Merge series from Stephan Gerhold <stephan@gerhold.net>:

This series adds a simple driver and DT schema for the Awinic AW8738
audio amplifier. It's fairly simple - the main difference to
simple-amplifier is that there is a "one-wire pulse control" that
allows configuring the amplifier to one of a few pre-defined modes.
This can be used to configure the speaker-guard function (primarily
the power limit for the amplifier).

The "adata->i2s_irq" variable is unsigned so the error handling
will not work.

Fixes: 87d71a12

 ("ASoC: amd: pcm-dma: Use platform_get_irq() to get the interrupt")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20220304131256.GA28739@kili


Signed-off-by: Mark Brown <broonie@kernel.org>

DETECT_MODE and PLL_START must be zero while HP_PDN and ADC_PDN are
both 1. If this condition is broken it can discharge FILT+ and it
can then take up to 1 second for FILT+ to recharge.

There is no workaround required for this, simply avoiding settings
and sequences that would break the requirement. The driver already
meets the requirement.

But it is not obvious from reading the code that this requirement
exists, or what is ensuring it is met. So it would not currently be
obvious to someone changing the code that there is certain special
behaviour that must be maintained.

To avoid accidental breakage in the future:

- Add comments into the register definitions to warn about this so
  that anyone changing the code around DETECT_MODE and PLL_START is
  aware of this requirement.

- Add a comment where PLL_START is written to 1 to highlight the
  requirement and why it is satisfied.

- Add a comment in cs42l42_setup_hs_type_detect() when DETECT_MODE is
  initialized.

Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220304144015.398656-1-rf@opensource.cirrus.com


Signed-off-by: Mark Brown <broonie@kernel.org>

The parts supported by this driver can have product-specific
firmware and tunings files. Typically these have been used on
embedded systems where the manufacturer is responsible for
installing the correct product-specific firmware files into
/lib/firmware. However, the linux-firmware repository places all
available firmwares into /lib/firmware and it is up to the driver to
select the correct product-specific firmware from that directory.

For example a product containing four smart amplifiers may provide
firmware specific for that product and each of the amplifiers may
have coefficient files containing tunings for their placement in the
mechanical design.

This change extends firmware (wmfw) and coefficient (bin) filenames
to be of the general form:

<cirrus/>part-dspN-fwtype<-system_name<-asoc_component_prefix>>.type

Where the cirrus subdirectory, system_name and asoc_component_prefix
are optional.

New files will be placed in the cirrus subdirectory to avoid
polluting the main /lib/firmware/ location. The generic name must be
searched in /lib/firmware before /lib/firmware/cirrus so that a
generic file in the new location does not override existing
product-specific files in the legacy location.

The search order for firmware files is:
  - cirrus/part-dspN-fwtype-system_name-asoc_component_prefix.wmfw
  - cirrus/part-dspN-fwtype-system_name.wmfw
  - part-dspN-fwtype.wmfw
  - cirrus/part-dspN-fwtype.wmfw

- Qualifications are added to the filename so that rightwards is more
  specific.
- The system_name is provided by the codec driver.
- The asoc_component_prefix is used to identify tunings for individual
  parts because it would already exist to disambiguate the controls
  and it makes it obvious which firmware file applies to which device.

The optional coefficient file must have the same filename
construction as the discovered wmfw except:
  - where the wmfw has only system_name then the bin file can
    optionally include the asoc_component_prefix. This is to allow a
    common wmfw for all amps but separate tunings per amp.

Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220303155016.122125-1-simont@opensource.cirrus.com


Signed-off-by: Mark Brown <broonie@kernel.org>

As the potential failure of the clk_enable(),
it should be better to check it and return error
if fails.

Fixes: ab6f6d85

 ("ASoC: fsi: add master clock control functions")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20220302062844.46869-1-jiasheng@iscas.ac.cn


Signed-off-by: Mark Brown <broonie@kernel.org>

SC7280 config selected WCD938X instead of WCD938X_SDW Soundwire codecs.
WCD938X_SDW actually selects WCD938X, so directly selecting WCD938X results
in unmet dependencies and below warning

WARNING: unmet direct dependencies detected for SND_SOC_WCD938X
  Depends on [n]: SOUND [=y] && !UML && SND [=y] && SND_SOC [=m]
 && SND_SOC_WCD938X_SDW [=n] && (SOUNDWIRE [=n] || !SOUNDWIRE [=n])
  Selected by [m]:
  - SND_SOC_SC7280 [=m] && SOUND [=y] && !UML && SND [=y]
 && SND_SOC [=m] && SND_SOC_QCOM [=m] && (I2C [=y] && SOUNDWIRE [=n] ||
 COMPILE_TEST [=y])

Fix this issue by selecting WCD SoundWire codecs instead of component driver.

