This adds support for exporting the mac80211 TXQ stats via nl80211 by
way of a nested TXQ stats attribute, as well as for configuring the
quantum and limits that were previously only changeable through debugfs.

This commit adds just the nl80211 API, a subsequent commit adds support to
mac80211 itself.

Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The driver will process the RSSI if available and send it to mac80211.
mac80211 will compute the weighted average of ack RSSI for stations.

Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Average ack rssi will be given to userspace via NL80211 interface
if firmware is capable. Userspace tool ‘iw’ can process this
information and give the output as one of the fields in
‘iw dev wlanX station dump’.

Example output :

localhost ~ #iw dev wlan-5000mhz station dump Station
34:f3:9a:aa:3b:29 (on wlan-5000mhz)
        inactive time:  5370 ms
        rx bytes:       85321
        rx packets:     576
        tx bytes:       14225
        tx packets:     71
        tx retries:     0
        tx failed:      2
        beacon loss:    0
        rx drop misc:   0
        signal:         -54 dBm
        signal avg:     -53 dBm
        tx bitrate:     866.7 MBit/s VHT-MCS 9 80MHz short GI VHT-NSS 2
        rx bitrate:     866.7 MBit/s VHT-MCS 9 80MHz short GI VHT-NSS 2
        avg ack signal: -56 dBm
        authorized:     yes
        authenticated:  yes
        associated:     yes
        preamble:       short
        WMM/WME:        yes
        MFP:            no
        TDLS peer:      no
        DTIM period:    2
        beacon interval:100
       short preamble: yes
       short slot time:yes
       connected time: 203 seconds

Main use case is to measure the signal strength of a connected station
to AP. Data packet transmit rates and bandwidth used by station can vary
a lot even if the station is at fixed location, especially if the rates
used are multi stream(2stream, 3stream) rates with different bandwidth(20/40/80 Mhz).
These multi stream rates are sensitive and station can use different transmit power
for each of the rate and bandwidth combinations. RSSI measured from these RX packets
on AP will be not stable and can vary a lot with in a short time.
Whereas 802.11 ack frames from station are sent relatively at a constant
rate (6/12/24 Mbps) with constant bandwidth(20 Mhz).
So average rssi of the ack packets is good and more accurate.

Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Currently the regulatory core does not call the regulatory callback
reg_notifier for self managed wiphys, but regulatory_hint_user() call is
independent of wiphy and is meant for all wiphys in the system. Even a
self managed wiphy may be interested in regulatory_hint_user() to know
the country code from a trusted regulatory domain change like a cellular
base station. Therefore, for the regulatory source
NL80211_REGDOM_SET_BY_USER and the user hint type
NL80211_USER_REG_HINT_CELL_BASE, call the regulatory notifier.

No current wlan driver uses the REGULATORY_WIPHY_SELF_MANAGED flag while
also registering the reg_notifier regulatory callback, therefore there
will be no impact on existing drivers without them being explicitly
modified to take advantage of this new possibility.

Signed-off-by: Amar Singhal <asinghal@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This will serve userspace entity to maintain its regulatory limitation.
More specifcally APs can use this data to calculate the WMM IE when
building: beacons, probe responses, assoc responses etc...

Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Sometimes the most updated CSA counter values are known only
to the device. Add an API to pass this data to mac80211.

Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The data structure is initialized to all zeroes, and
we already rely on that in other places, so remove the
pointless assignment to 0.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Rather than just setting the valid flags to 0 set the
whole struct to 0 since other places might rely on it.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

There's no need to do the same thing three times in
the different switch cases, pull that out to a single
place.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Since all the HE data won't fit into struct ieee80211_rx_status,
we'll (have to) move that into the SKB proper. This means we'll
need to skip over more things in the future, so rename this to
remove the vendor-only notion from it.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The 'country IE' messages in the log can be confusing and make people think
that the country code has been set to Ireland. Fix this by changing the
log messages to use 'country element' instead (as they are no longer called
'information element' in the spec anyway).

Reported-by: Bernhard Gabler <Bernhard_Gabler@web.de>
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Without this, higher layers in the kernel will return an error
code when trying to set the power state because the driver
doesn't indicate power state support. This in turn causes VTS
(Android Vendor Test Suite) failures because the WiFi HAL can't
enable power saving mode.

