Ported pcie-brcmstb bounce buffer implementation to ARM64.
This enables full 4G RAM usage on Raspberry Pi in 64-bit mode.

Signed-off-by: Yaroslav Rosomakho <yaroslavros@gmail.com>

The hardware will do a 4-byte write to memory on any IN packet received
that is between 1 and 3 bytes long. This tramples memory in the uvcvideo
driver, as it uses a sequence of 1- and 2-byte control transfers to
query the min/max/range/step of each individual camera control and
gives us buffers that are offsets into a struct.

Catch small control transfers in the data phase and use the align_buf
to bounce the correct number of bytes into the URB's buffer.

In general, short packets on non-control endpoints should be OK as URBs
should have enough buffer space for a wMaxPacket size transfer.

See: https://github.com/raspberrypi/linux/issues/3148



Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>

Users have reported log spam created by "Event Ring Full" xHC event
TRBs. These are caused by interrupt latency in conjunction with a very
busy set of devices on the bus. The errors are benign, but throughput
will suffer as the xHC will pause processing of transfers until the
event ring is drained by the kernel. Expand the number of event TRB slots
available by increasing the number of event ring segments in the ERST.

Controllers have a hardware-defined limit as to the number of ERST
entries they can process, so make the actual number in use
min(ERST_MAX_SEGS, hw_max).

Signed-off-by: Jonathan Bell <jonathan@raspberrypi.org>

The I2C interface nodes need aliases to give them fixed bus numbers,
and setting the pulls on the GPIOs (particularly 9-13) increases the
chances of the bus working with weak or absent external pulls.

See: https://www.raspberrypi.org/forums/posting.php?mode=reply&f=107&t=248439



Signed-off-by: Phil Elwell <phil@raspberrypi.org>

See: https://github.com/raspberrypi/linux/issues/3141



Signed-off-by: Phil Elwell <phil@raspberrypi.org>

Update bcm2709_defconfig to match the output from savedefconfig.

Signed-off-by: Phil Elwell <phil@raspberrypi.org>

vc4_plane_atomic_async_update() calls vc4_plane_atomic_check()
which in turn calls vc4_plane_setup_clipping_and_scaling(), and since
commit 58a6a36f ("drm/vc4: Use
drm_atomic_helper_check_plane_state() to simplify the logic"), this
function accesses plane_state->state which will be NULL when called
from the async update path because we're passing the current plane
state, and plane_state->state has been assigned to NULL in
drm_atomic_helper_swap_state().

Pass the new state instead of the current one (the new state has
->state set to a non-NULL value).

Fixes: 58a6a36f

 ("drm/vc4: Use drm_atomic_helper_check_plane_state() to simplify the logic")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20181115105852.9844-1-boris.brezillon@bootlin.com

X/Y positioning of T-format buffers is quite tricky and the current
implementation was failing to position a plane using this format
correctly when the CRTC X, Y or both X and Y offsets were negative.
It was also failing when the SRC X/Y offsets were != 0.

Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20180803092231.26446-5-boris.brezillon@bootlin.com

The offset adjustment depends on the framebuffer modified, so let's
just move this operation in the DRM_FORMAT_MOD_LINEAR case inside
vc4_plane_mode_set().

This we'll be able to fix offset calculation for
DRM_FORMAT_MOD_BROADCOM_VC4_T_TILED and DRM_FORMAT_MOD_BROADCOM_SANDXXX.

Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20180803092231.26446-4-boris.brezillon@bootlin.com

drm_atomic_helper_check_plane_state() takes care of checking the
scaling capabilities and calculating the clipped X/Y offsets for us.

Rely on this function instead of open-coding the logic.

Incidentally, it seems to fix a problem we had with negative X/Y
positioning of YUV planes.

Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20180803092231.26446-3-boris.brezillon@bootlin.com

This is needed to support X/Y negative placement of planes using
T-format buffers.

Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180803092231.26446-2-boris.brezillon@bootlin.com

Y_OFFSET field starts at bit 8 not 7.

Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180803092231.26446-1-boris.brezillon@bootlin.com

commit 8d8bef50 upstream.

