Cyrille Pitchen says:

====================
net/macb: add TX multiqueue support for gem

ChangeLog

v3:
- reduce the number of added #define in macb.h
- simplify the queue initialization
- add some more comments
- use "hw_q" index when dealing with the hardware queue mask and "q" index for
  linux (software) queue index in "for" loops

v2:
fix compilation warnings for netdev_vdbg("%u...", queue - bp->queues, ...) calls

v1:
At the first look this patch may look quite big but it cannot be splitted.
Each queue has its own dedicated IRQ, which should be handled.
Also the Transmit Base Queue Pointer register of each available queue must be
initialized before starting the transmission, otherwise the transmission will be
halted immediately as HRESP errors are likely to occur.
In addition, some fields had to be moved from struct macb into struct macb_queue
so a common code could manage the queues.

This patch was applied to net-next and tested on a sama5d36ek board, which embeds
both macb and gem IPs, to check the backward compatibility.

Also it was tested on a sama5dx FPGA platform with a gem designed to use 3 queues.
Then we used the tc program to set a queue discipline policy as describe in the
Documentation/networking/multiqueue.txt: we successfully used each queue.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

gem devices designed with multiqueue CANNOT work without this patch.

When probing a gem device, the driver must first prepare and enable the
peripheral clock before accessing I/O registers. The second step is to read the
MID register to find whether the device is a gem or an old macb IP.
For gem devices, it reads the Design Configuration Register 6 (DCFG6) to
compute to total number of queues, whereas macb devices always have a single
queue.
Only then it can call alloc_etherdev_mq() with the correct number of queues.
This is the reason why the order of some initializations has been changed in
macb_probe().
Eventually, the dedicated IRQ and TX ring buffer descriptors are initialized
for each queue.

For backward compatibility reasons, queue0 uses the legacy registers ISR, IER,
IDR, IMR, TBQP and RBQP. On the other hand, the other queues use new registers
ISR[1..7], IER[1..7], IDR[1..7], IMR[1..7], TBQP[1..7] and RBQP[1..7].
Except this hardware detail there is no real difference between queue0 and the
others. The driver hides that thanks to the struct macb_queue.
This structure allows us to share a common set of functions for all the queues.

Besides when a TX error occurs, the gem MUST be halted before writing any of
the TBQP registers to reset the relevant queue. An immediate side effect is
that the other queues too aren't processed anymore by the gem.
So macb_tx_error_task() calls netif_tx_stop_all_queues() to notify the Linux
network engine that all transmissions are stopped.

Also macb_tx_error_task() now calls spin_lock_irqsave() to prevent the
interrupt handlers of the other queues from running as each of them may wake
its associated queue up (please refer to macb_tx_interrupt()).

Finally, as all queues have previously been stopped, they should be restarted
calling netif_tx_start_all_queues() and setting the TSTART bit into the Network
Control Register. Before this patch, when dealing with a single queue, the
driver used to defer the reset of the faulting queue and the write of the
TSTART bit until the next call of macb_start_xmit().
As explained before, this bit is now set by macb_tx_error_task() too. That's
why the faulting queue MUST be reset by setting the TX_USED bit in its first
buffer descriptor before writing the TSTART bit.

Queue 0 always exits and is the lowest priority when other queues are available.
The higher the index of the queue is, the higher its priority is.

When transmitting frames, the TX queue is selected by the skb->queue_mapping
value. So queue discipline can be used to define the queue priority policy.

Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Quentin Lambert says:

====================
Remove redundant function

tasklet_hi_enable and tasklet_enable are redundant. Since
tasklet_hi_enable is used only 6 times in 1 file, the first
patch changes calls to the function with calls to tasklet_enable.

The second patch removes tasklet_hi_enable definition.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Quentin Lambert <lambert.quentin@gmail.com>
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Calls to tasklet_hi_enable are replaced by calls to
tasklet_enable since the 2 functions are redundant.

Signed-off-by: Quentin Lambert <lambert.quentin@gmail.com>
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This chip is present on older revisions of the DE2 development kit.

Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

This chip is present on the Nios2 Development Kit 2C35.

Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Firmware 1.12.25.0 added support for QSA module, adding the driver code for it.
Also fixes some ethtool get settings for other module types.

Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Karen Xie says:

====================
cxgb4/cxgbi: misc. fixes for cxgb4i

This patch set fixes cxgb4i's tx credit calculation and adds handling of
additional rx message and negative advice types. It also removes the duplicate
code in cxgb4i to set the outgoing queues of a packet.

