Add the tables and config for the combo phy found on SM6350.

Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230120-sm6350-usbphy-v4-2-4d700a90ba16@fairphone.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>

Add the compatible describing the combo phy found on SM6350.

Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Link: https://lore.kernel.org/r/20230120-sm6350-usbphy-v4-1-4d700a90ba16@fairphone.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>

Remove the temporary @mask_, this may cause build warning when use clang
compiler for powerpc, but can't reproduce it when compile for arm64.
the build warning is caused by:

"warning: result of comparison of constant 18446744073709551615 with
expression of type (aka 'unsigned long') is always false
[-Wtautological-constant-out-of-range-compare]"

More information provided in below lore link.

After removing @mask_, there is a "CHECK:MACRO_ARG_REUSE" when run
checkpatch.pl, but due to @mask is constant, no reuse problem will happen.

Link: https://lore.kernel.org/lkml/202212160357.jJuesD8n-lkp@intel.com/t/
Fixes: 84513ecc

 ("phy: mediatek: fix build warning of FIELD_PREP()")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20230118084343.26913-1-chunfeng.yun@mediatek.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>

Add SM8550 specific register layout and table configs.

Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230117224148.1914627-7-abel.vesa@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

The new SM8550 SoC bumps up the HW version of QMP phy to v6 for USB,
UFS and PCIE g3x2. Add the new PCS UFS specific offsets in a dedicated
header file.

Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230117224148.1914627-6-abel.vesa@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

The new SM8550 SoC bumps up the HW version of QMP phy to v6 for USB,
UFS and PCIE g3x2. Add the new qserdes TX RX but UFS specific offsets
in a dedicated header file.

Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230117224148.1914627-5-abel.vesa@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

The new SM8550 SoC bumps up the HW version of QMP phy to v6 for USB,
UFS and PCIE g3x2. Add the new qserdes TX RX offsets in a dedicated
header file.

Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230117224148.1914627-4-abel.vesa@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

The new SM8550 SoC bumps up the HW version of QMP phy to v6 for USB,
UFS and PCIE g3x2. Add the new qserdes com offsets in a dedicated
header file.

Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230117224148.1914627-3-abel.vesa@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

Document the QMP UFS PHY compatible for SM8550.

Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230117224148.1914627-2-abel.vesa@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

The NXP TJR1443 High-speed CAN transceiver with Sleep mode is a
pin-compatible alternative for the TI TCAN1043.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/0bfa1e4c43632e49c9512b4e7daa970545545dcf.1674037830.git.geert+renesas@glider.be
Signed-off-by: Vinod Koul <vkoul@kernel.org>

The NXP TJR1443 High-speed CAN transceiver with Sleep mode is a
pin-compatible alternative for the TI TCAN1043.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/6ee5e2ce00019bd3f77d6a702b38bab1a45f3bb0.1674037830.git.geert+renesas@glider.be
Signed-off-by: Vinod Koul <vkoul@kernel.org>

Convert the Tegra XUSB pad controller bindings from free-form text
format to json-schema.

Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20230113150804.1272555-1-thierry.reding@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>

The sdx64 uniphy gen3x1 PHY references the qmp_v4_usb3phy_regs_layout
while the PHY itself uses v5 regs. While there are only minor
differences between v4 and v5 regs and none of them concerns registers
mentions in regs_layout, switch the PHY to use
qmp_v5_usb3phy_regs_layout, to remove possible confusion.

Fixes: 14d98d3b

 ("phy: qcom-qmp-usb: fix regs layout arrays")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230113212138.421583-2-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

The sm8450 gen3x1 PHY references the pciephy_v4_regs_layout while the
PHY itself uses v5 regs. While there are only minor differences between
v4 and v5 regs and none of them concerns registers mentions in
regs_layout, switch the PHY to use pciephy_v5_regs_layout to remove
possible confusion.

Fixes: bbe207a1

 ("phy: qcom-qmp-pcie: rename regs layout arrays")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230113212138.421583-1-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

Use symbolic names for the values inside reg layout arrays. New register
names are added following the PCS register layout that is used by the
particular PHY.

Note: ipq8074 tables appear to use a mixture of v2 and v3 registers.
This might need additional fixes.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230113212102.421491-2-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

The QPHY_PCS_LFPS_RXTERM_IRQ_STATUS register is not used, remove it from
register layout.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230113212102.421491-1-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

All currently known QMP UFS PHYs have the same offsets for register
sub-regions. Instead of using qmp_ufs_offsets_v5 for older generations
of PHYs, rename the offsets struct instance to remove _v5 suffix.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230113195515.407866-1-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

The WIZ acts as a wrapper for SerDes and has Lanes 0 and 2 reserved
for USB for type-C lane swap if Lane 1 and Lane 3 are linked to the
USB PHY that is integrated into the SerDes IP. The WIZ control register
has to be configured to support this lane swap feature.