Commit 6935224d ("spi: bcm2835: enable support of 3-wire mode")
added 3-wire support to the BCM2835 SPI driver by setting the REN bit
(Read Enable) in the CS register when receiving data.  The REN bit puts
the transmitter in high-impedance state.  The driver recognizes that
data is to be received by checking whether the rx_buf of a transfer is
non-NULL.

Commit 3ecd37ed ("spi: bcm2835: enable dma modes for transfers
meeting certain conditions") subsequently broke 3-wire support because
it set the SPI_MASTER_MUST_RX flag which causes spi_map_msg() to replace
rx_buf with a dummy buffer if it is NULL.  As a result, rx_buf is
*always* non-NULL if DMA is enabled.

Reinstate 3-wire support by not only checking whether rx_buf is non-NULL,
but also checking that it is not the dummy buffer.

Fixes: 3ecd37ed

 ("spi: bcm2835: enable dma modes for transfers meeting certain conditions")
Reported-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v4.2+
Cc: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/328318841455e505370ef8ecad97b646c033dc8a.1562148527.git.lukas@wunner.de


Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit c596687a upstream.

While adding handling for dying task group leaders c03cd773


("cgroup: Include dying leaders with live threads in PROCS
iterations") added an inverted cset skip condition to
css_task_iter_advance_css_set().  It should skip cset if it's
completely empty but was incorrectly testing for the inverse condition
for the dying_tasks list.  Fix it.

Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes: c03cd773

 ("cgroup: Include dying leaders with live threads in PROCS iterations")
Reported-by:  <syzbot+d4bba5ccd4f9a2a68681@syzkaller.appspotmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit cee0c33c upstream.

b636fd38

 ("cgroup: Implement css_task_iter_skip()") introduced
css_task_iter_skip() which is used to fix task iterations skipping
dying threadgroup leaders with live threads.  Skipping is implemented
as a subportion of full advancing but css_task_iter_next() forgot to
fully advance a skipped iterator before determining the next task to
visit causing it to return invalid task pointers.

Fix it by making css_task_iter_next() fully advance the iterator if it
has been skipped since the previous iteration.

Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: syzbot
Link: http://lkml.kernel.org/r/00000000000097025d058a7fd785@google.com
Fixes: b636fd38

 ("cgroup: Implement css_task_iter_skip()")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit c03cd773

 upstream.

CSS_TASK_ITER_PROCS currently iterates live group leaders; however,
this means that a process with dying leader and live threads will be
skipped.  IOW, cgroup.procs might be empty while cgroup.threads isn't,
which is confusing to say the least.

Fix it by making cset track dying tasks and include dying leaders with
live threads in PROCS iteration.

Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-and-tested-by: Topi Miettinen <toiwoton@gmail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b636fd38

 upstream.

When a task is moved out of a cset, task iterators pointing to the
task are advanced using the normal css_task_iter_advance() call.  This
is fine but we'll be tracking dying tasks on csets and thus moving
tasks from cset->tasks to (to be added) cset->dying_tasks.  When we
remove a task from cset->tasks, if we advance the iterators, they may
move over to the next cset before we had the chance to add the task
back on the dying list, which can allow the task to escape iteration.

This patch separates out skipping from advancing.  Skipping only moves
the affected iterators to the next pointer rather than fully advancing
it and the following advancing will recognize that the cursor has
already been moved forward and do the rest of advancing.  This ensures
that when a task moves from one list to another in its cset, as long
as it moves in the right direction, it's always visible to iteration.

This doesn't cause any visible behavior changes.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 6b115bf5

 upstream.

cgroup_release() calls cgroup_subsys->release() which is used by the
pids controller to uncharge its pid.  We want to use it to manage
iteration of dying tasks which requires putting it before
__unhash_process().  Move cgroup_release() above __exit_signal().
While this makes it uncharge before the pid is freed, pid is RCU freed
anyway and the window is very narrow.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 055d8824 ]

Support for handling the PPPOEIOCSFWD ioctl in compat mode was added in
linux-2.5.69 along with hundreds of other commands, but was always broken
sincen only the structure is compatible, but the command number is not,
due to the size being sizeof(size_t), or at first sizeof(sizeof((struct
sockaddr_pppox)), which is different on 64-bit architectures.

Guillaume Nault adds:

  And the implementation was broken until 2016 (see 29e73269

 ("pppoe:
  fix reference counting in PPPoE proxy")), and nobody ever noticed. I
  should probably have removed this ioctl entirely instead of fixing it.
  Clearly, it has never been used.

