When port-to-port forwarding for interfaces in HSR node is enabled,
disable promiscuous mode since L2 frame forward happens at the
offloaded hardware.

Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230614114710.31400-1-r-gunasekaran@ti.com


Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Christian Marangi says:

====================
leds: trigger: netdev: add additional modes

This is a continue of [1]. It was decided to take a more gradual
approach to implement LEDs support for switch and phy starting with
basic support and then implementing the hw control part when we have all
the prereq done.

This should be the final part for the netdev trigger.
I added net-next tag and added netdev mailing list since I was informed
that this should be merged with netdev branch.

We collect some info around and we found a good set of modes that are
common in almost all the PHY and Switch.

These modes are:
- Modes for dedicated link speed(10, 100, 1000 mbps). Additional mode
  can be added later following this example.
- Modes for half and full duplex.

The original idea was to add hw control only modes.
While the concept makes sense in practice it would results in lots of
additional code and extra check to make sure we are setting correct modes.

With the suggestion from Andrew it was pointed out that using the ethtool
APIs we can actually get the current link speed and duplex and this
effectively removed the problem of having hw control only modes since we
can fallback to software.

Since these modes are supported by software, we can skip providing an
user for this in the LED driver to support hw control for these new modes
(that will come right after this is merged) and prevent this to be another
multi subsystem series.

For link speed and duplex we use ethtool APIs.

To call ethtool APIs, rtnl lock is needed but this can be skipped on
handling netdev events as the lock is already held.

[1] https://lore.kernel.org/lkml/20230216013230.22978-1-ansuelsmth@gmail.com/
====================

Link: https://lore.kernel.org/r/20230619204700.6665-1-ansuelsmth@gmail.com


Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Expose hw_control status via sysfs for the netdev trigger to give
userspace better understanding of the current state of the trigger and
the LED.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Acked-by: Lee Jones <lee@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add additional modes for specific link duplex. Use ethtool APIs to get the
current link duplex and enable the LED accordingly. Under netdev event
handler the rtnl lock is already held and is not needed to be set to
access ethtool APIs.

This is especially useful for PHY and Switch that supports LEDs hw
control for specific link duplex.

Add additional modes:
- half_duplex: Turn on LED when link is half duplex
- full_duplex: Turn on LED when link is full duplex

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Lee Jones <lee@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add additional modes for specific link speed. Use ethtool APIs to get the
current link speed and enable the LED accordingly. Under netdev event
handler the rtnl lock is already held and is not needed to be set to
access ethtool APIs.

This is especially useful for PHY and Switch that supports LEDs hw
control for specific link speed. (example scenario a PHY that have 2 LED
connected one green and one orange where the green is turned on with
1000mbps speed and orange is turned on with 10mpbs speed)

On mode set from sysfs we check if we have enabled split link speed mode
and reject enabling generic link mode to prevent wrong and redundant
configuration.

Rework logic on the set baseline state to support these new modes to
select if we need to turn on or off the LED.

Add additional modes:
- link_10: Turn on LED when link speed is 10mbps
- link_100: Turn on LED when link speed is 100mbps
- link_1000: Turn on LED when link speed is 1000mbps

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Lee Jones <lee@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Link VF representors to parent PCI device to benefit from
systemd defined naming scheme.

Without this change the representor is visible as ethN.

Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20230620144855.288443-1-ivecera@redhat.com


Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Petr Machata says:

====================
selftests: Preparations for out-of-order-operations patches in mlxsw

The mlxsw driver currently makes the assumption that the user applies
configuration in a bottom-up manner. Thus netdevices need to be added to
the bridge before IP addresses are configured on that bridge or SVI added
on top of it. Enslaving a netdevice to another netdevice that already has
uppers is in fact forbidden by mlxsw for this reason. Despite this safety,
it is rather easy to get into situations where the offloaded configuration
is just plain wrong.

Over the course of the following several patchsets, mlxsw code is going to
be adjusted to diminish the space of wrongly offloaded configurations.
Ideally the offload state will reflect the actual state, regardless of the
sequence of operation used to construct that state.

Several selftests build configurations that will not be offloadable in the
future on some systems. The reason is that what will get offloaded is the
actual configuration, not the configuration steps.

