Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2015-06-26

This series contains fixes for igb, e1000e and i40evf.

Todd disables IPv6 extension header processing due to a hardware errata
and bumps the driver version.

Yanir provides six fixes for e1000e.  First is a fix for a locking issue
where we were not always taking the pci_bus_sem semaphore all the time
when calling pci_disable_link_state_locked(), so fix the code to only call
pci_disable_link_state_locked() when the semaphore has been acquired,
otherwise call pci_disable_link_state().  A previous fix for i219 where
the hardware prevented ULP entry caused EEE in Sx not the be enabled, so
modify the code flow that allows both ULP and EEE in Sx.  Fix an issue
when running 10/100 full duplex on i219 where CRC errors were occurring
by increasing the IPG from 8 to 0xC as per the hardware developers.
Fix a data corruption issue found on some platforms by increasing the
minimum gap between the PHY FIFO read and write pointers.  Fix i219,
which does not require the K1 workaround for LPT devices.

Mitch provides a i40evf fix for a panic when changing MTU.  Down was
requesting queue disables, but then exited immediately without waiting
for the queues to actually be disabled.  This could allow any function
called after i40evf_down() to run immediately, including i40evf_up(),
and causes a memory leak.  Fixed the issue by removing the whole
reinit_locked function which allows for the driver to handle the state
changes by requesting reset from the periodic timer.  The second fix
resolves an issue where RSS was being configured as though it is using
the maximum number of queue.  This can cause the device to drop a lot
of receive traffic, as the packets get assigned to non-functional queues.
This is resolved by only configuring RSS with the number of active queues.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

As some C45 10G PHYs(e.g. Cortina CS4315/CS4340 PHY) have
zero Devices In package, current driver can't get correct
devices_in_package value by non-zero Devices In package.
so let's probe more with zero Devices In package to support
more C45 PHYs.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michel reported following lockdep splat

[   44.718117] INFO: trying to register non-static key.
[   44.723081] the code is fine but needs lockdep annotation.
[   44.728559] turning off the locking correctness validator.
[   44.734036] CPU: 8 PID: 5483 Comm: ethtool Not tainted 4.1.0
[   44.770289] Call Trace:
[   44.772741]  [<ffffffff816eb1cd>] dump_stack+0x4c/0x65
[   44.777879]  [<ffffffff8111d921>] ? console_unlock+0x1f1/0x510
[   44.783708]  [<ffffffff811121f5>] __lock_acquire+0x1d05/0x1f10
[   44.789538]  [<ffffffff8111370a>] ? mark_held_locks+0x6a/0x90
[   44.795276]  [<ffffffff81113835>] ? trace_hardirqs_on_caller+0x105/0x1d0
[   44.801967]  [<ffffffff8111390d>] ? trace_hardirqs_on+0xd/0x10
[   44.807793]  [<ffffffff811330fa>] ? hrtimer_try_to_cancel+0x4a/0x250
[   44.814142]  [<ffffffff81112ba6>] lock_acquire+0xb6/0x290
[   44.819537]  [<ffffffff810d6675>] ? flush_work+0x5/0x280
[   44.824844]  [<ffffffff810d66ad>] flush_work+0x3d/0x280
[   44.830061]  [<ffffffff810d6675>] ? flush_work+0x5/0x280
[   44.835366]  [<ffffffff816f3c43>] ? schedule_hrtimeout_range+0x13/0x20
[   44.841889]  [<ffffffff8112ec9b>] ? usleep_range+0x4b/0x50
[   44.847365]  [<ffffffff8111370a>] ? mark_held_locks+0x6a/0x90
[   44.853102]  [<ffffffff810d8585>] ? __cancel_work_timer+0x105/0x1c0
[   44.859359]  [<ffffffff81113835>] ? trace_hardirqs_on_caller+0x105/0x1d0
[   44.866045]  [<ffffffff810d851f>] __cancel_work_timer+0x9f/0x1c0
[   44.872048]  [<ffffffffa0010982>] ? bnx2x_func_stop+0x42/0x90 [bnx2x]
[   44.878481]  [<ffffffff810d8670>] cancel_work_sync+0x10/0x20
[   44.884134]  [<ffffffffa00259e5>] bnx2x_chip_cleanup+0x245/0x730 [bnx2x]
[   44.890829]  [<ffffffff8110ce02>] ? up+0x32/0x50
[   44.895439]  [<ffffffff811306b5>] ? del_timer_sync+0x5/0xd0
[   44.901005]  [<ffffffffa005596d>] bnx2x_nic_unload+0x20d/0x8e0 [bnx2x]
[   44.907527]  [<ffffffff811f1aef>] ? might_fault+0x5f/0xb0
[   44.912921]  [<ffffffffa005851c>] bnx2x_reload_if_running+0x2c/0x50 [bnx2x]
[   44.919879]  [<ffffffffa005a3c5>] bnx2x_set_ringparam+0x2b5/0x460 [bnx2x]
[   44.926664]  [<ffffffff815d498b>] dev_ethtool+0x55b/0x1c40
[   44.932148]  [<ffffffff815dfdc7>] ? rtnl_lock+0x17/0x20
[   44.937364]  [<ffffffff815e7f8b>] dev_ioctl+0x17b/0x630
[   44.942582]  [<ffffffff815abf8d>] sock_do_ioctl+0x5d/0x70
[   44.947972]  [<ffffffff815ac013>] sock_ioctl+0x73/0x280
[   44.953192]  [<ffffffff8124c1c8>] do_vfs_ioctl+0x88/0x5b0
[   44.958587]  [<ffffffff8110d0b3>] ? up_read+0x23/0x40
[   44.963631]  [<ffffffff812584cc>] ? __fget_light+0x6c/0xa0
[   44.969105]  [<ffffffff8124c781>] SyS_ioctl+0x91/0xb0
[   44.974149]  [<ffffffff816f4dd7>] system_call_fastpath+0x12/0x6f

