Add basic APQ8064 SoC include device tree and support for basic booting on
the IFC6410 board.  Also, keep dtb build list and qcom_dt_match in sorted
order.

Signed-off-by: Kumar Gala <galak@codeaurora.org>

* Move SoC peripherals into an SoC container node
* Move serial enabling into board file (qcom-msm8660-surf.dts)
* Cleanup cpu node to match binding spec, enable-method and compatible
  should be per cpu, not part of the container
* Add GSBI node and configuration of GSBI controller

Signed-off-by: Kumar Gala <galak@codeaurora.org>

* Move SoC peripherals into an SoC container node
* Move serial enabling into board file (qcom-msm8960-cdp.dts)
* Cleanup cpu node to match binding spec, enable-method and compatible
  should be per cpu, not part of the container
* Drop interrupts property from l2-cache node as its not part of the
  binding spec
* Add GSBI node and configuration of GSBI controller

Signed-off-by: Kumar Gala <galak@codeaurora.org>

* Move SoC peripherals into an SoC container node
* Move serial enabling into board file (qcom-apq8074-dragonboard.dts)
* Move spi pinctrl into board file
* Cleanup cpu node to match binding spec, enable-method and compatible
  should be per cpu, not part of the container
* Drop interrupts property from l2-cache node as its not part of the
  binding spec
* Move timer node out of SoC container

Signed-off-by: Kumar Gala <galak@codeaurora.org>

Add support for the 2 SDHC controllers on the DB8074 board.  The first
controller (at 0xf9824900) is connected to an on board soldered eMMC.
The second controller (at 0xf98a4900) is connected to a uSD card slot.

Signed-off-by: Georgi Djakov <gdjakov@mm-sol.com>
Signed-off-by: Kumar Gala <galak@codeaurora.org>

Add the pin control node and pin definitions of SPI8.

Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>

The patch changes fimd node status to OK.

Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

The patch changes fimd node status to OK.

Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

The patch adds s6e8aa0 panel node for trats2.
It adds also trats2 specific properties for DSI
and regulator required by panel.

Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

The patch adds s6e8aa0 panel node for trats.
It adds also trats specific properties for DSI.

Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

This is a common part of DSI node for all Exynos4 boards.

Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

This patch replaces panel bindings for panel initialized by boot loader
with bindings to proper ld9040 panel.

Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

Switch the device tree to the new compatibles introduced in the RTC
drivers to have a common pattern accross all Allwinner SoCs.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The IRQ line used in sun6i-a31.dtsi for the NMI controller is wrong.
This causes a IRQ storm since the NMI controller is repeatedly fired.
This patch fixes this problem assigning the correct IRQ number to the
NMI controller.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Carlo Caione <carlo@caione.org>
Cc: maxime.ripard@free-electrons.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-sunxi@googlegroups.com
Link: http://lkml.kernel.org/r/1395939759-11135-2-git-send-email-carlo@caione.org


Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

move to support of_dma_request_slave_channel() and dma_request_slave_channel.
we add a xlate() to let dma clients be able to find right dma_chan by generic
"dmas" properties in dts.

Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

This patch adds the dts bindings documenation for the Altera SOCFPGA glue
layer for the Synopsys STMMAC ethernet driver.

Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Here we add the necessary device nodes required for successful device
probing and Pinctrl setup for the FSM when booting on an STiH415 (Orly1)
or STiH416 (Orly2) based b2020 development board.

Acked-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by Angus Clark <angus.clark@st.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Here we add the necessary device nodes required for successful device
probing and Pinctrl setup for the FSM when booting on an STiH416 (Orly2).

Acked-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by Angus Clark <angus.clark@st.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

This reverts commit 7e0b4cd0

.

The binding changes need to be done differently as well, let's
take them through netdev, and merge the dts changes in a new
patch here.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Neither Tegra114 nor Tegra124 allow "low power mode" to be configured
on SDIO1 or SDIO3 drive groups. Remove the attempt to configure that
option from the Dalmore and Venice2 DTs.

The Venice2 DT contained duplicate configurations for most sdmmc1_*
pins. Remove the duplicate pins from one of the nodes, and fix the
configuration since the remaining clk pin is output-only.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

This patch adds DTS entries for NMI controller as child of GIC.