For example, when a port is added to a bridge that has an IP address, that
bridge will get a RIF, which it would not have with the current code. But
on Nvidia Spectrum-1 machines, MAC addresses of all RIFs need to have the
same prefix, which the bridge will violate. The RIF thus couldn't be
created, and the enslavement is therefore canceled, because it would lead
to an unoffloadable configuration. This breaks some selftests.

In this patchset, adjust selftests to avoid the configurations that mlxsw
would be incapable of offloading, while maintaining relevance with regards
to the feature that is being tested. There are generally two cases of
fixes:

- Disabling IPv6 autogen on bridges that do not participate in routing,
  either because of the abovementioned requirement to keep the same MAC
  prefix on all in-HW router interfaces, or, on 802.1ad bridges, because
  in-HW router interfaces are not supported at all.

- Setting the bridge MAC address to what it will become after the first
  member port is attached, so that the in-HW router interface is created
  with a supported MAC address.

The patchset is then split thus:

- Patches #1-#7 adjust generic selftests
- Patches #8-#16 adjust mlxsw-specific selftests
====================

Link: https://lore.kernel.org/r/cover.1687265905.git.petrm@nvidia.com


Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In a future patch, mlxsw will start adding RIFs to uppers of front panel
port netdevices, if they have an IP address.

At the time that the front panel port is enslaved to the bridge, the bridge
MAC address does not have the same prefix as other interfaces in the
system. On Nvidia Spectrum-1 machines all the RIFs have to have the same
38-bit MAC address prefix. Since the bridge does not obey this limitation,
the RIF cannot be created, and the enslavement attempt is vetoed on the
grounds of the configuration not being offloadable.

The bridge eventually inherits MAC address from its first member, after the
enslavement is acked. A number of (mainly VXLAN) selftests already work
around the problem by setting the MAC address to whatever it will
eventually be anyway. Do the same for this selftest.

Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In a future patch, mlxsw will start adding RIFs to uppers of front panel
port netdevices, if they have an IP address.

At the time that the front panel port is enslaved to the bridge (this holds
for all bridges used here), the bridge MAC address does not have the same
prefix as other interfaces in the system. On Nvidia Spectrum-1 machines all
the RIFs have to have the same 38-bit MAC address prefix. Since the bridge
does not obey this limitation, the RIF cannot be created, and the
enslavement attempt is vetoed on the grounds of the configuration not being
offloadable.

The selftest itself however checks various aspects of VXLAN offloading and
the bridges do not need to participate in routing traffic. The IP addresses
or the RIFs are irrelevant.

Fix by disabling automatic IPv6 address generation for the HW-offloaded
bridges in this selftest, thus exempting them from mlxsw router attention.

Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In a future patch, mlxsw will start adding RIFs to uppers of front panel
port netdevices, if they have an IP address.

At the time that the front panel port is enslaved to the bridge, the bridge
MAC address does not have the same prefix as other interfaces in the
system. On Nvidia Spectrum-1 machines all the RIFs have to have the same
38-bit MAC address prefix. Since the bridge does not obey this limitation,
the RIF cannot be created, and the enslavement attempt is vetoed on the
grounds of the configuration not being offloadable.

The selftest itself however checks vetoing of a different aspect of the
configuration and the bridge does not need to participate in routing
traffic. The IP address or the RIF are irrelevant.

Fix by disabling automatic IPv6 address generation for the HW-offloaded
bridge in this selftest, thus exempting it from mlxsw router attention.

Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In a future patch, mlxsw will start adding RIFs to uppers of front panel
port netdevices, if they have an IP address.

At the time that the front panel port is enslaved to the bridge (this holds
for both bridges used here), the bridge MAC address does not have the same
prefix as other interfaces in the system. On Nvidia Spectrum-1 machines all
the RIFs have to have the same 38-bit MAC address prefix. Since the bridge
does not obey this limitation, the RIF cannot be created, and the
enslavement attempt is vetoed on the grounds of the configuration not being
offloadable.

The selftest itself however checks traffic prioritization and scheduling,
and the bridges serve for their L2 forwarding capabilities, and do not need
to participate in routing traffic. The IP addresses or the RIFs are
irrelevant.

Fix by disabling automatic IPv6 address generation for the HW-offloaded
bridges in this selftest, thus exempting them from mlxsw router attention.

Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In a future patch, mlxsw will start adding RIFs to uppers of front panel
port netdevices, if they have an IP address.

