Jeff Kirsher says:

====================
100GbE Intel Wired LAN Driver Updates 2019-11-04

This series contains updates to the ice driver only.

Anirudh refactors the code to reduce the kernel configuration flags and
introduces ice_base.c file.

Maciej does additional refactoring on the configuring of transmit
rings so that we are not configuring per each traffic class flow.
Added support for XDP in the ice driver.  Provides additional
re-organizing of the code in preparation for adding build_skb() support
in the driver.  Adjusted the computational padding logic for headroom
and tailroom to better support build_skb(), which also aligns with the
logic in other Intel LAN drivers.  Added build_skb support and make use
of the XDP's data_meta.

Krzysztof refactors the driver to prepare for AF_XDP support in the
driver and then adds support for AF_XDP.

v2: Updated patch 3 of the series based on community feedback with the
    following changes...
    - return -EOPNOTSUPP instead of ENOTSUPP for too large MTU which makes
      it impossible to attach XDP prog
    - don't check for case when there's no XDP prog currently on interface
      and ice_xdp() is called with NULL bpf_prog; this happens when user
      does "ip link set eth0 xdp off" and no prog is present on VSI; no need
      for that as it is handled by higher layer
    - drop the extack message for unknown xdp->command
    - use the smp_processor_id() for accessing the XDP Tx ring for XDP_TX
      action
    - don't leave the interface in downed state in case of any failure
      during the XDP Tx resources handling
    - undo rename of ice_build_ctob
    The above changes caused a ripple effect in patches 4 & 5 to update
    references to ice_build_ctob() which are now build_ctob()
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
10GbE Intel Wired LAN Driver Updates 2019-11-04

This series contains old Halloween candy updates, yet still sweet, to
fm10k, ixgbe and i40e.

Jake adds the missing initializers for a couple of the TLV attribute
macros.  Added support for capturing and reporting statistics for all of
the VFs in a given PF.  Lastly, bump the version of the fm10k driver to
reflect the recent changes.

Alex addresses locality issues in the ixgbe driver when it is loaded on
a system supporting multiple NUMA nodes.

Manjunath Patil provides changes to the ixgbe driver, similar to those
made to igb, to prevent transmit packets to request a hardware timestamp
when the NIC has not been setup via the SIOCSHWTSTAMP ioctl.

Alice adds support for x710 by adding the missing device id's in the
appropriate places to ensure all the features are enabled in i40e.

Jesse adds support for VF stats gathering in the i40e via the kernel
via ndo_get_vf_stats function.

v2: Fixed up commit id references in patch 5's description to align with
    how commit id's should be referenced.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Implement the VF stats gathering via the kernel via ndo_get_vf_stats().
The driver will show per-VF stats in the output of the command:
ip -s link show dev <PF>

Testing Hints:
ip -s link show dev eth0
will return non-zero VF stats.
...
   vf 0 MAC 00:55:aa:00:55:aa, spoof checking on, link-state enable, trust off
   RX: bytes  packets  mcast   bcast
   128000     1000     104     104
   TX: bytes  packets
   128000     1000

Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The I40E_DEV_ID_10G_BASE_T_BC device id was added previously,
but was not enabled in all the appropriate places.  Adding it
to enable it's use.

Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

HW timestamping can only be requested for a packet if the NIC is first
setup via ioctl(SIOCSHWTSTAMP). If this step was skipped, then the ixgbe
driver still allowed TX packets to request HW timestamping. In this
situation, we see 'clearing Tx Timestamp hang' noise in the log.

Fix this by checking that the NIC is configured for HW TX timestamping
before accepting a HW TX timestamping request.

Similar-to:
   commit 26bd4e2d ("igb: protect TX timestamping from API misuse")
   commit 0a6f2f05 ("igb: Fix a test with HWTSTAMP_TX_ON")

Signed-off-by: Manjunath Patil <manjunath.b.patil@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

An upcoming out-of-tree release will be occurring which will include the
recent functionality to support virtual function statistics. Update the
kernel driver version to match this.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is meant to address locality issues present in the ixgbe driver
when it is loaded on a system supporting multiple NUMA nodes and more CPUs
then the device can map in a 1:1 fashion. Instead of just arbitrarily
mapping itself to CPUs 0-62 it would make much more sense to map itself to
the local CPUs first, and then map itself to any remaining CPUs that might
be used.

