The i.MX53 has an integrated secure real time clock. Add it to the dtsi.

Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

- add vendor prefix bhf for Beckhoff
- add new board binding bhf,cx9020

Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add a devicetree entry for the Random Number Generator Version B (RNGB).
The driver for RNGC supports version B as well.

Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00 is connected to the INT1 pin of
the FXLS8471Q accelerometer, so remove it from the unrelated ENET
group.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for Flexcan.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The Colibri iMX7 modules come with 512MB on-module SLC NAND flash
populated. Make use of it by enabling the GPMI controller.

Signed-off-by: Stefan Agner <stefan@agner.ch>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add i.MX 7 APBH DMA and GPMI NAND modules.

Signed-off-by: Stefan Agner <stefan@agner.ch>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Declared as a regulator since the driver doesn't have a reset-gpios
property for this.

This ensures that the PHY is woken up, not depending on the state the
second stage bootloader leaves the pin.

This is a workaround until a proper mechanism is provided to reset such
devices like the pwrseq library [1] for instance.

[1] https://lkml.org/lkml/2017/2/10/779



Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Declared as a regulator since the driver doesn't have a reset-gpios
property for this.

This ensures that the PHY is woken up, not depending on the state the
second stage bootloader leaves the pin.

This is a workaround until a proper mechanism is provided to reset such
devices like the pwrseq library [1] for instance.

[1] https://lkml.org/lkml/2017/2/10/779



Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

gpio-line-names may help to make work with GPIOs from user space easier.
Following examples are provided with libgpiod
https://github.com/brgl/libgpiod

 :
|# Toggle a GPIO by name, then wait for the user to press ENTER.
|$ gpioset --mode=wait `gpiofind "USR-LED-2"`=1
|# Pause execution until a single event of any type occurs. Don't print
|# anything. Find the line by name.
|$ gpiomon --num-events=1 --silent `gpiofind "USR-IN"`

Used names was taken from RIoTboard schematics, version 1 (2013.12.07).

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The Micrel PHY has its interrupt pin connected to a GPIO line. Wire
this up in the device tree.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The Marvell switch has its interrupt pin connected to a GPIO
line. Wire this up in the device tree. This then allows us to use
interrupts from the embedded Ethernet PHYs in the switch. Also wire
them up in device tree.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The Marvell switch has an EEPROM connected to it. List the size in DT,
in order to enable access to it via ethtool.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The RDU2 has a Marvell 88E6352 switch. Both the FEC and the i210
Ethernet interfaces are connected to the switch. Make the FEC the DSA
"CPU" port, and the i210 as a regular port on the switch.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The FEC has a Micrel PHY connected to it. This PHY is managed using
the bit-banging MDIO bus. Add this to the device tree.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Currently the LCD is turned on thanks to the bootloader initialization.

In order to make the kernel to turn on the LCD on is own, pass the
'enable-gpios' and 'power-supply' properties.

Also, the GPIO1_IO01 is not used as PWM functionality on this board. It is
connected to the PWREN pin of connector J14 and has a GPIO function, so
remove the PWM1 node and change the GPIO1_IO01 IOMUX to GPIO function.

Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

It is preferred to use the panel compatible string rather than passing the
LCD timming in the device tree.

So pass the "innolux,at043tn24" compatible string to describe the parallel
LCD on this board.

Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The 'uart-has-rtscts' property should be used when the board exposes the
native RTS and CTS UART pins.

On the imx6qdl-gw5xxx boards such pins are not used, so remove the
'uart-has-rtscts' property to make the hardware description correct.

Documentation/devicetree/bindings/serial/serial.txt states that
'uart-has-rtscts' and 'rts-gpios' properties are mutually exclusive.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Pass the 'backlight' property as described in
Documentation/devicetree/bindings/display/panel/simple-panel.txt

Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

It is preferred to use the panel compatible string rather than passing the LCD
timming in the device tree.

So pass the "innolux,at043tn24" compatible string to describe the parallel LCD
on this board.

Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Make the syscon-poweroff driver change only the shutdown bits on the
SNVS_LP control register.

This change fixes an issue with the RTC wakeup alarm, that was
previously disabled during power off.

Signed-off-by: Guy Shapiro <guy.shapiro@mobi-wize.com>
Reviewed-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

imx6qdl-icore-rqs boards use sgtl5000 codec and the machine
file (imx-sgtl5000) already sets SSI in slave mode and codec in
master mode, so there is no need for having this property.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Pass the phy-reset-gpios property so that Ethernet PHYs can go
through a proper reset.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The IPU that drives HDMI must have its pre_sel set to pll2_pfd_396m
to avoid stepping on the LVDS output's toes, as the PLL can't be clocked
to the pixel clock and to the LVDS serial clock (3.5*pixel clock) at the
same time.

As we are using ipu1_di0 and ipu2_di0, ensure both are switched to
to pll2_pfd2_396m to avoid issues. The LDB driver will switch the
required IPU to ldb_di1 when it uses it to drive LVDS.

Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

According to mx7sabresd schematics the MIPI CSI/DSI voltage rails
should be 2.8V but the voltage provided is a maximum of 3.3V and
minimum of 1.8V. Providing such a higher voltage might damage the
peripherals and violates the schematic settings.

