- Dec 08, 2019
-
-
Stefano Garzarella authored
When we receive a new packet from the guest, we check if the src_cid is correct, but we forgot to check the dst_cid. The host should accept only packets where dst_cid is equal to the host CID. Signed-off-by:
Stefano Garzarella <sgarzare@redhat.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Grygorii Strashko authored
The commit ef87f7da ("net: phy: dp83867: move dt parsing to probe") causes regression on TI dra71x-evm and dra72x-evm, where DP83867 PHY is used in "rgmii-id" mode - the networking stops working. Unfortunately, it's not enough to just move DT parsing code to .probe() as it depends on phydev->interface value, which is set to correct value abter the .probe() is completed and before calling .config_init(). So, RGMII configuration can't be loaded from DT. To fix and issue - move RGMII validation code to .config_init() - parse RGMII parameters in dp83867_of_init(), but consider them as optional. Fixes: ef87f7da ("net: phy: dp83867: move dt parsing to probe") Signed-off-by:
Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Grygorii Strashko authored
Now RX interrupt is triggered twice every time, because in cpsw_rx_interrupt() it is asked first and then disabled. So there will be pending interrupt always, when RX interrupt is enabled again in NAPI handler. Fix it by first disabling IRQ and then do ask. Fixes: 870915fe ("drivers: net: cpsw: remove disable_irq/enable_irq as irq can be masked from cpsw itself") Signed-off-by:
Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
syzbot was once again able to crash a host by setting a very small mtu on loopback device. Let's make inetdev_valid_mtu() available in include/net/ip.h, and use it in ip_setup_cork(), so that we protect both ip_append_page() and __ip_append_data() Also add a READ_ONCE() when the device mtu is read. Pairs this lockless read with one WRITE_ONCE() in __dev_set_mtu(), even if other code paths might write over this field. Add a big comment in include/linux/netdevice.h about dev->mtu needing READ_ONCE()/WRITE_ONCE() annotations. Hopefully we will add the missing ones in followup patches. [1] refcount_t: saturated; leaking memory. WARNING: CPU: 0 PID: 9464 at lib/refcount.c:22 refcount_warn_saturate+0x138/0x1f0 lib/refcount.c:22 Kernel panic - not syncing: panic_on_warn set ... CPU: 0 PID: 9464 Comm: syz-executor850 Not tainted 5.4.0-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x197/0x210 lib/dump_stack.c:118 panic+0x2e3/0x75c kernel/panic.c:221 __warn.cold+0x2f/0x3e kernel/panic.c:582 report_bug+0x289/0x300 lib/bug.c:195 fixup_bug arch/x86/kernel/traps.c:174 [inline] fixup_bug arch/x86/kernel/traps.c:169 [inline] do_error_trap+0x11b/0x200 arch/x86/kernel/traps.c:267 do_invalid_op+0x37/0x50 arch/x86/kernel/traps.c:286 invalid_op+0x23/0x30 arch/x86/entry/entry_64.S:1027 RIP: 0010:refcount_warn_saturate+0x138/0x1f0 lib/refcount.c:22 Code: 06 31 ff 89 de e8 c8 f5 e6 fd 84 db 0f 85 6f ff ff ff e8 7b f4 e6 fd 48 c7 c7 e0 71 4f 88 c6 05 56 a6 a4 06 01 e8 c7 a8 b7 fd <0f> 0b e9 50 ff ff ff e8 5c f4 e6 fd 0f b6 1d 3d a6 a4 06 31 ff 89 RSP: 0018:ffff88809689f550 EFLAGS: 00010286 RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000 RDX: 0000000000000000 RSI: ffffffff815e4336 RDI: ffffed1012d13e9c RBP: ffff88809689f560 R08: ffff88809c50a3c0 R09: fffffbfff15d31b1 R10: fffffbfff15d31b0 R11: ffffffff8ae98d87 R12: 0000000000000001 R13: 0000000000040100 R14: ffff888099041104 R15: ffff888218d96e40 refcount_add include/linux/refcount.h:193 [inline] skb_set_owner_w+0x2b6/0x410 net/core/sock.c:1999 sock_wmalloc+0xf1/0x120 net/core/sock.c:2096 ip_append_page+0x7ef/0x1190 net/ipv4/ip_output.c:1383 udp_sendpage+0x1c7/0x480 net/ipv4/udp.c:1276 inet_sendpage+0xdb/0x150 net/ipv4/af_inet.c:821 kernel_sendpage+0x92/0xf0 net/socket.c:3794 sock_sendpage+0x8b/0xc0 net/socket.c:936 pipe_to_sendpage+0x2da/0x3c0 fs/splice.c:458 splice_from_pipe_feed fs/splice.c:512 [inline] __splice_from_pipe+0x3ee/0x7c0 fs/splice.c:636 splice_from_pipe+0x108/0x170 fs/splice.c:671 generic_splice_sendpage+0x3c/0x50 fs/splice.c:842 do_splice_from fs/splice.c:861 [inline] direct_splice_actor+0x123/0x190 fs/splice.c:1035 splice_direct_to_actor+0x3b4/0xa30 fs/splice.c:990 do_splice_direct+0x1da/0x2a0 fs/splice.c:1078 do_sendfile+0x597/0xd00 fs/read_write.c:1464 __do_sys_sendfile64 fs/read_write.c:1525 [inline] __se_sys_sendfile64 fs/read_write.c:1511 [inline] __x64_sys_sendfile64+0x1dd/0x220 fs/read_write.c:1511 do_syscall_64+0xfa/0x790 arch/x86/entry/common.c:294 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x441409 Code: e8 ac e8 ff ff 48 83 c4 18 c3 0f 1f 80 00 00 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 eb 08 fc ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007fffb64c4f78 EFLAGS: 00000246 ORIG_RAX: 0000000000000028 RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 0000000000441409 RDX: 0000000000000000 RSI: 0000000000000006 RDI: 0000000000000005 RBP: 0000000000073b8a R08: 0000000000000010 R09: 0000000000000010 R10: 0000000000010001 R11: 0000000000000246 R12: 0000000000402180 R13: 0000000000402210 R14: 0000000000000000 R15: 0000000000000000 Kernel Offset: disabled Rebooting in 86400 seconds.. Fixes: 1470ddf7 ("inet: Remove explicit write references to sk/inet in ip_append_data") Signed-off-by:
Eric Dumazet <edumazet@google.com> Reported-by:
syzbot <syzkaller@googlegroups.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Cong Wang authored
After pskb_may_pull() we should always refetch the header pointers from the skb->data in case it got reallocated. In gre_parse_header(), the erspan header is still fetched from the 'options' pointer which is fetched before pskb_may_pull(). Found this during code review of a KMSAN bug report. Fixes: cb73ee40 ("net: ip_gre: use erspan key field for tunnel lookup") Cc: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by:
Cong Wang <xiyou.wangcong@gmail.com> Acked-by:
Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Acked-by:
William Tu <u9012063@gmail.com> Reviewed-by:
Simon Horman <simon.horman@netronome.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Aditya Pakki authored
Passing NULL to pppoe_pernet causes a crash via BUG_ON. Dereferencing net in net_generici() also has the same effect. This patch removes the redundant BUG_ON check on the same parameter. Signed-off-by:
Aditya Pakki <pakki001@umn.edu> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
- Dec 07, 2019
-
-
David S. Miller authored
Guillaume Nault says: ==================== tcp: fix handling of stale syncookies timestamps The synflood timestamps (->ts_recent_stamp and ->synq_overflow_ts) are only refreshed when the syncookie protection triggers. Therefore, their value can become very far apart from jiffies if no synflood happens for a long time. If jiffies grows too much and wraps while the synflood timestamp isn't refreshed, then time_after32() might consider the later to be in the future. This can trick tcp_synq_no_recent_overflow() into returning erroneous values and rejecting valid ACKs. Patch 1 handles the case of ACKs using legitimate syncookies. Patch 2 handles the case of stray ACKs. Patch 3 annotates lockless timestamp operations with READ_ONCE() and WRITE_ONCE(). Changes from v3: - Fix description of time_between32() (found by Eric Dumazet). - Use more accurate Fixes tag in patch 3 (suggested by Eric Dumazet). Changes from v2: - Define and use time_between32() instead of a pair of time_before32/time_after32 (suggested by Eric Dumazet). - Use 'last_overflow - HZ' as lower bound in tcp_synq_no_recent_overflow(), to accommodate for concurrent timestamp updates (found by Eric Dumazet). - Add a third patch to annotate lockless accesses to .ts_recent_stamp. Changes from v1: - Initialising timestamps at socket creation time is not enough because jiffies wraps in 24 days with HZ=1000 (Eric Dumazet). Handle stale timestamps in tcp_synq_overflow() and tcp_synq_no_recent_overflow() instead. - Rework commit description. - Add a second patch to handle the case of stray ACKs. ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Guillaume Nault authored
Syncookies borrow the ->rx_opt.ts_recent_stamp field to store the timestamp of the last synflood. Protect them with READ_ONCE() and WRITE_ONCE() since reads and writes aren't serialised. Use of .rx_opt.ts_recent_stamp for storing the synflood timestamp was introduced by a0f82f64 ("syncookies: remove last_synq_overflow from struct tcp_sock"). But unprotected accesses were already there when timestamp was stored in .last_synq_overflow. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
Guillaume Nault <gnault@redhat.com> Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Guillaume Nault authored
When no synflood occurs, the synflood timestamp isn't updated. Therefore it can be so old that time_after32() can consider it to be in the future. That's a problem for tcp_synq_no_recent_overflow() as it may report that a recent overflow occurred while, in fact, it's just that jiffies has grown past 'last_overflow' + TCP_SYNCOOKIE_VALID + 2^31. Spurious detection of recent overflows lead to extra syncookie verification in cookie_v[46]_check(). At that point, the verification should fail and the packet dropped. But we should have dropped the packet earlier as we didn't even send a syncookie. Let's refine tcp_synq_no_recent_overflow() to report a recent overflow only if jiffies is within the [last_overflow, last_overflow + TCP_SYNCOOKIE_VALID] interval. This way, no spurious recent overflow is reported when jiffies wraps and 'last_overflow' becomes in the future from the point of view of time_after32(). However, if jiffies wraps and enters the [last_overflow, last_overflow + TCP_SYNCOOKIE_VALID] interval (with 'last_overflow' being a stale synflood timestamp), then tcp_synq_no_recent_overflow() still erroneously reports an overflow. In such cases, we have to rely on syncookie verification to drop the packet. We unfortunately have no way to differentiate between a fresh and a stale syncookie timestamp. In practice, using last_overflow as lower bound is problematic. If the synflood timestamp is concurrently updated between the time we read jiffies and the moment we store the timestamp in 'last_overflow', then 'now' becomes smaller than 'last_overflow' and tcp_synq_no_recent_overflow() returns true, potentially dropping a valid syncookie. Reading jiffies after loading the timestamp could fix the problem, but that'd require a memory barrier. Let's just accommodate for potential timestamp growth instead and extend the interval using 'last_overflow - HZ' as lower bound. Signed-off-by:
Guillaume Nault <gnault@redhat.com> Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Guillaume Nault authored
If no synflood happens for a long enough period of time, then the synflood timestamp isn't refreshed and jiffies can advance so much that time_after32() can't accurately compare them any more. Therefore, we can end up in a situation where time_after32(now, last_overflow + HZ) returns false, just because these two values are too far apart. In that case, the synflood timestamp isn't updated as it should be, which can trick tcp_synq_no_recent_overflow() into rejecting valid syncookies. For example, let's consider the following scenario on a system with HZ=1000: * The synflood timestamp is 0, either because that's the timestamp of the last synflood or, more commonly, because we're working with a freshly created socket. * We receive a new SYN, which triggers synflood protection. Let's say that this happens when jiffies == 2147484649 (that is, 'synflood timestamp' + HZ + 2^31 + 1). * Then tcp_synq_overflow() doesn't update the synflood timestamp, because time_after32(2147484649, 1000) returns false. With: - 2147484649: the value of jiffies, aka. 'now'. - 1000: the value of 'last_overflow' + HZ. * A bit later, we receive the ACK completing the 3WHS. But cookie_v[46]_check() rejects it because tcp_synq_no_recent_overflow() says that we're not under synflood. That's because time_after32(2147484649, 120000) returns false. With: - 2147484649: the value of jiffies, aka. 'now'. - 120000: the value of 'last_overflow' + TCP_SYNCOOKIE_VALID. Of course, in reality jiffies would have increased a bit, but this condition will last for the next 119 seconds, which is far enough to accommodate for jiffie's growth. Fix this by updating the overflow timestamp whenever jiffies isn't within the [last_overflow, last_overflow + HZ] range. That shouldn't have any performance impact since the update still happens at most once per second. Now we're guaranteed to have fresh timestamps while under synflood, so tcp_synq_no_recent_overflow() can safely use it with time_after32() in such situations. Stale timestamps can still make tcp_synq_no_recent_overflow() return the wrong verdict when not under synflood. This will be handled in the next patch. For 64 bits architectures, the problem was introduced with the conversion of ->tw_ts_recent_stamp to 32 bits integer by commit cca9bab1 ("tcp: use monotonic timestamps for PAWS"). The problem has always been there on 32 bits architectures. Fixes: cca9bab1 ("tcp: use monotonic timestamps for PAWS") Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
Guillaume Nault <gnault@redhat.com> Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linuxDavid S. Miller authored
Saeed Mahameed says: ==================== Mellanox, mlx5 fixes 2019-12-05 This series introduces some fixes to mlx5 driver. Please pull and let me know if there is any problem. For -stable v4.19: ('net/mlx5e: Query global pause state before setting prio2buffer') For -stable v5.3 ('net/mlx5e: Fix SFF 8472 eeprom length') ('net/mlx5e: Fix translation of link mode into speed') ('net/mlx5e: Fix freeing flow with kfree() and not kvfree()') ('net/mlx5e: ethtool, Fix analysis of speed setting') ('net/mlx5e: Fix TXQ indices to be sequential') ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Bruno Carneiro da Cunha authored
