If an IRQ has been configured for wakeup via enable_irq_wake(), the
driver who has done that must be prepared for receiving interrupts
after suspend_device_irqs() has returned, so there is no need to
"suspend" such IRQs.  Moreover, if drivers using enable_irq_wake()
actually want to receive interrupts after suspend_device_irqs() has
returned, they need to add IRQF_NO_SUSPEND to the IRQ flags while
requesting the IRQs, which shouldn't be necessary (it also goes a bit
too far, as IRQF_NO_SUSPEND causes the IRQ to be ignored by
suspend_device_irqs() all the time regardless of whether or not it
has been configured for signaling wakeup).

For the above reasons, make __disable_irq() ignore IRQ descriptors
with IRQD_WAKEUP_STATE set when its suspend argument is true which
effectively causes them to behave like IRQs with IRQF_NO_SUSPEND
set.

This also allows IRQs configured for wakeup via enable_irq_wake()
to work as wakeup interrupts for the "freeze" (suspend-to-idle)
sleep mode automatically just like for any other sleep states.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Li Aubrey <aubrey.li@linux.intel.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk>
Link: http://lkml.kernel.org/r/4679574.kGUnqAuNl9@vostro.rjw.lan
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

irqchip core changes form Jason Cooper
 * or1k-pic: Migrate driver from arch/openrisc
 * crossbar: Cleanup series

In addition to consolidating the or1k-pic with other interrupt
controllers, this makes OpenRISC less tied to its on-cpu
interrupt controller.

All or1k-pic specific parts are moved out of irq.c and into
drivers/irqchip/irq-or1k-pic.c

In that transition, the functionality have been divided into
three chip variants.
One that handles level triggered interrupts, one that handles edge
triggered interrupts and one that handles the interrupt
controller that is present in the or1200 OpenRISC cpu
implementation.

Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Link: https://lkml.kernel.org/r/1401136302-27654-1-git-send-email-stefan.kristiansson@saunalahti.fi
Acked-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

On certain platforms such as DRA7, SPIs 0, 1, 2, 3, 5, 6, 10, 131,
132, 133 are direct wired to hardware blocks bypassing crossbar.
This quirky implementation is *NOT* supposed to be the expectation
of crossbar hardware usage. However, these are already marked in our
description of the hardware with SKIP and RESERVED where appropriate.

Unfortunately, we need to be able to refer to these hardwired IRQs.
So, to request these, crossbar driver can use the existing information
from it's table that these SKIP/RESERVED maps are direct wired sources
and generic allocation/programming of crossbar should be avoided.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Link: https://lkml.kernel.org/r/1403766634-18543-17-git-send-email-r.sricharan@ti.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

The current crossbar description does not include the description
required for the consumer of the crossbar, a.k.a devices whoes events
pass through the crossbar into the GIC interrupt controller.

So, provide documentation for the same.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Link: https://lkml.kernel.org/r/1403766634-18543-16-git-send-email-r.sricharan@ti.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

This is a basic check to ensure that crossbar register needs to be
written. This ensures that we have a common check which is used in
both map and unmap logic.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Link: https://lkml.kernel.org/r/1403766634-18543-15-git-send-email-r.sricharan@ti.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Currently we attempt to map any crossbar value to an IRQ, however,
this is not correct from hardware perspective. There is a max crossbar
event number upto which hardware supports. So describe the same in
device tree using 'ti,max-crossbar-sources' property and use it to
validate requests.

[ jac - remove MAX_SOURCES from binding doc, use integer because we
shouldn't put implementation details in the binding docs ]

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Link: https://lkml.kernel.org/r/1403766634-18543-14-git-send-email-r.sricharan@ti.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Adding kerneldoc for unmap callback function.

Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Link: https://lkml.kernel.org/r/1403766634-18543-13-git-send-email-r.sricharan@ti.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

If crossbar_of_init returns with a error, then set the cb pointer
to null.

Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Link: https://lkml.kernel.org/r/1403766634-18543-12-git-send-email-r.sricharan@ti.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Using err1,2,3,4 etc makes it hard to ensure a new exit path in the
middle will not result in spurious changes, so rename the error paths
as per the function it does.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Link: https://lkml.kernel.org/r/1403766634-18543-11-git-send-email-r.sricharan@ti.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

crossbar_of_init always returns -ENOMEM in case of errors.
There can be other causes of failure like invalid data from
DT. So return a appropriate error value for that case.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Link: https://lkml.kernel.org/r/1403766634-18543-10-git-send-email-r.sricharan@ti.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Adding missing properties for kerneldoc (@write) and cleanup
of harmless warnings while we are here.

kerneldoc warnings:
Warning(drivers/irqchip/irq-crossbar.c:27): missing initial short description on line:
 * struct crossbar_device: crossbar device description
Info(drivers/irqchip/irq-crossbar.c:27): Scanning doc for struct
Warning(drivers/irqchip/irq-crossbar.c:39): No description found for parameter 'write'
2 warnings

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Link: https://lkml.kernel.org/r/1403766634-18543-9-git-send-email-r.sricharan@ti.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

There is absolutely no need for crossbar driver to expose functions and
variables into global namespace. So make them all static

Also fix a couple of checkpatch warnings.