At the time that the front panel port is enslaved to the bridge (this holds
for both bridges used here), the bridge MAC address does not have the same
prefix as other interfaces in the system. On Nvidia Spectrum-1 machines all
the RIFs have to have the same 38-bit MAC address prefix. Since the bridge
does not obey this limitation, the RIF cannot be created, and the
enslavement attempt is vetoed on the grounds of the configuration not being
offloadable.

The selftest itself however checks traffic prioritization and scheduling,
and the bridges serve for their L2 forwarding capabilities, and do not need
to participate in routing traffic. The IP addresses or the RIFs are
irrelevant.

Fix by disabling automatic IPv6 address generation for the HW-offloaded
bridges in this selftest, thus exempting them from mlxsw router attention.

Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In a future patch, mlxsw will start adding RIFs to uppers of front panel
port netdevices, if they have an IP address.

At the time that the front panel port is enslaved to the bridge, the bridge
MAC address does not have the same prefix as other interfaces in the
system. On Nvidia Spectrum-1 machines all the RIFs have to have the same
38-bit MAC address prefix. Since the bridge does not obey this limitation,
the RIF cannot be created, and the enslavement attempt is vetoed on the
grounds of the configuration not being offloadable.

The selftest itself however checks DCB DSCP-based prioritization, and the
bridge serves for its L2 forwarding capabilities, and does not need to
participate in routing traffic. The IP address or the RIF are irrelevant.

Fix by disabling automatic IPv6 address generation for the HW-offloaded
bridge in this selftest, thus exempting it from mlxsw router attention.

Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In a future patch, mlxsw will start adding RIFs to uppers of front panel
port netdevices, if they have an IP address.

At the time that the front panel port is enslaved to the bridge, the bridge
MAC address does not have the same prefix as other interfaces in the
system. On Nvidia Spectrum-1 machines all the RIFs have to have the same
38-bit MAC address prefix. Since the bridge does not obey this limitation,
the RIF cannot be created, and the enslavement attempt is vetoed on the
grounds of the configuration not being offloadable.

The selftest itself however checks how many mirroring sessions a machine is
capable of offloading. The IP address or the RIF are irrelevant.

Fix by disabling automatic IPv6 address generation for the HW-offloaded
bridge in this selftest, thus exempting it from mlxsw router attention.

Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In a future patch, mlxsw will start adding RIFs to uppers of front panel
port netdevices, if they have an IP address.

At the time that the front panel port is enslaved to the bridge (this holds
for all bridges used here), the bridge MAC address does not have the same
prefix as other interfaces in the system. On Nvidia Spectrum-1 machines all
the RIFs have to have the same 38-bit MAC address prefix. Since the bridge
does not obey this limitation, the RIF cannot be created, and the
enslavement attempt is vetoed on the grounds of the configuration not being
offloadable.

The selftest itself however checks whether a different vetoed aspect of the
configuration provides an extack. The IP address or the RIF are irrelevant.

Fix by disabling automatic IPv6 address generation for the HW-offloaded
bridges in this selftest, thus exempting them from mlxsw router attention.

Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In a future patch, mlxsw will start adding RIFs to uppers of front panel
port netdevices, if they have an IP address.

The swp enslavement to the 802.1ad bridge is not allowed, because RIFs are
not allowed to be created for 802.1ad bridges, but the address indicates
one needs to be created. Thus the veto selftests fail already during the
port enslavement. Then the attempt to create a VLAN on top of the same
bridge is not vetoed, because the bridge is not related to mlxsw, and the
selftest fails.

Fix by disabling automatic IPv6 address generation for the bridges in this
selftest, thus exempting them from the mlxsw router attention.

Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In a future patch, mlxsw will start adding RIFs to uppers of front panel
port netdevices, if they have an IP address.

At the time that the front panel port is enslaved to the bridge, the bridge
MAC address does not have the same prefix as other interfaces in the
system. On Nvidia Spectrum-1 machines all the RIFs have to have the same
38-bit MAC address prefix. Since the bridge does not obey this limitation,
the RIF cannot be created, and the enslavement attempt is vetoed on the
grounds of the configuration not being offloadable.

The bridge eventually inherits MAC address from its first member, after the
enslavement is acked. A number of (mainly VXLAN) selftests already work
around the problem by setting the MAC address to whatever it will
eventually be anyway. Do the same here.

Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In a future patch, mlxsw will start adding RIFs to uppers of front panel
port netdevices, if they have an IP address.

