When tearing down a net namespace, ipv4 mr_table structures are freed
without first deactivating their timers. This can result in a crash in
run_timer_softirq.
This patch mimics the corresponding behaviour in ipv6.
Locking and synchronization seem to be adequate.
We are about to kfree mrt, so existing code should already make sure that
no other references to mrt are pending or can be created by incoming traffic.
The functions invoked here do not cause new references to mrt or other
race conditions to be created.
Invoking del_timer_sync guarantees that ipmr_expire_timer is inactive.
Both ipmr_expire_process (whose completion we may have to wait in
del_timer_sync) and mroute_clean_tables internally use mfc_unres_lock
or other synchronizations when needed, and they both only modify mrt.

Tested in Linux 3.4.8.

Signed-off-by: Francesco Ruggeri <fruggeri@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With a low enough MSS on the link partner and TSO enabled locally, the
networking stack can periodically send a very large (e.g.  64KB) TCP
message for which the driver will attempt to use more Tx descriptors than
are available by default in the Tx ring.  This is due to a workaround in
the code that imposes a limit of only 4 MSS-sized segments per descriptor
which appears to be a carry-over from the older e1000 driver and may be
applicable only to some older PCI or PCIx parts which are not supported in
e1000e.  When the driver gets a message that is too large to fit across the
configured number of Tx descriptors, it stops the upper stack from queueing
any more and gets stuck in this state.  After a timeout, the upper stack
assumes the adapter is hung and calls the driver to reset it.

Remove the unnecessary limitation of using up to only 4 MSS-sized segments
per Tx descriptor, and put in a hard failure test to catch when attempting
to check for message sizes larger than would fit in the whole Tx ring.
Refactor the remaining logic that limits the size of data per Tx descriptor
from a seemingly arbitrary 8KB to a limit based on the dynamic size of the
Tx packet buffer as described in the hardware specification.

Also, fix the logic in the check for space in the Tx ring for the next
largest possible packet after the current one has been successfully queued
for transmit, and use the appropriate defines for default ring sizes in
e1000_probe instead of magic values.

This issue goes back to the introduction of e1000e in 2.6.24 when it was
split off from e1000.

Reported-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: Stable <stable@vger.kernel.org> [2.6.24+]
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Avoid to use synchronize_rcu in l2tp_tunnel_free because context may be
atomic.

Signed-off-by: Dmitry Kozlov <xeb@mail.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit -
"b852b720 gianfar: fix bug caused by
87c288c6

"
disables by default (on mac init) the hw vlan tag insertion.
The "features" flags were not updated to reflect this, and
"ethtool -K" shows tx-vlan-offload to be "on" by default.

Cc: Sebastian Poehn <sebastian.poehn@belden.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

I'm slightly concerned by the "only in exceptional circumstances"
comment on __pskb_pull_tail but the structure of an skb just created
by netfront shouldn't hit any of the especially slow cases.

This approach still does slightly more work than the old way, since if
we pull up the entire first frag we now have to shuffle everything
down where before we just received into the right place in the first
place.

Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: xen-devel@lists.xensource.com
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Against -net.

In the patch "netpoll: re-enable irq in poll_napi()", I tried to
fix the following warning:

[100718.051041] ------------[ cut here ]------------
[100718.051048] WARNING: at kernel/softirq.c:159 local_bh_enable_ip+0x7d/0xb0()
(Not tainted)
[100718.051049] Hardware name: ProLiant BL460c G7
...
[100718.051068] Call Trace:
[100718.051073]  [<ffffffff8106b747>] ? warn_slowpath_common+0x87/0xc0
[100718.051075]  [<ffffffff8106b79a>] ? warn_slowpath_null+0x1a/0x20
[100718.051077]  [<ffffffff810747ed>] ? local_bh_enable_ip+0x7d/0xb0
[100718.051080]  [<ffffffff8150041b>] ? _spin_unlock_bh+0x1b/0x20
[100718.051085]  [<ffffffffa00ee974>] ? be_process_mcc+0x74/0x230 [be2net]
[100718.051088]  [<ffffffffa00ea68c>] ? be_poll_tx_mcc+0x16c/0x290 [be2net]
[100718.051090]  [<ffffffff8144fe76>] ? netpoll_poll_dev+0xd6/0x490
[100718.051095]  [<ffffffffa01d24a5>] ? bond_poll_controller+0x75/0x80 [bonding]
[100718.051097]  [<ffffffff8144fde5>] ? netpoll_poll_dev+0x45/0x490
[100718.051100]  [<ffffffff81161b19>] ? ksize+0x19/0x80
[100718.051102]  [<ffffffff81450437>] ? netpoll_send_skb_on_dev+0x157/0x240