Fixes sparse warnings:
drivers/irqchip/irq-crossbar.c:129:29: warning: symbol 'routable_irq_domain_ops' was not declared. Should it be static?
drivers/irqchip/irq-crossbar.c:261:12: warning: symbol 'irqcrossbar_init' was not declared. Should it be static?

Checkpatch warnings:
WARNING: Prefer kcalloc over kzalloc with multiply
+	cb->irq_map = kzalloc(max * sizeof(int), GFP_KERNEL);

WARNING: Prefer kcalloc over kzalloc with multiply
+	cb->register_offsets = kzalloc(max * sizeof(int), GFP_KERNEL);

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Link: https://lkml.kernel.org/r/1403766634-18543-8-git-send-email-r.sricharan@ti.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

IS_ERR_VALUE makes sense only *if* there could be valid values in
negative error range. But in the cases that we do use it, there is no
such case. Just remove the same.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Link: https://lkml.kernel.org/r/1403766634-18543-7-git-send-email-r.sricharan@ti.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Reverse the search algorithm to ensure that address mapping and IRQ
allocation logics are proper. This makes the below bugs visible sooner.

class 1. address space errors -> example:
reg = <a size_b>
ti,max-irqs =  is a wrong parameter

class 2: irq-reserved list - which decides which entries in the
address space is not actually wired in

class 3: wrong list of routable-irqs.

In general allocating from max to min tends to have benefits in
ensuring the different issues that may be present in dts is easily
caught at definition time, rather than at a later point in time.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Link: https://lkml.kernel.org/r/1403766634-18543-6-git-send-email-r.sricharan@ti.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Since crossbar is s/w configurable, the initial settings of the
crossbar cannot be assumed to be sane. This implies that:
a) On initialization all un-reserved crossbars must be initialized to
   a known 'safe' value.
b) When unmapping the interrupt, the safe value must be written to
   ensure that the crossbar mapping matches with interrupt controller
   usage.

So provide a safe value in the dt data to map if
'0' is not safe for the platform and use it during init and unmap

While at this, fix the below checkpatch warning.
Fixes checkpatch warning:
WARNING: Unnecessary space before function pointer arguments
 #37: FILE: drivers/irqchip/irq-crossbar.c:37:
 +	void (*write) (int, int);

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Link: https://lkml.kernel.org/r/1403766634-18543-5-git-send-email-r.sricharan@ti.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

When, in the system due to varied reasons, interrupts might be unusable
due to hardware behavior, but register maps do exist, then those interrupts
should be skipped while mapping irq to crossbars.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Link: https://lkml.kernel.org/r/1403766634-18543-4-git-send-email-r.sricharan@ti.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

If irq_of_parse_and_map is executed twice, the same crossbar is mapped to two
different GIC interrupts. This is completely undesirable. Instead, check
if the requested crossbar event is pre-allocated and provide that GIC
mapping back to caller if already allocated.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Link: https://lkml.kernel.org/r/1403766634-18543-3-git-send-email-r.sricharan@ti.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Today '0' is actually reserved, but may not be the same in the future.

So, use a flag to mark the GIC interrupts that are reserved.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Link: https://lkml.kernel.org/r/1403766634-18543-2-git-send-email-r.sricharan@ti.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

irqchip core changes for v3.17
 * nvic: use generic noop function
 * spear_shirq: generic cleanup, simplification, and refactoring

Reason: The next pull request depends on that

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

The extra register data structure is pointless. Move the offsets of
the status and the mask register into the shirq block structure.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20140619212713.923306179@linutronix.de
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Only spear300 has an actual mask register for the RAS interrupts. Add
an irq chip pointer to the shirq struct and initialize spear300 with
the actual implementation and the others with dummy_irq_chip. The
disabled RAS3 block has no irq chip assigned, so we can check for this
and remove the disabled member.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20140619212713.831341023@linutronix.de
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

"ack" is actually a mask in the parent irq. The demultiplexer and the
handlers run with interrupts disabled. No point in masking and
unmasking the parent.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20140619212713.754300980@linutronix.de
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

