Signed-off-by: popcornmix <popcornmix@gmail.com>

Signed-off-by: popcornmix <popcornmix@gmail.com>

Commit <eea52743> upstream

Fixes: <b3e3893e

> ("net: use core MTU range checking")
which patched only one of two functions used to setup the
USB Gadget Ethernet driver, causing a serious performance
regression in the ability to increase mtu size above 1500.

Signed-off-by: John Greb <h3x4m3r0n@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>

commit 9dbc8a03 upstream.

Fixes: 8043bb1a

 ("crypto: omap-sham - convert driver logic to use sgs for data xmit")

The memory pages freed in omap_sham_finish_req() were less than those
allocated in omap_sham_copy_sgs().

Cc: stable@vger.kernel.org
Signed-off-by: Bin Liu <b-liu@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 730f23b6 upstream.

In p8_aes_xts_init() we do a printk(KERN_INFO ...) to report the
fallback implementation we're using. However with a slow console this
can significantly affect the speed of crypto operations. So remove it.

Fixes: c07f5d3d

 ("crypto: vmx - Adding support for XTS")
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 1411b521 upstream.

In the vmx AES init routines we do a printk(KERN_INFO ...) to report
the fallback implementation we're using.

However with a slow console this can significantly affect the speed of
crypto operations. Using 'cryptsetup benchmark' the removal of the
printk() leads to a ~5x speedup for aes-cbc decryption.

So remove them.

Fixes: 8676590a ("crypto: vmx - Adding AES routines for VMX module")
Fixes: 8c755ace ("crypto: vmx - Adding CBC routines for VMX module")
Fixes: 4f7f60d3 ("crypto: vmx - Adding CTR routines for VMX module")
Fixes: cc333cd6

 ("crypto: vmx - Adding GHASH routines for VMX module")
Cc: stable@vger.kernel.org # v4.1+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit c782a8c4

 upstream.

After issuing a request an endless loop was used to read the
completion state from memory which is asynchronously updated
by the ZIP coprocessor.

Add an upper bound to the retry attempts to prevent a CPU getting stuck
forever in case of an error. Additionally, add a read memory barrier
and a small delay between the reading attempts.

Signed-off-by: Jan Glauber <jglauber@cavium.com>
Reviewed-by: Robert Richter <rrichter@cavium.com>
Cc: stable <stable@vger.kernel.org> # 4.14
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 37ff02ac

 upstream.

Enabling virtual mapped kernel stacks breaks the thunderx_zip
driver. On compression or decompression the executing CPU hangs
in an endless loop. The reason for this is the usage of __pa
by the driver which does no longer work for an address that is
not part of the 1:1 mapping.

The zip driver allocates a result struct on the stack and needs
to tell the hardware the physical address within this struct
that is used to signal the completion of the request.

As the hardware gets the wrong address after the broken __pa
conversion it writes to an arbitrary address. The zip driver then
waits forever for the completion byte to contain a non-zero value.

Allocating the result struct from 1:1 mapped memory resolves this
bug.

Signed-off-by: Jan Glauber <jglauber@cavium.com>
Reviewed-by: Robert Richter <rrichter@cavium.com>
Cc: stable <stable@vger.kernel.org> # 4.14
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 4bffaab3 upstream.

Fix a typo where size of RSA prime factor q is using the size of
prime factor p.

Cc: <stable@vger.kernel.org> # 4.13+
Fixes: 52e26d77 ("crypto: caam - add support for RSA key form 2")
Fixes: 4a651b12

 ("crypto: caam - add support for RSA key form 3")
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 3a488aae upstream.

There are two IV-related issues:
(1) crypto API does not guarantee to provide an IV buffer that is DMAable,
thus it's incorrect to DMA map it
(2) for in-place decryption, since ciphertext is overwritten with
plaintext, updated IV (req->info) will contain the last block of plaintext
(instead of the last block of ciphertext)

While these two issues could be fixed separately, it's straightforward
to fix both in the same time - by using the {ablkcipher,aead}_edesc
extended descriptor to store the IV that will be fed to the crypto engine;
this allows for fixing (2) by saving req->src[last_block] in req->info
directly, i.e. without allocating yet another temporary buffer.