Signed-off-by: Bjoern Johansson <bjoernj@google.com>
Signed-off-by: Lingfeng Yang <lfy@google.com>
Signed-off-by: Roman Kiryanov <rkir@google.com>
[johannes: remove remaining code, it was useless even as a skeleton
 since it didn't even have the right function arguments]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

lockdep does not know that the locks used by IPv4 defrag
and IPv6 reassembly units are of different classes.

It complains because of following chains :

1) sch_direct_xmit()        (lock txq->_xmit_lock)
    dev_hard_start_xmit()
     xmit_one()
      dev_queue_xmit_nit()
       packet_rcv_fanout()
        ip_check_defrag()
         ip_defrag()
          spin_lock()     (lock frag queue spinlock)

2) ip6_input_finish()
    ipv6_frag_rcv()       (lock frag queue spinlock)
     ip6_frag_queue()
      icmpv6_param_prob() (lock txq->_xmit_lock at some point)

We could add lockdep annotations, but we also can make sure IPv6
calls icmpv6_param_prob() only after the release of the frag queue spinlock,
since this naturally makes frag queue spinlock a leaf in lock hierarchy.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the NetVSP v6 and 6.1 message structures, and includes
these versions into NetVSC/NetVSP version negotiation process.

Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch implement the 'Device Naming' feature of the Hyper-V
network device API. In Hyper-V on the host through the GUI or PowerShell
it is possible to enable the device naming feature which causes
the host to make available to the guest the name of the device.
This shows up in the RNDIS protocol as the friendly name.

The name has no particular meaning and is limited to 256 characters.
The value can only be set via PowerShell on the host, but could
be scripted for mass deployments. The default value is the
string 'Network Adapter' and since that is the same for all devices
and useless, the driver ignores it.

In Windows, the value goes into a registry key for use in SNMP
ifAlias. For Linux, this patch puts the value in the network
device alias property; where it is visible in ip tools and SNMP.

The host provided ifAlias is just a suggestion, and can be
overridden by later ip commands.

Also requires exporting dev_set_alias in netdev core.

Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
r8169: series with further smaller improvements

This series includes further smaller improvements.

Then I think the basic cleanup has been done and next step would be
preparing the switch to phylib.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

According to the chip configuration entries only RTL8169 (ver <= 06)
supports tx checksumming for jumbo packets.
By the way: constant JUMBO_1K is a little misleading because it refers
to the standard packet size and not to a jumbo packet size.

By implementing this rule we can get rid of configuring tx checksumming
support per chip type.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The region to be used is always the first of type IORESOURCE_MEM.
We can implement this rule directly w/o having to specify which
region is the first one per configuration entry.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

txd_version is used in rtl_init_one() only, so we can drop member
txd_version from struct rtl8169_private.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Certain entries in array mac_info[] are redundant, so remove them:
0x7cf, 0x2c200000 (VER 33): matched by entry 0x7c8, 0x2c000000
0x7cf, 0x28300000 (VER 26): matched by entry 0x7c8, 0x28000000
0x7cf, 0x3cb00000 (VER 24): matched by entry 0x7c8, 0x3c800000
0x7cf, 0x3c400000 (VER 22): matched by entry 0x7c8, 0x3c000000
0x7cf, 0x38500000 (VER 17): matched by entry 0x7c8, 0x38000000
0x7cf, 0x44900000 (VER 39): matched by entry 0x7c8, 0x44800000
0x7cf, 0x40b00000 (VER 30): matched by entry 0x7c8, 0x40800000
0x7cf, 0x40a00000 (VER 30): matched by entry 0x7c8, 0x40800000
0x7cf, 0x34a00000 (VER 09): matched by entry 0x7c8, 0x34800000
0x7cf, 0x24a00000 (VER 09): matched by entry 0x7c8, 0x24800000

In addition don't mask out bits 30 and 29 when printing the XID.
Most likely this is a relict from the times when the driver covered
RTL8169 chip version only.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For security reasons since commit ad67b74d

 "printk: hash addresses
printed with %p" %p doesn't display the full address any longer.
We could switch to %px, but I think the pointer address doesn't
provide a real benefit, so remove printing the hashed address.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We can get rid of member opts1_mask and in addition save a few cpu
cycles in the hot path of rtl_rx().

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Code can be a little simplified by switching the interrupt handler
argument type to struct rtl8169_private *.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The counter handling functions don't deal with the net_device, so code
can be simplified by changing the argument type to
struct rtl8169_private *.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Code can be simplified by changing the argument type of hw_start
callbacks from struct net_device * to struct rtl8169_private *.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This function is very simple and used only once, so we can inline
the two statements.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rx_buf_sz is constant, so we don't have to pass it as parameter and
in general can replace it with a constant.