Signed-off-by: Gautam Bhat <mindentropy@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Enables the ADV7180 analog video decoder sensor connected to the
IMX6 IPU on various Gateworks Ventana boards.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for Sound card and related codec(via i2c1) nodes
on Engicam GEAM6UL variant module boards.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Engicam SOM's with mounted on starter kits like icorem6(rqs), isiot
usually not explicitly named with -kit in dts file names and
instead Model has mentioned 'Starter kit' So apply the same rule
for geam SOM as well.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

GEAM6UL SOM does have single module, it doesn't come with
any variants. Maintaining imx6ul-geam.dtsi make no sense
so move all devices from .dtsi into dts file and drop the same.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

usdhc1 is enabled and assigned pinctrl-0 on imx6ul-geam.dtsi
but same thing done on imx6ul-geam-kit.dts, so remove this
re-enabled node from the same.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for fec1 node on Engicam Is.IoT variant boards.

Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for Sound card and related codec(via i2c1) nodes
on Engicam Is.IoT MX6UL variant module boards.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Maintaining separate dtsi file with common nodes make unclear and
confusing since -isiot.dtsi is available for adding common nodes.
If the nodes are common between the dts files then mark status
as "okay" otherwise mark it "disabled" so-that respective dts
can mark status "okay"

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Pull documentation format standardization from Jonathan Corbet:
 "This series converts a number of top-level documents to the RST format
  without incorporating them into the Sphinx tree. The hope is to bring
  some uniformity to kernel documentation and, perhaps more importantly,
  have our existing docs serve as an example of the desired formatting
  for those that will be added later.

  Mauro has gone through and fixed up a lot of top-level documentation
  files to make them conform to the RST format, but without moving or
  renaming them in any way. This will help when we incorporate the ones
  we want to keep into the Sphinx doctree, but the real purpose is to
  bring a bit of uniformity to our documentation and let the top-level
  docs serve as examples for those writing new ones"

* tag 'standardize-docs' of git://git.lwn.net/linux: (84 commits)
  docs: kprobes.txt: Fix whitespacing
  tee.txt: standardize document format
  cgroup-v2.txt: standardize document format
  dell_rbu.txt: standardize document format
  zorro.txt: standardize document format
  xz.txt: standardize document format
  xillybus.txt: standardize document format
  vfio.txt: standardize document format
  vfio-mediated-device.txt: standardize document format
  unaligned-memory-access.txt: standardize document format
  this_cpu_ops.txt: standardize document format
  svga.txt: standardize document format
  static-keys.txt: standardize document format
  smsc_ece1099.txt: standardize document format
  SM501.txt: standardize document format
  siphash.txt: standardize document format
  sgi-ioc4.txt: standardize document format
  SAK.txt: standardize document format
  rpmsg.txt: standardize document format
  robust-futexes.txt: standardize document format
  ...

Pull random updates from Ted Ts'o:
 "Add wait_for_random_bytes() and get_random_*_wait() functions so that
  callers can more safely get random bytes if they can block until the
  CRNG is initialized.

  Also print a warning if get_random_*() is called before the CRNG is
  initialized. By default, only one single-line warning will be printed
  per boot. If CONFIG_WARN_ALL_UNSEEDED_RANDOM is defined, then a
  warning will be printed for each function which tries to get random
  bytes before the CRNG is initialized. This can get spammy for certain
  architecture types, so it is not enabled by default"

* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
  random: reorder READ_ONCE() in get_random_uXX
  random: suppress spammy warnings about unseeded randomness
  random: warn when kernel uses unseeded randomness
  net/route: use get_random_int for random counter
  net/neighbor: use get_random_u32 for 32-bit hash random
  rhashtable: use get_random_u32 for hash_rnd
  ceph: ensure RNG is seeded before using
  iscsi: ensure RNG is seeded before use
  cifs: use get_random_u32 for 32-bit lock random
  random: add get_random_{bytes,u32,u64,int,long,once}_wait family
  random: add wait_for_random_bytes() API

Pull ->s_options removal from Al Viro:
 "Preparations for fsmount/fsopen stuff (coming next cycle). Everything
  gets moved to explicit ->show_options(), killing ->s_options off +
  some cosmetic bits around fs/namespace.c and friends. Basically, the
  stuff needed to work with fsmount series with minimum of conflicts
  with other work.

  It's not strictly required for this merge window, but it would reduce
  the PITA during the coming cycle, so it would be nice to have those
  bits and pieces out of the way"

* 'work.mount' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  isofs: Fix isofs_show_options()
  VFS: Kill off s_options and helpers
  orangefs: Implement show_options
  9p: Implement show_options
  isofs: Implement show_options
  afs: Implement show_options
  affs: Implement show_options
  befs: Implement show_options
  spufs: Implement show_options
  bpf: Implement show_options
  ramfs: Implement show_options
  pstore: Implement show_options
  omfs: Implement show_options
  hugetlbfs: Implement show_options
  VFS: Don't use save/replace_mount_options if not using generic_show_options
  VFS: Provide empty name qstr
  VFS: Make get_filesystem() return the affected filesystem
  VFS: Clean up whitespace in fs/namespace.c and fs/super.c
  Provide a function to create a NUL-terminated string from unterminated data

Pull more __copy_.._user elimination from Al Viro.

* 'work.__copy_to_user' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  drm_dp_aux_dev: switch to read_iter/write_iter

Pull uacess-unaligned removal from Al Viro:
 "That stuff had just one user, and an exotic one, at that - binfmt_flat
  on arm and m68k"

* 'work.uaccess-unaligned' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  kill {__,}{get,put}_user_unaligned()
  binfmt_flat: flat_{get,put}_addr_from_rp() should be able to fail

Pull network field-by-field copy-in updates from Al Viro:
 "This part of the misc compat queue was held back for review from
  networking folks and since davem has jus ACKed those..."

* 'misc.compat' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  get_compat_bpf_fprog(): don't copyin field-by-field
  get_compat_msghdr(): get rid of field-by-field copyin
  copy_msghdr_from_user(): get rid of field-by-field copyin