As bnx2x_init_ptp() is only called if bp->flags contains PTP_SUPPORTED,
we also need to guard bnx2x_stop_ptp() with same condition, otherwise
ptp_task workqueue is not initialized and kernel barfs on
cancel_work_sync()

Fixes: eeed018c

 ("bnx2x: Add timestamping and PTP hardware clock support")
Reported-by: Michel Lespinasse <walken@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Michal Kalderon <Michal.Kalderon@qlogic.com>
Cc: Ariel Elior <Ariel.Elior@qlogic.com>
Cc: Yuval Mintz <Yuval.Mintz@qlogic.com>
Cc: David Decotigny <decot@google.com>
Acked-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Not all silicon implementations of the Freescale FEC hardware module
have the RACC (Receive Accelerator Function) register, so we should not
be trying to access it on those that don't. Currently none of the ColdFire
based parts with a FEC have it.

Support for RACC was introduced by commit 4c09eed9 ("net: fec: Enable imx6
enet checksum acceleration"). A fix was introduced in commit d1391930


("net: fec: Fix build for MCF5272") that disables its use on the ColdFire
M5272 part, but it doesn't fix the general case of other ColdFire parts.

To fix we create a quirk flag, FEC_QUIRK_HAS_RACC, and check it before
working with the RACC register.

Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

When limiting phy link speed using "max-speed" to 100mbps or less on a
giga bit phy, phy never completes auto negotiation and phy state
machine is held in PHY_AN. Fixing this issue by comparing the giga
bit advertise though phydev->supported doesn't have it but phy has
BMSR_ESTATEN set. So that auto negotiation is restarted as old and
new advertise are different and link comes up fine.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

DSA master netdev promiscuity counter was not being properly
decremented on slave device open error path.

Signed-off-by: Gilad Ben-Yossef <gilad@benyossef.com>
CC: Gilad Ben-Yossef <giladb@ezchip.com>
CC: David S. Miller <davem@davemloft.net>
CC: Florian Fainelli <f.fainelli@gmail.com>
CC: Guenter Roeck <linux@roeck-us.net>
CC: Andrew Lunn <andrew@lunn.ch>
CC: Scott Feldman <sfeldma@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

David Miller says:

====================
Get rid of sock->sk_protinfo.

These two patches get rid of the last remaining user of sk_protinfo
(ax25) and then really gets rid of the struct member.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

No more users, so it can now be removed.

Signed-off-by: David S. Miller <davem@davemloft.net>

Just make a ax25_sock structure that provides the ax25_cb pointer.

Signed-off-by: David S. Miller <davem@davemloft.net>

If CONFIG_ACPI=n:

    drivers/net/ethernet/apm/xgene/xgene_enet_main.c: In function ‘xgene_enet_get_resources’:
    drivers/net/ethernet/apm/xgene/xgene_enet_main.c:951: warning: ‘ret’ may be used uninitialized in this function

If the driver is bound to a legacy platform device, ret will contain
arbitrary data. If it is non-zero, it will be returned to the caller as
an error code.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/core/flow_dissector.c: In function ‘__skb_flow_dissect’:
net/core/flow_dissector.c:132: warning: ‘ip_proto’ may be used uninitialized in this function

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function netif_set_real_num_tx_queues() will return -EINVAL if
the second parameter < 1, so call this function with the second
parameter set to 0 is meaningless.

Signed-off-by: Liang Li <liang.z.li@intel.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The following lockdep splat was seen due to the wrong context for
grabbing in_dev.