Signed-off-by: Carlo Caione <carlo@caione.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-sunxi@googlegroups.com
Cc: mark.rutland@arm.com
Cc: hdegoede@redhat.com
Acked-by:  <maxime.ripard@free-electrons.com>
Link: http://lkml.kernel.org/r/1395256879-8475-3-git-send-email-carlo@caione.org


Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

The patch adds fimd node with display timings for exynos4210-universal device.
It also makes LCD regulators always on. This allow to re-use panel initialized
by boot loader.

Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>

Remove some entries from Dalmore's device tree that attempt to set some
options which aren't supported for the drive_gma pin group.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

As suggested by Olof Johansson at
http://www.spinics.net/lists/arm-kernel/msg314009.html

.
It be better just keeping a "ti,keystone" top-level compatible and
just using that to probe. If so we don't have to touch the file
for new boards in the future.

So use common "ti,keystone" compatible in keystone.c for all boards.

Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Olof Johansson <olof@lixom.net>

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

The UBIFS partition size was incorrectly defined as for 128M NAND,
but on k2hk-evm installed NAND flash size is 512M.
Hence, correct it.

Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

Most of the clock related dt-binding header files are located in
dt-bindings/clock folder. It would be good to keep all the similar
header files at a single location.

Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Reviewed-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

LDO3 and LDO23 need to be enabled in order for soft-reset to work.
Additionally LDO9 needs to be enabled for USB operations.

Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

MDMA1 can support both secure and non-secure AXI transactions. When this
is enabled in the kernel for boards that run in secure mode, we get
imprecise external aborts causing the kernel to oops.

Unhandled fault: imprecise external abort (0x1406) at 0x00000000
Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000007

Suggested-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Tested-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Add generic compatible strings to the respective board DT files.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

Add DT data for OMAP3 N900 board. The board has the following displays:

lcd: LCD panel connected to OMAP's SDI output
tv: analog svideo

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sre@debian.org>
Acked-by: Tony Lindgren <tony@atomide.com>

Add DT data for OMAP3 IGEPv2 board. The board has the following displays:

dvi: uses TFP410 encoder to convert DPI to DVI

Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>

Add DT data for OMAP3 Beagle-xM board. The board has the following displays:

dvi: uses TFP410 encoder to convert DPI to DVI
tv: analog svideo

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>

Add DT data for OMAP3 Beagle board. The board has the following displays:

dvi: uses TFP410 encoder to convert DPI to DVI
tv: analog svideo

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>

Add DT data for OMAP4 SDP board. The board has the following displays:

lcd0: a command mode DSI panel connected to OMAP DSI1 encoder
lcd1: a command mode DSI panel connected to OMAP DSI2 encoder
hdmi: OMAP HDMI output with TPD12S015 ESD/level shifter

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>

Add DT data for OMAP4 Pandaboard. The board has the following displays:

dvi: uses TFP410 encoder to convert DPI to DVI
hdmi: OMAP HDMI output with TPD12S015 ESD/level shifter

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>

Add DT data for OMAP4 display subsystem, which contains the following
blocks:

dss - the wrapper/glue for the display modules
dispc - display controller
dsi - MIPI DSI encoder (two independent modules)
rfbi - MIPI DBI encoder
venc - analog TV encoder
hdmi - HDMI encoder

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>

Add DT data for OMAP3 display subsystem, which contains the following
blocks:

dss - the wrapper/glue for the display modules
dispc - display controller
dsi - MIPI DSI encoder
rfbi - MIPI DBI encoder
venc - analog TV encoder

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>

Add DT data for OMAP2 display subsystem, which contains the following
blocks:

dss - the wrapper/glue for the display modules
dispc - display controller
rfbi - MIPI DBI encoder
venc - analog TV encoder

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>

Set 'ti,set-rate-parent' property for clocks in the dpll4_m4 clock
path, which is used for DSS functional clock. This fixes DSS driver's
clock rate configuration, which needs the rate to be propagated properly
to the divider node (dpll4_m4_ck).

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Christoph Fritz <chf.fritz@googlemail.com>
Tested-by: Marek Belisko <marek@goldelico.com>
Acked-by: Tony Lindgren <tony@atomide.com>

We need to use set-rate-parent for dpll4_m4 clock path, so use the
ti,fixed-factor-clock version which supports set-rate-parent property.

The set-rate-parent flag itself is set in the following patch, this one
just changes the clock driver to ti,fixed-factor-clock without any other
changes.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Christoph Fritz <chf.fritz@googlemail.com>
Tested-by: Marek Belisko <marek@goldelico.com>
Acked-by: Tony Lindgren <tony@atomide.com>