Karen Xie (7):
cxgb4i: fix tx immediate data credit check
cxgb4i: fix credit check for tx_data_wr
cxgb4/cxgb4i: set max. outgoing pdu length in the f/w
cxgb4i: add more types of negative advice
cxgb4i: handle non pdu-aligned rx data
cxgb4i: use cxgb4's set_wr_txq() for setting outgoing queues
libcxgbi: fix the debug print accessing skb after it is freed

Sending to net as the fixes are mostly in the network area and it touches
cxgb4's header file (t4fw_api.h).

v2 corrects the "CHECK"s flagged by checkpatch.pl --strict.

v3 splits the 3rd patch from v2 to two separate patches. Adds detailed commit
messages and makes subject more concise. Patch 3/6 also changes the return
value of is_neg_adv() from int to bool.

v4 -- please ignore.

v5 splits the 1st patch from v3 to two separate patches and reduces code
duplication in make_tx_data_wr().

v6 removed the code style cleanup in the 2nd patch. The style update will be
addressed in a separate patch.

v7 updates the 7th patch with more detailed commit message.

v8 removes the duplicate subject lines from the message bodies.

v9 reformatted the commit messages to be max. 80 characters per line.

v10 rebased to net-next tree.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

With debug turned on the debug print would access the skb after it is freed.
Fix it to free the skb after the debug print.

Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

use cxgb4's set_wr_txq() for setting of the tx queue for a outgoing packet.
remove the similar function in cxgb4i.

Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Abort the connection upon receiving of cpl_rx_data, which means the pdu cannot
be recovered from the tcp stream. This generally is due to pdu header
corruption.

Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Treat both CPL_ERR_KEEPALV_NEG_ADVICE and CPL_ERR_PERSIST_NEG_ADVICE as
negative advice.

Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Programs the firmware of the maximum outgoing iscsi pdu length per connection.

Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

make sure any tx credit related checking is done before adding the wr header.

Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Only data skbs need the wr header added while control skbs do not. Make sure
they are treated differently.

Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When building the bcmgenet driver as module, I get:

ERROR: "fixed_phy_register" [drivers/net/ethernet/broadcom/genet/genet.ko] undefined!

commit b0ba512e225d72 ("net: bcmgenet: enable driver to work without device
tree") which added a call to fixed_phy_register. But fixed_phy_register
needs to be exported if used from a module.

Signed-off-by: Mark Salter <msalter@redhat.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch addresses an issue with the level compression of the fib_trie.
Specifically in the case of adding a new leaf that triggers a new node to
be added that takes the place of the old node.  The result is a trie where
the 1 child tnode is on one side and one leaf is on the other which gives
you a very deep trie.  Below is the script I used to generate a trie on
dummy0 with a 10.X.X.X family of addresses.

  ip link add type dummy
  ipval=184549374
  bit=2
  for i in `seq 1 23`
  do
    ifconfig dummy0:$bit $ipval/8
    ipval=`expr $ipval - $bit`
    bit=`expr $bit \* 2`
  done
  cat /proc/net/fib_triestat

Running the script before the patch:

	Local:
		Aver depth:     10.82
		Max depth:      23
		Leaves:         29
		Prefixes:       30
		Internal nodes: 27
		  1: 26  2: 1
		Pointers: 56
	Null ptrs: 1
	Total size: 5  kB

After applying the patch and repeating:

	Local:
		Aver depth:     4.72
		Max depth:      9
		Leaves:         29
		Prefixes:       30
		Internal nodes: 12
		  1: 3  2: 2  3: 7
		Pointers: 70
	Null ptrs: 30
	Total size: 4  kB

What this fix does is start the rebalance at the newly created tnode
instead of at the parent tnode.  This way if there is a gap between the
parent and the new node it doesn't prevent the new tnode from being
coalesced with any pre-existing nodes that may have been pushed into one
of the new nodes child branches.

Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since the real device can segment packets by software, a vlan device
can set TSO/UFO even when the real device doesn't have those features.
Unlike GSO, this allows packets to be segmented after Qdisc.

Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add ephy parameter to rtl8168g.
Also change the common function of rtl8168g from "rtl_hw_start_8168g_1" to
 "rtl_hw_start_8168g". And function "rtl_hw_start_8168g_1" is used for
setting rtl8168g hardware parameters.

