer
pointers of the Rx queue.

Prior this commit, a cached consumer pointer could be used, instead of
the actual consumer pointer and therefore report POLLIN prematurely.

This patch makes sure that the non-cached consumer pointer is used
instead.

Reported-by: Qi Zhang <qi.z.zhang@intel.com>
Tested-by: Qi Zhang <qi.z.zhang@intel.com>
Fixes: c497176c ("xsk: add Rx receive functions and poll support")
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

Commit 24dea047 ("bpf, x32: remove ld_abs/ld_ind")
removed the 4 /* Extra space for skb_copy_bits buffer */
from _STACK_SIZE, but it didn't fix the concerned code
in emit_prologue and emit_epilogue, and this error will
bring very strange kernel runtime errors. This patch
fixes it.

Fixes: 24dea047 ("bpf, x32: remove ld_abs/ld_ind")
Reported-by: Meelis Roos <mroos@linux.ee>
Bisected-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Wang YanQing <udknight@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

Fixes the following sparse warnings:

net/ipv4/igmp.c:1391:6: warning:
 symbol '__ip_mc_inc_group' was not declared. Should it be static?

Fixes: 6e2059b5 ("ipv4/igmp: init group mode as INCLUDE when join source group")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We observed high 99 and 99.9% latencies when doing RPCs with DCTCP. The
problem is triggered when the last packet of a request arrives CE
marked. The reply will carry the ECE mark causing TCP to shrink its cwnd
to 1 (because there are no packets in flight). When the 1st packet of
the next request arrives, the ACK was sometimes delayed even though it
is CWR marked, adding up to 40ms to the RPC latency.

This patch insures that CWR marked data packets arriving will be acked
immediately.

Packetdrill script to reproduce the problem:

0.000 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
0.000 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
0.000 setsockopt(3, SOL_TCP, TCP_CONGESTION, "dctcp", 5) = 0
0.000 bind(3, ..., ...) = 0
0.000 listen(3, 1) = 0

0.100 < [ect0] SEW 0:0(0) win 32792 <mss 1000,sackOK,nop,nop,nop,wscale 7>
0.100 > SE. 0:0(0) ack 1 <mss 1460,nop,nop,sackOK,nop,wscale 8>
0.110 < [ect0] . 1:1(0) ack 1 win 257
0.200 accept(3, ..., ...) = 4

0.200 < [ect0] . 1:1001(1000) ack 1 win 257
0.200 > [ect01] . 1:1(0) ack 1001

0.200 write(4, ..., 1) = 1
0.200 > [ect01] P. 1:2(1) ack 1001

0.200 < [ect0] . 1001:2001(1000) ack 2 win 257
0.200 write(4, ..., 1) = 1
0.200 > [ect01] P. 2:3(1) ack 2001

0.200 < [ect0] . 2001:3001(1000) ack 3 win 257
0.200 < [ect0] . 3001:4001(1000) ack 3 win 257
0.200 > [ect01] . 3:3(0) ack 4001

0.210 < [ce] P. 4001:4501(500) ack 3 win 257

+0.001 read(4, ..., 4500) = 4500
+0 write(4, ..., 1) = 1
+0 > [ect01] PE. 3:4(1) ack 4501

+0.010 < [ect0] W. 4501:5501(1000) ack 4 win 257
// Previously the ACK sequence below would be 4501, causing a long RTO
+0.040~+0.045 > [ect01] . 4:4(0) ack 5501   // delayed ack

+0.311 < [ect0] . 5501:6501(1000) ack 4 win 257  // More data
+0 > [ect01] . 4:4(0) ack 6501     // now acks everything

+0.500 < F. 9501:9501(0) ack 4 win 257

Modified based on comments by Neal Cardwell <ncardwell@google.com>

Signed-off-by: Lawrence Brakmo <brakmo@fb.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Otherwise interfaces get exposed under /sys/devices/virtual, which
doesn't give udev the context it needs for PCI-based predictable
interface names.

Signed-off-by: dann frazier <dann.frazier@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When received packets are dropped in virtio_net driver, received packets
counter is incremented but bytes counter is not.
As a result, for instance if we drop all packets by XDP, only received
is counted and bytes stays 0, which looks inconsistent.
IMHO received packets/bytes should be counted if packets are produced by
the hypervisor, like what common NICs on physical machines are doing.
So fix the bytes counter.

Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

Martin KaFai Lau says:

====================
The series allows the BPF loader to figure out the btf_key_id
and btf_value_id from a map's name by using BPF_ANNOTATE_KV_PAIR()
similarly as in iproute2 commit f823f36012fb ("bpf: implement
btf handling and map annotation").

It also removes the old 'typedef' way which requires two separate
typedefs (one for the key and one for the value).

By doing this, iproute2 and libbpf have one consistent way to
figure out the btf_key_type_id and btf_value_type_id for a map.

The first two patches are some prep/cleanup works. The last patch
introduces BPF_ANNOTATE_KV_PAIR.

v3:
- Replace some more *int*_t and u* usages with the
  equivalent __[su]* in btf.c

v2:
- Fix the incorrect '&&' check on container_type
  in bpf_map_find_btf_info().
- Expose the existing static btf_type_by_id() instead of
  creating a new one.
====================

Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

This patch introduces BPF_ANNOTATE_KV_PAIR to signal the
bpf loader about the btf key_type and value_type of a bpf map.
Please refer to the changes in test_btf_haskv.c for its usage.
Both iproute2 and libbpf loader will then have the same
convention to find out the map's btf_key_type_id and
btf_value_type_id from a map's name.

Fixes: 8a138aed ("bpf: btf: Add BTF support to libbpf")
Suggested-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

This patch replaces [u]int32_t and [u]int64_t usage with
__[su]32 and __[su]64.  The same change goes for [u]int16_t
and [u]int8_t.

Fixes: 8a138aed ("bpf: btf: Add BTF support to libbpf")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>

This patch sync the uapi btf.h to tools/

Fixes: 36fc3c8c bpf: btf: Clean up BTF_INT_BITS() in uapi btf.h
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>