Fix it by adding a compat_ioctl handler for all pppoe variants that
translates the command number and then calls the regular ioctl function.

All other ioctl commands handled by pppoe are compatible between 32-bit
and 64-bit, and require compat_ptr() conversion.

This should apply to all stable kernels.

Acked-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 003bd5b4 ]

It was reported that after resuming from suspend network fails with
error "do_IRQ: 3.38 No irq handler for vector", see [0]. Enabling WoL
can work around the issue, but the only actual fix is to disable MSI.
So let's mimic the behavior of the vendor driver and disable MSI on
all chip versions before RTL8168d.

[0] https://bugzilla.kernel.org/show_bug.cgi?id=204079

Fixes: 6c6aa15f

 ("r8169: improve interrupt handling")
Reported-by: Dušan Dragić <dragic.dusan@gmail.com>
Tested-by: Dušan Dragić <dragic.dusan@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 90bb7692 ]

This patch prevents a race between user invoked cached counters
query and a neighbor last usage updater.

The cached flow counter stats can be queried by calling
"mlx5_fc_query_cached" which provides the number of bytes and
packets that passed via this flow since the last time this counter
was queried.
It does so by reducting the last saved stats from the current, cached
stats and then updating the last saved stats with the cached stats.
It also provide the lastuse value for that flow.

Since "mlx5e_tc_update_neigh_used_value" needs to retrieve the
last usage time of encapsulation flows, it calls the flow counter
query method periodically and async to user queries of the flow counter
using cls_flower.
This call is causing the driver to update the last reported bytes and
packets from the cache and therefore, future user queries of the flow
stats will return lower than expected number for bytes and packets
since the last saved stats in the driver was updated async to the last
saved stats in cls_flower.

This causes wrong stats presentation of encapsulation flows to user.

Since the neighbor usage updater only needs the lastuse stats from the
cached counter, the fix is to use a dedicated lastuse query call that
returns the lastuse value without synching between the cached stats and
the last saved stats.

Fixes: f6dfb4c3

 ("net/mlx5e: Update neighbour 'used' state using HW flow rules counters")
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 7a32f296 ]

Fix modify_cq_in alignment to match the device specification.
After this fix the 'cq_umem_valid' field will be in the right offset.

Cc: <stable@vger.kernel.org> # 4.19
Fixes: bd371975

 ("net/mlx5: Update mlx5_ifc with DEVX UID bits")
Signed-off-by: Edward Srouji <edwards@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 4b663366 ]

- v1 -> v2: Move skb_set_owner_w to __tun_build_skb to reduce patch size

Small packets going out of a tap device go through an optimized code
path that uses build_skb() rather than sock_alloc_send_pskb(). The
latter calls skb_set_owner_w(), but the small packet code path does not.

The net effect is that small packets are not owned by the userland
application's socket (e.g. QEMU), while large packets are.
This can be seen with a TCP session, where packets are not owned when
the window size is small enough (around PAGE_SIZE), while they are once
the window grows (note that this requires the host to support virtio
tso for the guest to offload segmentation).
All this leads to inconsistent behaviour in the kernel, especially on
netfilter modules that uses sk->socket (e.g. xt_owner).

Fixes: 66ccbc9c

 ("tap: use build_skb() for small packet")
Signed-off-by: Alexis Bauvin <abauvin@scaleway.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 4da5f001 ]

Commit 2753ca5d ("tipc: fix uninit-value in tipc_nl_compat_doit")
broke older tipc tools that use compat interface (e.g. tipc-config from
tipcutils package):

% tipc-config -p
operation not supported

The commit started to reject TIPC netlink compat messages that do not
have attributes. It is too restrictive because some of such messages are
valid (they don't need any arguments):

% grep 'tx none' include/uapi/linux/tipc_config.h
#define  TIPC_CMD_NOOP              0x0000    /* tx none, rx none */
#define  TIPC_CMD_GET_MEDIA_NAMES   0x0002    /* tx none, rx media_name(s) */
#define  TIPC_CMD_GET_BEARER_NAMES  0x0003    /* tx none, rx bearer_name(s) */
#define  TIPC_CMD_SHOW_PORTS        0x0006    /* tx none, rx ultra_string */
#define  TIPC_CMD_GET_REMOTE_MNG    0x4003    /* tx none, rx unsigned */
#define  TIPC_CMD_GET_MAX_PORTS     0x4004    /* tx none, rx unsigned */
#define  TIPC_CMD_GET_NETID         0x400B    /* tx none, rx unsigned */
#define  TIPC_CMD_NOT_NET_ADMIN     0xC001    /* tx none, rx none */

This patch relaxes the original fix and rejects messages without
arguments only if such arguments are expected by a command (reg_type is
non zero).