by reenabling IRQ before calling ->poll, but it seems more
problems are introduced after that patch:

http://ozlabs.org/~akpm/stuff/IMG_20120824_122054.jpg
http://marc.info/?l=linux-netdev&m=134563282530588&w=2



So it is safe to fix be2net driver code directly.

This patch reverts the offending commit and fixes be_poll() by
avoid disabling BH there, this is okay because be_poll()
can be called either by poll_napi() which already disables
IRQ, or by net_rx_action() which already disables BH.

Reported-by: Andrew Morton <akpm@linux-foundation.org>
Reported-by: Sylvain Munaut <s.munaut@whatever-company.com>
Cc: Sylvain Munaut <s.munaut@whatever-company.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: David Miller <davem@davemloft.net>
Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Tested-by: Sylvain Munaut <s.munaut@whatever-company.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ben Hutchings says:

====================
Simple fix for a braino.  Please also queue this for the 3.4 and 3.5
stable series.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Marc Kleine-Budde says:

====================
here are two fixes for the v3.6 release cycle. Alexey Khoroshilov submitted a
fix for a memory leak in the softing driver (in softing_load_fw()) in case a
krealloc() fails. Sven Schmitt fixed the misuse of the IRQF_SHARED flag in the
irq resouce of the sja1000 platform driver, now the correct flag is used. There
are no mainline users of this feature which need to be converted.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

John W. Linville says:

====================
This batch of fixes is intended for 3.6...

Johannes Berg gives us a pair of iwlwifi fixes.  One corrects some
improperly defined ifdefs that lead to crashes and BUG_ONs.  The other
prevents attempts to read SRAM for devices that aren't actually started.

Julia Lawall provides an ipw2100 fix to properly set the return code
from a function call before testing it! :-)

Thomas Huehn corrects the improper use of a constant related to a power
setting in ath5k.

Thomas Pedersen offers a mac80211 fix to properly handle destination
addresses of unicast frames passing though a mesh gate.

Vladimir Zapolskiy provides a brcmsmac fix to properly mark the
interface state when the device goes down.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

The cwnd reduction in fast recovery is based on the number of packets
newly delivered per ACK. For non-sack connections every DUPACK
signifies a packet has been delivered, but the sender mistakenly
skips counting them for cwnd reduction.

The fix is to compute newly_acked_sacked after DUPACKs are accounted
in sacked_out for non-sack connections.

Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Nandita Dukkipati <nanditad@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Non-root user-space processes can send Netlink messages to other
processes that are well-known for being subscribed to Netlink
asynchronous notifications. This allows ilegitimate non-root
process to send forged messages to Netlink subscribers.

The userspace process usually verifies the legitimate origin in
two ways:

a) Socket credentials. If UID != 0, then the message comes from
   some ilegitimate process and the message needs to be dropped.

b) Netlink portID. In general, portID == 0 means that the origin
   of the messages comes from the kernel. Thus, discarding any
   message not coming from the kernel.

However, ctnetlink sets the portID in event messages that has
been triggered by some user-space process, eg. conntrack utility.
So other processes subscribed to ctnetlink events, eg. conntrackd,
know that the event was triggered by some user-space action.

Neither of the two ways to discard ilegitimate messages coming
from non-root processes can help for ctnetlink.

This patch adds capability validation in case that dst_pid is set
in netlink_sendmsg(). This approach is aggressive since existing
applications using any Netlink bus to deliver messages between
two user-space processes will break. Note that the exception is
NETLINK_USERSOCK, since it is reserved for netlink-to-netlink
userspace communication.

Still, if anyone wants that his Netlink bus allows netlink-to-netlink
userspace, then they can set NL_NONROOT_SEND. However, by default,
I don't think it makes sense to allow to use NETLINK_ROUTE to
communicate two processes that are sending no matter what information
that is not related to link/neighbouring/routing. They should be using
NETLINK_USERSOCK instead for that.

Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds "#ifndef __<header>_H" for protecting header from double
inclusion.

Signed-off-by: Rayagond Kokatanur <rayagond@vayavyalabs.com>
Hacked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Multicast traffic allocates dst with DST_NOCACHE, but dst is
not inserted into rt_uncached_list.

This slowdown multicast workloads on SMP because rt_uncached_lock is
contended.

Change the test before taking the lock to actually check the dst
was inserted into rt_uncached_list.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem

The sja1000 platform driver wrongly assumes that a shared IRQ is indicated
with the IRQF_SHARED flag in irq resource flags. This patch changes the
driver to handle the correct flag IORESOURCE_IRQ_SHAREABLE instead.

There are no mainline users of the platform driver which wrongly make use
of IRQF_SHARED.

Signed-off-by: Sven Schmitt <sven.schmitt@volkswagen.de>
Acked-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Do not leak memory by updating pointer with potentially NULL realloc return value.

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

ETHTOOL_GRXCLSRULE returns filters for a TCP/IPv4 or UDP/IPv4 4-tuple
with source and destination swapped.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>

cc: Eric Leblond <eric@regit.org>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes the name of the macro used to mask the
mmc interrupt: erroneously it was used: MMC_DEFAUL_MASK.

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Erroneously the DWMAC_CORE_3_40 was set to 34 instead of 0x34.
This can generate problems when run on old chips because
the driver assumes that there are the extra 16 regs available
for perfect filtering.

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Gianni Antoniazzi <gianni.antoniazzi-ext@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sylvain Munault reported following info :

 - TCP connection get "stuck" with data in send queue when doing
   "large" transfers ( like typing 'ps ax' on a ssh connection )
 - Only happens on path where the PMTU is lower than the MTU of
   the interface
 - Is not present right after boot, it only appears 10-20min after
   boot or so. (and that's inside the _same_ TCP connection, it works
   fine at first and then in the same ssh session, it'll get stuck)
 - Definitely seems related to fragments somehow since I see a router
   sending ICMP message saying fragmentation is needed.
 - Exact same setup works fine with kernel 3.5.1

Problem happens when the 10 minutes (ip_rt_mtu_expires) expiration
period is over.

ip_rt_update_pmtu() calls dst_set_expires() to rearm a new expiration,
but dst_set_expires() does nothing because dst.expires is already set.

It seems we want to set the expires field to a new value, regardless
of prior one.

With help from Julian Anastasov.

Reported-by: Sylvain Munaut <s.munaut@whatever-company.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
CC: Julian Anastasov <ja@ssi.bg>
Tested-by: Sylvain Munaut <s.munaut@whatever-company.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change marks interface as down on reset, otherwise the driver can't
reinitialize itself properly.

Without the change a transient problem turns out to be critical and leads
to inavailability to reset the driver without brcmsmac module unload/load
cycle:

    ieee80211 phy0: wl0: PSM microcode watchdog fired at 5993 (seconds). Resetting.
    brcms_c_dpc : PSM Watchdog, chipid 0xa8d9, chiprev 0x1
    ieee80211 phy0: wl0: fatal error, reinitializing
    ieee80211 phy0: Hardware restart was requested
    ieee80211 phy0: brcms_ops_start: brcms_up() returned -19

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Pull drm fixes from Dave Airlie:
 "Intel: edid fixes, power consumption fix, s/r fix, haswell fix

  Radeon: BIOS loading fixes for UEFI and Thunderbolt machines, better
  MSAA validation, lockup timeout fixes, modesetting fixes

  One udl dpms fix, one vmwgfx fix, a couple of trivial core changes.

  There is an export added to ACPI as part of the radeon bios fixes.

  I've also included the fbcon flashing cursor vs deinit race fix, that
  seems the simplest place to start"

Trivial conflict in drivers/video/console/fbcon.c due to me having
already applied the fbcon flashing cursor vs deinit race fix, and Dave
had added a comment in there too.