Fixes: 57350bd4

 ("ASoC: qcom: SC7280: Add machine driver")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220304160934.32010-1-srinivas.kandagatla@linaro.org


Signed-off-by: Mark Brown <broonie@kernel.org>

cs35l41_private is not used on cs35l41_handle_pdata

Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220304150721.3802-5-tanureal@opensource.cirrus.com


Signed-off-by: Mark Brown <broonie@kernel.org>

This device only has 4 TX channels.

Fixes: fe1024d5

 ("ASoC: cs35l41: Combine adjacent register writes")
Signed-off-by: Lucas Tanure <tanureal@opensource.cirrus.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220304150721.3802-3-tanureal@opensource.cirrus.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Changes:
1. Revise rt5682s_sar_power_mode and rt5682s_headset_detect to be more
   rational.
2. Manually set to the jack-unplugging state via rt5682s_headset_detect
   during going to suspend. Close unnecessary powers and prepare for
   re-detecting the CBJ during resuming.
3. Simplize rt5682s_resume.

Signed-off-by: Derek Fang <derek.fang@realtek.com>
Link: https://lore.kernel.org/r/20220307102154.26065-1-derek.fang@realtek.com


Signed-off-by: Mark Brown <broonie@kernel.org>

As the potential failure of the wm8350_register_irq(),
it should be better to check it and return error if fails.
Also, use 'free_' in order to avoid the same code.

Fixes: a6ba2b2d

 ("ASoC: Implement WM8350 headphone jack detection")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220304023821.391936-1-jiasheng@iscas.ac.cn


Signed-off-by: Mark Brown <broonie@kernel.org>

This node pointer is returned by of_parse_phandle() with refcount
incremented in this function.
Calling of_node_put() to avoid the refcount leak.

Fixes: 531f67e4

 ("ASoC: at91sam9g20ek-wm8731: convert to dt support")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20220307124539.1743-1-linmq006@gmail.com


Signed-off-by: Mark Brown <broonie@kernel.org>

The "adata->i2s_irq" variable is unsigned so this error handling
code will not work.

Fixes: 87d71a12

 ("ASoC: amd: pcm-dma: Use platform_get_irq() to get the interrupt")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20220304131534.GD28739@kili


Signed-off-by: Mark Brown <broonie@kernel.org>

The "adata->pdm_irq" variable is unsigned so the error handling will
not work.

Fixes: 87d71a12

 ("ASoC: amd: pcm-dma: Use platform_get_irq() to get the interrupt")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20220304131335.GB28739@kili


Signed-off-by: Mark Brown <broonie@kernel.org>

The "adata->i2s_irq" is unsigned so this error handling will not
work.

Fixes: 3304a242

 ("ASoC: amd: Use platform_get_irq_byname() to get the interrupt")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20220304131449.GC28739@kili


Signed-off-by: Mark Brown <broonie@kernel.org>

The Awinic AW8738 is a simple audio amplifier using a single GPIO.
The main difference to simple-amplifier is that there is a "one-wire
pulse control" that allows configuring the amplifier to one of a few
pre-defined modes. This can be used to configure the speaker-guard
function (primarily the power limit for the amplifier).

Add a simple driver that allows setting it up in the device tree
with a specified mode number.

Signed-off-by: Jonathan Albrieux <jonathan.albrieux@gmail.com>
Co-developed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20220304102452.26856-3-stephan@gerhold.net


Signed-off-by: Mark Brown <broonie@kernel.org>

Add a DT schema for describing Awinic AW8738 audio amplifiers. They are
fairly simple and controlled using a single GPIO. The number of pulses
during power up selects one of a few pre-defined operation modes. This
can be used to configure the speaker-guard function (primarily the
power limit for the amplifier).

Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20220304102452.26856-2-stephan@gerhold.net


Signed-off-by: Mark Brown <broonie@kernel.org>

This patch fix the second dai driver's dai widget can't connect to the
endpoint. Because "bt-sco-pcm" and "bt-sco-pcm-wb" dai driver have the
same stream_name, so it will cause they have the same widget name.
Therefor it will just create only one route when do snd_soc_dapm_add_route
that only find the widget through the widget name.