Fixes: 2753ca5d

 ("tipc: fix uninit-value in tipc_nl_compat_doit")
Cc: stable@vger.kernel.org
Signed-off-by: Taras Kondratiuk <takondra@cisco.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit c5d13969 ]

Make sure the delayed work for stats update is not pending before
wq destruction.
This fixes the module unload path.
The issue is there since day 1.

Fixes: a556c76a

 ("net: mscc: Add initial Ocelot switch support")

Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit c3953a3c ]

Fix two reset-gpio sanity checks which were never converted to use
gpio_is_valid(), and make sure to use -EINVAL to indicate a missing
reset line also for the UART-driver module parameter and for the USB
driver.

This specifically prevents the UART and USB drivers from incidentally
trying to request and use gpio 0, and also avoids triggering a WARN() in
gpio_to_desc() during probe when no valid reset line has been specified.

Fixes: e33a3f84

 ("NFC: nfcmrvl: allow gpio 0 for reset signalling")
Reported-by:  <syzbot+cf35b76f35e068a1107f@syzkaller.appspotmail.com>
Tested-by:  <syzbot+cf35b76f35e068a1107f@syzkaller.appspotmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit f9cedf1a

 ]

The setsockopts options TCP_NODELAY and TCP_CORK may schedule the
tx worker. Make sure the socket is not yet moved into SMC_CLOSED
state (for instance by a shutdown SHUT_RDWR call).

Reported-by:  <syzbot+92209502e7aab127c75f@syzkaller.appspotmail.com>
Reported-by:  <syzbot+b972214bb803a343f4fe@syzkaller.appspotmail.com>
Fixes: 01d2f7e2

 ("net/smc: sockopts TCP_NODELAY and TCP_CORK")
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 7be8ef2c ]

Currently init call of all actions (except ipt) init their 'parm'
structure as a direct pointer to nla data in skb. This leads to race
condition when some of the filter actions were initialized successfully
(and were assigned with idr action index that was written directly
into nla data), but then were deleted and retried (due to following
action module missing or classifier-initiated retry), in which case
action init code tries to insert action to idr with index that was
assigned on previous iteration. During retry the index can be reused
by another action that was inserted concurrently, which causes
unintended action sharing between filters.
To fix described race condition, save action idr index to temporary
stack-allocated variable instead on nla data.

Fixes: 0190c1d4

 ("net: sched: atomically check-allocate action")
Signed-off-by: Dmytro Linkin <dmitrolin@mellanox.com>
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit b35475c5 ]

Add get_fill_size() routine used to calculate the action size
when building a batch of events.

Fixes: c7e2b968

 ("sched: introduce vlan action")
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 051c7b39 ]

In dequeue_func(), there is an if statement on line 74 to check whether
skb is NULL:
    if (skb)

When skb is NULL, it is used on line 77:
    prefetch(&skb->end);

Thus, a possible null-pointer dereference may occur.

To fix this bug, skb->end is used when skb is not NULL.

This bug is found by a static analysis tool STCheck written by us.

Fixes: 76e3cc12

 ("codel: Controlled Delay AQM")
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit a7cf3d24 ]

The udp_ip4_ind bit is set only for IPv4 UDP non-fragmented packets
so that the hardware can flip the checksum to 0xFFFF if the computed
checksum is 0 per RFC768.

However, this bit had to be set for IPv6 UDP non fragmented packets
as well per hardware requirements. Otherwise, IPv6 UDP packets
with computed checksum as 0 were transmitted by hardware and were
dropped in the network.

In addition to setting this bit for IPv6 UDP, the field is also
appropriately renamed to udp_ind as part of this change.