The first effect of this is that queue 0 should always be allocated on the
local CPU/NUMA node. This is important as it is the default destination if
a packet doesn't match any existing flow director filter or RSS rule and as
such having it local should help to reduce QPI cross-talk in the event of
an unrecognized traffic type.

In addition this should increase the likelihood of the RSS queues being
allocated and used on CPUs local to the device while the ATR/Flow Director
queues would be able to route traffic directly to the CPU that is likely to
be processing it.

Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Support capturing and reporting statistics for all of the VFs associated
with a given PF device via the ndo_get_vf_stats callback.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Add the missing field initializers for a couple of the TLV attribute
macros. This resolves the last few -Wmissing-field-initializers warnings
for the fm10k Linux driver.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

At this point ice driver is able to work on order 1 pages that are split
onto two 3k buffers. Let's reflect that when user is setting new MTU
size and XDP is present on interface.

Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Driver is now prepared for building the skb around the existing Rx
buffer, so introduce the ice_build_skb responsible for it. Make use of
XDP's data_meta as well.

I've observed around 30% less CPU consumption with build_skb Rx path, in
comparison to legacy Rx. What stands behind such result is the avoidance
of flow_dissector (which we were diving into via eth_get_headlen) and no
memcpy calls.

Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Take into account the underlying architecture specific settings and
based on that calculate the possible padding that can be supplied.
Typically, for x86 and standard MTU size we will end up with 192 bytes
of headroom. This is the same behavior as our other drivers have and we
can dedicate it for XDP purposes.

Furthermore, introduce the Rx ring flag for indicating whether build_skb
is used on particular. Based on that invoke the routines for padding
calculation.

Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Add an ethtool "legacy-rx" priv flag for toggling the Rx path. This
control knob will be mainly used for build_skb usage as well as buffer
size/MTU manipulation.

In preparation for adding build_skb support in a way that it takes
care of how we set the values of max_frame and rx_buf_len fields of
struct ice_vsi. Specifically, in this patch mentioned fields are set to
values that will allow us to provide headroom and tailroom in-place.

This can be mostly broken down onto following:
- for legacy-rx "on" ethtool control knob, old behaviour is kept;
- for standard 1500 MTU size configure the buffer of size 1536, as
  network stack is expecting the NET_SKB_PAD to be provided and
  NET_IP_ALIGN can have a non-zero value (these can be typically equal
  to 32 and 2, respectively);
- for larger MTUs go with max_frame set to 9k and configure the 3k
  buffer in case when PAGE_SIZE of underlying arch is less than 8k; 3k
  buffer is implying the need for order 1 page, so that our page
  recycling scheme can still be applied;

With that said, substitute the hardcoded ICE_RXBUF_2048 and PAGE_SIZE
values in DMA API that we're making use of with rx_ring->rx_buf_len and
ice_rx_pg_size(rx_ring). The latter is an introduced helper for
determining the page size based on its order (which was figured out via
ice_rx_pg_order). Last but not least, take care of truesize calculation.

In the followup patch the headroom/tailroom computation logic will be
introduced.

This change aligns the buffer and frame configuration with other Intel
drivers, most importantly with iavf.

Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Add zero copy AF_XDP support.  This patch adds zero copy support for
Tx and Rx; code for zero copy is added to ice_xsk.h and ice_xsk.c.

For Tx, implement ndo_xsk_wakeup. As with other drivers, reuse
existing XDP Tx queues for this task, since XDP_REDIRECT guarantees
mutual exclusion between different NAPI contexts based on CPU ID. In
turn, a netdev can XDP_REDIRECT to another netdev with a different
NAPI context, since the operation is bound to a specific core and each
core has its own hardware ring.