We may have found a bug in the nxp/lpc_eth.c driver. The function platform_set_drvdata() is called twice, the second time it is called, in lpc_mii_init(), it overwrites the struct net_device which should be at pdev->dev->driver_data with pldat->mii_bus. When trying to remove the driver, in lpc_eth_drv_remove(), platform_get_drvdata() will return the pldat->mii_bus pointer and try to use it as a struct net_device pointer. This causes unregister_netdev to segfault and generate a kernel BUG. Is this reproducible? Signed-off-by:
Daniel Martinez <linux@danielsmartinez.com> Signed-off-by:
Bruno Carneiro da Cunha <brunocarneirodacunha@usp.br> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
Back in 2008, Adam Langley fixed the corner case of packets for flows having all of the following options : MD5 TS SACK Since MD5 needs 20 bytes, and TS needs 12 bytes, no sack block can be cooked from the remaining 8 bytes. tcp_established_options() correctly sets opts->num_sack_blocks to zero, but returns 36 instead of 32. This means TCP cooks packets with 4 extra bytes at the end of options, containing unitialized bytes. Fixes: 33ad798c ("tcp: options clean up") Signed-off-by:
Eric Dumazet <edumazet@google.com> Reported-by:
syzbot <syzkaller@googlegroups.com> Acked-by:
Neal Cardwell <ncardwell@google.com> Acked-by:
Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
John Hurley says: ==================== Ensure egress un/bind are relayed with indirect blocks On register and unregister for indirect blocks, a command is called that sends a bind/unbind event to the registering driver. This command assumes that the bind to indirect block will be on ingress. However, drivers such as NFP have allowed binding to clsact qdiscs as well as ingress qdiscs from mainline Linux 5.2. A clsact qdisc binds to an ingress and an egress block. Rather than assuming that an indirect bind is always ingress, modify the function names to remove the ingress tag (patch 1). In cls_api, which is used by NFP to offload TC flower, generate bind/unbind message for both ingress and egress blocks on the event of indirectly registering/unregistering from that block. Doing so mimics the behaviour of both ingress and clsact qdiscs on initialise and destroy. This now ensures that drivers such as NFP receive the correct binder type for the indirect block registration. ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
John Hurley authored
When a device is bound to a clsact qdisc, bind events are triggered to registered drivers for both ingress and egress. However, if a driver registers to such a device using the indirect block routines then it is assumed that it is only interested in ingress offload and so only replays ingress bind/unbind messages. The NFP driver supports the offload of some egress filters when registering to a block with qdisc of type clsact. However, on unregister, if the block is still active, it will not receive an unbind egress notification which can prevent proper cleanup of other registered callbacks. Modify the indirect block callback command in TC to send messages of ingress and/or egress bind depending on the qdisc in use. NFP currently supports egress offload for TC flower offload so the changes are only added to TC. Fixes: 4d12ba42 ("nfp: flower: allow offloading of matches on 'internal' ports") Signed-off-by:
John Hurley <john.hurley@netronome.com> Acked-by:
Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
John Hurley authored
With indirect blocks, a driver can register for callbacks from a device that is does not 'own', for example, a tunnel device. When registering to or unregistering from a new device, a callback is triggered to generate a bind/unbind event. This, in turn, allows the driver to receive any existing rules or to properly clean up installed rules. When first added, it was assumed that all indirect block registrations would be for ingress offloads. However, the NFP driver can, in some instances, support clsact qdisc binds for egress offload. Change the name of the indirect block callback command in flow_offload to remove the 'ingress' identifier from it. While this does not change functionality, a follow up patch will implement a more more generic callback than just those currently just supporting ingress offload. Fixes: 4d12ba42 ("nfp: flower: allow offloading of matches on 'internal' ports") Signed-off-by:
John Hurley <john.hurley@netronome.com> Acked-by:
Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jouni Hogander authored
Dev_hold has to be called always in netdev_queue_add_kobject. Otherwise usage count drops below 0 in case of failure in kobject_init_and_add. Fixes: b8eb7183 ("net-sysfs: Fix reference count leak in rx|netdev_queue_add_kobject") Reported-by:
Hulk Robot <hulkci@huawei.com> Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Cc: David Miller <davem@davemloft.net> Cc: Lukas Bulwahn <lukas.bulwahn@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Alexander Lobakin authored