The support for swapping lanes 2 and 3 is missing and therefore
add support to configure the control register to swap between
lanes 2 and 3 if PHY type is USB.

Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20230113150615.19375-3-sinthu.raja@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>

It's possible that the Type-C plug orientation on the DIR line will be
implemented through hardware design. In that situation, there won't be
an external GPIO line available, but the driver still needs to address
this since the DT won't use the typec-dir-gpios property.

Add code to handle LN10 Type-C swap if typec-dir-gpios property is not
specified in DT.

Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Link: https://lore.kernel.org/r/20230113150615.19375-2-sinthu.raja@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>

UFS PHY in SC8280XP SoC is capable of operating at HS G4 mode and the init
sequence is compatible with SM8350. Hence, add the tbls_hs_g4 instance
reusing the G4 init sequence of SM8350.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # Qdrive3/sa8540p-ride
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20230114071009.88102-13-manivannan.sadhasivam@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

UFS PHY in SM8450 SoC is capable of operating at HS G4 mode and the init
sequence is compatible with SM8350. Hence, add the tbls_hs_g4 instance
reusing the G4 init sequence of SM8350.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # Qdrive3/sa8540p-ride
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20230114071009.88102-12-manivannan.sadhasivam@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

UFS PHY in SM8350 SoC is capable of operating at HS G4 mode. Hence, add the
required register settings using the tables_hs_g4 struct instance.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # Qdrive3/sa8540p-ride
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20230114071009.88102-11-manivannan.sadhasivam@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

SM8350 default init sequence sets some PCS registers to HS G3, thereby
disabling HS G4 mode. This has the effect on MPHY capability negotiation
between the host and the device during link startup and causes the
PA_MAXHSGEAR to G3 irrespective of device max gear.

Due to that, the agreed gear speed determined by the UFS core will become
G3 only and the platform won't run at G4.

So, let's remove setting these registers for SM8350 as like other G4
compatible platforms. One downside of this is that, when the board design
uses non-G4 compatible device, then MPHY will continue to run in the
default mode (G4) even if UFSHCD runs in G3. But this is the case for
other platforms as well.

Tested-by: Andrew Halaney <ahalaney@redhat.com> # Qdrive3/sa8540p-ride
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20230114071009.88102-10-manivannan.sadhasivam@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

UFS PHY in SM8250 SoC is capable of operating at HS G4 mode. Hence, add the
required register settings using the tables_hs_g4 struct instance. This
also requires a separate qmp_phy_cfg for SM8250 instead of reusing SM8150.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # Qdrive3/sa8540p-ride
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20230114071009.88102-9-manivannan.sadhasivam@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

UFS PHY in SM8150 SoC is capable of operating at HS G4 mode. Hence, add the
required register settings using the tables_hs_g4 struct instance.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # Qdrive3/sa8540p-ride
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20230114071009.88102-8-manivannan.sadhasivam@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

Since now there is support for configuring the HS Rate B mode properly,
let's move the register setting to tbls_hs_b struct for all SoCs.

This allows the PHY to be configured in Rate A initially and then in
Rate B if requested by the UFS driver.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # Qdrive3/sa8540p-ride
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20230114071009.88102-7-manivannan.sadhasivam@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

Add separate tables_hs_g4 instance to allow the PHY driver to configure the
PHY in HS G4 mode. The individual SoC configs need to supply the Rx, Tx and
PCS register setting in tables_hs_g4 and the UFS driver can request the
Hs G4 mode by calling phy_set_mode_ext() with submode set to UFS_HS_G4.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # Qdrive3/sa8540p-ride
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20230114071009.88102-6-manivannan.sadhasivam@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

Add separate tables_hs_b instance to allow the PHY driver to configure the
PHY in HS Series B mode. The individual SoC configs need to supply the
serdes register setting in tables_hs_b and the UFS driver can request the
Series B mode by calling phy_set_mode() with mode set to PHY_MODE_UFS_HS_B.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # Qdrive3/sa8540p-ride
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20230114071009.88102-5-manivannan.sadhasivam@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

As done for Qcom PCIe PHY driver, let's move the register settings to the
common qmp_phy_cfg_tbls struct. This helps in adding any additional PHY
settings needed for functionalities like HS-G4 in the future by adding one
more instance of the qmp_phy_cfg_tbls.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # Qdrive3/sa8540p-ride
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20230114071009.88102-4-manivannan.sadhasivam@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

Only MSM8996 is using "_ufs_" naming convention for PHY definitions instead
of "_ufsphy_" as like other SoCs. So to maintain the uniformity, let's
rename all of the definitions to use "_ufsphy_".