For Rx, allocate frames as MEM_TYPE_ZERO_COPY on queues that AF_XDP is
enabled.

Signed-off-by: Krzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Co-developed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

In preparation of AF XDP, move functions that will be used both by skb and
zero-copy paths to a new file called ice_txrx_lib.c.  This allows us to
avoid using ifdefs to control the staticness of said functions.

Move other functions (ice_rx_csum, ice_rx_hash and ice_ptype_to_htype)
called only by the moved ones to the new file as well.

Signed-off-by: Krzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Commit 5bc60de5 ("selftests: bpf: Don't try to read files without
read permission") got reverted as the fix was not working as expected
and real fix came in via 8101e069 ("selftests: bpf: Skip write
only files in debugfs"). When bpf-next got merged into net-next, the
test_offload.py had a small conflict. Fix the resolution in ae8a76fb
iby not reintroducing 5bc60de5 again.

Fixes: ae8a76fb ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next"

)
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Building with W=1 (cf.scripts/Makefile.extrawarn) outputs:
warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]

Drop the unused 'ret' variable.

Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

IOC3 hardware needs a 16k aligned TX ring.

Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Set NETIF_F_HIGHDMA together with the NETIF_F_IP_CSUM flag instead of
letting the second assignment overwrite it.  Probably doesn't matter
in practice as none of the systems an IOC3 is usually found in has
highmem to start with.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need to fall back to a lower mask these days, the DMA mask
just communicates the hardware supported features.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

dma_alloc_coherent always zeroes memory, there is no need for
__GFP_ZERO.  Also doing a GFP_ATOMIC allocation just before a GFP_KERNEL
one is clearly bogus.

Fixes: ed870f6a ("net: sgi: ioc3-eth: use dma-direct for dma allocations")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

dma_direct_ is a low-level API that must never be used by drivers
directly.  Switch to use the proper DMA API instead.

Fixes: ed870f6a ("net: sgi: ioc3-eth: use dma-direct for dma allocations")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Faster jhash2() can be used instead of jhash(), since
IPv6 addresses have the needed alignment requirement.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Before this change of_get_phy_mode() returned an enum,
phy_interface_t. On error, -ENODEV etc, is returned. If the result of
the function is stored in a variable of type phy_interface_t, and the
compiler has decided to represent this as an unsigned int, comparision
with -ENODEV etc, is a signed vs unsigned comparision.

Fix this problem by changing the API. Make the function return an
error, or 0 on success, and pass a pointer, of type phy_interface_t,
where the phy mode should be stored.

v2:
Return with *interface set to PHY_INTERFACE_MODE_NA on error.
Add error checks to all users of of_get_phy_mode()
Fixup a few reverse christmas tree errors
Fixup a few slightly malformed reverse christmas trees

v3:
Fix 0-day reported errors.

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

When commit df1c0b84 ("[BRIDGE]: Packets leaking out of
disabled/blocked ports.") introduced the port state tests in
br_fdb_update() it was to avoid learning/refreshing from STP BPDUs, it was
also used to avoid learning/refreshing from user-space with NTF_USE. Those
two tests are done for every packet entering the bridge if it's learning,
but for the fast-path we already have them checked in br_handle_frame() and
is unnecessary to do it again. Thus push the checks to the unlikely cases
and drop them from br_fdb_update(), the new nbp_state_should_learn() helper
is used to determine if the port state allows br_fdb_update() to be called.
The two places which need to do it manually are:
 - user-space add call with NTF_USE set
 - link-local packet learning done in __br_handle_local_finish()

Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for XDP. Implement ndo_bpf and ndo_xdp_xmit.  Upon load of
an XDP program, allocate additional Tx rings for dedicated XDP use.
The following actions are supported: XDP_TX, XDP_DROP, XDP_REDIRECT,
XDP_PASS, and XDP_ABORTED.

Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

There's no reason for treating DCB as first class citizen when configuring
the Tx queues and going through TCs. Reverse the logic and base the
configuration logic on rings, which is the object of interest anyway.

Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove a few uses of kernel configuration flags from ice_lib.c by
introducing a new source file ice_base.c. Also move corresponding
function prototypes from ice_lib.h to ice_base.h and include ice_base.h
where required.

Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Saeed Mahameed says:

====================
mlx5-updates-2019-11-01

Misc updates for mlx5 netdev and core driver

1) Steering Core: Replace CRC32 internal implementation with standard
   kernel lib.
2) Steering Core: Support IPv4 and IPv6 mixed matcher.
3) Steering Core: Lockless FTE read lookups
4) TC: Bit sized fields rewrite support.
5) FPGA: Standalone FPGA support.
6) SRIOV: Reset VF parameters configurations on SRIOV disable.
7) netdev: Dump WQs wqe descriptors on CQE with error events.
8) MISC Cleanups.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/isdn/hardware/mISDN/mISDNisar.c:30:17:
 warning: faxmodulation_s defined but not used [-Wunused-const-variable=]

It is never used, so can be removed.

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The IDT ClockMatrix (TM) family includes integrated devices that provide
eight PLL channels.  Each PLL channel can be independently configured as a
frequency synthesizer, jitter attenuator, digitally controlled
oscillator (DCO), or a digital phase lock loop (DPLL).  Typically
these devices are used as timing references and clock sources for PTP
applications.  This patch adds support for the device.

Co-developed-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Vincent Cheng <vincent.cheng.xh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add device tree binding doc for the IDT ClockMatrix PTP clock.

Signed-off-by: Vincent Cheng <vincent.cheng.xh@renesas.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

traceroute6 output can be confusing, in that it shows the address
that a router would use to reach the sender, rather than the address
the packet used to reach the router.
Consider this case:

        ------------------------ N2
         |                    |
       ------              ------  N3  ----
       | R1 |              | R2 |------|H2|
       ------              ------      ----
         |                    |
        ------------------------ N1
                  |
                 ----
                 |H1|
                 ----

where H1's default route is through R1, and R1's default route is
through R2 over N2.
traceroute6 from H1 to H2 shows R2's address on N1 rather than on N2.

The script below can be used to reproduce this scenario.

traceroute6 output without this patch:

traceroute to 2000:103::4 (2000:103::4), 30 hops max, 80 byte packets
 1  2000:101::1 (2000:101::1)  0.036 ms  0.008 ms  0.006 ms
 2  2000:101::2 (2000:101::2)  0.011 ms  0.008 ms  0.007 ms
 3  2000:103::4 (2000:103::4)  0.013 ms  0.010 ms  0.009 ms

traceroute6 output with this patch:

traceroute to 2000:103::4 (2000:103::4), 30 hops max, 80 byte packets
 1  2000:101::1 (2000:101::1)  0.056 ms  0.019 ms  0.006 ms
 2  2000:102::2 (2000:102::2)  0.013 ms  0.008 ms  0.008 ms
 3  2000:103::4 (2000:103::4)  0.013 ms  0.009 ms  0.009 ms

#!/bin/bash
#
#        ------------------------ N2
#         |                    |
#       ------              ------  N3  ----
#       | R1 |              | R2 |------|H2|
#       ------              ------      ----
#         |                    |
#        ------------------------ N1
#                  |
#                 ----
#                 |H1|
#                 ----
#
# N1: 2000:101::/64
# N2: 2000:102::/64
# N3: 2000:103::/64
#
# R1's host part of address: 1
# R2's host part of address: 2
# H1's host part of address: 3
# H2's host part of address: 4
#
# For example:
# the IPv6 address of R1's interface on N2 is 2000:102::1/64
#
# Nets are implemented by macvlan interfaces (bridge mode) over
# dummy interfaces.
#

# Create net namespaces
ip netns add host1
ip netns add host2
ip netns add rtr1
ip netns add rtr2

# Create nets
ip link add net1 type dummy; ip link set net1 up
ip link add net2 type dummy; ip link set net2 up
ip link add net3 type dummy; ip link set net3 up