Commit 43e66528 ("net-next: dsa: fix flow dissection") added an ability to override protocol and network offset during flow dissection for DSA-enabled devices (i.e. controllers shipped as switch CPU ports) in order to fix skb hashing for RPS on Rx path. However, skb_hash() and added part of code can be invoked not only on Rx, but also on Tx path if we have a multi-queued device and: - kernel is running on UP system or - XPS is not configured. The call stack in this two cases will be like: dev_queue_xmit() -> __dev_queue_xmit() -> netdev_core_pick_tx() -> netdev_pick_tx() -> skb_tx_hash() -> skb_get_hash(). The problem is that skbs queued for Tx have both network offset and correct protocol already set up even after inserting a CPU tag by DSA tagger, so calling tag_ops->flow_dissect() on this path actually only breaks flow dissection and hashing. This can be observed by adding debug prints just before and right after tag_ops->flow_dissect() call to the related block of code: Before the patch: Rx path (RPS): [ 19.240001] Rx: proto: 0x00f8, nhoff: 0 /* ETH_P_XDSA */ [ 19.244271] tag_ops->flow_dissect() [ 19.247811] Rx: proto: 0x0800, nhoff: 8 /* ETH_P_IP */ [ 19.215435] Rx: proto: 0x00f8, nhoff: 0 /* ETH_P_XDSA */ [ 19.219746] tag_ops->flow_dissect() [ 19.223241] Rx: proto: 0x0806, nhoff: 8 /* ETH_P_ARP */ [ 18.654057] Rx: proto: 0x00f8, nhoff: 0 /* ETH_P_XDSA */ [ 18.658332] tag_ops->flow_dissect() [ 18.661826] Rx: proto: 0x8100, nhoff: 8 /* ETH_P_8021Q */ Tx path (UP system): [ 18.759560] Tx: proto: 0x0800, nhoff: 26 /* ETH_P_IP */ [ 18.763933] tag_ops->flow_dissect() [ 18.767485] Tx: proto: 0x920b, nhoff: 34 /* junk */ [ 22.800020] Tx: proto: 0x0806, nhoff: 26 /* ETH_P_ARP */ [ 22.804392] tag_ops->flow_dissect() [ 22.807921] Tx: proto: 0x920b, nhoff: 34 /* junk */ [ 16.898342] Tx: proto: 0x86dd, nhoff: 26 /* ETH_P_IPV6 */ [ 16.902705] tag_ops->flow_dissect() [ 16.906227] Tx: proto: 0x920b, nhoff: 34 /* junk */ After: Rx path (RPS): [ 16.520993] Rx: proto: 0x00f8, nhoff: 0 /* ETH_P_XDSA */ [ 16.525260] tag_ops->flow_dissect() [ 16.528808] Rx: proto: 0x0800, nhoff: 8 /* ETH_P_IP */ [ 15.484807] Rx: proto: 0x00f8, nhoff: 0 /* ETH_P_XDSA */ [ 15.490417] tag_ops->flow_dissect() [ 15.495223] Rx: proto: 0x0806, nhoff: 8 /* ETH_P_ARP */ [ 17.134621] Rx: proto: 0x00f8, nhoff: 0 /* ETH_P_XDSA */ [ 17.138895] tag_ops->flow_dissect() [ 17.142388] Rx: proto: 0x8100, nhoff: 8 /* ETH_P_8021Q */ Tx path (UP system): [ 15.499558] Tx: proto: 0x0800, nhoff: 26 /* ETH_P_IP */ [ 20.664689] Tx: proto: 0x0806, nhoff: 26 /* ETH_P_ARP */ [ 18.565782] Tx: proto: 0x86dd, nhoff: 26 /* ETH_P_IPV6 */ In order to fix that we can add the check 'proto == htons(ETH_P_XDSA)' to prevent code from calling tag_ops->flow_dissect() on Tx. I also decided to initialize 'offset' variable so tagger callbacks can now safely leave it untouched without provoking a chaos. Fixes: 43e66528 ("net-next: dsa: fix flow dissection") Signed-off-by:
Alexander Lobakin <alobakin@dlink.ru> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Valentin Vidic authored
ENOTSUPP is not available in userspace, for example: setsockopt failed, 524, Unknown error 524 Signed-off-by:
Valentin Vidic <vvidic@valentin-vidic.from.hr> Acked-by:
Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
CONFIG_RETPOLINE=y made indirect calls expensive. gcc seems to add an indirect call in ____sys_recvmsg(). Rewriting the code slightly makes sure to avoid this indirection. Alternative would be to not call sock_recvmsg() and instead use security_socket_recvmsg() and sock_recvmsg_nosec(), but this is less readable IMO. Signed-off-by:
Eric Dumazet <edumazet@google.com> Cc: Paolo Abeni <pabeni@redhat.com> Cc: David Laight <David.Laight@aculab.com> Acked-by:
Paolo Abeni <pabeni@redhat.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Chuhong Yuan authored
The driver forgets to call pci_release_regions() in remove like that in probe failure. Add the missed call to fix it. Signed-off-by:
Chuhong Yuan <hslester96@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Taehee Yoo authored
