Add the initial support for the Warp7 board.

For more information about this reference design, please visit:

https://www.element14.com/community/docs/DOC-79058/l/warp-7-the-next-generation-wearable-reference-platform



Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Several dts files set a bit in the SPEED field for pads
RGMII_{R,T}{XC,D0,D1,D2,D3,X_CTL}, but that doesn't exist. Writing there
doesn't have an effect and the bit reads as zero.

Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

bc677ff4

 adds a device-tree property
to specify that an external watchdog reset is used to reset other
portions of the board and not just the IMX6 SoC.

This adds the property to the proper watchdog as well as the pinmux for
the Gateworks Ventana boards that use this external watchdog reset to
reset the PMIC which will reset all the PMIC power rails and not just
a chip-level IMX6 reset. This helps to work around various system issues
that can cause a hang when coming out of reset.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This commit adds definition for cpu_on, cpu_off and cpu_suspend
commands.  These definitions must match the corresponding PSCI
definitions in boot monitor.

Having those command and corresponding PSCI support in boot monitor
allows run time CPU hot plugin.

Link: http://lkml.kernel.org/r/E1b8koV-0004Hf-2j@rmk-PC.armlinux.org.uk


Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Pratyush Anand <panand@redhat.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Simon Horman <horms@verge.net.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Replace the non-standard vendor prefix stm with st for
STMicroelectronics. The drivers do not specify the vendor prefixes
since the I2C Core strips them away from the DT provided compatible
string. Therefore, changing existing device trees does not have any
impact on device detection.

Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Rob Herring <robh@kernel.org>

The inet86dz board is a board used in 7" tablets from various oems.

These tablets are a23 based 7" tablets featuring a 1024x600 LCD,
512MB RAM, 4G NAND, rtl8188etv usb wifi, gsl1680 touchschreen,
micro-sd slot, 3.5mm headphone jack and a micro-usb otg connector
which doubles as charging port.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The Polaroid MID2407PXE03 is an a23 based 7" tablet based on a M86_MB V2.0
PCB, featuring a 800x480 LCD, 512MB RAM, 4G NAND, esp8089 wifi, gsl1680
touchschreen, micro-sd slot, 3.5mm headphone jack and a micro-usb otg
connector which doubles as charging port.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

This results in quite a nice cleanup for this dts file.

As an added bonus this also enables backlight, regulator and full otg
support. I've tested that all these works as advertised.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

This results in quite a nice cleanup for this dts file.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add a drivevbus-supply property so that the drivevbus regulator
reports the right voltage value.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Copy sun8i-q8-common.dtsi to sun8i-reference-design-tablet.dtsi. This
is part of renaming all the sun?i-q8-common.dtsi files to
sun?i-reference-design-tablet.dtsi since most of the hw-config in there
is shared by all sunxi tablets.

Note that in this case we keep sun5i-q8-common.dtsi as it is shared
between a23 / a33 q8 tablets. Also we leave the usb-wifi config in
there (rather then in sun8i-reference-design-tablet.dtsi) as most
sun8i tablets use sdio wifi rather then usb wifi.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

This results in a nice cleanup for this dts file.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

This results in quite a nice cleanup for this dts file.

Note as a side-effect this also enables the on board speaker / headphones
out. I've tested that this works as advertised.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Remove all mention of q8 from sun5i-reference-design-tablet.dtsi.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Set lradc vref to the actual avcc ldo, rather then to the fixed 3v0
regulator from common-regulators.dtsi.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Rename sun5i-q8-common.dtsi to sun5i-reference-design-tablet.dtsi. This
is part of renaming all the sun?i-q8-common.dtsi files to
sun?i-reference-design-tablet.dtsi since most of the hw-config in there
is shared by all sunxi tablets.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

This is a preparation patch for renaming sun5i-q8-common.dtsi to
sun5i-reference-design-tablet.dtsi and sharing it between all
the A13 tablet dts files.

Since we only have a panel config for the 18 tablets (for now) move
this to the q8 specific dts file.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Rename sunxi-q8-common.dtsi to sunxi-reference-design-tablet.dtsi. This
is part of renaming all the sun?i-q8-common.dtsi files to
sun?i-reference-design-tablet.dtsi since most of the hw-config in there
is shared by all sunxi tablets.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Commit 0dfd582e

 ("watchdog: qcom: use timer devicetree
binding") moved to use the watchdog as a subset timer
register block. Some devices have the watchdog completely
standalone with slightly different register offsets as
well so let's account for the differences here.

The existing "kpss-standalone" compatible string doesn't
make it entirely clear exactly what the device is so
rename to "kpss-wdt" to reflect watchdog timer
functionality. Also update ipq4019 DTS with an SoC
specific compatible.

Signed-off-by: Matthew McClintock <mmcclint@codeaurora.org>
Signed-off-by: Thomas Pedersen <twp@codeaurora.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Update the compatible string to align with driver and also
add SoC specific string to DTS.

CC: linux-watchdog@vger.kernel.org
Signed-off-by: Matthew McClintock <mmcclint@codeaurora.org>
Signed-off-by: Thomas Pedersen <twp@codeaurora.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Building both ARMv4 and ARMv5 dtbs when SOC_SAM_V4_V5 is an issue for
kernelci because it will then attempt to boot ARMv4 kernels on at91sam9
which doesn't work.