I don't know if there are less efficient ways to code that. Get rid of
the loop mess and use efficient code.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20140619212713.662897061@linutronix.de
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

None of the chips has a ACK register. The code brainlessly fiddles
with the enable register, so it might even reenable a disabled
interrupt at least on spear300.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20140619212713.570396433@linutronix.de
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Calculate the status mask at compile time, not at runtime.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20140619212713.496614337@linutronix.de
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

No point in doing a full irq lookup, when the desc pointer is
available.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20140619212713.404243909@linutronix.de
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Order the ras blocks in the order of interrupts not alphabetically.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20140619212713.310591579@linutronix.de
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

The struct members of the shirq block struct are named to confuse the
hell out of the casual reader. Clean it up.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20140619212713.219411832@linutronix.de
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

The struct member is pointless and a nismomer as well.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20140619212713.129694036@linutronix.de
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

No point in having them in a separate header file. Make the init
functions static.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20140619212713.038658058@linutronix.de
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20140619212712.948802939@linutronix.de
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

The ras3 block on spear320 claims to have 3 interrupts. In fact it has
one and 6 reserved interrupts. Account the 6 reserved to this block so
it has 7 interrupts total. That matches the datasheet and the device
tree entries.

Broken since commit 80515a5a(ARM: SPEAr3xx: shirq: simplify and move
the shared irq multiplexor to DT). Testing is overrated....

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20140619212712.872379208@linutronix.de
Fixes: 80515a5a2e3c ('ARM: SPEAr3xx: shirq: simplify and move the shared irq multiplexor to DT')
Cc: <stable@vger.kernel.org> # v3.8+
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Export irq_domain_disassociate() to architecture interrupt drivers,
so it could be used to handle legacy IRQ descriptors on x86.

Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1402302011-23642-37-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

Pull perf fixes from Ingo Molnar:
 "This is larger than usual: the main reason are the ARM symbol lookup
  speedups that came in late and were hard to resist.

  There's also a kprobes fix and various tooling fixes, plus the minimal
  re-enablement of the mmap2 support interface"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
  x86/kprobes: Fix build errors and blacklist context_track_user
  perf tests: Add test for closing dso objects on EMFILE error
  perf tests: Add test for caching dso file descriptors
  perf tests: Allow reuse of test_file function
  perf tests: Spawn child for each test
  perf tools: Add dso__data_* interface descriptons
  perf tools: Allow to close dso fd in case of open failure
  perf tools: Add file size check and factor dso__data_read_offset
  perf tools: Cache dso data file descriptor
  perf tools: Add global count of opened dso objects
  perf tools: Add global list of opened dso objects
  perf tools: Add data_fd into dso object
  perf tools: Separate dso data related variables
  perf tools: Cache register accesses for unwind processing
  perf record: Fix to honor user freq/interval properly
  perf timechart: Reflow documentation
  perf probe: Improve error messages in --line option
  perf probe: Improve an error message of perf probe --vars mode
  perf probe: Show error code and description in verbose mode
  perf probe: Improve error message for unknown member of data structure
  ...

Merge branch 'locking-urgent-for-linus.patch' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

Pull rtmutex fixes from Thomas Gleixner:
 "Another three patches to make the rtmutex code more robust.  That's
  the last urgent fallout from the big futex/rtmutex investigation"

* 'locking-urgent-for-linus.patch' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  rtmutex: Plug slow unlock race
  rtmutex: Detect changes in the pi lock chain
  rtmutex: Handle deadlock detection smarter

Pull s390 patches from Martin Schwidefsky:
 "A couple of bug fixes, a debug change for qdio, an update for the
  default config, and one small extension.

  The watchdog module based on diagnose 0x288 is converted to the
  watchdog API and it now works under LPAR as well"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/ccwgroup: use ccwgroup_ungroup wrapper
  s390/ccwgroup: fix an uninitialized return code
  s390/ccwgroup: obtain extra reference for asynchronous processing
  qdio: Keep device-specific dbf entries
  s390/compat: correct ucontext layout for high gprs
  s390/cio: set device name as early as possible
  s390: update default configuration
  s390: avoid format strings leaking into names
  s390/airq: silence lockdep warning
  s390/watchdog: add support for LPAR operation (diag288)
  s390/watchdog: use watchdog API
  s390/sclp_vt220: Enable ASCII console per default
  s390/qdio: replace shift loop by ilog2
  s390/cio: silence lockdep warning
  s390/uaccess: always load the kernel ASCE after task switch
  s390/ap_bus: Make modules parameters visible in sysfs