A side effect of the fix is that it's no longer possible to have the IV
contiguous with req->src or req->dst.
Code checking for this case is removed.

Cc: <stable@vger.kernel.org> # 4.14+
Fixes: a68a1938 ("crypto: caam/qi - properly set IV after {en,de}crypt")
Link: http://lkml.kernel.org/r/20170113084620.GF22022@gondor.apana.org.au


Reported-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 115957bb upstream.

There are two IV-related issues:
(1) crypto API does not guarantee to provide an IV buffer that is DMAable,
thus it's incorrect to DMA map it
(2) for in-place decryption, since ciphertext is overwritten with
plaintext, updated req->info will contain the last block of plaintext
(instead of the last block of ciphertext)

While these two issues could be fixed separately, it's straightforward
to fix both in the same time - by allocating extra space in the
ablkcipher_edesc for the IV that will be fed to the crypto engine;
this allows for fixing (2) by saving req->src[last_block] in req->info
directly, i.e. without allocating another temporary buffer.

A side effect of the fix is that it's no longer possible to have the IV
and req->src contiguous. Code checking for this case is removed.

Cc: <stable@vger.kernel.org> # 4.13+
Fixes: 854b06f7 ("crypto: caam - properly set IV after {en,de}crypt")
Link: http://lkml.kernel.org/r/20170113084620.GF22022@gondor.apana.org.au


Reported-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit a38acd23 upstream.

In case of GIVCIPHER, IV is generated by the device.
Fix the DMA mapping direction.

Cc: <stable@vger.kernel.org> # 3.19+
Fixes: 7222d1a3

 ("crypto: caam - add support for givencrypt cbc(aes) and rfc3686(ctr(aes))")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 8a2a0dd3 upstream.

Sometimes the provided RSA input buffer provided is not stripped
of leading zeros. This could cause its size to be bigger than that
of the modulus, making the HW complain:

caam_jr 2142000.jr1: 40000789: DECO: desc idx 7:
Protocol Size Error - A protocol has seen an error in size. When
running RSA, pdb size N < (size of F) when no formatting is used; or
pdb size N < (F + 11) when formatting is used.

Fix the problem by stripping off the leading zero from input data
before feeding it to the CAAM accelerator.

Fixes: 8c419778

 ("crypto: caam - add support for RSA algorithm")
Cc: <stable@vger.kernel.org> # 4.8+
Reported-by: Martin Townsend <mtownsend1973@gmail.com>
Link: https://lkml.kernel.org/r/CABatt_ytYORYKtApcB4izhNanEKkGFi9XAQMjHi_n-8YWoCRiw@mail.gmail.com


Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit e6e7e9cd upstream.

Add ELAN0612 to the list of supported touchpads; this ID is used in Lenovo
v330 14IKB devices.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=199253


Signed-off-by: Johannes Wienke <languitar@semipol.de>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 5ca4d1ae upstream.

GPD Win 2 Website: http://www.gpd.hk/gpdwin2.asp



Tested on a unit from the first production run sent to Indiegogo backers

Signed-off-by: Ethan Lee <flibitijibibo@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 3c9fa24c upstream.

The functions that were used in the emulation of fxrstor, fxsave, sgdt and
sidt were originally meant for task switching, and as such they did not
check privilege levels.  This is very bad when the same functions are used
in the emulation of unprivileged instructions.  This is CVE-2018-10853.

The obvious fix is to add a new argument to ops->read_std and ops->write_std,
which decides whether the access is a "system" access or should use the
processor's CPL.

Fixes: 129a72a0

 ("KVM: x86: Introduce segmented_write_std", 2017-01-12)
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 4a7e625c upstream.

Commit 9b96fbac ("serial: PL011: clear pending interrupts")
clears the RX and receive timeout interrupts on pl011 startup, to
avoid a screaming-interrupt scenario that can occur when the
firmware or bootloader leaves these interrupts asserted.

This has been noted as an issue when running Linux on qemu [1].

Unfortunately, the above fix seems to lead to potential
misbehaviour if the RX FIFO interrupt is asserted _non_ spuriously
on driver startup, if the RX FIFO is also already full to the
trigger level.