When working on this I noticed that also before in
rtl_set_rx_max_size() a value of 0x4000 is set, what is not in line
with the chip spec. According to the spec only bits 0..13 are used
and we set an effective value of zero therefore.
However, the driver still seems to work and due to potential side
effects I'm reluctant to make a change.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rtl8169_rx_fill() is called only once and directly before the call
array tp->Rx_databuff[] is filled with zero's. Therefore we don't
need this check.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This function doesn't use the net_device, therefore change the
parameter to type struct rtl8169_private * to simplify the code.
In addition we don't need the calculations in the memset
statements, we can use the size of the arrays directly.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dev->dev.parent has the same value as tp_to_dev(tp)
(set by SET_NETDEV_DEV() in rtl_init_one()) and we know it can't be NULL.
This allows us to simplify the code.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

napi_schedule() is called from hard irq context, so we can switch to
napi_schedule_irqoff() and avoid some overhead.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We can use generic constant NAPI_POLL_WAIT instead of defining an own
constant for the same value.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Not a giant leap for mankind, but let's avoid the open-coded memcpy
and use standard helper skb_copy_to_linear_data instead.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit 6f0333b8

 "r8169: use 50% less ram for RX ring" member
align isn't used any longer, so remove it.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Member features of struct rtl8169_private isn't used any longer since
commit 6c6aa15f

 "r8169: improve interrupt handling", so remove it.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Murali Karicheri says:

====================
Add support for netcp driver on K2G SoC

K2G SoC is another variant of Keystone family of SoCs. This patch
series add support for NetCP driver on this SoC. The QMSS found on
K2G SoC is a cut down version of the QMSS found on other keystone
devices with less number of queues, internal link ram etc. The patch
series has 2 patch sets that goes into the drivers/soc and the
rest has to be applied to net sub system. Please review and merge
if this looks good.

K2G TRM is located at http://www.ti.com/lit/ug/spruhy8g/spruhy8g.pdf
Thanks

The boot logs on K2G ICE board (tftp boot over Ethernet and from mmc)
https://pastebin.ubuntu.com/p/yvZ6drFhkW/

The boot logs on K2G GP board (tftp boot over Ethernet and from mmc)
https://pastebin.ubuntu.com/p/QTr6K7s4Zp/

Also regressed boot on K2HK and K2L EVMs as we have modified GBE
version detection logic (K2E uses same version of NetCP as in K2L.
So regression on one of them is needed).

Boot log on K2L and K2HK EVMs are at
https://pastebin.ubuntu.com/p/N9DBdPjbvR/



This series applies to net-next master branch.

Change history:
  v4 - ready for merge to net-next
       Folded the series "Add promiscous mode support in k2g network driver"
       into this.
       Fixed a typo in 5/11 (sgmii to rgmii) based on TI internal comment
       Reworked 4/11 and title changed to reflect additional changes to
       exclude sgmii configuration code for 2U cpsw. Use IS_SS_ID_2U()
       macro for customization.
       Added Reviewed-by from Rob Herring against 1/13
  v3 - Addressed comments from Andrew Lunn and Grygorii Strashko
       against v2.
  v2 - Addressed following comments on initial version
       - split patch 3/5 to multiple patches from Andrew Lunn
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for promiscuous mode in k2g's network
driver. When upper layer instructs to transition from
non-promiscuous mode to promiscuous mode or vice versa
K2G network driver needs to configure ALE accordingly
so that in case of non-promiscuous mode, ALE will not flood
all unicast packets to host port, while in promiscuous
mode, it will pass all received unicast packets to
host port.

Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds an API to support setting rx mode in
netcp modules.  If a netcp module needs to be notified
when upper layer transitions from one rx mode to
another and react accordingly, such a module will implement
the new API set_rx_mode added in this patch.  Currently
rx modes supported are PROMISCUOUS and NON_PROMISCUOUS
modes.

Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The netcp driver shouldn't proceed until the knav qmss and dma
devices are ready. So return -EPROBE_DEFER if these devices are not
ready.

Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As the probe sequence is not guaranteed contrary to the assumption
of the commit 2d8e276a9030, same has to be reverted.

commit 2d8e276a9030 ("net: netcp: remove dead code from the driver")

Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>