Signed-off-by: Jiaxin Yu <jiaxin.yu@mediatek.com>
Link: https://lore.kernel.org/r/20220302013533.29068-1-jiaxin.yu@mediatek.com


Signed-off-by: Mark Brown <broonie@kernel.org>

pcm name can be "Analog" and "Alt Analog", cpcm->name can be
"Analog Codec DAI" and "Alt Analog Codec DAI". When pcm_name
is "Analog", "Analog Codec DAI" and "Alt Analog Codec DAI" are
both satisfy the 'if (strstr(cpcm->name, pcm_name))' condition,
which may cause the returned cpcm to be "Alt Analog Codec DAI".

Even if we get the pcm name by id, and "Analog Codec DAI" goes
into the loop before "Alt Analog Codec DAI", but I still think
we'd better have multiple insurances against unexpected return
values. After, we can correctly return the expected result
even if other relevant places are changed.

Signed-off-by: Meng Tang <tangmeng@uniontech.com>
Link: https://lore.kernel.org/r/20220302094351.3487-1-tangmeng@uniontech.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Merge series from Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>:

Two cleanups to remove an unused filename and typos, and one addition
of an ACPI matching table for a Dell SoundWire SKU without local
microphones.

The main change is the addition of a common 'sof-ssp-amp' machine
driver for devices with amplifiers only (no headset codec) and
different connections using I2S links (Bluetooth offload, HDMI
receiver). It's likely that the amplifier will be swapped out by OEMs,
this machine driver provides a relatively generic solution to avoid
copy-paste of similar solutions.

The copy_to/from_user() functions return the number of bytes remaining
to be copied.  This function needs to return negative error codes
because snd_soc_pcm_component_copy_user() treats positive returns as
success in soc_component_ret().

Fixes: 7d720955

 ("ASoC: qcom: Add support for codec dma driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20220301081104.GB17375@kili


Signed-off-by: Mark Brown <broonie@kernel.org>

There is one call trace that snd_soc_register_card()
->snd_soc_bind_card()->soc_init_pcm_runtime()
->snd_soc_dai_compress_new()->snd_soc_new_compress().
In the trace the 'codec_dai' transfers from card->dai_link,
and we can see from the snd_soc_add_pcm_runtime() in
snd_soc_bind_card() that, if value of card->dai_link->num_codecs
is 0, then 'codec_dai' could be null pointer caused
by index out of bound in 'asoc_rtd_to_codec(rtd, 0)'.
And snd_soc_register_card() is called by various platforms.
Therefore, it is better to add the check in the case of misusing.
And because 'cpu_dai' has already checked in soc_init_pcm_runtime(),
there is no need to check again.
Adding the check as follow, then if 'codec_dai' is null,
snd_soc_new_compress() will not pass through the check
'if (playback + capture != 1)', avoiding the leftover use of
'codec_dai'.

Fixes: 467fece8

 ("ASoC: soc-dai: move snd_soc_dai_stream_valid() to soc-dai.c")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/1634285633-529368-1-git-send-email-jiasheng@iscas.ac.cn


Signed-off-by: Mark Brown <broonie@kernel.org>

In dmaengine_pcm_set_runtime_hwparams() period_bytes_min is hardcoded to
256. For some applications that may be too big. This patch changes that
to calculate the value based on dma_data->maxburst. The correct value
would be maxburst multiplied by the address width of the hardware FIFO.
Unfortunately the address width is dynamically calculated based on the
stream parameters and is not known at open time, so the worst case
is chosen here which is 8 bytes, the maximum that is supported by
dmaengine drivers.
Not all drivers may set a maxburst value, so we fall back to the
previously used hardcoded value of 256 bytes.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20220301113446.1053171-1-s.hauer@pengutronix.de


Signed-off-by: Mark Brown <broonie@kernel.org>

As the potential failure of the clk_enable(),
it should be better to check it, as same as clk_prepare_enable().

Fixes: c9afc183

 ("ASoC: dwc: Disallow building designware_pcm as a module")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20220301084742.3751939-1-jiasheng@iscas.ac.cn


Signed-off-by: Mark Brown <broonie@kernel.org>

Uses asoc_substream_to_rtd() helper.