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (22 commits)
  fbcon: fix race condition between console lock and cursor timer (v1.1)
  drm: Add missing static storage class specifiers in drm_proc.c file
  drm/udl: dpms off the crtc when disabled.
  drm: Remove two unused fields from struct drm_display_mode
  drm: stop vmgfx driver explosion
  drm/radeon/ss: use num_crtc rather than hardcoded 6
  Revert "drm/radeon: fix bo creation retry path"
  drm/i915: use hsw rps tuning values everywhere on gen6+
  drm/radeon: split ATRM support out from the ATPX handler (v3)
  drm/radeon: convert radeon vfct code to use acpi_get_table_with_size
  ACPI: export symbol acpi_get_table_with_size
  drm/radeon: implement ACPI VFCT vbios fetch (v3)
  drm/radeon/kms: extend the Fujitsu D3003-S2 board connector quirk to cover later silicon stepping
  drm/radeon: fix checking of MSAA renderbuffers on r600-r700
  drm/radeon: allow CMASK and FMASK in the CS checker on r600-r700
  drm/radeon: init lockup timeout on ring init
  drm/radeon: avoid turning off spread spectrum for used pll
  drm/i915: fall back to bit-banging if GMBUS fails in CRT EDID reads
  drm/i915: extract connector update from intel_ddc_get_modes() for reuse
  drm/i915: fix hsw uncached pte
  ...

Pull SCSI target fixes from Nicholas Bellinger:
 "The executive summary includes:

   - Post-merge review comments for tcm_vhost (MST + nab)
   - Avoid debugging overhead when not debugging for tcm-fc(FCoE) (MDR)
   - Fix NULL pointer dereference bug on alloc_page failulre (Yi Zou)
   - Fix REPORT_LUNs regression bug with pSCSI export (AlexE + nab)
   - Fix regression bug with handling of zero-length data CDBs (nab)
   - Fix vhost_scsi_target structure alignment (MST)

  Thanks again to everyone who contributed a bugfix patch, gave review
  feedback on tcm_vhost code, and/or reported a bug during their own
  testing over the last weeks.

  There is one other outstanding bug reported by Roland recently related
  to SCSI transfer length overflow handling, for which the current
  proposed bugfix has been left in queue pending further testing with
  other non iscsi-target based fabric drivers.

  As the patch is verified with loopback (local SGL memory from SCSI
  LLD) + tcm_qla2xxx (TCM allocated SGL memory mapped to PCI HW) fabric
  ports, it will be included into the next 3.6-rc-fixes PULL request."

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  target: Remove unused se_cmd.cmd_spdtl
  tcm_fc: rcu_deref outside rcu lock/unlock section
  tcm_vhost: Fix vhost_scsi_target structure alignment
  target: Fix regression bug with handling of zero-length data CDBs
  target/pscsi: Fix bug with REPORT_LUNs handling for SCSI passthrough
  tcm_vhost: Change vhost_scsi_target->vhost_wwpn to char *
  target: fix NULL pointer dereference bug alloc_page() fails to get memory
  tcm_fc: Avoid debug overhead when not debugging
  tcm_vhost: Post-merge review changes requested by MST
  tcm_vhost: Fix incorrect IS_ERR() usage in vhost_scsi_map_iov_to_sgl

Pull i2c-embedded fixes from Wolfram Sang:
 "Some bugfixes for the "embedded" part of the I2C subsystem.  The fixes
  affect mostly drivers which have been largely reworked lately and
  where regressions appeared."

* 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux:
  i2c: tegra: protect suspend/resume callbacks with CONFIG_PM_SLEEP
  i2c: diolan-u2c: Fix master_xfer return code
  I2C: OMAP: xfer: fix runtime PM get/put balance on error
  i2c: nomadik: Add default configuration into the Nomadik I2C driver

Pull pwm fixes from Thierry Reding:
 "These patches fix the Samsung PWM driver and perform some minor
  cleanups like fixing checkpatch and sparse warnings.

  Two redundant error messages are removed and the Kconfig help text for
  the PWM subsystem is made more descriptive."