Clearing the RX FIFO interrupt does not change the FIFO fill level.
In this scenario, because the interrupt is now clear and because
the FIFO is already full to the trigger level, no new assertion of
the RX FIFO interrupt can occur unless the FIFO is drained back
below the trigger level.  This never occurs because the pl011
driver is waiting for an RX FIFO interrupt to tell it that there is
something to read, and does not read the FIFO at all until that
interrupt occurs.

Thus, simply clearing "spurious" interrupts on startup may be
misguided, since there is no way to be sure that the interrupts are
truly spurious, and things can go wrong if they are not.

This patch instead clears the interrupt condition by draining the
RX FIFO during UART startup, after clearing any potentially
spurious interrupt.  This should ensure that an interrupt will
definitely be asserted if the RX FIFO subsequently becomes
sufficiently full.

The drain is done at the point of enabling interrupts only.  This
means that it will occur any time the UART is newly opened through
the tty layer.  It will not apply to polled-mode use of the UART by
kgdboc: since that scenario cannot use interrupts by design, this
should not matter.  kgdboc will interact badly with "normal" use of
the UART in any case: this patch makes no attempt to paper over
such issues.

This patch does not attempt to address the case where the RX FIFO
fills faster than it can be drained: that is a pathological
hardware design problem that is beyond the scope of the driver to
work around.  As a failsafe, the number of poll iterations for
draining the FIFO is limited to twice the FIFO size.  This will
ensure that the kernel at least boots even if it is impossible to
drain the FIFO for some reason.

[1] [Qemu-devel] [Qemu-arm] [PATCH] pl011: do not put into fifo
before enabled the interruption
https://lists.gnu.org/archive/html/qemu-devel/2018-01/msg06446.html



Reported-by: Wei Xu <xuwei5@hisilicon.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Peter Maydell <peter.maydell@linaro.org>
Fixes: 9b96fbac

 ("serial: PL011: clear pending interrupts")
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Cc: stable <stable@vger.kernel.org>
Tested-by: Wei Xu <xuwei5@hisilicon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b23220fe upstream.

The balloon.page field is used for two different purposes if batching is
on or off. If batching is on, the field point to the page which is used
to communicate with with the hypervisor. If it is off, balloon.page
points to the page that is about to be (un)locked.

Unfortunately, this dual-purpose of the field introduced a bug: when the
balloon is popped (e.g., when the machine is reset or the balloon driver
is explicitly removed), the balloon driver frees, unconditionally, the
page that is held in balloon.page.  As a result, if batching is
disabled, this leads to double freeing the last page that is sent to the
hypervisor.

The following error occurs during rmmod when kernel checkers are on, and
the balloon is not empty:

[   42.307653] ------------[ cut here ]------------
[   42.307657] Kernel BUG at ffffffffba1e4b28 [verbose debug info unavailable]
[   42.307720] invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC
[   42.312512] Modules linked in: vmw_vsock_vmci_transport vsock ppdev joydev vmw_balloon(-) input_leds serio_raw vmw_vmci parport_pc shpchp parport i2c_piix4 nfit mac_hid autofs4 vmwgfx drm_kms_helper hid_generic syscopyarea sysfillrect usbhid sysimgblt fb_sys_fops hid ttm mptspi scsi_transport_spi ahci mptscsih drm psmouse vmxnet3 libahci mptbase pata_acpi
[   42.312766] CPU: 10 PID: 1527 Comm: rmmod Not tainted 4.12.0+ #5
[   42.312803] Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 09/30/2016
[   42.313042] task: ffff9bf9680f8000 task.stack: ffffbfefc1638000
[   42.313290] RIP: 0010:__free_pages+0x38/0x40
[   42.313510] RSP: 0018:ffffbfefc163be98 EFLAGS: 00010246
[   42.313731] RAX: 000000000000003e RBX: ffffffffc02b9720 RCX: 0000000000000006
[   42.313972] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff9bf97e08e0a0
[   42.314201] RBP: ffffbfefc163be98 R08: 0000000000000000 R09: 0000000000000000
[   42.314435] R10: 0000000000000000 R11: 0000000000000000 R12: ffffffffc02b97e4
[   42.314505] R13: ffffffffc02b9748 R14: ffffffffc02b9728 R15: 0000000000000200
[   42.314550] FS:  00007f3af5fec700(0000) GS:ffff9bf97e080000(0000) knlGS:0000000000000000
[   42.314599] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   42.314635] CR2: 00007f44f6f4ab24 CR3: 00000003a7d12000 CR4: 00000000000006e0
[   42.314864] Call Trace:
[   42.315774]  vmballoon_pop+0x102/0x130 [vmw_balloon]
[   42.315816]  vmballoon_exit+0x42/0xd64 [vmw_balloon]
[   42.315853]  SyS_delete_module+0x1e2/0x250
[   42.315891]  entry_SYSCALL_64_fastpath+0x23/0xc2
[   42.315924] RIP: 0033:0x7f3af5b0e8e7
[   42.315949] RSP: 002b:00007fffe6ce0148 EFLAGS: 00000206 ORIG_RAX: 00000000000000b0
[   42.315996] RAX: ffffffffffffffda RBX: 000055be676401e0 RCX: 00007f3af5b0e8e7
[   42.316951] RDX: 000000000000000a RSI: 0000000000000800 RDI: 000055be67640248
[   42.317887] RBP: 0000000000000003 R08: 0000000000000000 R09: 1999999999999999
[   42.318845] R10: 0000000000000883 R11: 0000000000000206 R12: 00007fffe6cdf130
[   42.319755] R13: 0000000000000000 R14: 0000000000000000 R15: 000055be676401e0
[   42.320606] Code: c0 74 1c f0 ff 4f 1c 74 02 5d c3 85 f6 74 07 e8 0f d8 ff ff 5d c3 31 f6 e8 c6 fb ff ff 5d c3 48 c7 c6 c8 0f c5 ba e8 58 be 02 00 <0f> 0b 66 0f 1f 44 00 00 66 66 66 66 90 48 85 ff 75 01 c3 55 48
[   42.323462] RIP: __free_pages+0x38/0x40 RSP: ffffbfefc163be98
[   42.325735] ---[ end trace 872e008e33f81508 ]---

To solve the bug, we eliminate the dual purpose of balloon.page.

Fixes: f220a80f

 ("VMware balloon: add batching to the vmw_balloon.")
Cc: stable@vger.kernel.org
Reported-by: Oleksandr Natalenko <onatalen@redhat.com>
Signed-off-by: Gil Kupfer <gilkup@gmail.com>
Signed-off-by: Nadav Amit <namit@vmware.com>
Reviewed-by: Xavier Deguillard <xdeguillard@vmware.com>
Tested-by: Oleksandr Natalenko <oleksandr@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 13dc04d0 upstream.

I noticed that unused UARTs won't necessarily idle properly always
unless at least one byte tx transfer is done first.

After some debugging I narrowed down the problem to the scr register
dma configuration bits that need to be set before softreset for the
clocks to idle. Unless we do this, the module clkctrl idlest bits
may be set to 1 instead of 3 meaning the clock will never idle and
is blocking deeper idle states for the whole domain.

This might be related to the configuration done by the bootloader
or kexec booting where certain configurations cause the 8250 or
the clkctrl clock to jam in a way where setting of the scr bits
and reset is needed to clear it. I've tried diffing the 8250
registers for the various modes, but did not see anything specific.
So far I've only seen this on omap4 but I'm suspecting this might
also happen on the other clkctrl using SoCs considering they
already have a quirk enabled for UART_ERRATA_CLOCK_DISABLE.

Let's fix the issue by configuring scr before reset for basic dma
even if we don't use it. The scr register will be reset when we do
softreset few lines after, and we restore scr on resume. We should
do this for all the SoCs with UART_ERRATA_CLOCK_DISABLE quirk flag
set since the ones with UART_ERRATA_CLOCK_DISABLE are all based
using clkctrl similar to omap4.

Looks like both OMAP_UART_SCR_DMAMODE_1 | OMAP_UART_SCR_DMAMODE_CTL
bits are needed for the clkctrl to idle after a softreset.

And we need to add omap4 to also use the UART_ERRATA_CLOCK_DISABLE
for the related workaround to be enabled. This same compatible
value will also be used for omap5.