Signed-off-by: Zhen Ni <nizhen@uniontech.com>
Link: https://lore.kernel.org/r/20220302081502.25367-1-nizhen@uniontech.com


Signed-off-by: Mark Brown <broonie@kernel.org>

As the potential failure of the clk_enable(),
it should be better to check it and return error if fals.

Fixes: cbaadf0f

 ("ASoC: atmel_ssc_dai: refactor the startup and shutdown")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20220301090637.3776558-1-jiasheng@iscas.ac.cn


Signed-off-by: Mark Brown <broonie@kernel.org>

As the potential failure of the clk_enable(),
it should be better to check it, like mxs_saif_trigger().

Fixes: d0ba4c01

 ("ASoC: mxs-saif: set a base clock rate for EXTMASTER mode work")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20220301081717.3727190-1-jiasheng@iscas.ac.cn


Signed-off-by: Mark Brown <broonie@kernel.org>

Support configuration with SoundWire RT1316 amplifiers on link0 and
link1, and RT711 on link2 for headphone/headset. This product does not
support local microphones.

Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220301194903.60859-9-pierre-louis.bossart@linux.intel.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Add support of CS35L41 amplifier to the machine driver, as well as
the support of HDMI playback and BT offload DAI Link.

Rename the driver to a generic name to support different amplifiers
from different vendors.

Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Brent Lu <brent.lu@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220301194903.60859-8-pierre-louis.bossart@linux.intel.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Implement cs35l41 support code in this common module so it could be
shared between multiple SOF machine drivers.

Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Brent Lu <brent.lu@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220301194903.60859-7-pierre-louis.bossart@linux.intel.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Move the code related to rt1308 dai link to the realtek common module.
It creates a clean base to add more amplifier support to this machine
driver in the future.

Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Brent Lu <brent.lu@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220301194903.60859-6-pierre-louis.bossart@linux.intel.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Move sof_realtek_common.o to a dedicated module like the module to
support maxim amplifiers.

Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Brent Lu <brent.lu@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220301194903.60859-5-pierre-louis.bossart@linux.intel.com


Signed-off-by: Mark Brown <broonie@kernel.org>

Adding separate I2S machine driver for RT1308.

Adding support for HDMI-In capture via I2S in slave mode configuration.

Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: balamurugan.c <balamurugan.c@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220301194903.60859-4-pierre-louis.bossart@linux.intel.com


Signed-off-by: Mark Brown <broonie@kernel.org>

copy/paste spelling issues with platforms and buttons.

Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: FRED OH <fred.oh@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220301194903.60859-3-pierre-louis.bossart@linux.intel.com


Signed-off-by: Mark Brown <broonie@kernel.org>

We've been using a default firmware name for each PCI/ACPI/OF platform
for a while. The machine-specific sof_fw_filename is in practice not
different from the default, and newer devices don't set this field, so
let's remove the redundant definitions.

When OEMs modify the base firmware, they can keep the same firmware
name but store the file in a separate directory.

Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20220301194903.60859-2-pierre-louis.bossart@linux.intel.com


Signed-off-by: Mark Brown <broonie@kernel.org>

WSA SoundWire Controller does not support Clock stop and performs a soft reset
on suspend  resume path. Its recommended that WSA881x codecs connected to this
are also reset using a hard reset during suspend resume.

So this codec driver performs a hard reset during suspend resume cycle.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220228144235.24208-1-srinivas.kandagatla@linaro.org


Signed-off-by: Mark Brown <broonie@kernel.org>

Merge series from Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>:

This patch set is to add power domains support for RX, TX and VA macros.

As part of moving to remove the old style defines for the bus clocks update
the es7241 driver to use more modern terminology for clocking.

Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20220222223300.3120298-1-broonie@kernel.org


Signed-off-by: Mark Brown <broonie@kernel.org>

As part of moving to remove the old style defines for the bus clocks update
the max98927 driver to use more modern terminology for clocking.

Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20220222234026.712070-10-broonie@kernel.org


Signed-off-by: Mark Brown <broonie@kernel.org>

As part of moving to remove the old style defines for the bus clocks update
the max98926 driver to use more modern terminology for clocking.

Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20220222234026.712070-9-broonie@kernel.org


Signed-off-by: Mark Brown <broonie@kernel.org>

As part of moving to remove the old style defines for the bus clocks update
the max98925 driver to use more modern terminology for clocking.

Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20220222234026.712070-8-broonie@kernel.org


Signed-off-by: Mark Brown <broonie@kernel.org>