* tag 'for-3.6-rc3' of git://gitorious.org/linux-pwm/linux-pwm:
  pwm: Improve Kconfig help text
  pwm: core: Fix coding style issues
  pwm: vt8500: Fix coding style issue
  pwm: Remove a redundant error message when devm_request_and_ioremap fails
  pwm: samsung: add missing device pointer to struct pwm_chip
  pwm: Add missing static storage class specifiers in core.c file

Pull ceph fixes from Sage Weil:
 "Jim's fix closes a narrow race introduced with the msgr changes.  One
  fix resolves problems with debugfs initialization that Yan found when
  multiple client instances are created (e.g., two clusters mounted, or
  rbd + cephfs), another one fixes problems with mounting a nonexistent
  server subdirectory, and the last one fixes a divide by zero error
  from unsanitized ioctl input that Dan Carpenter found."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  ceph: avoid divide by zero in __validate_layout()
  libceph: avoid truncation due to racing banners
  ceph: tolerate (and warn on) extraneous dentry from mds
  libceph: delay debugfs initialization until we learn global_id

Pull NFS client bugfixes from Trond Myklebust:
 - NFSv3 mounts need to fail if the FSINFO rpc call fails
 - Ensure that the NFS commit cache gets torn down when we unload the
   NFS module.
 - Fix memory scribble issues when interrupting a LAYOUTGET rpc call
 - Fix NFSv4 legacy idmapper regressions
 - Fix issues with the NFSv4 getacl command
 - Fix a regression when using the legacy "mount -t nfs4"

* tag 'nfs-for-3.6-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  NFSv3: Ensure that do_proc_get_root() reports errors correctly
  NFSv4: Ensure that nfs4_alloc_client cleans up on error.
  NFS: return -ENOKEY when the upcall fails to map the name
  NFS: Clear key construction data if the idmap upcall fails
  NFSv4: Don't use private xdr_stream fields in decode_getacl
  NFSv4: Fix the acl cache size calculation
  NFSv4: Fix pointer arithmetic in decode_getacl
  NFS: Alias the nfs module to nfs4
  NFS: Fix a regression when loading the NFS v4 module
  NFSv4.1: Remove a bogus BUG_ON() in nfs4_layoutreturn_done
  pnfs-obj: Better IO pattern in case of unaligned offset
  NFS41: add pg_layout_private to nfs_pageio_descriptor
  pnfs: nfs4_proc_layoutget returns void
  pnfs: defer release of pages in layoutget
  nfs: tear down caches in nfs_init_writepagecache when allocation fails

Pull assorted fixes - mostly vfs - from Al Viro:
 "Assorted fixes, with an unexpected detour into vfio refcounting logics
  (fell out when digging in an analog of eventpoll race in there)."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  task_work: add a scheduling point in task_work_run()
  fs: fix fs/namei.c kernel-doc warnings
  eventpoll: use-after-possible-free in epoll_create1()
  vfio: grab vfio_device reference *before* exposing the sucker via fd_install()
  vfio: get rid of vfio_device_put()/vfio_group_get_device* races
  vfio: get rid of open-coding kref_put_mutex
  introduce kref_put_mutex()
  vfio: don't dereference after kfree...
  mqueue: lift mnt_want_write() outside ->i_mutex, clean up a bit

It seems commit 4a9d4b02 (switch fput to task_work_add) reintroduced
the problem addressed in commit 944be0b2

 (close_files(): add scheduling
point)

If a server process with a lot of files (say 2 million tcp sockets)
is killed, we can spend a lot of time in task_work_run() and trigger
a soft lockup.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Fix kernel-doc warnings in fs/namei.c:

Warning(fs/namei.c:360): No description found for parameter 'inode'
Warning(fs/namei.c:672): No description found for parameter 'nd'

Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc:	Alexander Viro <viro@zeniv.linux.org.uk>
Cc:	linux-fsdevel@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

As soon as we'd installed the file into descriptor table, it can
get closed by another thread.  Freeing ep in process...

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

It's not critical (anymore) since another thread closing the file will block
on ->device_lock before it gets to dropping the final reference, but it's
definitely cleaner that way...

Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

we really need to make sure that dropping the last reference happens
under the group->device_lock; otherwise a loop (under device_lock)
might find vfio_device instance that is being freed right now, has
already dropped the last reference and waits on device_lock to exclude
the sucker from the list.

Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

equivalent of
	mutex_lock(mutex);
	if (!kref_put(kref, release))
		mutex_unlock(mutex);

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

The destination address of unicast frames forwarded through a mesh gate
was being replaced with the broadcast address. Instead leave the
original destination address as the mesh DA. If the nexthop address is
not in the mpath table it will be resolved. If that fails, the frame
will be forwarded to known mesh gates.

Reported-by: Cedric Voncken <cedric.voncken@acksys.fr>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>