Following is the explanation of what hardware parameter change for.
rtl8168g may erroneous judge the PCIe signal quality and show the error bit
on PCI configuration space when in PCIe low power mode.
The following ephy parameters are for above issue.
{ 0x00, 0x0000,	0x0008 }
{ 0x0c, 0x37d0,	0x0820 }
{ 0x1e, 0x0000,	0x0001 }

rtl8168g may return to PCIe L0 from PCIe L0s low power mode too slow.
The following ephy parameter is for above issue.
{ 0x19, 0x8000,	0x0000 }

Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For ports of the switch that we define as "fixed PHYs" such as MoCA, we
would have our Port 7 special handling that would allow us to assert the
link status indication.

For other ports, such as e.g: RGMII_1 connected to a cable modem, we
would rely on whatever the bootloader has left configured, which is a
bad assumption to make, we really need to force the link status
indication here.

Fixes: 246d7f77

 ("net: dsa: add Broadcom SF2 switch driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexander Duyck says:

====================
arch: Add lightweight memory barriers for coherent memory access

These patches introduce two new primitives for synchronizing cache coherent
memory writes and reads.  These two new primitives are:

	dma_rmb()
	dma_wmb()

The first patch cleans up some unnecessary overhead related to the
definition of read_barrier_depends, smp_read_barrier_depends, and comments
related to the barrier.

The second patch adds the primitives for the applicable architectures and
asm-generic.

The third patch adds the barriers to r8169 which turns out to be a good
example of where the new barriers might be useful as they have full
rmb()/wmb() barriers ordering accesses to the descriptors and the DescOwn
bit.

The fourth patch adds support for coherent_rmb() to the Intel fm10k, igb,
and ixgbe drivers.  Testing with the ixgbe driver has shown a processing
time reduction of at least 7ns per 64B frame on a Core i7-4930K.

This patch series is essentially the v7 for:
v4-7:	Add lightweight memory barriers for coherent memory access
v3:	Add lightweight memory barriers fast_rmb() and fast_wmb()
v2:	Introduce load_acquire() and store_release()
v1:	Introduce read_acquire()

The key changes in this patch series versus the earlier patches are:
v7 resubmit:
	- Added Acked-by: Ben Herrenschmidt from v5 to dma_rmb/wmb patch
	- No code changes from previous set, still applies cleanly and builds.
v7:
	- Dropped test/debug patch that was accidentally slipped in
v6:
	- Replaced "memory based device I/O" with "consistent memory" in
	  docs
	- Added reference to DMA-API.txt to explain consistent memory
v5:
	- Renamed barriers dma_rmb and dma_wmb
	- Undid smp_wmb changes in x86 and PowerPC
	- Defined smp_rmb as __lwsync for SMP case on PowerPC
v4:
	- Renamed barriers coherent_rmb and coherent_wmb
	- Added smp_lwsync for use in smp_load_acquire/smp_store_release
v3:
	- Moved away from acquire()/store() and instead focused on barriers
	- Added cleanup of read_barrier_depends
	- Added change in r8169 to fix cur_tx/DescOwn ordering
	- Simplified changes to just replacing/moving barriers in r8169
	- Added update to documentation with code example
v2:
	- Renamed read_acquire() to be consistent with smp_load_acquire()
	- Changed barrier used to be consistent with smp_load_acquire()
	- Updated PowerPC code to use __lwsync based on IBM article
	- Added store_release() as this is a viable use case for drivers
	- Added r8169 patch which is able to fully use primitives
	- Added fm10k/igb/ixgbe patch which is able to test performance
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

This change makes it so that dma_rmb is used when reading the Rx
descriptor.  The advantage of dma_rmb is that it allows for a much
lower cost barrier on x86, powerpc, arm, and arm64 architectures than a
traditional memory barrier when dealing with reads that only have to
synchronize to coherent memory.

In addition I have updated the code so that it just checks to see if any
bits have been set instead of just the DD bit since the DD bit will always
be set as a part of a descriptor write-back so we just need to check for a
non-zero value being present at that memory location rather than just
checking for any specific bit.  This allows the code itself to appear much
cleaner and allows the compiler more room to optimize.

Cc: Matthew Vick <matthew.vick@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The r8169 use a pair of wmb() calls when setting up the descriptor rings.
The first is to synchronize the descriptor data with the descriptor status,
and the second is to synchronize the descriptor status with the use of the
MMIO doorbell to notify the device that descriptors are ready.  This can
come at a heavy price on some systems, and is not really necessary on
systems such as x86 as a simple barrier() would suffice to order store/store
accesses.  As such we can replace the first memory barrier with
dma_wmb() to reduce the cost for these accesses.

In addition the r8169 uses a rmb() to prevent compiler optimization in the
cleanup paths, however by moving the barrier down a few lines and replacing
it with a dma_rmb() we should be able to use it to guarantee
descriptor accesses do not occur until the device has updated the DescOwn
bit from its end.

