Merge tag 'davinci-for-v4.10/dt-4' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/dt

- Add device tree nodes for pin pull-up/pull-down
bias control on DA850.

- Enable high speed support on DA850 MMC/SD

* tag 'davinci-for-v4.10/dt-4' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci

:
  ARM: dts: da850: enable high speed for mmc
  ARM: dts: da850: Add node for pullup/pulldown pinconf

Signed-off-by: Olof Johansson <olof@lixom.net>

The mmc controller in da850 supports high speed modes
so add cap-sd-highspeed and cap-mmc-highspeed.

Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>

This SoC has a separate pin controller for configuring pullup/pulldown
bias on groups of pins.

Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>

Merge tag 'omap-for-v4.10/dt-late-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt

Pull "omap dts changes for v4.10, part 2" from Tony Lindgren:

Second set of device tree changes for omaps for v4.10 merge window:

- Fix up new instances of gpio-key,wakeup to use wakeup-source

- Add beaglebone LCDC blue-and-red-wiring property to make use
  of the new driver features

- Add bindings for IIO support for am335x and am437x

- Add palmas PMIC overide powerhold property for am57xx

- Update am335x-baltos to use phy-handle property

- Add initial support for am571x-idk

* tag 'omap-for-v4.10/dt-late-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: AM571x-IDK Initial Support
  ARM: dts: am335x-baltos: use phy-phandle declarations
  ARM: dts: am57xx-idk-common: Add overide powerhold property
  ARM: dts: am57xx-beagle-x15-common: Add overide powerhold property
  ARM: dts: am57xx-idk: Add Industrial output support
  ARM: dts: am57xx-idk: Add Industrial input support
  ARM: dts: am437x-idk: Add Industrial output support
  ARM: dts: am437x-idk: Add Industrial input support
  ARM: dts: am335x-icev2: Add ADC support
  ARM: dts: am335x-icev2: Disable Industrial I/O LEDs and fix naming
  ARM: dts: am335x-icev2: Add Industrial input support
  ARM: dts: am335x-boneblack: Add blue-and-red-wiring -property to LCDC node
  ARM: dts: omap5: replace gpio-key,wakeup with wakeup-source property

Pull "mvebu dt for 4.10 (part 1)" from Gregory CLEMENT:

Add Turris Omnia support, an open hardware router Armada 385 based

* tag 'mvebu-dt-4.10-2' of git://git.infradead.org/linux-mvebu:
  ARM: dts: add support for Turris Omnia
  devicetree: Add vendor prefix for CZ.NIC

Merge tag 'berlin-dt-for-v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jszhang/linux-berlin into next/dt

Pull "Berlin DT changes for v4.10" from Jisheng Zhang:

- fix DTC compiler warning
- fix typo in chosen node

* tag 'berlin-dt-for-v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jszhang/linux-berlin:
  ARM: dts: berlin2q-marvell-dmp: fix typo in chosen node
  ARM: dts: berlin2q-marvell-dmp: fix regulators' name

Merge tag 'v4.10-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt

Pull "Rockchip dts32 changes for 4.10" from Heiko Stübner:

A bit of attention for the rk3066, fixed tsadc reset node
as well as enabling the dma for uart and mmc controllers.

And one new soc, the rk1108 combining a single-core Cortex-A7
with a separate DSP core.

* tag 'v4.10-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  ARM: dts: rockchip: add the sdmmc pinctrl for rk1108
  ARM: dts: rockchip: add rockchip RK1108 Evaluation board
  ARM: dts: rockchip: add basic support for RK1108 SOC
  clk: rockchip: add dt-binding header for rk1108
  dt-bindings: rockchip-dw-mshc: add RK1108 dw-mshc description
  ARM: dts: rockchip: enable dma for uart and mmc on rk3066a
  ARM: dts: rockchip: fix TSADC reset node for rk3066a

Merge tag 'qcom-dts-for-4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/dt

Pull "Qualcomm Device Tree Changes for v4.10 - Part 2" from Andy Gross:

* Add SDHC xo clk

* tag 'qcom-dts-for-4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
  ARM: dts: Add xo to sdhc clock node on qcom platforms

Merge tag 'samsung-dt-4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt

Pull "Samsung DeviceTree second update for v4.10" from Krzysztof Kozłowski:

1. Cleanups in MSHC nodes.
2. Enable ADC on Odroid boards.
3. Fix interrupt flags on recently added DMA sound nodes in Exynos5410.

