- Jul 16, 2014
-
-
Marek Szyprowski authored
This patch moves some parts of exynos4412-odroidx.dts to common exynos4412-odroid-common.dtsi file and adds support for Odroid X2 and U2/U3 boards. X2 is same as X, but it has faster SoC module (1.7GHz instead of 1.4GHz), while U2/U3 differs from X2 by different way of routing signals to host USB hub. It also lacks some hw modules not yet supported by those dts files (i.e. LCD & touch panel). Signed-off-by:
Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by:
Kukjin Kim <kgene.kim@samsung.com>
-
Marek Szyprowski authored
Last megabyte of RAM is used by secure firmware and should not be accessed by Linux kernel, so correct available memory size in DTS file. Signed-off-by:
Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by:
Kukjin Kim <kgene.kim@samsung.com>
-
Kamil Debski authored
This patch adds basic support for USB modules (host and device) on OdroidX board. Signed-off-by:
Kamil Debski <k.debski@samsung.com> [removed incorrect port@2 node] Signed-off-by:
Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by:
Kukjin Kim <kgene.kim@samsung.com>
-
Marek Szyprowski authored
This patch adds support for common hardware modules available on all Exynos4412-based Odroid boards, which already have complete support in mainline kernel. This includes secure firmware calls, watchdog, g2d and fimc (mem2mem) multimedia accelerators. Signed-off-by:
Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by:
Kukjin Kim <kgene.kim@samsung.com>
-
Marek Szyprowski authored
This patch adds port sub-nodes to exynos4 ehci and ohci modules, which are required by recently merged new exynos4 usb2 phy support. Signed-off-by:
Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by:
Kukjin Kim <kgene.kim@samsung.com>
-
Vikas Sajjan authored
The mask-tpm-reset GPIO is used by the kernel to prevent the TPM from being reset across sleep/wake. If we don't set it to anything then the TPM will be reset. U-Boot will detect this as invalid and will reset the system on resume time. This GPIO can always be low and not hurt anything. It will get pulled back high again during a normal warm reset when it will default back to an input. To properly preserve the TPM state across suspend/resume and to make the chrome U-Boot happy, properly set the GPIO to mask the reset to the TPM. Signed-off-by:
Vikas Sajjan <vikas.sajjan@samsung.com> Reviewed-by:
Doug Anderson <dianders@chromium.org> Signed-off-by:
Kukjin Kim <kgene.kim@samsung.com>
-
Doug Anderson authored
The mask-tpm-reset GPIO is used by the kernel to prevent the TPM from being reset across sleep/wake. If we don't set it to anything then the TPM will be reset. U-Boot will detect this as invalid and will reset the system on resume time. This GPIO can always be low and not hurt anything. It will get pulled back high again during a normal warm reset when it will default back to an input. To properly preserve the TPM state across suspend/resume and to make the chrome U-Boot happy, properly set the GPIO to mask the reset to the TPM. Signed-off-by:
Doug Anderson <dianders@chromium.org> Signed-off-by:
Vikas Sajjan <vikas.sajjan@samsung.com> Signed-off-by:
Kukjin Kim <kgene.kim@samsung.com>
-
- Jul 08, 2014
-
-
Tushar Behera authored
Add sound-card name property to Snow/Peach-Pit/Peach-Pi boards. Signed-off-by:
Tushar Behera <tushar.b@samsung.com> Acked-by:
Mark Brown <broonie@linaro.org> Signed-off-by:
Kukjin Kim <kgene.kim@samsung.com>
-
Andreas Faerber authored
It's 1.6 GHz for the Cortex-A15. Avoids warnings like "/cpus/cpu@0 missing clock-frequency property". Signed-off-by:
Andreas Faerber <afaerber@suse.de> Reviewed-by:
Tarek Dakhran <t.dakhran@samsung.com> Signed-off-by:
Kukjin Kim <kgene.kim@samsung.com>
-
- Jun 21, 2014
-
-
Tushar Behera authored
Peach-pit and Peach-pi boards are almost similar, hence the DTS file is also very similar. Sorting nodes in both these files will allow us to figure out the difference easily. All the node aliases are sorted in alphabetically increasing order. There is no functional change with this patch. Signed-off-by:
Tushar Behera <tushar.b@samsung.com> Reviewed-by:
Doug Anderson <dianders@chromium.org> Signed-off-by:
Kukjin Kim <kgene.kim@samsung.com>
-
Tushar Behera authored
Peach-pi board has MAX98091 audio codec connected on HSI2C-7 bus. Signed-off-by:
Tushar Behera <tushar.b@samsung.com> Reviewed-by:
Doug Anderson <dianders@chromium.org> Signed-off-by:
Kukjin Kim <kgene.kim@samsung.com>
-