One last change I made is to move the update of cur_tx in the xmit path to
after the wmb.  This way we can guarantee the device and all CPUs should
see the DescOwn update before they see the cur_tx value update.

Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are a number of situations where the mandatory barriers rmb() and
wmb() are used to order memory/memory operations in the device drivers
and those barriers are much heavier than they actually need to be.  For
example in the case of PowerPC wmb() calls the heavy-weight sync
instruction when for coherent memory operations all that is really needed
is an lsync or eieio instruction.

This commit adds a coherent only version of the mandatory memory barriers
rmb() and wmb().  In most cases this should result in the barrier being the
same as the SMP barriers for the SMP case, however in some cases we use a
barrier that is somewhere in between rmb() and smp_rmb().  For example on
ARM the rmb barriers break down as follows:

  Barrier   Call     Explanation
  --------- -------- ----------------------------------
  rmb()     dsb()    Data synchronization barrier - system
  dma_rmb() dmb(osh) data memory barrier - outer sharable
  smp_rmb() dmb(ish) data memory barrier - inner sharable

These new barriers are not as safe as the standard rmb() and wmb().
Specifically they do not guarantee ordering between coherent and incoherent
memories.  The primary use case for these would be to enforce ordering of
reads and writes when accessing coherent memory that is shared between the
CPU and a device.

It may also be noted that there is no dma_mb().  Most architectures don't
provide a good mechanism for performing a coherent only full barrier without
resorting to the same mechanism used in mb().  As such there isn't much to
be gained in trying to define such a function.

Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: David Miller <davem@davemloft.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is meant to cleanup the handling of read_barrier_depends and
smp_read_barrier_depends.  In multiple spots in the kernel headers
read_barrier_depends is defined as "do {} while (0)", however we then go
into the SMP vs non-SMP sections and have the SMP version reference
read_barrier_depends, and the non-SMP define it as yet another empty
do/while.

With this commit I went through and cleaned out the duplicate definitions
and reduced the number of definitions down to 2 per header.  In addition I
moved the 50 line comments for the macro from the x86 and mips headers that
defined it as an empty do/while to those that were actually defining the
macro, alpha and blackfin.

Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: dsa: two small bug fixes

Here are two small fixes for the DSA slave interface creation code:

- first patch fixes a null pointer de-reference with an invalid PHY
  device pointer while calling phy_connect_direct()

- second path propagates the dsa_slave_phy_setup() error code down to
  its caller: dsa_slave_create
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

In case we cannot attach to our slave netdevice PHY, error out and
propagate that error up to the caller: dsa_slave_create().

Fixes: 0d8bcdd3

 ("net: dsa: allow for more complex PHY setups")
Signed-off-by: Andrey Volkov <andrey.volkov@nexvision.fr>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In case there is no PHY at the designated address on the internal
switch, we would basically de-reference a null pointer here:

dsa_slave_phy_setup(...)
{
	p->phy = ds->slave_mii_bus->phy_map[p->port];
	phy_connect_direct(slave_dev, p->phy, dsa_slave_adjust_link,
				      ^------

This can be triggered when the platform configuration (platform_data or
Device Tree) indicates there should be a PHY device at this address, but
the HW is non-responsive, such that we cannot attach a PHY device at
this specific location.

Fix this by checking the return value prior to calling
phy_connect_direct().

CC: Andrew Lunn <andrew@lunn.ch>
Fixes: b31f65fb

 ("net: dsa: slave: Fix autoneg for phys on switch MDIO bus")
Reported-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Andrey Volkov <andrey.volkov@nexvision.fr>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking updates from David Miller:

 1) New offloading infrastructure and example 'rocker' driver for
    offloading of switching and routing to hardware.

    This work was done by a large group of dedicated individuals, not
    limited to: Scott Feldman, Jiri Pirko, Thomas Graf, John Fastabend,
    Jamal Hadi Salim, Andy Gospodarek, Florian Fainelli, Roopa Prabhu

 2) Start making the networking operate on IOV iterators instead of
    modifying iov objects in-situ during transfers.  Thanks to Al Viro
    and Herbert Xu.

 3) A set of new netlink interfaces for the TIPC stack, from Richard
    Alpe.

 4) Remove unnecessary looping during ipv6 routing lookups, from Martin
    KaFai Lau.

 5) Add PAUSE frame generation support to gianfar driver, from Matei
    Pavaluca.