At the time that the front panel port is enslaved to the bridge, the bridge
MAC address does not have the same prefix as other interfaces in the
system. On Nvidia Spectrum-1 machines all the RIFs have to have the same
38-bit MAC address prefix. Since the bridge does not obey this limitation,
the RIF cannot be created, and the enslavement attempt is vetoed on the
grounds of the configuration not being offloadable.

The bridge eventually inherits MAC address from its first member, after the
enslavement is acked. A number of (mainly VXLAN) selftests already work
around the problem by setting the MAC address to whatever it will
eventually be anyway. Do the same for several mirror_gre selftests.

Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In a future patch, mlxsw will start adding RIFs to uppers of front panel
port netdevices, if they have an IP address.

At the time that the front panel port is enslaved to the bridge, the bridge
MAC address does not have the same prefix as other interfaces in the
system. On Nvidia Spectrum-1 machines all the RIFs have to have the same
38-bit MAC address prefix. Since the bridge does not obey this limitation,
the RIF cannot be created, and the enslavement attempt is vetoed on the
grounds of the configuration not being offloadable.

These two selftests however check mirroring traffic to a gretap netdevice.
The bridge here does not participate in routing traffic and the IP address
or the RIF are irrelevant.

Fix by disabling automatic IPv6 address generation for the HW-offloaded
bridges in these selftests, thus exempting them from mlxsw router
attention. Since the bridges are only used for L2 forwarding, this change
should not hinder usefulness of this selftest for testing SW datapath or HW
datapaths in other devices.

Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In a future patch, mlxsw will start adding RIFs to uppers of front panel
port netdevices, if they have an IP address.

At the time that the front panel port is enslaved to the bridge, the bridge
MAC address does not have the same prefix as other interfaces in the
system. On Nvidia Spectrum-1 machines all the RIFs have to have the same
38-bit MAC address prefix. Since the bridge does not obey this limitation,
the RIF cannot be created, and the enslavement attempt is vetoed on the
grounds of the configuration not being offloadable.

The selftest itself however checks whether skbedit changes packet priority
as appropriate. The bridge thus does not need to participate in routing
traffic and the IP address or the RIF are irrelevant.

Fix by disabling automatic IPv6 address generation for the HW-offloaded
bridge in this selftest, thus exempting it from mlxsw router attention.
Since the bridge is only used for L2 forwarding, this change should not
hinder usefulness of this selftest for testing SW datapath or HW datapaths
in other devices.

Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In a future patch, mlxsw will start adding RIFs to uppers of front panel
port netdevices, if they have an IP address.

At the time that the front panel port is enslaved to the bridge, the bridge
MAC address does not have the same prefix as other interfaces in the
system. On Nvidia Spectrum-1 machines all the RIFs have to have the same
38-bit MAC address prefix. Since the bridge does not obey this limitation,
the RIF cannot be created, and the enslavement attempt is vetoed on the
grounds of the configuration not being offloadable.

The selftest itself however checks operation of pedit on IPv4 and IPv6
dsfield and its parts. The bridge thus does not need to participate in
routing traffic and the IP address or the RIF are irrelevant.

Fix by disabling automatic IPv6 address generation for the HW-offloaded
bridge in this selftest, thus exempting it from mlxsw router attention.
Since the bridge is only used for L2 forwarding, this change should not
hinder usefulness of this selftest for testing SW datapath or HW datapaths
in other devices.

Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In a future patch, mlxsw will start adding RIFs to uppers of front panel
port netdevices, if they have an IP address.

This will cause this selftest to fail spuriously. The swp enslavement to
the 802.1ad bridge is not allowed, because RIFs are not allowed to be
created for 802.1ad bridges, but the address indicates one needs to be
created.

Fix by disabling automatic IPv6 address generation for the HW-offloaded
bridge in this selftest, thus exempting it from mlxsw router attention.

Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In a future patch, mlxsw will start adding RIFs to uppers of front panel
port netdevices, if they have an IP address.

This will cause this selftest to fail spuriously. The swp enslavement to
the 802.1ad bridge is not allowed, because RIFs are not allowed to be
created for 802.1ad bridges, but the address indicates one needs to be
created.

Fix by disabling automatic IPv6 address generation for the HW-offloaded
bridge in this selftest, thus exempting it from mlxsw router attention.

Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Currently for each timestamp frame, the SW needs to go and read the
received timestamp over the MDIO bus. But the HW has the capability
to store the received nanoseconds part and the least significant two
bits of the seconds in the reserved field of the PTP header. In this
way we could save few MDIO transactions (actually a little more
transactions because the access to the PTP registers are indirect)
for each received frame.

Instead of reading the rest of seconds part of the timestamp of the
frame using MDIO transactions schedule PTP worker thread to read the
seconds part every 500ms and then for each of the received frames use
this information. Because if for example running with 512 frames per
second, there is no point to read 512 times the second part.

Doing all these changes will give a great CPU usage performance.
Running ptp4l with logSyncInterval of -9 will give a ~60% CPU
improvement.

Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Bartosz Golaszewski says:

====================
net: stmmac: dwmac-qcom-ethqos: add support for EMAC4

Extend the dwmac-qcom-ethqos driver to support EMAC4. While at it: rework the
code somewhat. The bindings have been reviewed by DT maintainers.

This is a sub-series of [1] with only the patches targetting the net subsystem
as they can go in independently.

[1] https://lore.kernel.org/lkml/20230617001644.4e093326@kernel.org/T/
====================

Link: https://lore.kernel.org/r/20230619092402.195578-1-brgl@bgdev.pl


Signed-off-by: Jakub Kicinski <kuba@kernel.org>

sa8775p uses EMAC version 4, add the relevant defines, rename the
has_emac3 switch to has_emac_ge_3 (has emac greater-or-equal than 3)
and add the new compatible.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add the compatible for the MAC controller on sa8775p platforms. This MAC
works with a single interrupt so add minItems to the interrupts property.
The fourth clock's name is different here so change it. Enable relevant
PHY properties. Add the relevant compatibles to the binding document for
snps,dwmac as well.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

On some platforms, the PCS can be integrated in the MAC so the driver
will not see any PCS link activity. Add a switch that allows the platform
drivers to let the core code know.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

On sa8775p the MAC is connected to the external PHY over SGMII so add
support for it to the driver.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In preparation for supporting SGMII, let's make the code a bit more
generic. Add a new callback for MAC configuration so that we can assign
a different variant of it in the future.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

On sa8775p, the EMAC revision is 4 and we use SGMII instead of RGMII.
There's no "rgmii" clock but there's a fourth clock under a different
name: "phyaux". Add a new field to the chip data struct that specifies
the link clock name. Default to "rgmii" for backward compatibility.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

On sa8775p platforms, there's a SGMII SerDes PHY between the MAC and
external PHY that we need to enable and configure.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

There's an unnecessary space in the rgmii_updatel() function, remove it.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Typically we use a newline between global and local headers so add it
here as well.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

device_get_phy_mode() is declared in linux/property.h but this header
is not included.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Shrink code and avoid line breaks by using a helper variable for
&pdev->dev.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Make sure we follow the reverse-xmas tree convention.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The err_mem label's name is unclear. It actually should be reached on
any error after stmmac_probe_config_dt() succeeds. Name it after the
cleanup action that needs to be called before exiting.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

We can use a devm action to completely drop the remove callback and use
stmmac_pltfr_remove() directly for remove. We can also drop one of the
goto labels.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The new efx_bind_neigh() function contains a broken code path when IPV6 is
disabled:

drivers/net/ethernet/sfc/tc_encap_actions.c:144:7: error: variable 'n' is used uninitialized whenever 'if' condition is true [-Werror,-Wsometimes-uninitialized]
                if (encap->type & EFX_ENCAP_FLAG_IPV6) {
                    ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/sfc/tc_encap_actions.c:184:8: note: uninitialized use occurs here
                if (!n) {
                     ^
drivers/net/ethernet/sfc/tc_encap_actions.c:144:3: note: remove the 'if' if its condition is always false
                if (encap->type & EFX_ENCAP_FLAG_IPV6) {
                ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/sfc/tc_encap_actions.c:141:22: note: initialize the variable 'n' to silence this warning
                struct neighbour *n;
                                   ^
                                    = NULL

Change it to use the existing error handling path here.

Fixes: 7e5e7d80

 ("sfc: neighbour lookup for TC encap action offload")
Suggested-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://lore.kernel.org/r/20230619091215.2731541-2-arnd@kernel.org


Signed-off-by: Jakub Kicinski <kuba@kernel.org>