Fixes: 5eb5f860

 ("net: qualcomm: rmnet: Add support for TX checksum offload")
Cc: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 8aace4f3 ]

In phylink_parse_fixedlink() the pl->link_config.advertising bits are AND
with pl->supported, pl->supported is zeroed and only the speed/duplex
modes and MII bits are set.
So pl->link_config.advertising always loses the flow control/pause bits.

By setting Pause and Asym_Pause bits in pl->supported, the flow control
work again when devicetree "pause" is set in fixes-link node and the MAC
advertise that is supports pause.

Results with this patch.

Legend:
- DT = 'Pause' is set in the fixed-link in devicetree.
- validate() = ‘Yes’ means phylink_set(mask, Pause) is set in the
  validate().
- flow = results reported my link is Up line.

+-----+------------+-------+
| DT  | validate() | flow  |
+-----+------------+-------+
| Yes | Yes        | rx/tx |
| No  | Yes        | off   |
| Yes | No         | off   |
+-----+------------+-------+

Fixes: 9525ae83

 ("phylink: add phylink infrastructure")
Signed-off-by: René van Dorst <opensource@vdorst.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 08aa5e7d ]

When lag is active, which is controlled by the bonded mlx5e netdev, mlx5
interface unregestering must happen in the reverse order where rdma is
unregistered (unloaded) first, to guarantee all references to the lag
context in hardware is removed, then remove mlx5e netdev interface which
will cleanup the lag context from hardware.

Without this fix during destroy of LAG interface, we observed following
errors:
 * mlx5_cmd_check:752:(pid 12556): DESTROY_LAG(0x843) op_mod(0x0) failed,
   status bad parameter(0x3), syndrome (0xe4ac33)
 * mlx5_cmd_check:752:(pid 12556): DESTROY_LAG(0x843) op_mod(0x0) failed,
   status bad parameter(0x3), syndrome (0xa5aee8).

Fixes: a31208b1

 ("net/mlx5_core: New init and exit flow for mlx5_core")
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Mark Zhang <markz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 60d60c8f ]

The commit 069d1146 ("net/mlx5e: RX, Enhance legacy Receive Queue
memory scheme") introduced an undefined behaviour below due to
"frag->last_in_page" is only initialized in mlx5e_init_frags_partition()
when,

if (next_frag.offset + frag_info[f].frag_stride > PAGE_SIZE)

or after bailed out the loop,

for (i = 0; i < mlx5_wq_cyc_get_size(&rq->wqe.wq); i++)

As the result, there could be some "frag" have uninitialized
value of "last_in_page".

Later, get_frag() obtains those "frag" and check "frag->last_in_page" in
mlx5e_put_rx_frag() and triggers the error during boot. Fix it by always
initializing "frag->last_in_page" to "false" in
mlx5e_init_frags_partition().

UBSAN: Undefined behaviour in
drivers/net/ethernet/mellanox/mlx5/core/en_rx.c:325:12
load of value 170 is not a valid value for type 'bool' (aka '_Bool')
Call trace:
 dump_backtrace+0x0/0x264
 show_stack+0x20/0x2c
 dump_stack+0xb0/0x104
 __ubsan_handle_load_invalid_value+0x104/0x128
 mlx5e_handle_rx_cqe+0x8e8/0x12cc [mlx5_core]
 mlx5e_poll_rx_cq+0xca8/0x1a94 [mlx5_core]
 mlx5e_napi_poll+0x17c/0xa30 [mlx5_core]
 net_rx_action+0x248/0x940
 __do_softirq+0x350/0x7b8
 irq_exit+0x200/0x26c
 __handle_domain_irq+0xc8/0x128
 gic_handle_irq+0x138/0x228
 el1_irq+0xb8/0x140
 arch_cpu_idle+0x1a4/0x348
 do_idle+0x114/0x1b0
 cpu_startup_entry+0x24/0x28
 rest_init+0x1ac/0x1dc
 arch_call_rest_init+0x10/0x18
 start_kernel+0x4d4/0x57c

Fixes: 069d1146

 ("net/mlx5e: RX, Enhance legacy Receive Queue memory scheme")
Signed-off-by: Qian Cai <cai@lca.pw>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 55b40dbf ]

Commit aca51397 ("netns: Fix arbitrary net_device-s corruptions
on net_ns stop.") introduced a possibility to hit a BUG in case device
is returning back to init_net and two following conditions are met:
1) dev->ifindex value is used in a name of another "dev%d"
   device in init_net.
2) dev->name is used by another device in init_net.

