The lamobo-r1 board, sometimes called the BPI-R1 but not labelled as such
on the PCB, is meant as a A20 based router board. As such the board comes
with a built-in switch chip giving it 5 gigabit ethernet ports, and it
has a large empty area on the pcb with mounting holes which will fit a
2.5 inch harddisk. To complete its networking features it has a
Realtek RTL8192CU for WiFi 802.11 b/g/n.

Signed-off-by: Jelle de Jong <jelledejong@powercraft.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Enable the OTG USB controller on the A7HD.

Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Enable the otg/drc usb controller on the MK802.

Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

A23/A33 Q8 tablets have an X-Powers AXP223 PMIC connected via RSB. Its
regulators provide power to various parts of the SoC and the board.

Also add lcd regulator supply for simplefb and update the existing
vmmc-supply for mmc0.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

This board has a X-Powers AXP223 PMIC connected via RSB. Its regulators
provide power to various parts of the SoC and the board.

Also update the regulator supply phandles.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Enable the otg/drc usb controller on the Olimex A20 EVB.

Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>

Enable the otg/drc usb controller on the MK808C.

Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>

pinctrl-sunxi uses 3 cells to describe interrupt, not 2. It's bank
number, pin number and flags.

Signed-off-by: Krzysztof Adamski <k@japko.eu>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The A83T does not have a 32.768 kHz low speed oscillator, either as
an external crystal or input. It has a 16 MHz RC-based (inaccurate)
internal oscillator, which is then divided by 512 for a clock close
to 32 kHz.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

i2c3 and uart4 are available on the GPIO header. Though these pins only
have this one special function, the user may choose to use them as GPIOs
instead.

Since our policy is not to choose what function to present on the GPIO
headers of development boards, remove them.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Convert the Itead Iteaduino A10 to use the new common itead core dtsi.

Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The Itead Ibox is a multi board device based on the Allwinner A20 SoC.
It contains the A20 Itead Core module and a base board for the external
interfaces.

The core module comes with 4GB NAND and 1GB DDR RAM.

The base board to which the core board is connected provides 3 USB 2.0 Host
ports, 1 USB 2.0 OTG, 1 uSD slot, 10/100 Ethernet port, HDMI, IR receiver,
SPDIF and a 32-pin GPIO header. This header expands the features of core
board by exposing the VGA pins, audio In/Out pins, SATA, SPI, I2C, UARTS,
USB-OTG and power.

Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Itead have a core module board that can be populated with either
an Allwinner A10 or A20 SoC. This patch creates a common dtsi
which these boards can use.

Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

mmc2 has a special pin for eMMC hardware reset, which is controllable
from the controller. Add the "mmc-cap-hw-reset" property to denote that
this controller supports this function, and the pins are actually used.

Also increase the signal drive strength for mmc2 pins, for HS-DDR mode
support.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

mmc2 has a special pin for eMMC hardware reset, which is controllable
from the controller. Add the "mmc-cap-hw-reset" property to denote that
this controller supports this function, and the pins are actually used.

Also increase the signal drive strength for mmc2 pins, for HS-DDR mode
support.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

mmc2_8bit_pins is used with eMMC chips, which also have a reset pin.
The MMC controller also has a reset output that is supported.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

mmc2_8bit_pins is used with eMMC chips, which also have a reset pin.
The MMC controller also has a reset output that is supported.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

According to Allwinner, only mmc3 supports 8 bit DDR transfers for eMMC.
Switch to mmc3 for the onboard eMMC, and also assign vqmmc for signal
voltage sensing, and "cap-mmc-hw-reset" to denote this instance can use
eMMC hardware reset.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

mmc2 and mmc3 are available on the same pins, with different mux values.
However, only mmc3 supports 8 bit DDR transfer modes.

Since preference for mmc3 over mmc2 is due to DDR transfer modes, just
set the drive strength to 40mA, which is needed for DDR.

This pinmux setting also includes the hardware reset pin for emmc.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

sun9i/A80 MMC controllers have a larger FIFO, and the FIFO DMA
trigger levels can be increased. Also, the mmc module clock parent
has a higher clock rate, and the sample and output delay phases
are different.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

mmc2 has a special pin for eMMC hardware reset, which is controllable
from the controller. Add the "mmc-cap-hw-reset" property to denote that
this controller supports this function, and the pins are actually used.

Also increase the signal drive strength for mmc2 pins, for HS-DDR mode
support.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The current DT doesn't have a phandle to the CPU regulator in the CPU node,
which disables the CPU voltage scaling entirely.

