On this EVM, the USB cable state has to be determined via the
ID pin tied to a GPIO line. We use the gpio-usb-extcon driver
to read the ID pin and the extcon framework to forward
the USB cable state information to the USB driver so the
controller can be configured in the right mode (host/peripheral).

NOTE: the ports on this board cannot switch roles. They are
configured either host or peripheral by hardwiring the
respective ID pins.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

On this EVM, the USB cable state has to be determined via the
ID pin tied to a GPIO line. We use the gpio-usb-extcon driver
to read the ID pin and the extcon framework to forward
the USB cable state information to the USB driver so the
controller can be configured in the right mode (host/peripheral).

Gets USB peripheral mode to work on this EVM.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

On this EVM, the USB cable state has to be determined via the
ID pin tied to a GPIO line. We use the gpio-usb-extcon driver
to read the ID pin and the extcon framework to forward
the USB cable state information to the USB driver so the
controller can be configured in the right mode (host/peripheral).

Gets USB peripheral mode to work on this EVM.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Looks like I only got half done with moving pinctrl and syscon to
be children of the SCM. I've set up the FAPLL clocks that way already,
but did not complete the job as I copied the syscon values from
am33xx.dtsi.

To make sure the syscon mapping works, I've verfified that we can
set up davinci_emac mac address the same way as cpsw already does
with the syscon mapping. So let's add that too.

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The twl4030 keypad is not wired up in the gta04, so mark it disabled
to avoid pointless initialization.

Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Tony Lindgren <tony@atomide.com>

i.e. configure vpll2 as a supply for the dss rather
than being always-on.

Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add comments to state which GPIO is used for some interrupts.

Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Enabled poweroff through PMIC on GTA04.

Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

GPIO_115 used as irq is in &gpio4, not &gpio3.

Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

mcbsp2 is used in gta04 soundcard config and by default
is disabled so enable it for gta04.

Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Audio should be child of twl node.

Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Fix attribute names.

Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

These add device tree entry for qspi device on dra72-evm.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This allows booting the device with basic functionality.

Note that at least on my revision c board the DDR3 does
not seem to work properly and only some of the memory
can be reliably used.

Also, the mainline u-boot does not seem to properly
initialize the ethernet, so I've been using the old TI
u-boot at:

http://arago-project.org/git/projects/?p=u-boot-omap3.git;a=summary



Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The clocks on dm816x are a bit different from the other omap
variants. The clocks are sourced from a FAPLL (Flying Adder PLL)
unlike on other omaps. Other than that, it's a similar setup
to am33xx with extra muxes and dividers that can be defined
as existing component clocks.

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Similar to other omap variants, let's add dm816x support.

Note that this is based on generated data from the
TI81XX-LINUX-PSP-04.04.00.02 patches published at:

http://downloads.ti.com/dsps/dsps_public_sw/psp/LinuxPSP/TI81XX_04_04/04_04_00_02/index_FDS.html



I've verified the basic functionality, but have not been
able to test all the devices on dm8168-evm.

Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add handling for gta04 tv out chain:
venc -> opa362 -> svideo

Use invert-polarity in venc node because opa362
is doing polarity inversion also.

Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

CM-T3517, CM-T3530 and CM-T3730 features NAND storage chip connected to
GPMC bus.

Add GPMC DT entry into the root DT file omap3-cm-t3x.dtsi, common for
all three modules.

NAND timings are calculated to be safe for CM-T3x devices as it works
now in non DT boot (in this case the timings are updated by U-Boot).

Update GPMC ranges in boards DT files to include all connected devices.

Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

TPS gpio now controls a 5v 500mA TL5209 regulator which may be supply
a fan (such as AFB02505HHB) over J1 connector for various purposes.
Provide device tree node to enable the same.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

AM437x IDK board has a User Switch which we can
program to whatever we want. Because this board
doesn't have a PMIC which can give us power button
presses, let's use this user switch as a gpio-keys
power button.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add twl_power for N950/N9. Start with the simplest configuration to just
enable power off.

Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Let this board report KEY_POWER so upper layers
can decide what to do when power button is pressed.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The AM437x Industrial Development Kit (IDK) is
an application development platform targeted at
industrial communication and control applications.

It comes with a 3-phase motor driver, PROFINET,
PROFIBUS and a few other industrial communication
interfaces.

The board has 1GiB of DDR3 RAM, QSPI NOR flash,
a 100% discrete power design (no PMIC) and an
on-board 2MP camera (not supported with Linux
as of this writing).

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add device tree nodes and pinmux entries for Video Processing
Front End (VPFE) on am437x gp evm.

Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add device tree nodes and pinmux entries for Video Processing
Front End (VPFE) on am437x sk evm.

Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add device tree nodes and pinmux entries for Video Processing
Front End (VPFE) on am43x epos evm.

Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add Video Processing Front End (VPFE) device tree
nodes for AM34xx family of devices.

Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Since phyid is no longer used by pcie driver, this field can be dropped
from the DT.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This fixes english in comments and removes extra empty newline.

Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add CPSW DT binding to beagle X15 DTS in order to
get ethernet working with this board.

Note that we're also adding sleep state which will
place all pins in mux mode 15 - which means "driver
off" - thus conserving power.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The DSS data lines don't need pulls, it's best
to remove them to guarantee signal integrity.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

AM437x Starter Kit already has discrete pullups
for all I2C buses, so we can (and should) remove
internal pulls.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch just makes USB[01]_DRVVBUS signal
explicitly muxed. Note that board already has
a discrete pulldown, so we're not adding any
pulls here.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

AM437x Starter Kit already has discrete pulls
where they are necessary. It's safe (and actually
better) to remove internal pulls.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

By don't relying on implicit MMC0 pulldown we
make sure that pins are marked busy and even
if we have a broken bootloader, MMC0 will
remain functional.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

QSPI doesn't need any pullups of any sort,
let's remove them.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>