 6) Allow for larger reordering levels in TCP, which are easily
    achievable in the real world right now, from Eric Dumazet.

 7) Add a variable of napi_schedule that doesn't need to disable cpu
    interrupts, from Eric Dumazet.

 8) Use a doubly linked list to optimize neigh_parms_release(), from
    Nicolas Dichtel.

 9) Various enhancements to the kernel BPF verifier, and allow eBPF
    programs to actually be attached to sockets.  From Alexei
    Starovoitov.

10) Support TSO/LSO in sunvnet driver, from David L Stevens.

11) Allow controlling ECN usage via routing metrics, from Florian
    Westphal.

12) Remote checksum offload, from Tom Herbert.

13) Add split-header receive, BQL, and xmit_more support to amd-xgbe
    driver, from Thomas Lendacky.

14) Add MPLS support to openvswitch, from Simon Horman.

15) Support wildcard tunnel endpoints in ipv6 tunnels, from Steffen
    Klassert.

16) Do gro flushes on a per-device basis using a timer, from Eric
    Dumazet.  This tries to resolve the conflicting goals between the
    desired handling of bulk vs.  RPC-like traffic.

17) Allow userspace to ask for the CPU upon what a packet was
    received/steered, via SO_INCOMING_CPU.  From Eric Dumazet.

18) Limit GSO packets to half the current congestion window, from Eric
    Dumazet.

19) Add a generic helper so that all drivers set their RSS keys in a
    consistent way, from Eric Dumazet.

20) Add xmit_more support to enic driver, from Govindarajulu
    Varadarajan.

21) Add VLAN packet scheduler action, from Jiri Pirko.

22) Support configurable RSS hash functions via ethtool, from Eyal
    Perry.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1820 commits)
  Fix race condition between vxlan_sock_add and vxlan_sock_release
  net/macb: fix compilation warning for print_hex_dump() called with skb->mac_header
  net/mlx4: Add support for A0 steering
  net/mlx4: Refactor QUERY_PORT
  net/mlx4_core: Add explicit error message when rule doesn't meet configuration
  net/mlx4: Add A0 hybrid steering
  net/mlx4: Add mlx4_bitmap zone allocator
  net/mlx4: Add a check if there are too many reserved QPs
  net/mlx4: Change QP allocation scheme
  net/mlx4_core: Use tasklet for user-space CQ completion events
  net/mlx4_core: Mask out host side virtualization features for guests
  net/mlx4_en: Set csum level for encapsulated packets
  be2net: Export tunnel offloads only when a VxLAN tunnel is created
  gianfar: Fix dma check map error when DMA_API_DEBUG is enabled
  cxgb4/csiostor: Don't use MASTER_MUST for fw_hello call
  net: fec: only enable mdio interrupt before phy device link up
  net: fec: clear all interrupt events to support i.MX6SX
  net: fec: reset fep link status in suspend function
  net: sock: fix access via invalid file descriptor
  net: introduce helper macro for_each_cmsghdr
  ...

Pull sound updates from Takashi Iwai:
 "This became a fairly large pull request.  In addition to the usual
  driver updates / fixes, there have been a high amount of cleanups in
  ASoC area, as well as control API helpers and kernel documentations
  fixes touching through the whole tree.

  In the driver side, the biggest changes are the support for new Intel
  SoC found on new x86 machines, and the updates of FireWire dice and
  oxfw drivers.

  Some remarkable items are below:

  ALSA core:
   - PCM mmap code cleanup, removal of arch-dependent codes
   - PCM xrun injection support
   - PCM hwptr tracepoint support
   - Refactoring of snd_pcm_action(), simplification of PCM locking
   - Robustified sequecner auto-load functionality
   - New control API helpers and lots of cleanups along with them
   - Lots of kerneldoc fixes and cleanups

  USB-audio:
   - The mixer resume code was largely rewritten, and the devices with
     quirks are resumed properly.
   - New hardware support: Focusrite Scarlett, Digidesign Mbox1,
     Denon/Marantz DACs, Zoom R16/24

  FireWire:
   - DICE driver updates with better duplex and sync support, including
     MIDI support
   - New OXFW driver for Oxford Semiconductor FW970/971 chipset,
     including the previous LaCie Speakers device.  Fullduplex and MIDI
     support included as well as DICE driver.