===============================
[ INFO: suspicious RCU usage. ]
4.1.0-next-20150626-dbg-00020-g54a6d91-dirty #244 Not tainted
-------------------------------
include/linux/inetdevice.h:205 suspicious rcu_dereference_check() usage!

other info that might help us debug this:

rcu_scheduler_active = 1, debug_locks = 0
2 locks held by ip/403:
 #0:  (rtnl_mutex){+.+.+.}, at: [<ffffffff81453305>] rtnl_lock+0x17/0x19
 #1:  ((inetaddr_chain).rwsem){.+.+.+}, at: [<ffffffff8105c327>] __blocking_notifier_call_chain+0x35/0x6a

stack backtrace:
CPU: 2 PID: 403 Comm: ip Not tainted 4.1.0-next-20150626-dbg-00020-g54a6d91-dirty #244
 0000000000000001 ffff8800b189b728 ffffffff8150a542 ffffffff8107a8b3
 ffff880037bbea40 ffff8800b189b758 ffffffff8107cb74 ffff8800379dbd00
 ffff8800bec85800 ffff8800bf9e13c0 00000000000000ff ffff8800b189b7d8
Call Trace:
 [<ffffffff8150a542>] dump_stack+0x4c/0x6e
 [<ffffffff8107a8b3>] ? up+0x39/0x3e
 [<ffffffff8107cb74>] lockdep_rcu_suspicious+0xf7/0x100
 [<ffffffff814b63c3>] fib_dump_info+0x227/0x3e2
 [<ffffffff814b6624>] rtmsg_fib+0xa6/0x116
 [<ffffffff814b978f>] fib_table_insert+0x316/0x355
 [<ffffffff814b362e>] fib_magic+0xb7/0xc7
 [<ffffffff814b4803>] fib_add_ifaddr+0xb1/0x13b
 [<ffffffff814b4d09>] fib_inetaddr_event+0x36/0x90
 [<ffffffff8105c086>] notifier_call_chain+0x4c/0x71
 [<ffffffff8105c340>] __blocking_notifier_call_chain+0x4e/0x6a
 [<ffffffff8105c370>] blocking_notifier_call_chain+0x14/0x16
 [<ffffffff814a7f50>] __inet_insert_ifa+0x1a5/0x1b3
 [<ffffffff814a894d>] inet_rtm_newaddr+0x350/0x35f
 [<ffffffff81457866>] rtnetlink_rcv_msg+0x17b/0x18a
 [<ffffffff8107e7c3>] ? trace_hardirqs_on+0xd/0xf
 [<ffffffff8146965f>] ? netlink_deliver_tap+0x1cb/0x1f7
 [<ffffffff814576eb>] ? rtnl_newlink+0x72a/0x72a
...

This patch resolves that splat.

Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Reported-by: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit 1f66d161


("tipc: introduce starvation free send algorithm")
we introduced a counter per priority level for buffers
in the link backlog queue. We also introduced a new
function tipc_link_purge_backlog(), to reset these
counters to zero when the link is reset.

Unfortunately, we missed to call this function when
the broadcast link is reset, with the result that the
values of these counters might be permanently skewed
when new nodes are attached. This may in the worst case
lead to permananent, but spurious, broadcast link
congestion, where no broadcast packets can be sent at
all.

We fix this bug with this commit.

Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver will only configure as many queues as there are available
CPUs, up the maximum number of queues. However, it always configures
RSS as though it is using the maximum number of queues. This can cause
the device to drop a lot of RX traffic, as the packets get assigned to
nonfunctional queues.

Fix this by only configuring RSS with the number of active queues.

Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Down was requesting queue disables, but then exited immediately
without waiting for the queues to actually disable.  This could
allow any function called after i40evf_down to run immediately,
including i40evf_up, and causes a memory leak.

Removing the whole reinit_locked function is the best way
to go about this, and allows for the driver to handle the
state changes by requesting reset from the periodic timer.

Also, add a couple WARN_ONs in slow path to help us recognize
if we re-introduce this issue or missed any cases.

Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

In SPT hardware does not require this driver workaround.
Removed the conditional that caused K1 workaround execution on SPT.

Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Due to clocking changes in the Skylake platform, there was i219
data corruption. To work around this, HW team reported the need
to increase the minimum gap between the PHY FIFO read and write pointers.

Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

In SPT/i219, there were CRC errors in speed 10/100 full duplex.
The solution given by the HW team is to increase the IPG from 8 to 0xC

Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

In i219, there is a hardware bug that prevented ULP entry.
A side effect of the original software fix for this was that EEE in
Sx couldn't be enabled.
This patch implements a modified flow that allows both ULP and EEE in Sx.

Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

On power up, the MAC - PHY interface needs to be set to PCIe, even if
cable is disconnected.  In ME systems, the ME handles this on exit from
Sx state. In non-ME, the driver handles it. Added a check for non-ME
system to the driver code that handles that.

Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e_disable_aspm called pci_disable_link_state_locked which requires
pci_bus_sem to be held, but is also called from places where this semaphore
was not previously acquired. This patch implements two flavors of
disable_aspm, one that acquires the lock, and the other (_locked) which
should be called when the semaphore is already acquired.

Signed-off-by: Yanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Bump version of igb to igb-5.2.18

Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Disable IPv6 extension header processing as per hardware errata.

Also fix copyright date.

Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Yuval Mintz says:

====================
bnx2x: various fixes

This patch series contains several small fixes [with the possible
exception of the first 2 link fixes] for various driver flows.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Due to FW constraints, driver must make sure that transmitted SKBs will
not be too fragmented, or in the case that they are - that each 'window'
of fragments passed to the FW would contain at least an mss worth of data.

For encapsultaed packets the calculation is wrong, since it ignores the
inner headers in the calculation of the headers' length.
This could lead to a FW assertion in case of a too-fragmented encapsulated
packet.

Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

During an error flow when trying to access the nvram the driver doesn't
release the hw lock it acquired.

Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since driver statistics flow access MACs and those might reset during
link re-configurations, when we're about to change link properties we
have to make sure that statistics are not operational.
Statisics would be re-enabled [i.e., gathering of statistics would
re-commence] once physical link is achieved again.

Since driver employs a link-flap avoidance scheme, there are scenarios
where driver will receive no indication that the new link is up, and
as a result the statistics would not be re-enabled.

Preventing LFA from working in such cases would guarantee that we'll
always receive such indications and thus will fix statistics gathering.

Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

20g-capable devices are not configured properly for self-test, using
10g as their speed which cause the link indication to remain down and
fail the internal loopback test.

Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There's a bug in today's driver where VF requests to add/remove MAC filters
always reach the Hypervisor as add requests.
This prevents the VF from changing its MAC address, as it cannot remove the
previously configured MAC and runs out of MAC credits.

Signed-off-by: Shahed Shaikh <Shahed.Shaikh@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The scratchpad is a shared block between all functions of a given device.
Due to HW limitations, we can't properly close its parity notifications
to all functions on legal flows.
E.g., it's possible that while taking a register dump from one function
a parity error would be triggered on other functions.

Today driver doesn't consider this parity as a 'real' parity unless its
being accompanied by additional indications [which would happen in a real
parity scenario]; But it does print notifications for such events in the
system logs.

This eliminates such prints - in case of real parities driver would have
additional indications; But if this is the only signal user will not even
see a parity being logged in the system.

Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Each time a flow finishes reads from the classification shadow
configuration in the driver, that flow would check for pending commands
and pass them to FW if possible.
In case there's already a completion pending command, I.e., a ramrod
that has been sent to the FW and is yet to be completed while said flow
tries to configure the pending command we would get a false error message
in logs [and panic if SOE was used for driver compilation] since the
command could not have been completed.

This prevents said print [and panic]; The pending command will be sent by
the time the completion of the current sent command would arrive.

Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ethtool shows KR supported/advertised speeds incorrectly as baseT
in cases the board is in fact KR-base.

Signed-off-by: Yaniv Rosner <Yaniv.Rosner@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This fixes several issues relating to asymmetric configuration:
 1. When user requests to disable TX, the local-device needs to
    advertise both PAUSE and ASM_DIR, but to avoid transmitting pause
    frames. In the 578xx, it would ignore the TX disable.

 2. When user advertises RX-only, ASM_DIR was advertised instead of
    PAUSE/ASM_DIR.

 3. When changing mode, the advertised PAUSE/ASM_DIR was not cleared
    before setting new one, so disabling RX or TX had no impact on the
    'advertised' as appeared in the 'ethtool -a' output.

Signed-off-by: Yaniv Rosner <Yaniv.Rosner@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix typo in the validation rules for flower's attributes

Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We use spinlock to access a single flag. We can avoid spin_locks by using
atomic variable and atomic_cmpxchg(). Use atomic_cmpxchg to set the flag
for idle to poll. And a simple atomic_set to unlock (set idle from poll).

In napi poll, if gro is enabled, we call napi_gro_receive() to deliver the
packets. Before we call napi_complete(), i.e while re-polling, if low
latency busy poll is called, we use netif_receive_skb() to deliver the packets.
At this point if there are some skb's held in GRO, busy poll could deliver the
packets out of order. So we call napi_gro_flush() to flush skbs before we
move the napi poll to idle.

Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vitesse VSC8641 is compatible with Vitesse 82xx

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

CONFIG_GIANFAR is not depended on FSL_SOC, it
can be built on non-PPC platforms.

Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There was a missing assignment so the "if (ret)" on the next line is
never true.

Fixes: f21fb3ed

 ('Add support of Cavium Liquidio ethernet adapters')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We need to unlock before returning here.

Fixes: a0d2f206

 ('Renesas Ethernet AVB PTP clock driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>