Fixes: cdb929e4

 ("serial: 8250_omap: workaround errata around idling UART after using DMA")
Cc: Keerthy <j-keerthy@ti.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit aa2f80e7 upstream.

The best granularity of residue that DMA engine can report is in the BURST
units, so the serial driver must use MAXBURST = 1 and DMA_SLAVE_BUSWIDTH_1_BYTE
if it relies on exact number of bytes transferred by DMA engine.

Fixes: 62c37eed

 ("serial: samsung: add dma reqest/release functions")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 9594b5be upstream.

I was puzzled while looking at /proc/interrupts and random things showed
up between reboots. This occurred more often but I realised it later. The
"correct" output should be:
|38:      11861  atmel-aic5   2 Level     ttyS0

but I saw sometimes
|38:       6426  atmel-aic5   2 Level     tty1

and accounted it wrongly as correct. This is use after free and the
former example randomly got the "old" pointer which pointed to the same
content. With SLAB_FREELIST_RANDOM and HARDENED I even got
|38:       7067  atmel-aic5   2 Level     E=Started User Manager for UID 0

or other nonsense.
As it turns out the tty, pointer that is accessed in atmel_startup(), is
freed() before atmel_shutdown(). It seems to happen quite often that the
tty for ttyS0 is allocated and freed while ->shutdown is not invoked. I
don't do anything special - just a systemd boot :)

Use dev_name(&pdev->dev) as the IRQ name for request_irq(). This exists
as long as the driver is loaded so no use-after-free here.

Cc: stable@vger.kernel.org
Fixes: 761ed4a9

 ("tty: serial_core: convert uart_close to use tty_port_close")
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d63c16f8 upstream.

Printk format "%pCr" will be removed soon, as clk_get_rate() must not be
called in atomic context.

Replace it by open-coding the operation.  This is safe here, as the code
runs in task context.

Link: http://lkml.kernel.org/r/1527845302-12159-4-git-send-email-geert+renesas@glider.be


To: Jia-Ju Bai <baijiaju1990@gmail.com>
To: Jonathan Corbet <corbet@lwn.net>
To: Michael Turquette <mturquette@baylibre.com>
To: Stephen Boyd <sboyd@kernel.org>
To: Zhang Rui <rui.zhang@intel.com>
To: Eduardo Valentin <edubezval@gmail.com>
To: Eric Anholt <eric@anholt.net>
To: Stefan Wahren <stefan.wahren@i2se.com>
To: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: linux-doc@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: linux-serial@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable@vger.kernel.org # 4.5+
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit bd6bce00 upstream.

This patch fixes an issue that reconnection is possible to fail
because unexpected state handling happens by the irqs. To fix the issue,
the driver disables the controller's irqs when disconnected.

Fixes: 746bfe63

 ("usb: gadget: renesas_usb3: add support for Renesas USB3.0 peripheral controller")
Cc: <stable@vger.kernel.org> # v4.5+
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 4a014a73

 upstream.

When printer_write() calls usb_ep_queue(), a udc driver (e.g.
renesas_usbhs driver) may call usb_gadget_giveback_request() in
the udc .queue ops immediately. Then, printer_write() calls
list_add(&req->list, &dev->tx_reqs_active) wrongly. After that,
if we do unbind the printer driver, WARN_ON() happens in
printer_func_unbind() because the list entry is not removed.

So, this patch moves list_add(&req->list, &dev->tx_reqs_active)
calling before usb_ep_queue().

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 0b4555e7 upstream.

Driver currently crashes due to NULL pointer deference
while updating PHY tune register if nvmem cell is NULL.
Since, fused value for Tune1/2 register is optional,
we'd rather bail out.

Fixes: ca04d9d3

 ("phy: qcom-qusb2: New driver for QUSB2 PHY on Qcom chips")
Reviewed-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Cc: stable <stable@vger.kernel.org> # 4.14+
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit c1ba0839 upstream.

GPD Win 2 Website: http://www.gpd.hk/gpdwin2.asp



Tested on a unit from the first production run sent to Indiegogo backers

Signed-off-by: Ethan Lee <flibitijibibo@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit ca7d9515

 upstream.