# Add interfaces to net1, move them to their nemaspaces
ip link add link net1 dev host1net1 type macvlan mode bridge
ip link set host1net1 netns host1
ip link add link net1 dev rtr1net1 type macvlan mode bridge
ip link set rtr1net1 netns rtr1
ip link add link net1 dev rtr2net1 type macvlan mode bridge
ip link set rtr2net1 netns rtr2

# Add interfaces to net2, move them to their nemaspaces
ip link add link net2 dev rtr1net2 type macvlan mode bridge
ip link set rtr1net2 netns rtr1
ip link add link net2 dev rtr2net2 type macvlan mode bridge
ip link set rtr2net2 netns rtr2

# Add interfaces to net3, move them to their nemaspaces
ip link add link net3 dev rtr2net3 type macvlan mode bridge
ip link set rtr2net3 netns rtr2
ip link add link net3 dev host2net3 type macvlan mode bridge
ip link set host2net3 netns host2

# Configure interfaces and routes in host1
ip netns exec host1 ip link set lo up
ip netns exec host1 ip link set host1net1 up
ip netns exec host1 ip -6 addr add 2000:101::3/64 dev host1net1
ip netns exec host1 ip -6 route add default via 2000:101::1

# Configure interfaces and routes in rtr1
ip netns exec rtr1 ip link set lo up
ip netns exec rtr1 ip link set rtr1net1 up
ip netns exec rtr1 ip -6 addr add 2000:101::1/64 dev rtr1net1
ip netns exec rtr1 ip link set rtr1net2 up
ip netns exec rtr1 ip -6 addr add 2000:102::1/64 dev rtr1net2
ip netns exec rtr1 ip -6 route add default via 2000:102::2
ip netns exec rtr1 sysctl net.ipv6.conf.all.forwarding=1

# Configure interfaces and routes in rtr2
ip netns exec rtr2 ip link set lo up
ip netns exec rtr2 ip link set rtr2net1 up
ip netns exec rtr2 ip -6 addr add 2000:101::2/64 dev rtr2net1
ip netns exec rtr2 ip link set rtr2net2 up
ip netns exec rtr2 ip -6 addr add 2000:102::2/64 dev rtr2net2
ip netns exec rtr2 ip link set rtr2net3 up
ip netns exec rtr2 ip -6 addr add 2000:103::2/64 dev rtr2net3
ip netns exec rtr2 sysctl net.ipv6.conf.all.forwarding=1

# Configure interfaces and routes in host2
ip netns exec host2 ip link set lo up
ip netns exec host2 ip link set host2net3 up
ip netns exec host2 ip -6 addr add 2000:103::4/64 dev host2net3
ip netns exec host2 ip -6 route add default via 2000:103::2

# Ping host2 from host1
ip netns exec host1 ping6 -c5 2000:103::4

# Traceroute host2 from host1
ip netns exec host1 traceroute6 2000:103::4

# Delete nets
ip link del net3
ip link del net2
ip link del net1

# Delete namespaces
ip netns del rtr2
ip netns del rtr1
ip netns del host2
ip netns del host1

Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Original-patch-by: Honggang Xu <hxu@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As mentioned in commit e95584a8 ("tipc: fix unlimited bundling of
small messages"), the current message bundling algorithm is inefficient
that can generate bundles of only one payload message, that causes
unnecessary overheads for both the sender and receiver.

This commit re-designs the 'tipc_msg_make_bundle()' function (now named
as 'tipc_msg_try_bundle()'), so that when a message comes at the first
place, we will just check & keep a reference to it if the message is
suitable for bundling. The message buffer will be put into the link
backlog queue and processed as normal. Later on, when another one comes
we will make a bundle with the first message if possible and so on...
This way, a bundle if really needed will always consist of at least two
payload messages. Otherwise, we let the first buffer go its way without
any need of bundling, so reduce the overheads to zero.

Moreover, since now we have both the messages in hand, we can even
optimize the 'tipc_msg_bundle()' function, make bundle of a very large
(size ~ MSS) and small messages which is not with the current algorithm
e.g. [1400-byte message] + [10-byte message] (MTU = 1500).