* tag 'samsung-dt-4.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
  ARM: dts: exynos: Remove the cd-gpios property for eMMC of Odroid XU3/4
  ARM: dts: exynos: Specify snps, dwmac in compatible string for gmac
  ARM: dts: exynos: Fix invalid GIC interrupt flags in audio block of Exynos5410
  ARM: dts: exynos: Add ADCs on 4412 and 5422 based odroid boards.
  ARM: dts: exynos: Replace "clock-freq-min-max" with "max-frequency"

Pull "Broadcom devicetree changes for 4.10" from Florian Fainelli:

This pull request contains Broadcom ARM-based SoC Device Tree changes for 4.10,
please pull the following:

- Rafal adds support for the Netgear R8500 routers, adds basic support
  for the Tenda AC9 router which uses the new BCM53573 SoC (single core Cortex
  A7). He also enables the UART on the Netgear R8000 and restructures the
  include files a bit for the BCM47094 SoC, finally he adds USB 3.0 PHY nodes
  which enables USB 3.0 on BCM5301X devices that support it. Finally he adds
  support for the TP-LINK Archer C9 V1 router.

- Kamal adds support for the QSPI controller on the Northstar Plus SoCs and updates
  the bcm958625k reference board to have it enabled

- Dan adds support for the Luxul XAP-1510 (using a BCM4708) and XWR-3100 (using
  a BCM47094)

- Scott fixes the pinctrl names in the Cygnus DTS files

- Jonathan enables the Broadcom iProc mailbox controller for Broadcom Cygnus/iProc
  SoCs, he adds interrupt support for the GPIO CRMU hardware block and finally adds
  the node for the OTP controller found on Cygnus SoCs

- Dhananjay enables the GPIO B controller on Norstarh Plus SoCs

- Eric defines standard pinctrl groups in the BCM2835 GPIO node

- Gerd adds definitions for the pinctrl groups and updates the PWM, I2C and SDHCI nodes
  to use their appropriate pinctrl functions

- Linus adds names for the Raspberry Pi GPIO lines based on the datasheet

- Martin adds the DT binding and nodes for the Raspberry Pi firmware thermal block

- Stefan fixes a few typos with respect to the BCM2835 mailbox binding example and
  Device Tree nodes he also fixes the Raspberry Pi GPIO lines names and finally
  adds names for the Raspberry Zero GPIO lines

* tag 'arm-soc/for-4.10/devicetree' of http://github.com/Broadcom/stblinux: (29 commits)
  ARM: bcm2835: Add names for the RPi Zero GPIO lines
  ARM: bcm2835: Fix names for the Raspberry Pi GPIO lines
  ARM: dts: enable GPIO-b for Broadcom NSP
  ARM: BCM5301X: Add DT for TP-LINK Archer C9 V1
  ARM: dts: Add node for Broadcom OTP controller driver
  ARM: dts: Enable interrupt support for cygnus crmu gpio driver
  ARM: dts: Enable Broadcom iProc mailbox controller
  ARM: bcm2835: Add names for the Raspberry Pi GPIO lines
  ARM: bcm2835: dts: add thermal node to device-tree of bcm283x
  dt: bindings: add thermal device driver for bcm2835
  ARM: dts: bcm283x: fix typo in mailbox address
  DT: binding: bcm2835-mbox: fix address typo in example
  ARM: dts: cygnus: fix naming of pinctrl node
  ARM: BCM53573: Specify PMU and its ILP clock in the DT
  ARM: BCM5301X: Add DT for Luxul XWR-3100
  ARM: BCM5301X: Add DT for Luxul XAP-1510
  ARM: BCM5301X: Specify USB 3.0 PHY in DT
  ARM: BCM5301X: Enable UART on Netgear R8000
  ARM: BCM5301X: Add separated DTS include file for BCM47094
  ARM: dts: NSP: Add QSPI nodes to NSPI and bcm958625k DTSes
  ...