Under real life circumstances this is hard to get. Therefore this has
been present happily for over 10 years. To reproduce:

$ ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host
       valid_lft forever preferred_lft forever
2: dummy0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN group default qlen 1000
    link/ether 86:89:3f:86:61:29 brd ff:ff:ff:ff:ff:ff
3: enp0s2: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
    link/ether 52:54:00:12:34:56 brd ff:ff:ff:ff:ff:ff
$ ip netns add ns1
$ ip -n ns1 link add dummy1ns1 type dummy
$ ip -n ns1 link add dummy2ns1 type dummy
$ ip link set enp0s2 netns ns1
$ ip -n ns1 link set enp0s2 name dummy0
[  100.858894] virtio_net virtio0 dummy0: renamed from enp0s2
$ ip link add dev4 type dummy
$ ip -n ns1 a
1: lo: <LOOPBACK> mtu 65536 qdisc noop state DOWN group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: dummy1ns1: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN group default qlen 1000
    link/ether 16:63:4c:38:3e:ff brd ff:ff:ff:ff:ff:ff
3: dummy2ns1: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN group default qlen 1000
    link/ether aa:9e:86:dd:6b:5d brd ff:ff:ff:ff:ff:ff
4: dummy0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
    link/ether 52:54:00:12:34:56 brd ff:ff:ff:ff:ff:ff
$ ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host
       valid_lft forever preferred_lft forever
2: dummy0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN group default qlen 1000
    link/ether 86:89:3f:86:61:29 brd ff:ff:ff:ff:ff:ff
4: dev4: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN group default qlen 1000
    link/ether 5a:e1:4a:b6:ec:f8 brd ff:ff:ff:ff:ff:ff
$ ip netns del ns1
[  158.717795] default_device_exit: failed to move dummy0 to init_net: -17
[  158.719316] ------------[ cut here ]------------
[  158.720591] kernel BUG at net/core/dev.c:9824!
[  158.722260] invalid opcode: 0000 [#1] SMP KASAN PTI
[  158.723728] CPU: 0 PID: 56 Comm: kworker/u2:1 Not tainted 5.3.0-rc1+ #18
[  158.725422] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-2.fc30 04/01/2014
[  158.727508] Workqueue: netns cleanup_net
[  158.728915] RIP: 0010:default_device_exit.cold+0x1d/0x1f
[  158.730683] Code: 84 e8 18 c9 3e fe 0f 0b e9 70 90 ff ff e8 36 e4 52 fe 89 d9 4c 89 e2 48 c7 c6 80 d6 25 84 48 c7 c7 20 c0 25 84 e8 f4 c8 3e
[  158.736854] RSP: 0018:ffff8880347e7b90 EFLAGS: 00010282
[  158.738752] RAX: 000000000000003b RBX: 00000000ffffffef RCX: 0000000000000000
[  158.741369] RDX: 0000000000000000 RSI: ffffffff8128013d RDI: ffffed10068fcf64
[  158.743418] RBP: ffff888033550170 R08: 000000000000003b R09: fffffbfff0b94b9c
[  158.745626] R10: fffffbfff0b94b9b R11: ffffffff85ca5cdf R12: ffff888032f28000
[  158.748405] R13: dffffc0000000000 R14: ffff8880335501b8 R15: 1ffff110068fcf72
[  158.750638] FS:  0000000000000000(0000) GS:ffff888036000000(0000) knlGS:0000000000000000
[  158.752944] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  158.755245] CR2: 00007fe8b45d21d0 CR3: 00000000340b4005 CR4: 0000000000360ef0
[  158.757654] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[  158.760012] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[  158.762758] Call Trace:
[  158.763882]  ? dev_change_net_namespace+0xbb0/0xbb0
[  158.766148]  ? devlink_nl_cmd_set_doit+0x520/0x520
[  158.768034]  ? dev_change_net_namespace+0xbb0/0xbb0
[  158.769870]  ops_exit_list.isra.0+0xa8/0x150
[  158.771544]  cleanup_net+0x446/0x8f0
[  158.772945]  ? unregister_pernet_operations+0x4a0/0x4a0
[  158.775294]  process_one_work+0xa1a/0x1740
[  158.776896]  ? pwq_dec_nr_in_flight+0x310/0x310
[  158.779143]  ? do_raw_spin_lock+0x11b/0x280
[  158.780848]  worker_thread+0x9e/0x1060
[  158.782500]  ? process_one_work+0x1740/0x1740
[  158.784454]  kthread+0x31b/0x420
[  158.786082]  ? __kthread_create_on_node+0x3f0/0x3f0
[  158.788286]  ret_from_fork+0x3a/0x50
[  158.789871] ---[ end trace defd6c657c71f936 ]---
[  158.792273] RIP: 0010:default_device_exit.cold+0x1d/0x1f
[  158.795478] Code: 84 e8 18 c9 3e fe 0f 0b e9 70 90 ff ff e8 36 e4 52 fe 89 d9 4c 89 e2 48 c7 c6 80 d6 25 84 48 c7 c7 20 c0 25 84 e8 f4 c8 3e
[  158.804854] RSP: 0018:ffff8880347e7b90 EFLAGS: 00010282
[  158.807865] RAX: 000000000000003b RBX: 00000000ffffffef RCX: 0000000000000000
[  158.811794] RDX: 0000000000000000 RSI: ffffffff8128013d RDI: ffffed10068fcf64
[  158.816652] RBP: ffff888033550170 R08: 000000000000003b R09: fffffbfff0b94b9c
[  158.820930] R10: fffffbfff0b94b9b R11: ffffffff85ca5cdf R12: ffff888032f28000
[  158.825113] R13: dffffc0000000000 R14: ffff8880335501b8 R15: 1ffff110068fcf72
[  158.829899] FS:  0000000000000000(0000) GS:ffff888036000000(0000) knlGS:0000000000000000
[  158.834923] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  158.838164] CR2: 00007fe8b45d21d0 CR3: 00000000340b4005 CR4: 0000000000360ef0
[  158.841917] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[  158.845149] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400