The "G-Drive" (sold by G-Technology) external USB 3.0 drive
 hangs on write access under UAS and usb-storage:

[  136.079121] sd 15:0:0:0: [sdi] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[  136.079144] sd 15:0:0:0: [sdi] tag#0 Sense Key : Illegal Request [current]
[  136.079152] sd 15:0:0:0: [sdi] tag#0 Add. Sense: Invalid field in cdb
[  136.079176] sd 15:0:0:0: [sdi] tag#0 CDB: Write(16) 8a 08 00 00 00 00 00 00 00 00 00 00 00 08 00 00
[  136.079180] print_req_error: critical target error, dev sdi, sector 0
[  136.079183] Buffer I/O error on dev sdi, logical block 0, lost sync page write
[  136.173148] EXT4-fs (sdi): mounted filesystem with ordered data mode. Opts: (null)
[  140.583998] sd 15:0:0:0: [sdi] tag#0 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[  140.584010] sd 15:0:0:0: [sdi] tag#0 Sense Key : Illegal Request [current]
[  140.584016] sd 15:0:0:0: [sdi] tag#0 Add. Sense: Invalid field in cdb
[  140.584022] sd 15:0:0:0: [sdi] tag#0 CDB: Write(16) 8a 08 00 00 00 00 e8 c4 00 18 00 00 00 08 00 00
[  140.584025] print_req_error: critical target error, dev sdi, sector 3905159192
[  140.584044] print_req_error: critical target error, dev sdi, sector 3905159192
[  140.584052] Aborting journal on device sdi-8.

The proposed patch adds compatibility quirks. Because the drive requires two
quirks (one to work with UAS, and another to work with usb-storage), adding this
under unusual_devs.h and not just unusual_uas.h so kernels compiled without UAS
receive the quirk. With the patch, the drive works reliably on UAS and usb-
storage.
(tested on NEC Corporation uPD720200 USB 3.0 host controller).

Signed-off-by: Alexander Kappner <agk@godking.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 8c4e97dd

 upstream.

The ALWAYS_SYNC flag is currently honored by the usb-storage driver but not UAS
and is required to work around devices that become unstable upon being
queried for cache. This code is taken straight from:
drivers/usb/storage/scsiglue.c:284

Signed-off-by: Alexander Kappner <agk@godking.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit a0d6ec88 upstream.

pdev_nr and rhport can be controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.

This issue was detected with the help of Smatch:
drivers/usb/usbip/vhci_sysfs.c:238 detach_store() warn: potential spectre issue 'vhcis'
drivers/usb/usbip/vhci_sysfs.c:328 attach_store() warn: potential spectre issue 'vhcis'
drivers/usb/usbip/vhci_sysfs.c:338 attach_store() warn: potential spectre issue 'vhci->vhci_hcd_ss->vdev'
drivers/usb/usbip/vhci_sysfs.c:340 attach_store() warn: potential spectre issue 'vhci->vhci_hcd_hs->vdev'

Fix this by sanitizing pdev_nr and rhport before using them to index
vhcis and vhci->vhci_hcd_ss->vdev respectively.

Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].

[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2



Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit dbafc289

 upstream.

It's amazing that this driver ever worked, but now that x86 doesn't
allow USB data to be sent off of the stack, it really does not work at
all.  Fix this up by properly allocating the data for the small
"commands" that get sent to the device off of the stack.

We do this for one command by having a whole urb just for ack messages,
as they can be submitted in interrupt context, so we can not use
usb_bulk_msg().  But the poweron command can sleep (and does), so use
usb_bulk_msg() for that transfer.

Reported-by: Carlos Manuel Santos <cmmpsantos@gmail.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 45ad559a

 upstream.

Syzbot reported yet another warning with Ion:

WARNING: CPU: 0 PID: 1467 at drivers/staging/android/ion/ion.c:122
ion_buffer_destroy+0xd4/0x190 drivers/staging/android/ion/ion.c:122
Kernel panic - not syncing: panic_on_warn set ...

This is catching that a buffer was freed with an existing kernel mapping
still present. This can be easily be triggered from userspace by calling
DMA_BUF_SYNC_START without calling DMA_BUF_SYNC_END. Switch to a single
pr_warn_once to indicate the error without being disruptive.

