This patch add the RGA dt config of RK3399 SoC.

Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Add a pinctrl setting to configure the cec pin to the correct function.

Signed-off-by: Pierre-Hugues Husson <phh@phh.me>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Add the HDMI CEC controller main clock coming from the CRU.

Signed-off-by: Pierre-Hugues Husson <phh@phh.me>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

The Firefly-RK3399 uses serial2 with 1,500,000 baud by default
for communication in U-Boot and in the vendor provided distros.

So let us set the same default in the Linux kernel.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Adding the linux,gpio-keymap entry also has
the side-effect of making the driver register
the touchpad as a touchpad rather than another
touchscreen.

The index for BTN_LEFT was found by trial and error.

Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Enable the graphics-related nodes on the rk3399-firefly which makes
it possible to see output on the on-board hdmi output.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Add rt5514 dsp of_node to codec list for Gru boards.

Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

RK3328 Evaluation Board use rk805 pmic, and one of the DCDCs in
rk805 is for cpu regulator, assign the cpu regulator, so the
cpufreq can work fine.

Signed-off-by: Liang Chen <cl@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Rockchip's rk3328 evaluation board has 3 mmc controllers for
sdio/sdmmc/emmc, let's enable them.

Signed-off-by: Liang Chen <cl@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Convert all RK3399 platforms to use per-lane PHY model in order to save
more power by idling unused lane(s).

Tested-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>

Haikou is a Qseven and μQseven baseboard featuring PCIe, USB3 and a
video connector for MIPI-DSI/CSI and eDP adapter.

This dts is for usage with the RK3399-Q7 SoM Puma.

Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

The RK3399-Q7 SoM is a Qseven-compatible (70mm x 70mm, MXM-230
connector) system-on-module from Theobroma Systems, featuring the
Rockchip RK3399.

It provides the following feature set:
 * up to 4GB DDR3
 * on-module SPI-NOR flash
 * on-module eMMC (with 8-bit 1.8V interface)
 * SD card (on a baseboad) via edge connector
 * Gigabit Ethernet with on-module Micrel KSZ9031 GbE PHY
 * HDMI/eDP/2x MIPI-DSI
 * 2x MIPI-CSI
 * USB
   - 1x USB 3.0 dual-role (direct connection)
   - 2x USB 3.0 host + 1x USB 2.0 (on-module USB 3.0 hub)
 * on-module STM32 Cortex-M0 companion controller, implementing:
   - low-power RTC functionality (ISL1208 emulation)
   - fan controller (AMC6821 emulation)
   - USB<->CAN bridge controller

Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

The ROCK64 is a credit card size 4K60P HDR Media Board Computer using the
Rockchip RK3328 Quad-Core ARM Cortex A53 64-Bit Processor and supporting
up to 4GB 1600MHz LPDDR3 memory. It provides eMMC module socket, MicroSD
Card slot, Pi-2 Bus, Pi-P5+ Bus, USB 3.0 and many others peripheral
devices interface for makers to integrate with sensors and devices.

The devicetree currently supports basic peripherals, with more to be
added later on.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>

This patch add pdm controller device node for rk3328.

Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Add VPU/VDEC/IEP/ISP0/ISP1 iommu nodes

Signed-off-by: Simon Xue <xxm@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Add IEP/ISP/VOP/HEVC/VPU iommu nodes

Signed-off-by: Simon Xue <xxm@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Add H265e/VEPU/VPU/VDEC/VOP iommu nodes

Signed-off-by: Simon Xue <xxm@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

This adds and enable the operating points that have been tested and are
currently supported by the SoC. This also adds clocks for ARMCLKL and
ARMCLKB.

Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

RK805 consists of 4 DCDCs, 3 LDOs. It's different from RK808
and RK818 that there are 2 output only GPIOs, we should add
properties "gpio-controller" and "gpio-cells = <2>".

Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Currently we are assigning mic irq to rt5514 i2c driver, which is wrong.
Assign it to rt5514 spi driver instead.

Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

We need to init vop aclk and hclk incase the U-Boot does not do
the initialize.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

There are 4 pwm channels built in rk3328 soc, need to configure
the both APB clock and bus clock.

Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

According to rt5514 dt-binding, it should be "realtek,dmic-init-delay-ms".

Fixes: 48f4d979

 (arm64: dts: rockchip: add Gru/Kevin DTS)
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

RK3399 USB DWC3 controller has a issue that FS/LS devices not
recognized if inserted through USB 3.0 HUB. It's because that
the inter-packet delay between the SSPLIT token to SETUP token
is about 566ns, more then the USB spec requirement.

This patch adds a quirk "snps,dis-tx-ipgap-linecheck-quirk" to
disable the u2mac linestate check to decrease the SSPLIT token
to SETUP token inter-packet delay from 566ns to 466ns.

Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

When adding the rk3399 sapphire som, two more of the recently removed
num-slots properties of dw-mmc nodes slipped in.
Remove them again.

Fixes: 8164a84c

 ("arm64: dts: rockchip: Add support for rk3399 sapphire SOM")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Enable the gmac2phy, make the gmac2phy work on
the rk3328-evb board.

Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The gmac2phy controller of rk3328 is connected to integrated PHY
directly inside, add the node for the integrated PHY support.

Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

enable tsadc module on RK3328 eavluation board

Signed-off-by: Rocky Hao <rocky.hao@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

add thermal zone and dynamic CPU power coefficients for rk3328

Signed-off-by: Rocky Hao <rocky.hao@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

add tsadc needed main information for rk3328 SoC.
50000Hz is the max clock rate supported by tsadc module.

Signed-off-by: Rocky Hao <rocky.hao@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

This patch add the i2s dt nodes for rk3328.

Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Add support for the rk3399 excavator main board.
This board works in a combination with the sapphire SOM.

This board have been sold as the rk3399 evaluation board for commercial customers.
You can get more info from below link:
http://opensource.rock-chips.com/wiki_Excavator_sapphire_board



Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Add support for the rk3399 sapphire SOM board.
This board works in a combination with the excavator main board.

You can get more info from below link:
http://opensource.rock-chips.com/wiki_Excavator_sapphire_board



Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Add an hdmi node, and also add hdmi endpoints to vopb and vopl
output port nodes.

Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Add an mipi node, and also add mipi endpoints to vopb and vopl
output port nodes.

Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Add an edp node, and also add edp endpoints to vopb and vopl
output port nodes.

Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

1. add pd node for RK3399 Soc
2. create power domain tree
3. add qos node for domain

Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Add devicetree nodes for rk3399 VOP (Video Output Processors), and the
top level display-subsystem root node.

Later patches add endpoints (eDP, HDMI, MIPI, etc) that attach to the
VOPs' output ports.

Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Add opp tables for cpu cluster0 and cluster1 by including
rk3399-opp.dtsi.

Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

This patch adds basic OPP entries for RK3328 SoC.

Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>