Merge tag 'socfpga_dts_for_v4.10_part_3' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into next/dt

Merge "SoCFPGA DTS update for v4.10, part 3" from Dinh Nguyen:

- Fine tune L2 cache configuration

* tag 'socfpga_dts_for_v4.10_part_3' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
  ARM: dts: socfpga: fine-tune L2 cache configuration

Merge tag 'renesas-dt2-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt

Pull "Second Round of Renesas ARM Based SoC DT Updates for v4.10" from Simon Horman:

Enhancements:
* Add device nodes for PRR
* Add r8a7745 SoC and sk-rzg1e board
* Add r8a7743 SoC and sk-rzg1m board
* Enable SDR-104 and I2C demuxer on alt, koelsch and lager boards

Corrections:
* Use SYSC "always-on" PM Domain for sound on r8a7794 SoC
* Correct hsusb parent clock on r8a7794 SoC
* Correct PFC names for DU on alt board

* tag 'renesas-dt2-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (33 commits)
  ARM: dts: r8a7794: Add device node for PRR
  ARM: dts: r8a7793: Add device node for PRR
  ARM: dts: r8a7792: Add device node for PRR
  ARM: dts: r8a7791: Add device node for PRR
  ARM: dts: r8a7790: Add device node for PRR
  ARM: dts: r8a7779: Add device node for PRR
  ARM: dts: r8a73a4: Add device node for PRR
  ARM: dts: sk-rzg1e: add Ether support
  ARM: dts: sk-rzg1e: initial device tree
  ARM: dts: r8a7745: add IRQC support
  ARM: dts: r8a7745: add Ether support
  ARM: dts: r8a7745: add [H]SCIF{|A|B} support
  ARM: dts: r8a7745: add SYS-DMAC support
  ARM: dts: r8a7745: initial SoC device tree
  ARM: dts: sk-rzg1m: add Ether support
  ARM: dts: sk-rzg1m: initial device tree
  ARM: dts: r8a7743: add IRQC support
  ARM: dts: r8a7743: add Ether support
  ARM: dts: r8a7743: add [H]SCIF{A|B} support
  ARM: dts: r8a7743: add SYS-DMAC support
  ...

Merge tag 'rzg-clock-defs-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into next/dt

Pull "Renesas RZ/G1M and RZ/G1E CPG Core Clock Definitions" from Geert Uytterhoeven:

Shared by clock drivers, and DTS files.

* tag 'rzg-clock-defs-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers:
  clk: renesas: Add r8a7745 CPG Core Clock Definitions
  clk: renesas: Add r8a7743 CPG Core Clock Definitions

Merge tag 'davinci-for-v4.10/dt-3' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/dt

Pull "DaVinci DT updates for v4.10 (part 3)" from Sekhar Nori:

Some fixes for device-tree patches already queued.
- Fix SD card detect polarity
- Prevent Ethernet from picking a random mac address
- Fix error messages on platforms which dont use
  bus master and emif priority settings.

* tag 'davinci-for-v4.10/dt-3' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
  ARM: dts: da850: enable memctrl and mstpri nodes per board
  ARM: dts: da850-lcdk: Add ethernet0 alias to DT
  ARM: dts: da850-lcdk: fix mmc card detect polarity

Merge tag 'davinci-for-v4.10/dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/dt

Pull "DaVinci DT updates for v4.10 (part 2)" from Sekhar Nori:

Adds device tree nodes enabling DDR controller
and bus master priority settings needed for
stable LCDC operation on DA850.

Also adds support for MUSB device on DA850
providing USB OTG support.

* tag 'davinci-for-v4.10/dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
  ARM: dts: da850-lcdk: Enable the usb otg device node
  ARM: dts: da850: Add the usb otg device node
  ARM: dts: da850: add the mstpri and ddrctl nodes

Currently the memory controller and master priorities drivers are
enabled in da850.dtsi. For boards for which there are no settings
defined, this makes these drivers emit error messages.

Disable the nodes in da850.dtsi and only enable them for da850-lcdk -
the only board that currently needs them.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>

In order to avoid Linux generating a random mac address on every boot,
add an ethernet0 alias that will allow u-boot to patch the dtb with
the MAC address programmed into the EEPROM.

Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>

Merge tag 'sunxi-dt-for-4.10-bis' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt

Pull "Allwinner DT additions for 4.10, bis" from Maxime Ripard:

The usual bunch of DT additions, but most notably:
  - A31 DRM driver
  - A31 audio codec
  - WiFi for the A80-Based boards and the CHIP
  - Support for the NextThing Co CHIP Pro (the first board with NAND
    enabled)
  - New board: NanoPi M1

* tag 'sunxi-dt-for-4.10-bis' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (41 commits)
  ARM: dts: sun6i: hummingbird-a31: Enable display output through VGA bridge
  ARM: dts: sun5i: Add touchscreen node to reference-design-tablet.dtsi
  ARM: sunxi: Add the missing clocks to the pinctrl nodes
  ARM: dts: sun7i: bananapi-m1-plus: Enable USB OTG
  ARM: dts: sun7i: bananapi-m1-plus: Add PMIC regulators
  ARM: dts: sun7i: bananapi-m1-plus: Enable USB PHY for USB host support
  ARM: sun8i: sina33: Enable USB gadget
  ARM: dts: sun8i: reference-design-tablet: ldo_io1 is vcc-touchscreen
  ARM: dts: sun8i: replace enable-sdio-wakeup with wakeup-source for BananaPi M1+
  ARM: gr8: evb: Add i2s codec
  ARM: dts: sun6i: sina31s: Enable internal audio codec
  ARM: dts: sun6i: hummingbird: Enable internal audio codec
  ARM: dts: sun6i: Add audio codec device node
  ARM: gr8: evb: Enable SPDIF
  ARM: dts: sun8i: Add SPI controller node in H3
  ARM: dts: sun8i: Add SPI pinctrl node in H3
  ARM: dts: sun8i: Add dts file for NanoPi M1 SBC
  ARM: dts: sun8i: Use the common file in NanoPi NEO SBC
  ARM: dts: sun8i: Add common dtsi file for NanoPi SBCs
  ARM: dts: sun9i: cubieboard4: Enable AP6330 WiFi
  ...

Pull "mvebu dt for 4.10 (part 1)" from Gregory CLEMENT:

Add missing pinmux declaration for netgear NASes
Fix i2c compatible string for netgear NASes
Fix on a wrong comment about PLL frequency
Fix spelling mistake of the manufacturer's name of the Topkick
Add dt support for the orion5x ls-chl Linkstation device
First step of fixing DTC warning for Armada 370, 375 and XP

* tag 'mvebu-dt-4.10-1' of git://git.infradead.org/linux-mvebu: (30 commits)
  ARM: dts: armada-375: Fixup ethernet child DT warning
  ARM: dts: armada-375: Fixup memory DT warning
  ARM: dts: armada-375: Remove skeleton.dtsi
  ARM: dts: armada-375: Fixup pinctrl DT warnings
  ARM: dts: armada-375: Fixup pcie DT warnings
  ARM: dts: armada-375: Fixup mdio DT warning
  ARM: dts: armada-375: Use the node labels
  ARM: dts: armada-375: Add node labels
  ARM: dts: armada-370-xp: Fixup regulator DT warning
  ARM: dts: armada-370-xp: Remove button address and fixup names
  ARM: dts: armada-370-xp: Remove address from dsa unit name
  ARM: dts: armada-370-xp: Fixup memory DT warning
  ARM: dts: armada-370-xp: Fixup l2-cache DT warning
  ARM: dts: armada-370-xp: Remove skeleton.dtsi
  ARM: dts: armada-370: Fixup pcie DT warnings
  ARM: dts: armada-xp: Fixup pcie DT warnings
  ARM: dts: armada-370-xp: Fixup mdio DT warning
  ARM: dts: armada-370-xp: Use the node labels
  ARM: dts: armada-370-xp: add node labels
  ARM: dts: armada-370-xp: move the cpurst node in the common file
  ...