Reported-by:  <syzbot+cd8bcd40cb049efa2770@syzkaller.appspotmail.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit ce14e868 upstream.

Int the next patch the emulator's .read_std and .write_std callbacks will
grow another argument, which is not needed in kvm_read_guest_virt and
kvm_write_guest_virt_system's callers.  Since we have to make separate
functions, let's give the currently existing names a nicer interface, too.

Fixes: 129a72a0

 ("KVM: x86: Introduce segmented_write_std", 2017-01-12)
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 727ba748 upstream.

VMX instructions executed inside a L1 VM will always trigger a VM exit
even when executed with cpl 3. This means we must perform the
privilege check in software.

Fixes: 70f3aac9

("kvm: nVMX: Remove superfluous VMX instruction fault checks")
Cc: stable@vger.kernel.org
Signed-off-by: Felix Wilhelm <fwilhelm@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 79367a65 upstream.

Wrap the common invocation of ctxt->ops->read_std and ctxt->ops->write_std, so
as to have a smaller patch when the functions grow another argument.

Fixes: 129a72a0

 ("KVM: x86: Introduce segmented_write_std", 2017-01-12)
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit a780a3ea upstream.

MSB of CR3 is a reserved bit if the PCIDE bit is not set in CR4.
It should be checked when PCIDE bit is not set, however commit
'd1cd3ce9 ("KVM: MMU: check guest CR3 reserved bits based on
its physical address width")' removes the bit 63 checking
unconditionally. This patch fixes it by checking bit 63 of CR3
when PCIDE bit is not set in CR4.

Fixes: d1cd3ce9

 (KVM: MMU: check guest CR3 reserved bits based on its physical address width)
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Liran Alon <liran.alon@oracle.com>
Cc: stable@vger.kernel.org
Reviewed-by: Junaid Shahid <junaids@google.com>
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 7d18f0a1

 upstream.

Sometimes a GPIO is fetched with NULL as parent device, and
that is just fine. So under these circumstances, avoid using
dev_name() to provide a name for the GPIO line.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Daniel Rosenberg <drosen@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 4b66af2d

 upstream.

Key extensions (struct sadb_key) include a user-specified number of key
bits.  The kernel uses that number to determine how much key data to copy
out of the message in pfkey_msg2xfrm_state().

The length of the sadb_key message must be verified to be long enough,
even in the case of SADB_X_AALG_NULL.  Furthermore, the sadb_key_len value
must be long enough to include both the key data and the struct sadb_key
itself.

Introduce a helper function verify_key_len(), and call it from
parse_exthdrs() where other exthdr types are similarly checked for
correctness.

Signed-off-by: Kevin Easton <kevin@guarana.org>
Reported-by:  <syzbot+5022a34ca5a3d49b84223653fab632dfb7b4cf37@syzkaller.appspotmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Zubin Mithra <zsm@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 327ea4ad upstream.

Avoid that complaints similar to the following appear in the kernel log
if the number of zones is sufficiently large:

  fio: page allocation failure: order:9, mode:0x140c0c0(GFP_KERNEL|__GFP_COMP|__GFP_ZERO), nodemask=(null)
  Call Trace:
  dump_stack+0x63/0x88
  warn_alloc+0xf5/0x190
  __alloc_pages_slowpath+0x8f0/0xb0d
  __alloc_pages_nodemask+0x242/0x260
  alloc_pages_current+0x6a/0xb0
  kmalloc_order+0x18/0x50
  kmalloc_order_trace+0x26/0xb0
  __kmalloc+0x20e/0x220
  blkdev_report_zones_ioctl+0xa5/0x1a0
  blkdev_ioctl+0x1ba/0x930
  block_ioctl+0x41/0x50
  do_vfs_ioctl+0xaa/0x610
  SyS_ioctl+0x79/0x90
  do_syscall_64+0x79/0x1b0
  entry_SYSCALL_64_after_hwframe+0x3d/0xa2

Fixes: 3ed05a98

 ("blk-zoned: implement ioctls")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Shaun Tancheff <shaun.tancheff@seagate.com>
Cc: Damien Le Moal <damien.lemoal@hgst.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>