  HD-audio:
   - Refactoring the driver-caps quirk handling in snd-hda-intel
   - More consistent control names representing the topology better
   - Fixups: HP mute LED with ALC268 codec, Ideapad S210 built-in mic
     fix, ASUS Z99He laptop EAPD

  ASoC:
   - Conversion of AC'97 drivers to use regmap, bringing us closer to
     the removal of the ASoC level I/O code
   - Clean up a lot of old drivers that were open coding things that
     have subsequently been implemented in the core
   - Some DAPM performance improvements
   - Removal of the now seldom used CODEC mutex
   - Lots of updates for the newer Intel SoC support, including support
     for the DSP and some Cherrytrail and Braswell machine drivers
   - Support for Samsung boards using rt5631 as the CODEC
   - Removal of the obsolete AFEB9260 machine driver
   - Driver support for the TI TS3A227E headset driver used in some
     Chrombeooks

  Others:
   - ASIHPI driver update and cleanups
   - Lots of dev_*() printk conversions
   - Lots of trivial cleanups for the codes spotted by Coccinelle"

* tag 'sound-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (594 commits)
  ALSA: pcxhr: NULL dereference on probe failure
  ALSA: lola: NULL dereference on probe failure
  ALSA: hda - Add "eapd" model string for AD1986A codec
  ALSA: hda - Add EAPD fixup for ASUS Z99He laptop
  ALSA: oxfw: Add hwdep interface
  ALSA: oxfw: Add support for capture/playback MIDI messages
  ALSA: oxfw: add support for capturing PCM samples
  ALSA: oxfw: Add support AMDTP in-stream
  ALSA: oxfw: Add support for Behringer/Mackie devices
  ALSA: oxfw: Change the way to start stream
  ALSA: oxfw: Add proc interface for debugging purpose
  ALSA: oxfw: Change the way to make PCM rules/constraints
  ALSA: oxfw: Add support for AV/C stream format command to get/set supported stream formation
  ALSA: oxfw: Change the way to name card
  ALSA: dice: Add support for MIDI capture/playback
  ALSA: dice: Add support for capturing PCM samples
  ALSA: dice: Support for non SYT-Match sampling clock source mode
  ALSA: dice: Add support for duplex streams with synchronization
  ALSA: dice: Change the way to start stream
  ALSA: jack: Add dummy snd_jack_set_key() definition
  ...

Pull devicetree changes from Grant Likely:
 "Lots of activity in the devicetree code for v3.18.  Most of it is
  related to getting all of the overlay support code in place, but there
  are other important things in there.

  Highlights:

   - OF_RECONFIG notifiers for SPI, I2C and Platform devices.  Those
     subsystems can now respond to live changes to the device tree.

   - CONFIG_OF_OVERLAY method for applying live changes to the device
     tree

   - Removal of the of_allnodes list.  This used to be used to iterate
     over all the nodes in the device tree, but it is unnecessary
     because the same thing can be done by iterating over the list of
     child pointers.  Getting rid of of_allnodes saves some memory and
     avoids the possibility of of_allnodes being sorted differently from
     the child lists.

   - Support for retrieving original DTB blob via sysfs.  Needed by
     kexec.

   - More unittests

   - Documentation and minor bug fixes"

* tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux: (42 commits)
  of: Delete unnecessary check before calling "of_node_put()"
  of: Drop ->next pointer from struct device_node
  spi: Check for spi_of_notifier when CONFIG_OF_DYNAMIC=y
  of: support passing console options with stdout-path
  of: add optional options parameter to of_find_node_by_path()
  of: Add bindings for chosen node, stdout-path
  of: Remove unneeded and incorrect MODULE_DEVICE_TABLE
  ARM: dt: fix up PL011 device tree bindings
  of: base, fix of_property_read_string_helper kernel-doc
  of: remove select of non-existant OF_DEVICE config symbol
  spi/of: Add OF notifier handler
  spi/of: Create new device registration method and accessors
  i2c/of: Add OF_RECONFIG notifier handler
  i2c/of: Factor out Devicetree registration code
  of/overlay: Add overlay unittests
  of/overlay: Introduce DT overlay support
  of/reconfig: Add OF_DYNAMIC notifier for platform_bus_type
  of/reconfig: Always use the same structure for notifiers
  of/reconfig: Add debug output for OF_RECONFIG notifiers
  of/reconfig: Add empty stubs for the of_reconfig methods
  ...