Merge tag 'qcom-dts-for-4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/dt

Pull "Qualcomm Device Tree Changes for v4.10 - v2" from Andy Gross:

* Add EBI2 support to MSM8660
* Add SMSC ethernet support to APQ8060
* Add support for display, pstore, iommu, and hdmi to APQ8064
* Add SDHCI node to MSM8974 Hammerhead
* Add WP8548 MangOH board support (MDM9615)

* tag 'qcom-dts-for-4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
  ARM: dts: add SMSC ethernet on the APQ8060 Dragonboard
  ARM: dts: add EBI2 to the Qualcomm MSM8660 DTSI
  arm: dts: qcom: apq8064-nexus7: Add pstore support to nexus7
  arm: dts: qcom: apq8064-nexus7: Add DSI and panel nodes
  arm: dts: qcom: apq8064: Add dsi, gpu and iommu nodes
  arm: dts: qcom: apq8064-ifc6410: Add HDMI support
  arm: dts: qcom: apq8064: Add display DT nodes
  ARM: dts: qcom: msm8974-hammerhead: Add sdhci1 node
  dt-bindings: arm: Add Sierra Wireless modules bindings
  ARM: dts: Add WP8548 based MangOH Green board DTS
  ARM: dts: Add Sierra Wireless WP8548 dtsi
  dt-bindings: qcom: Add MDM9615 bindings
  ARM: dts: Add MDM9615 dtsi

Pull "This device-tree pxa update brings" from Robert Jarzmik:

 - pxa25x support
 - cpu operating points in preparation for cpufreq-dt
 - small fixes

* tag 'pxa-dt-4.10' of https://github.com/rjarzmik/linux:
  ARM: dts: pxa: add pxa27x cpu operating points
  ARM: dts: pxa: add pxa25x cpu operating points
  ARM: dts: pxa: fix gpio0 and gpio1 interrupts
  ARM: dts: pxa: fix no. of gpio cells in the pxa gpio binding documentation
  ARM: dts: pxa: add pxa25x .dtsi file

Add PCIe support to the ARTPEC-6 SoC. This uses the existing
pcie-artpec6 driver.
So, all that is needed is device tree entries in the DTS.

Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Jesper Nilsson <jespern@axis.com>

Pull "ARM: OXNAS SoC DT updates for 4.10" from Neil Armstrong:

- Add DTSI for Oxford Semiconductor OX820
- Add DTS for Cloud Engines PogoPlug v3 board
- Fix MAINTAINERS Oxnas entry for dts files
from http://lkml.kernel.org/r/20161102141850.25164-1-narmstrong@baylibre.com

* tag 'oxnas-arm-soc-dt-for-4.10' of https://github.com/OXNAS/linux:
  MAINTAINERS: oxnas: Add new files definitions
  ARM: dts: Add support for OX820 and Pogoplug V3

This machine is an open hardware router by cz.nic driven by a
Marvell Armada 385.

Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Tomas Hlavacek <tmshlvck@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>

This patch fixes the following DTC warnings with W=1:

Warning (unit_address_vs_reg): Node /regulators/regulator@0 has a unit
name, but no reg property
Warning (unit_address_vs_reg): Node /regulators/regulator@1 has a unit
name, but no reg property
Warning (unit_address_vs_reg): Node /regulators/regulator@2 has a unit
name, but no reg property
Warning (unit_address_vs_reg): Node /regulators/regulator@3 has a unit
name, but no reg property
Warning (unit_address_vs_reg): Node /regulators/regulator@4 has a unit
name, but no reg property

Signed-off-by: Jisheng Zhang <jszhang@marvell.com>

Add xo entry to sdhc clock node on all qcom platforms.

Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

Qualcomm Device Tree Changes for v4.10 - v2

* Add EBI2 support to MSM8660
* Add SMSC ethernet support to APQ8060
* Add support for display, pstore, iommu, and hdmi to APQ8064
* Add SDHCI node to MSM8974 Hammerhead
* Add WP8548 MangOH board support (MDM9615)

Add a device node for the Product Register, which provides SoC product
and revision information.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a device node for the Product Register, which provides SoC product
and revision information.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a device node for the Product Register, which provides SoC product
and revision information.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a device node for the Product Register, which provides SoC product
and revision information.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a device node for the Product Register, which provides SoC product
and revision information.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a device node for the Product Register, which provides SoC product
and revision information.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a device node for the Product Register, which provides SoC product
and revision information.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Define the SK-RZG1E board dependent part of the Ether device node.
Enable DHCP and NFS root  for the kernel booting.

Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add the initial  device tree for the R8A7745 SoC based SK-RZG1E board.
The board has 1  debug  serial  port (SCIF2); include support for it,
so that the serial console can  work.

Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Describe the IRQC interrupt controller in the R8A7745 device tree.

Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Define the generic R8A7745 part of the Ether device node.

Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>