In order to set/get/dump, the tipc uses the generic netlink infrastructure. So, when tipc module is inserted, init function calls genl_register_family(). After genl_register_family(), set/get/dump commands are immediately allowed and these callbacks internally use the net_generic. net_generic is allocated by register_pernet_device() but this is called after genl_register_family() in the __init function. So, these callbacks would use un-initialized net_generic. Test commands: #SHELL1 while : do modprobe tipc modprobe -rv tipc done #SHELL2 while : do tipc link list done Splat looks like: [ 59.616322][ T2788] kasan: CONFIG_KASAN_INLINE enabled [ 59.617234][ T2788] kasan: GPF could be caused by NULL-ptr deref or user memory access [ 59.618398][ T2788] general protection fault: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN PTI [ 59.619389][ T2788] CPU: 3 PID: 2788 Comm: tipc Not tainted 5.4.0+ #194 [ 59.620231][ T2788] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006 [ 59.621428][ T2788] RIP: 0010:tipc_bcast_get_broadcast_mode+0x131/0x310 [tipc] [ 59.622379][ T2788] Code: c7 c6 ef 8b 38 c0 65 ff 0d 84 83 c9 3f e8 d7 a5 f2 e3 48 8d bb 38 11 00 00 48 b8 00 00 00 00 [ 59.622550][ T2780] NET: Registered protocol family 30 [ 59.624627][ T2788] RSP: 0018:ffff88804b09f578 EFLAGS: 00010202 [ 59.624630][ T2788] RAX: dffffc0000000000 RBX: 0000000000000011 RCX: 000000008bc66907 [ 59.624631][ T2788] RDX: 0000000000000229 RSI: 000000004b3cf4cc RDI: 0000000000001149 [ 59.624633][ T2788] RBP: ffff88804b09f588 R08: 0000000000000003 R09: fffffbfff4fb3df1 [ 59.624635][ T2788] R10: fffffbfff50318f8 R11: ffff888066cadc18 R12: ffffffffa6cc2f40 [ 59.624637][ T2788] R13: 1ffff11009613eba R14: ffff8880662e9328 R15: ffff8880662e9328 [ 59.624639][ T2788] FS: 00007f57d8f7b740(0000) GS:ffff88806cc00000(0000) knlGS:0000000000000000 [ 59.624645][ T2788] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 59.625875][ T2780] tipc: Started in single node mode [ 59.626128][ T2788] CR2: 00007f57d887a8c0 CR3: 000000004b140002 CR4: 00000000000606e0 [ 59.633991][ T2788] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 59.635195][ T2788] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 59.636478][ T2788] Call Trace: [ 59.637025][ T2788] tipc_nl_add_bc_link+0x179/0x1470 [tipc] [ 59.638219][ T2788] ? lock_downgrade+0x6e0/0x6e0 [ 59.638923][ T2788] ? __tipc_nl_add_link+0xf90/0xf90 [tipc] [ 59.639533][ T2788] ? tipc_nl_node_dump_link+0x318/0xa50 [tipc] [ 59.640160][ T2788] ? mutex_lock_io_nested+0x1380/0x1380 [ 59.640746][ T2788] tipc_nl_node_dump_link+0x4fd/0xa50 [tipc] [ 59.641356][ T2788] ? tipc_nl_node_reset_link_stats+0x340/0x340 [tipc] [ 59.642088][ T2788] ? __skb_ext_del+0x270/0x270 [ 59.642594][ T2788] genl_lock_dumpit+0x85/0xb0 [ 59.643050][ T2788] netlink_dump+0x49c/0xed0 [ 59.643529][ T2788] ? __netlink_sendskb+0xc0/0xc0 [ 59.644044][ T2788] ? __netlink_dump_start+0x190/0x800 [ 59.644617][ T2788] ? __mutex_unlock_slowpath+0xd0/0x670 [ 59.645177][ T2788] __netlink_dump_start+0x5a0/0x800 [ 59.645692][ T2788] genl_rcv_msg+0xa75/0xe90 [ 59.646144][ T2788] ? __lock_acquire+0xdfe/0x3de0 [ 59.646692][ T2788] ? genl_family_rcv_msg_attrs_parse+0x320/0x320 [ 59.647340][ T2788] ? genl_lock_dumpit+0xb0/0xb0 [ 59.647821][ T2788] ? genl_unlock+0x20/0x20 [ 59.648290][ T2788] ? genl_parallel_done+0xe0/0xe0 [ 59.648787][ T2788] ? find_held_lock+0x39/0x1d0 [ 59.649276][ T2788] ? genl_rcv+0x15/0x40 [ 59.649722][ T2788] ? lock_contended+0xcd0/0xcd0 [ 59.650296][ T2788] netlink_rcv_skb+0x121/0x350 [ 59.650828][ T2788] ? genl_family_rcv_msg_attrs_parse+0x320/0x320 [ 59.651491][ T2788] ? netlink_ack+0x940/0x940 [ 59.651953][ T2788] ? lock_acquire+0x164/0x3b0 [ 59.652449][ T2788] genl_rcv+0x24/0x40 [ 59.652841][ T2788] netlink_unicast+0x421/0x600 [ ... ] Fixes: 7e436905 ("tipc: fix a slab object leak") Fixes: a62fbcce ("tipc: make subscriber server support net namespace") Signed-off-by:
Taehee Yoo <ap420073@gmail.com> Acked-by:
Jon Maloy <jon.maloy@ericsson.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Vladyslav Tarasiuk authored
When user runs a command like tc qdisc add dev eth1 root mqprio KASAN stack-out-of-bounds warning is emitted. Currently, NLA_ALIGN macro used in mqprio_dump provides too large buffer size as argument for nla_put and memcpy down the call stack. The flow looks like this: 1. nla_put expects exact object size as an argument; 2. Later it provides this size to memcpy; 3. To calculate correct padding for SKB, nla_put applies NLA_ALIGN macro itself. Therefore, NLA_ALIGN should not be applied to the nla_put parameter. Otherwise it will lead to out-of-bounds memory access in memcpy. Fixes: 4e8b86c0 ("mqprio: Introduce new hardware offload mode and shaper in mqprio") Signed-off-by:
Vladyslav Tarasiuk <vladyslavt@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jongsung Kim authored
Refer to the databook of DesignWare Cores Ethernet MAC Universal: 6.2.1.5 Register 4 (Transmit Descriptor List Address Register If this register is not changed when the ST bit is set to 0, then the DMA takes the descriptor address where it was stopped earlier. The stmmac_tx_err() does zero indices to Tx descriptors, but does not reset HW current Tx descriptor address. To fix inconsistency, the base address of the Tx descriptors should be rewritten before restarting Tx. Signed-off-by:
Jongsung Kim <neidhard.kim@lge.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Yangbo Lu authored
The EEE support has not been enabled on ENETC, but it may connect to a PHY which supports EEE and advertises EEE by default, while its link partner also advertises EEE. If this happens, the PHY enters low power mode when the traffic rate is low and causes packet loss. This patch disables EEE advertisement by default for any PHY that ENETC connects to, to prevent the above unwanted outcome. Signed-off-by:
Yangbo Lu <yangbo.lu@nxp.com> Reviewed-by:
Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
- Dec 06, 2019
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpfDavid S. Miller authored
Alexei Starovoitov says: ==================== pull-request: bpf 2019-12-05 The following pull-request contains BPF updates for your *net* tree. We've added 6 non-merge commits during the last 1 day(s) which contain a total of 14 files changed, 116 insertions(+), 37 deletions(-). The main changes are: 1) three selftests fixes, from Stanislav. 2) one samples fix, from Jesper. 3) one verifier fix, from Yonghong. ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Eric Biggers authored
sock_fprog_kern::len is in units of struct sock_filter, not bytes. Fixes: 3e859adf ("compat_ioctl: unify copy-in of ppp filters") Reported-by:
<syzbot+eb853b51b10f1befa0b7@syzkaller.appspotmail.com> Signed-off-by:
Eric Biggers <ebiggers@google.com> Reviewed-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Huazhong Tan says: ==================== net: hns3: fixes for -net This patchset includes misc fixes for the HNS3 ethernet driver. [patch 1/3] fixes a TX queue not restarted problem. [patch 2/3] fixes a use-after-free issue. [patch 3/3] fixes a VF ID issue for setting VF VLAN. change log: V1->V2: keeps 'ring' as parameter in hns3_nic_maybe_stop_tx() in [patch 1/3], suggestted by David. rewrites [patch 2/3]'s commit log to make it be easier to understand, suggestted by David. ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Jian Shen authored
Previously, when set VF VLAN with command "ip link set <pf name> vf <vf id> vlan <vlan id>", the VF ID 0 is handled as PF incorrectly, which should be the first VF. This patch fixes it. Fixes: 21e043cd ("net: hns3: fix set port based VLAN for PF") Signed-off-by:
Jian Shen <shenjian15@huawei.com> Signed-off-by:
Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Yunsheng Lin authored
Currently, hns3_nic_maybe_stop_tx() uses skb_copy() to linearize a SKB if the BD num required by the SKB does not meet the hardware limitation, and it linearizes the SKB by allocating a new linearized SKB and freeing the old SKB, if hns3_nic_maybe_stop_tx() returns -EBUSY because there are no enough space in the ring to send the linearized skb to hardware, the sch_direct_xmit() still hold reference to old SKB and try to retransmit the old SKB when dev_hard_start_xmit() return TX_BUSY, which may cause use after freed problem. This patch fixes it by using __skb_linearize() to linearize the SKB in hns3_nic_maybe_stop_tx(). Fixes: 51e8439f ("net: hns3: add 8 BD limit for tx flow") Signed-off-by:
Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by:
Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Yunsheng Lin authored
There is timing window between ring_space checking and netif_stop_subqueue when transmiting a SKB, and the TX BD cleaning may be executed during the time window, which may caused TX queue not restarted problem. This patch fixes it by rechecking the ring_space after netif_stop_subqueue to make sure TX queue is restarted. Also, the ring->next_to_clean is updated even when pkts is zero, because all the TX BD cleaned may be non-SKB, so it needs to check if TX queue need to be restarted. Fixes: 76ad4f0e ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC") Signed-off-by:
Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by:
Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Grygorii Strashko authored
Replace "select NET_SWITCHDEV" vs "depends on NET_SWITCHDEV" to fix Kconfig warning with CONFIG_COMPILE_TEST=y WARNING: unmet direct dependencies detected for NET_SWITCHDEV Depends on [n]: NET [=y] && INET [=n] Selected by [y]: - TI_CPSW_SWITCHDEV [=y] && NETDEVICES [=y] && ETHERNET [=y] && NET_VENDOR_TI [=y] && (ARCH_DAVINCI || ARCH_OMAP2PLUS || COMPILE_TEST [=y]) because TI_CPSW_SWITCHDEV blindly selects NET_SWITCHDEV even though INET is not set/enabled, while NET_SWITCHDEV depends on INET. Reported-by:
Randy Dunlap <rdunlap@infradead.org> Fixes: ed3525ed ("net: ethernet: ti: introduce cpsw switchdev based driver part 1 - dual-emac") Signed-off-by:
Grygorii Strashko <grygorii.strashko@ti.com> Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Parav Pandit authored