Pull fbdev updates from Tomi Valkeinen:
 - support for mx6sl and mx6sx
 - OMAP HDMI audio rewrite to make it finally work
 - OMAP video PLL work to prepare for new DRA7xx SoCs
 - simplefb DT related improvements

* tag 'fbdev-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (81 commits)
  video: uvesafb: Deletion of an unnecessary check before the function call "platform_device_put"
  video: fbdev-VIA: Deletion of an unnecessary check before the function call "framebuffer_release"
  video: fbdev-MMP: Deletion of an unnecessary check before the function call "mmp_unregister_path"
  video: mx3fb: Deletion of an unnecessary check before the function call "backlight_device_unregister"
  video: fbdev-OMAP2: Deletion of unnecessary checks before the function call "i2c_put_adapter"
  video: fbdev-SIS: Deletion of unnecessary checks before the function call "pci_dev_put"
  video: smscufx: Deletion of unnecessary checks before the function call "vfree"
  video: udlfb: Deletion of unnecessary checks before the function call "vfree"
  video: uvesafb: Deletion of an unnecessary check before the function call "uvesafb_free"
  video: fbdev-LCDC: Deletion of an unnecessary check before the function call "vfree"
  video: fbdev: arkfb: suppress build warning
  video: fbdev: s3fb: suppress build warning
  video: fbdev: vt8623fb: suppress build warning
  OMAPDSS: hdmi5: Fix bit field for IEC958_AES2_CON_SOURCE
  OMAPDSS: hdmi: Remove __exit qualifier from hdmi_uninit_output()
  OMAPDSS: hdmi5: Change hdmi_wp idlemode to to no_idle for audio playback
  OMAPDSS: Remove all references to obsolete HDMI audio callbacks
  ASoC: omap: Remove obsolete HDMI audio code and Kconfig options
  OMAPDSS: hdmi5: Register ASoC platform device for omap hdmi audio
  OMAPDSS: hdmi5: Remove callbacks for the old ASoC DAI driver
  ...

Pull virtio updates from Michael Tsirkin:
 "virtio: virtio 1.0 support, misc patches

  This adds a lot of infrastructure for virtio 1.0 support.  Notable
  missing pieces: virtio pci, virtio balloon (needs spec extension),
  vhost scsi.

  Plus, there are some minor fixes in a couple of places.

  Note: some net drivers are affected by these patches.  David said he's
  fine with merging these patches through my tree.

  Rusty's on vacation, he acked using my tree for these, too"

* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (70 commits)
  virtio_ccw: finalize_features error handling
  virtio_ccw: future-proof finalize_features
  virtio_pci: rename virtio_pci -> virtio_pci_common
  virtio_pci: update file descriptions and copyright
  virtio_pci: split out legacy device support
  virtio_pci: setup config vector indirectly
  virtio_pci: setup vqs indirectly
  virtio_pci: delete vqs indirectly
  virtio_pci: use priv for vq notification
  virtio_pci: free up vq->priv
  virtio_pci: fix coding style for structs
  virtio_pci: add isr field
  virtio: drop legacy_only driver flag
  virtio_balloon: drop legacy_only driver flag
  virtio_ccw: rev 1 devices set VIRTIO_F_VERSION_1
  virtio: allow finalize_features to fail
  virtio_ccw: legacy: don't negotiate rev 1/features
  virtio: add API to detect legacy devices
  virtio_console: fix sparse warnings
  vhost: remove unnecessary forward declarations in vhost.h
  ...

Pull mailbox framework updates from Jassi Brar.

* 'mailbox-devel' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
  Mailbox: Add support for Platform Communication Channel
  mailbox/omap: adapt to the new mailbox framework
  mailbox: add tx_prepare client callback
  mailbox: Don't unnecessarily re-arm the polling timer

Pull spi updates from Mark Brown:
 "Not a huge amount going on this release, mainly new drivers (there's a
  couple more waiting that didn't quite make the cut for this release
  too):

   - An interface for querying if the current transfer is the last in a
     message, allowing controllers that need special handling for the
     final transfer to use the core message parsing.
   - Support for Amlogic Meson SPIFC, Imagination Technologies SFPI,
     Intel Quark X1000 and Samsung Exynos 7 controllers"

* tag 'spi-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (38 commits)
  spi/s3c64xx: Remove redundant runtime PM management
  spi: fsl-spi: remove unused variable assignment
  spi: spi-fsl-spi: Return an error code in fsl_spi_do_one_msg()
  spi: core: Do not mangle error code from kthread_run()
  spi: fsl-espi: add (un)prepare_transfer_hardware calls to save power if SPI is not in use
  spi: fsl-(e)spi: migrate to generic master queueing
  spi/txx9: Deletion of an unnecessary check before the function call "clk_disable"
  spi: cadence: Fix 3-to-8 mux mode
  spi: cadence: Init HW after reading devicetree attributes
  spi: meson: Select REGMAP_MMIO
  spi: s3c64xx: add support for exynos7 SPI controller
  spi: spi-pxa2xx: SPI support for Intel Quark X1000
  spi: meson: meson_spifc_setup_speed() can be static
  spi: spi-pxa2xx: Add helpers for regiseters' accessing
  spi: spi-mxs: Fix mapping from vmalloc-ed buffer to scatter list
  spi: atmel: introduce probe deferring
  spi: atmel: remove compat for non DT board when requesting dma chan
  spi: meson: Add support for Amlogic Meson SPIFC
  spi: meson: Add device tree bindings documentation for SPIFC
  spi: core: Add spi_transfer_is_last() helper
  ...