- Jun 07, 2014
-
-
Nishanth Menon authored
OMAP5432, DRA75x and DRA72x have MPU DPLLs that need Duty Cycle Correction(DCC) to operate safely at frequencies >= 1.4GHz. Switch to "ti,omap5-mpu-dpll-clock" compatible property which provides this support. Signed-off-by:
Nishanth Menon <nm@ti.com> Signed-off-by:
Tero Kristo <t-kristo@ti.com>
-
- Jun 03, 2014
-
-
Jyri Sarha authored
Adds HDMI audio sDMA properties. Signed-off-by:
Jyri Sarha <jsarha@ti.com> Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ti.com> Acked-by:
Tony Lindgren <tony@atomide.com>
-
Jyri Sarha authored
Adds HDMI audio sDMA properties. Signed-off-by:
Jyri Sarha <jsarha@ti.com> Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ti.com> Acked-by:
Tony Lindgren <tony@atomide.com>
-
Florian Vaussard authored
Add the necessary DTS nodes to enable the micro-HDMI output on Parlor board. Signed-off-by:
Florian Vaussard <florian.vaussard@epfl.ch> Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ti.com> Acked-by:
Tony Lindgren <tony@atomide.com>
-
Florian Vaussard authored
Alto35 expansion board has a ZIF connector for a 3.5'' LCD. Add a common include file for this configuration, and use it on Alto35. Signed-off-by:
Florian Vaussard <florian.vaussard@epfl.ch> Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ti.com> Acked-by:
Tony Lindgren <tony@atomide.com>
-
Florian Vaussard authored
Chestnut43, Gallop43 and Palo43 expansion boards have a ZIF connector for a 4.3'' LCD. Add a common include file for this configuration, and use it on relevant expansion boards. Signed-off-by:
Florian Vaussard <florian.vaussard@epfl.ch> Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ti.com> Acked-by:
Tony Lindgren <tony@atomide.com>
-
Florian Vaussard authored
Summit and Tobi expansion boards have a HDMI connector with a TFP410 encoder. Add a common include file for this configuration, and then use it for Summit and Tobi. Signed-off-by:
Florian Vaussard <florian.vaussard@epfl.ch> Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ti.com> Acked-by:
Tony Lindgren <tony@atomide.com>
-
Tony Lindgren authored
Looks like quite a few omap3 boards have sharp ls037v7dw01 that's configured as various panel dpi entries for whatever legacy reasons. For device tree based support, let's just configure these properly for panel ls037v7dw01 instead of panel dpi. This patch creates a common file for panel ls037v7dw01, and makes boards ldp and omap3-evm to use it. The ls037v7dw01 also seems to be coupled with an ad7846 touchscreen controller for the omaps, so let's add a basic configuration for the touchscreen also using the default values. Signed-off-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ti.com>
-
Marek Belisko authored
This patch add support for lcd display on gta04 board. Display control is connected to spi (used spi bitbang driver). Signed-off-by:
Marek Belisko <marek@goldelico.com> Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ti.com> Acked-by:
Tony Lindgren <tony@atomide.com>
-
Tomi Valkeinen authored
omap5-uevm has a single HDMI output. Add the necessary display information, including pinmuxing. Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ti.com> Acked-by:
Tony Lindgren <tony@atomide.com>
-
Tomi Valkeinen authored
omap5-uevm has a tca6424a I/O expander. Add it to the .dts file. Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ti.com> Acked-by:
Tony Lindgren <tony@atomide.com>
-
Tomi Valkeinen authored
Add OMAP5 DSS nodes to omap5.dtsi. Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ti.com> Acked-by:
Tony Lindgren <tony@atomide.com>
-
Tomi Valkeinen authored
Add DT data for am43x-epos-evm's LCD panel. Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ti.com> Acked-by:
Tony Lindgren <tony@atomide.com>
-
Sathya Prakash M R authored
Add DT data for am437x-gp-evm's LCD panel. Signed-off-by:
Sathya Prakash M R <sathyap@ti.com> Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ti.com> Acked-by:
Tony Lindgren <tony@atomide.com>
-
Sathya Prakash M R authored
Add DT data for the display subsystem for AM4372. The DSS on AM4372 is basically OMAP3's DSS, without DSI and VENC blocks. Signed-off-by:
Sathya Prakash M R <sathyap@ti.com> Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ti.com> Acked-by:
Tony Lindgren <tony@atomide.com>
-
- May 31, 2014
-
-
Tushar Behera authored
Arndale-Octa board is always configured to work with trustzone firmware binary. Added DTS node entry to enable this support. Signed-off-by:
Tushar Behera <tushar.behera@linaro.org> Signed-off-by:
Kukjin Kim <kgene.kim@samsung.com>
-
Chanwoo Choi authored
This patch add pmusysreg node for Exynos3250 to access PMU (Power Management Unit) register in a centralized way using syscon driver. Signed-off-by:
Chanwoo Choi <cw00.choi@samsung.com> Acked-by:
Kyungmin Park <kyungmin.park@samsung.com> Reviewed-by:
Tomasz Figa <t.figa@samsung.com> Signed-off-by:
Kukjin Kim <kgene.kim@samsung.com>
-
Arun Kumar K authored
The vbus-supply property is wrongly updated in the usbdrd node instead of the usbdrd_phy node. This patch fixes the same. Signed-off-by:
Arun Kumar K <arun.kk@samsung.com> Signed-off-by:
Kukjin Kim <kgene.kim@samsung.com>
-
Arun Kumar K authored
The vbus-supply property is wrongly updated in the usbdrd node instead of the usbdrd_phy node. This patch fixes the same. Signed-off-by:
Arun Kumar K <arun.kk@samsung.com> Signed-off-by:
Kukjin Kim <kgene.kim@samsung.com>
-
Tarek Dakhran authored
Add initial device tree nodes for EXYNOS5410 SoC and SMDK5410 board. Signed-off-by:
Tarek Dakhran <t.dakhran@samsung.com> Signed-off-by:
Vyacheslav Tyrtov <v.tyrtov@samsung.com> Reviewed-by:
Tomasz Figa <t.figa@samsung.com> Signed-off-by:
Kukjin Kim <kgene.kim@samsung.com>
-
Tomasz Figa authored
This patch adds new exynos3250.dtsi to support Exynos3250 SoC based on Cortex-A7 dual core and includes following dt nodes: - GIC interrupt controller - Pinctrl to control GPIOs - Clock controller - CPU information (Cortex-A7 dual core) - UART to support serial port - MCT (Multi Core Timer) - ADC (Analog Digital Converter) - I2C/SPI bus - Power domain - PMU (Performance Monitoring Unit) - MSHC (Mobile Storage Host Controller) - PWM (Pluse Width Modulation) - AMBA bus - sysram node for SYSRAM memory mapping Signed-off-by:
Tomasz Figa <t.figa@samsung.com> Signed-off-by:
Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by:
Inki Dae <inki.dae@samsung.com> Signed-off-by:
Hyunhee Kim <hyunhee.kim@samsung.com> Signed-off-by:
Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by:
Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by:
Chanwoo Choi <cw00.choi@samsung.com> Cc: Ben Dooks <ben-linux@fluff.org> Cc: Kukjin Kim <kgene.kim@samsung.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: Pawel Moll <pawel.moll@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Ian Campbell <ijc+devicetree@hellion.org.uk> Cc: Kumar Gala <galak@codeaurora.org> Cc: Russell King <linux@arm.linux.org.uk> Cc: devicetree@vger.kernel.org Signed-off-by:
Kukjin Kim <kgene.kim@samsung.com>
-
Arun Kumar K authored
Adds the mfc node to exynos5800 which uses MFCv8. Signed-off-by:
Arun Kumar K <arun.kk@samsung.com> Signed-off-by:
Kukjin Kim <kgene.kim@samsung.com>
-
Vivek Gautam authored
Add required fixed-regulator for VBUS supply for USB 3.0 controller phy. Signed-off-by:
Vivek Gautam <gautam.vivek@samsung.com> Signed-off-by:
Kukjin Kim <kgene.kim@samsung.com>
-
Rahul Sharma authored
Enable FIMD for peach-pi board. Signed-off-by:
Rahul Sharma <rahul.sharma@samsung.com> Reviewed-by:
Jingoo Han <jg1.han@samsung.com> Signed-off-by:
Kukjin Kim <kgene.kim@samsung.com>
-
Rahul Sharma authored
Enable display controller with timing information for 1080p panel in Exynos5800 peach-pi board. Signed-off-by:
Rahul Sharma <rahul.sharma@samsung.com> Reviewed-by:
Jingoo Han <jg1.han@samsung.com> Signed-off-by:
Kukjin Kim <kgene.kim@samsung.com>
-
Rahul Sharma authored
Enable hdmi for peach-pi board. Signed-off-by:
Rahul Sharma <rahul.sharma@samsung.com> Acked-by:
Tomasz Figa <t.figa@samsung.com> Signed-off-by:
Kukjin Kim <kgene.kim@samsung.com>
-
Arun Kumar K authored
Adds support for google peach-pi board having the Exynos5800 SoC. Signed-off-by:
Arun Kumar K <arun.kk@samsung.com> Signed-off-by:
Doug Anderson <dianders@chromium.org> Reviewed-by:
Tomasz Figa <t.figa@samsung.com> Signed-off-by:
Kukjin Kim <kgene.kim@samsung.com>
-
Arun Kumar K authored
Most of the nodes of exynos5420 remains same for exynos5800. So the exynos5420.dtsi is included in exynos5800 and the changed node properties will be overriden. Signed-off-by:
Arun Kumar K <arun.kk@samsung.com> Reviewed-by:
Tomasz Figa <t.figa@samsung.com> Acked-by:
Olof Johansson <olof@lixom.net> Signed-off-by:
Kukjin Kim <kgene.kim@samsung.com>
-
Rahul Sharma authored
The patch adds the dts file for xyref5260 board which is based on exynos5260 SoC. Signed-off-by:
Rahul Sharma <rahul.sharma@samsung.com> Signed-off-by:
Kukjin Kim <kgene.kim@samsung.com>
-