Fix this by checking if a device with the same name exists in init_net
and fallback to original code - dev%d to allocate name - in case it does.

This was found using syzkaller.

Fixes: aca51397

 ("netns: Fix arbitrary net_device-s corruptions on net_ns stop.")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 5c725b6b ]

When permanent entries were introduced by the commit below, they were
exempt from timing out and thus igmp leave wouldn't affect them unless
fast leave was enabled on the port which was added before permanent
entries existed. It shouldn't matter if fast leave is enabled or not
if the user added a permanent entry it shouldn't be deleted on igmp
leave.

Before:
$ echo 1 > /sys/class/net/eth4/brport/multicast_fast_leave
$ bridge mdb add dev br0 port eth4 grp 229.1.1.1 permanent
$ bridge mdb show
dev br0 port eth4 grp 229.1.1.1 permanent

< join and leave 229.1.1.1 on eth4 >

$ bridge mdb show
$

After:
$ echo 1 > /sys/class/net/eth4/brport/multicast_fast_leave
$ bridge mdb add dev br0 port eth4 grp 229.1.1.1 permanent
$ bridge mdb show
dev br0 port eth4 grp 229.1.1.1 permanent

< join and leave 229.1.1.1 on eth4 >

$ bridge mdb show
dev br0 port eth4 grp 229.1.1.1 permanent

Fixes: ccb1c31a

 ("bridge: add flags to distinguish permanent mdb entires")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit d7bae09f

 ]

On initialization failure we have to delete the local fdb which was
inserted due to the default pvid creation. This problem has been present
since the inception of default_pvid. Note that currently there are 2 cases:
1) in br_dev_init() when br_multicast_init() fails
2) if register_netdevice() fails after calling ndo_init()

This patch takes care of both since br_vlan_flush() is called on both
occasions. Also the new fdb delete would be a no-op on normal bridge
device destruction since the local fdb would've been already flushed by
br_dev_delete(). This is not an issue for ports since nbp_vlan_init() is
called last when adding a port thus nothing can fail after it.

Reported-by:  <syzbot+88533dc8b582309bf3ee@syzkaller.appspotmail.com>
Fixes: 5be5a2df

 ("bridge: Add filtering support for default_pvid")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>