Pull edac updates from Mauro Carvalho Chehab:
 - Broadwell-DE support on sb-edac driver
 - Some fixes at sb-edac driver

* tag 'edac/v3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edac:
  sb_edac: Fix typo computing number of banks
  sb_edac: Add support for Broadwell-DE processor
  sb_edac: Fix discovery of top-of-low-memory for Haswell
  sb_edac: Fix erroneous bytes->gigabytes conversion
  sb_edac: Fix off-by-one error in number of channels

Currently, when trying to reuse a socket, vxlan_sock_add will grab
vn->sock_lock, locate a reusable socket, inc refcount and release
vn->sock_lock.

But vxlan_sock_release() will first decrement refcount, and then grab
that lock. refcnt operations are atomic but as currently we have
deferred works which hold vs->refcnt each, this might happen, leading to
a use after free (specially after vxlan_igmp_leave):

  CPU 1                            CPU 2

deferred work                    vxlan_sock_add
  ...                              ...
                                   spin_lock(&vn->sock_lock)
                                   vs = vxlan_find_sock();
  vxlan_sock_release
    dec vs->refcnt, reaches 0
    spin_lock(&vn->sock_lock)
                                   vxlan_sock_hold(vs), refcnt=1
                                   spin_unlock(&vn->sock_lock)
    hlist_del_rcu(&vs->hlist);
    vxlan_notify_del_rx_port(vs)
    spin_unlock(&vn->sock_lock)

So when we look for a reusable socket, we check if it wasn't freed
already before reusing it.

Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Fixes: 7c47cedf

 ("vxlan: move IGMP join/leave to work queue")
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull media updates from Mauro Carvalho Chehab:
 - Two new dvb frontend drivers: mn88472 and mn88473
 - A new driver for some PCIe DVBSky cards
 - A new remote controller driver: meson-ir
 - One LIRC staging driver got rewritten and promoted to mainstream:
   igorplugusb
 - A new tuner driver (m88rs6000t)
 - The old omap2 media driver got removed from staging.  This driver
   uses an old DMA API and it is likely broken on recent kernels.
   Nobody cared enough to fix it
 - Media bus format moved to a separate header, as DRM will also use the
   definitions there
 - mem2mem_testdev were renamed to vim2m, in order to use the same
   naming convention taken by the other virtual test driver (vivid)
 - Added a new driver for coda SoC (coda-jpeg)
 - The cx88 driver got converted to use videobuf2 core
 - Make DMABUF export buffer to work with DMA Scatter/Gather and Vmalloc
   cores
 - Lots of other fixes, improvements and cleanups on the drivers.

* tag 'media/v3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (384 commits)
  [media] mn88473: One function call less in mn88473_init() after error
  [media] mn88473: Remove uneeded check before release_firmware()
  [media] lirc_zilog: Deletion of unnecessary checks before vfree()
  [media] MAINTAINERS: Add myself as img-ir maintainer
  [media] img-ir: Don't set driver's module owner
  [media] img-ir: Depend on METAG or MIPS or COMPILE_TEST
  [media] img-ir/hw: Drop [un]register_decoder declarations
  [media] img-ir/hw: Fix potential deadlock stopping timer
  [media] img-ir/hw: Always read data to clear buffer
  [media] redrat3: ensure dma is setup properly
  [media] ddbridge: remove unneeded check before dvb_unregister_device()
  [media] si2157: One function call less in si2157_init() after error
  [media] tuners: remove uneeded checks before release_firmware()
  [media] arm: omap2: rx51-peripherals: fix build warning
  [media] stv090x: add an extra protetion against buffer overflow
  [media] stv090x: Remove an unreachable code
  [media] stv090x: Some whitespace cleanups
  [media] em28xx: checkpatch cleanup: whitespaces/new lines cleanups
  [media] si2168: add support for firmware files in new format
  [media] si2168: debug printout for firmware version
  ...