Use CONFIG_SOC_AT91RM9200 and CONFIG_SOC_AT91SAM9 instead.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Separate the definitions for the emac and the gmac in different files and
include them in the final board dts that uses them.

Solves:
Warning (unit_address_vs_reg): Node /ahb/apb/ethernet@f0028000 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /ahb/apb/ethernet@f802c000 has a unit name, but no reg property

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Add a reg property in the endpoint node as documented in
Documentation/devicetree/bindings/media/video-interfaces.txt

Solves:
Warning (unit_address_vs_reg): Node /ahb/apb/isi@f8048000/port/endpoint@0 has a unit name, but no reg property

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

The ISI is only present on the at91sam9g25, move the definition to the
at91sam9g25ek board dts to avoid warnings.

Solves the following warning for other 9x5ek boards:
Warning (unit_address_vs_reg): Node /ahb/apb/isi@f8048000 has a unit name, but no reg property

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

i2c-gpio doesn't need a reg property. Change the node names to i2c-gpio-x
as used in other dts to remove the unit-address.

Solves:
Warning (unit_address_vs_reg): Node /i2c@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /i2c@1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /i2c@2 has a unit name, but no reg property

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

vcc_3v3_reg is a fixed regulator and doesn't need a reg property. Remove
its unit-address.

Solves:
Warning (unit_address_vs_reg): Node /fixedregulator@0 has a unit name, but no reg property

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Remove the unit-address from the oneiwire node as it doesn't have a reg
property.

Solves:
Warning (unit_address_vs_reg): Node /onewire@0 has a unit name, but no reg property

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

vcc_mmc1_reg is a fixed regulators and doesn't need a reg property. Remove
its unit-address.

Solves:
Warning (unit_address_vs_reg): Node /fixedregulator@2 has a unit name, but no reg property

Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

vcc_3v3_reg and vcc_mmc1_reg are fixed regulators and don't need a
reg property. Remove their unit-address.

Solves:
Warning (unit_address_vs_reg): Node /fixedregulator@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /fixedregulator@1 has a unit name, but no reg property

Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

vcc_3v3_reg and vcc_mmc1_reg are fixed regulators and don't need a reg
property. Remove their unit-address.

Solves:
Warning (unit_address_vs_reg): Node /fixedregulator@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /fixedregulator@1 has a unit name, but no reg property

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

vcc_mmc0_reg is a fixed regulator and doesn't need a reg property. Remove
its unit-address.

Solves:
Warning (unit_address_vs_reg): Node /fixedregulator@0 has a unit name, but no reg property

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

lcd_bus has never been mainlined and is replaced by the atmel_hlcdc driver.
Remove stale nodes.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Endpoint nodes have a reg property. Add their mandatory unit-address.

This solves:
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep0 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep1 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep2 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep3 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep4 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep5 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep6 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep7 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep8 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep9 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep10 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep11 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep12 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep13 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep14 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep15 has a reg or ranges property, but no unit name

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

The triggers don't need a reg property, remove it when prenset. Also remove
the unit-address from their name.

This solves:
Warning (unit_address_vs_reg): Node /ahb/apb/adc@fc034000/trigger@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /ahb/apb/adc@fc034000/trigger@1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /ahb/apb/adc@fc034000/trigger@2 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /ahb/apb/adc@fc034000/trigger@3 has a unit name, but no reg property

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Simon Horman told me that R8A7792 has ADSP clock based on an incorrect
table in the most recent R-Car gen2 manual. But when I received that manual
I discovered that this is false: R8A7792 is the only Gen 2 SoC that doesn't
have ADSP at all.  Accordingly remove the ADSP clock from DT for the
r8a7792.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Despite the fact that QSPI clock has PLL1/VCOx1/4 clock as a parent, the
latter hasn't been added to the R8A7792 device tree. This patch corrects
that oversight.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Lots of platforms contain clocks which if turned off would prove fatal.
The only way to recover is to restart the board(s).  This driver takes
references to clocks which are required to be always-on.  The Common
Clk Framework will then take references to them.  This way they will
not be turned off during the clk_disabled_unused() procedure.

In this patch we are identifying clocks, which if gated would render
the STiH410 development board unserviceable.

Signed-off-by: Lee Jones <lee.jones@linaro.org>

Now that we have a different clock representation, switch to it.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20160629190535.11855-15-maxime.ripard@free-electrons.com

The clearfog DTS should not be defining the on-board phy, this device
is located on the microsom.  Remove the duplicated definition.

Reported-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

This patch adds the device tree to support Toradex Apalis TK1 a
computer on module which can be used on different carrier boards.

The module consists of a Tegra TK1 SoC, a PMIC solution, 2 GB of DDR3L
RAM, a bunch of level shifters, an eMMC, a TMP451 temperature sensor
chip, an I210 gigabit Ethernet controller and a SGTL5000 audio codec.
Furthermore, there is a Kinetis MK20DN512 companion micro controller for
analogue, CAN and resistive touch functionality which is not yet
supported. Anything that is not self contained on the module is disabled
by default.

The device tree for the Evaluation Board includes the module's device
tree and enables the supported peripherals of the carrier board (the
Evaluation Board supports almost all of them).

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>