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # Qdrive3/sa8540p-ride
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20230114071009.88102-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

Following the other QMP PHY drivers like PCIe, let's remove the "_tbl"
suffix from the qmp_phy_init_tbl definitions. This helps in maintaining
the uniformity across all of the QMP PHY drivers.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # Qdrive3/sa8540p-ride
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20230114071009.88102-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

Convert the Amlogic Meson GXL USB2 PHY bindings to dt-schema.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20221117-b4-amlogic-bindings-convert-v2-8-36ad050bb625@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

The SM6125 UFS PHY is compatible with the one from SM6115. Add a
compatible for it and modify the config from SM6115 to make them
compatible with the SC8280XP binding

Signed-off-by: Lux Aliaga <they@mint.lgbt>
Reviewed-by: Martin Botka <martin.botka@somainline.org>
Link: https://lore.kernel.org/r/20230108195336.388349-4-they@mint.lgbt
Signed-off-by: Vinod Koul <vkoul@kernel.org>

Document the QMP UFS PHY compatible for SM6125.

Signed-off-by: Lux Aliaga <they@mint.lgbt>
Reviewed-by: Martin Botka <martin.botka@somainline.org>
Acked-by: Dhruva Gole <d-gole@ti.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230108195336.388349-3-they@mint.lgbt
Signed-off-by: Vinod Koul <vkoul@kernel.org>

Different variants of Qualcomm USB3 DP PHY take different clocks
(according to upstream DTS and Linux driver):

  sc7280-herobrine-crd.dtb: phy-wrapper@88e9000: clocks: [[43, 151], [39, 0], [43, 153]] is too short
  sc7280-herobrine-crd.dtb: phy-wrapper@88e9000: clock-names:1: 'cfg_ahb' was expected
  ...
  sm8250-hdk.dtb: phy@88e9000: clocks: [[46, 185], [44, 0], [46, 187]] is too short
  sm8250-hdk.dtb: phy@88e9000: clock-names:1: 'cfg_ahb' was expected

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20221225115944.55425-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

USB3 DP PHY on SC7280 is used with SM8250 fallback:

  sc7280-herobrine-evoker.dtb: phy-wrapper@88e9000: compatible: ['qcom,sc7280-qmp-usb3-dp-phy', 'qcom,sm8250-qmp-usb3-dp-phy'] is too long

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20221225115944.55425-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

It is more readable to define properties in top-level "properties:" and
restrict them (if needed) per compatible in the "if" block.  Defining
properties in "if" block  does not work correctly with
additionalProperties:false:

  sc7180-trogdor-pazquel-lte-ti.dtb: phy@88e3000: 'qcom,bias-ctrl-value', 'qcom,charge-ctrl-value', 'qcom,hsdisc-trim-value',
    'qcom,imp-res-offset-value', 'qcom,preemphasis-level', 'qcom,preemphasis-width' do not match any of the regexes: 'pinctrl-[0-9]+'

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20221224154226.43417-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

Document SoC-specific compatibles with generic fallback (e.g.
qcom,usb-snps-hs-7nm-phy) already used in DTSI.  Add SoC-specific
compatibles for PHY on SDX55 and SDX65.

This disallows usage of the qcom,usb-snps-hs-5nm-phy and
qcom,usb-snps-hs-7nm-phy generic compatibles alone.  Do not touch
remaining two compatibles - qcom,usb-snps-femto-v2-phy and
qcom,sc8180x-usb-hs-phy - because there are no upstream users, so not
sure what was the intention for them.

This fixes warnings like:

  sa8295p-adp.dtb: phy@88e5000: compatible: 'oneOf' conditional failed, one must be fixed:
    ['qcom,sc8280xp-usb-hs-phy', 'qcom,usb-snps-hs-5nm-phy'] is too long
    'qcom,sc8280xp-usb-hs-phy' is not one of ['qcom,sm8150-usb-hs-phy', 'qcom,sm8250-usb-hs-phy', 'qcom,sm8350-usb-hs-phy', 'qcom,sm8450-usb-hs-phy']
    'qcom,usb-snps-hs-7nm-phy' was expected

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20221223161835.112079-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>

Remove retry code in r8a779f0_eth_serdes_init() because
r8a779f0_eth_serdes_chan_setting() was fixed so that no timeout
happened in the initializing procedure.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20221226065316.3895480-3-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>

Add r8a779f0_eth_serdes_power_on() to initialize the hardware for
each channel from the step 9 or later on the datasheet. In other words,
the procedure from the step 1 to 8 is for all channel and it is needed
once only. So, the .init() in any channel instance is called, this
driver initializes the hardware from step 1 to 8. And then, .power_on()
is called, this driver initializes the hardware from step 9 or later.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20221226065316.3895480-2-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>