Acked-by: Ying Xue <ying.xue@windreiver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Even with icmp_errors_use_inbound_ifaddr set, traceroute returns the
primary address of the interface the packet was received on, even if
the path goes through a secondary address. In the example:

                    1.0.3.1/24
 ---- 1.0.1.3/24    1.0.1.1/24 ---- 1.0.2.1/24    1.0.2.4/24 ----
 |H1|--------------------------|R1|--------------------------|H2|
 ----            N1            ----            N2            ----

where 1.0.3.1/24 is R1's primary address on N1, traceroute from
H1 to H2 returns:

traceroute to 1.0.2.4 (1.0.2.4), 30 hops max, 60 byte packets
 1  1.0.3.1 (1.0.3.1)  0.018 ms  0.006 ms  0.006 ms
 2  1.0.2.4 (1.0.2.4)  0.021 ms  0.007 ms  0.007 ms

After applying this patch, it returns:

traceroute to 1.0.2.4 (1.0.2.4), 30 hops max, 60 byte packets
 1  1.0.1.1 (1.0.1.1)  0.033 ms  0.007 ms  0.006 ms
 2  1.0.2.4 (1.0.2.4)  0.011 ms  0.007 ms  0.007 ms

Original-patch-by: Bill Fenner <fenner@arista.com>
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tonghao Zhang says:

====================
optimize openvswitch flow looking up

This series patch optimize openvswitch for performance or simplify
codes.

Patch 1, 2, 4: Port Pravin B Shelar patches to
linux upstream with little changes.

Patch 5, 6, 7: Optimize the flow looking up and
simplify the flow hash.

Patch 8, 9: are bugfix.

The performance test is on Intel Xeon E5-2630 v4.
The test topology is show as below:

+-----------------------------------+
|   +---------------------------+   |
|   | eth0   ovs-switch    eth1 |   | Host0
|   +---------------------------+   |
+-----------------------------------+
      ^                       |
      |                       |
      |                       |
      |                       |
      |                       v
+-----+----+             +----+-----+
| netperf  | Host1       | netserver| Host2
+----------+             +----------+

We use netperf send the 64B packets, and insert 255+ flow-mask:
$ ovs-dpctl add-flow ovs-switch "in_port(1),eth(dst=00:01:00:00:00:00/ff:ff:ff:ff:ff:01),eth_type(0x0800),ipv4(frag=no)" 2
...
$ ovs-dpctl add-flow ovs-switch "in_port(1),eth(dst=00:ff:00:00:00:00/ff:ff:ff:ff:ff:ff),eth_type(0x0800),ipv4(frag=no)" 2
$
$ netperf -t UDP_STREAM -H 2.2.2.200 -l 40 -- -m 18

* Without series patch, throughput 8.28Mbps
* With series patch, throughput 46.05Mbps

v6:
some coding style fixes

v5:
rewrite patch 8, release flow-mask when freeing flow

v4:
access ma->count with READ_ONCE/WRITE_ONCE API. More information,
see patch 5 comments.

v3:
update ma point when realloc mask_array in patch 5

v2:
simplify codes. e.g. use kfree_rcu instead of call_rcu
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

use the specified functions to init resource.

Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Tested-by: Greg Rose <gvrose8192@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Unlocking of a not locked mutex is not allowed.
Other kernel thread may be in critical section while
we unlock it because of setting user_feature fail.

Fixes: 95a7233c ("net: openvswitch: Set OvS recirc_id from tc chain index")
Cc: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Tested-by: Greg Rose <gvrose8192@gmail.com>
Acked-by: William Tu <u9012063@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

When we destroy the flow tables which may contain the flow_mask,
so release the flow mask struct.

Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Tested-by: Greg Rose <gvrose8192@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The most case *index < ma->max, and flow-mask is not NULL.
We add un/likely for performance.

Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Tested-by: Greg Rose <gvrose8192@gmail.com>
Acked-by: William Tu <u9012063@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>