Add that phandle.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Cubietruck Plus is a A83T/H8 based development board. The board has
standard DDR3 SDRAM, AXP818 PMIC/codec, SD/MMC, eMMC, USB 2.0 host
via HSIC USB Hub, USB OTG, SATA via USB bridge, gigabit ethernet,
WiFi, headphone out / mic in, and various GPIO headers.

The board also has an EEPROM on i2c0 which holds the MAC address.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The A83T, like previous Allwinner SoCs, has a watchdog as part of its
timer block. Add a device node for it.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

A83T timer is compatible with that of earlier SOCs.
Just add timer node to enable and re-use it.

Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

H8Homlet Proto v2.0 Board is A83T Dev Board by Allwinner.
It has UART, ethernet, USB, HDMI, etc ports on it.

A83T patches are tested on this board.
It has UART, ethernet, USB, HDMI, etc ports on it.

For FEL mode it needs USB A-A(Male) cable. I used uart0 which
is multiplexed to microsd pins PF2 and PF4.

Enabled UART0 Header(PB9, PB10 pins).

Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Allwinner A83T is new octa-core cortex-a7 SOC.
This adds the basic dtsi, the clocks differs from
earlier sun8i SOCs.

Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
[Maxime: Removed empty chosen node]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add a node describing the focaltech ft5306de4 touchscreen found on
inet97fv2 tablets.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add a node describing the focaltech ft5306de4 touchscreen found on
chuwi-v7-cw0825 tablets.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add a node describing the focaltech ft5406ee8 touchscreen found on
inet-9f-rev03 / qware qw tb-g100 tablets.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

As most platforms implement the PROM serial interface prom_putchar()
add a simple bridge to allow re-using this code for zboot.

Signed-off-by: Alban Bedel <albeu@free.fr>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11811/


Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Add dummy.o to the targets list, and fill targets automatically from
$(vmlinuzobjs) to avoid having to maintain two lists.

When building with XZ compression copy ashldi3.c to the build
directory to use a different object file for the kernel and zboot.
Without this the same object file need to be build with different
flags which cause a rebuild at every run.

Signed-off-by: Alban Bedel <albeu@free.fr>
Cc: linux-mips@linux-mips.org
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11810/


Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Allow BMIPS_GENERIC supported platforms to build GPIO controller
drivers.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Dragan Stancevic <dragan.stancevic@gmail.com>
Cc: cernekee@gmail.com
Cc: jaedon.shin@gmail.com
Cc: gregory.0xf0@gmail.com
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12019/


Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Remove bcm63xx_nvram_get_psi_size() as it now has no users.

Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Cc: MIPS Mailing List <linux-mips@linux-mips.org>
Cc: MTD Maling List <linux-mtd@lists.infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11836/


Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Move Broadcom BCM963xx image tag data structure to include/linux/
so that drivers outside of mach-bcm63xx can use it.

Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Cc: MIPS Mailing List <linux-mips@linux-mips.org>
Cc: MTD Maling List <linux-mtd@lists.infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11832/


Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Use the common definition of the nvram structure from the header file
include/linux/bcm963xx_nvram.h instead of maintaining a separate copy.

Read the version 5 size of nvram data from memory and then call the
new checksum verification function from the header file.

Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Cc: MIPS Mailing List <linux-mips@linux-mips.org>
Cc: MTD Maling List <linux-mtd@lists.infradead.org>
Patchwork: https://patchwork.linux-mips.org/patch/11831/


Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Add missing newline to end of kvm_err string when guest PMAP couldn't be
allocated.

Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11896/


Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

The header arch/mips/kvm/opcode.h defines a few extra opcodes which
aren't in arch/mips/include/uapi/asm/inst.h. There's nothing KVM
specific about them, so lets move them into inst.h where they belong and
delete the header.

Note that mfmcz_op is renamed to mfmc0_op to match the instruction set
manual, and wait_op was already added to inst.h in commit b0a3eae2
("MIPS: inst.h: define COP0 wait op"), merged in v3.16-rc1.

Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11895/


Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Drop the custom cache operation code definitions used by KVM for
emulating guest CACHE instructions, and switch to use the existing
definitions in <asm/cacheops.h>.

Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11893/


Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Most of the cache op codes defined in cacheops.h are split into a 2-bit
cache identifier, and a 3-bit cache op code which does largely the same
thing semantically regardless of the cache identifier.

To allow the use of these definitions by KVM for decoding cache ops,
break the definitions down into parts where it makes sense to do so, and
add masks for the Cache and Op field within the cache op.

Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11892/


Signed-off-by: Ralf Baechle <ralf@linux-mips.org>