In cited commit, when prio tag mode is enabled, FTE creation fails due to missing group with valid match criteria. Hence, (a) create prio tag group metadata_prio_tag_grp when prio tag is enabled with match criteria for vlan push FTE. (b) Rename metadata_grp to metadata_allmatch_grp to reflect its purpose. Also when priority tag is enabled, delete metadata settings after deleting ingress rules, which are using it. Tide up rest of the ingress config code for unnecessary labels. Fixes: 10652f39 ("net/mlx5: Refactor ingress acl configuration") Signed-off-by:
Parav Pandit <parav@mellanox.com> Reviewed-by:
Eli Britstein <elibr@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com>
-
Aya Levin authored
When setting speed to 100G via ethtool (AN is set to off), only 25G*4 is configured while the user, who has an advanced HW which supports extended PTYS, expects also 50G*2 to be configured. With this patch, when extended PTYS mode is available, configure PTYS via extended fields. Fixes: 4b95840a ("net/mlx5e: Fix matching of speed to PRM link modes") Signed-off-by:
Aya Levin <ayal@mellanox.com> Reviewed-by:
Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com>
-
Aya Levin authored
Add a missing value in translation of PTYS ext_eth_proto_oper to its corresponding speed. When ext_eth_proto_oper bit 10 is set, ethtool shows unknown speed. With this fix, ethtool shows speed is 100G as expected. Fixes: a08b4ed1 ("net/mlx5: Add support to ext_* fields introduced in Port Type and Speed register") Signed-off-by:
Aya Levin <ayal@mellanox.com> Reviewed-by:
Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com>
-
Roi Dayan authored
It could be neigh update flow took a refcount on peer flow so sometimes we cannot release peer flow even if parent flow is being freed now. Fixes: 5a7e5bcb ("net/mlx5e: Extend tc flow struct with reference counter") Signed-off-by:
Roi Dayan <roid@mellanox.com> Reviewed-by:
Eli Britstein <elibr@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com>
-
Roi Dayan authored
Flows are allocated with kzalloc() so free with kfree(). Fixes: 04de7dda ("net/mlx5e: Infrastructure for duplicated offloading of TC flows") Signed-off-by:
Roi Dayan <roid@mellanox.com> Reviewed-by:
Eli Britstein <elibr@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com>
-
Eran Ben Elisha authored
SFF 8472 eeprom length is 512 bytes. Fix module info return value to support 512 bytes read. Fixes: ace329f4 ("net/mlx5e: ethtool, Remove unsupported SFP EEPROM high pages query") Signed-off-by:
Eran Ben Elisha <eranbe@mellanox.com> Reviewed-by:
Aya Levin <ayal@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com>
-
Huy Nguyen authored
When the user changes prio2buffer mapping while global pause is enabled, mlx5 driver incorrectly sets all active buffers (buffer that has at least one priority mapped) to lossy. Solution: If global pause is enabled, set all the active buffers to lossless in prio2buffer command. Also, add error message when buffer size is not enough to meet xoff threshold. Fixes: 0696d608 ("net/mlx5e: Receive buffer configuration") Signed-off-by:
Huy Nguyen <huyn@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com>
-
Eran Ben Elisha authored
Cited patch changed (channel index, tc) => (TXQ index) mapping to be a static one, in order to keep indices consistent when changing number of channels or TCs. For 32 channels (OOB) and 8 TCs, real num of TXQs is 256. When reducing the amount of channels to 8, the real num of TXQs will be changed to 64. This indices method is buggy: - Channel #0, TC 3, the TXQ index is 96. - Index 8 is not valid, as there is no such TXQ from driver perspective (As it represents channel #8, TC 0, which is not valid with the above configuration). As part of driver's select queue, it calls netdev_pick_tx which returns an index in the range of real number of TXQs. Depends on the return value, with the examples above, driver could have returned index larger than the real number of tx queues, or crash the kernel as it tries to read invalid address of SQ which was not allocated. Fix that by allocating sequential TXQ indices, and hold a new mapping between (channel index, tc) => (real TXQ index). This mapping will be updated as part of priv channels activation, and is used in mlx5e_select_queue to find the selected queue index. The existing indices mapping (channel_tc2txq) is no longer needed, as it is used only for statistics structures and can be calculated on run time. Delete its definintion and updates. Fixes: 8bfaf07f ("net/mlx5e: Present SW stats when state is not opened") Signed-off-by:
Eran Ben Elisha <eranbe@mellanox.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com>
-