Do not enable wakeup for SDIO card interrupt unless the SDIO function
driver has requested it which is indicated by mmc_card_wake_sdio_irq().

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Do not unnecessarily enable card detect wakeup in the cases that the card
is not removable or a GPIO is used for card detect.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Now that tuning no longer leaves the Buffer Read Enable bit set (refer
intel_execute_tuning()), glk_cqe_enable() is no longer needed. Get rid of
it.

Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Not sure why it was there in the first place, but it's
obviously useless check, so let's remove it.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

cur_slot and num_slots has been removed from struct dw_mci in 42f989c0.
Unfortunately, inline documentation was not updated so far.

Fix @lock field documentation in Locking section.
Move @mrq field of struct dw_mci_slot mention closer to it
description, so no one could miss this slightest detail.

Couple of code style fixes as a bonus.

Signed-off-by: Alexey Roslyakov <alexey.roslyakov@gmail.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Clang reports a compile warning:
drivers/mmc/host/dw_mmc.c:2124:5: warning: Value stored to 'prev_state'
is never read

By checking the code, prev_state and state assignment for
STATE_SENDING_CMD is indeed never used after jumping to unlock tag.
So remove it.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Use the newly added macro to simply to the code.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

TMIO_MASK_CMD is properly enabled in tmio_mmc_start_command().

We have no reason to set it up in tmio_mmc_host_probe().  (If we
really wanted to set it in the probe, we would have to do likewise
when resuming.)

Even worse, the following code is extremely confusing:

  _host->sdcard_irq_mask &= ~irq_mask;

The logic is opposite between "->sdcard_irq_mask" and "irq_mask".
The intention is not clear at a glance.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Currently, force_pio is cleared when the driver exits.  Then, it
resulted in clearing it in multiple places since MMC drivers in
general have multiple exit points.

 tmio_mmc_reset_work - bails out on timeout
 tmio_process_mrq - error out when it cannot send a command
 tmio_mmc_finish_request - successful exit

This is error-prone since we may miss to cover all bail-out points.

To simplify the code, the data structure should be initialized just
before used since we have a single entrance.  force_pio is only used
for data transfer, so tmio_mmc_start_data() will be a suitable place
to clear this flag.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

As far as I tested the IP on UniPhier SoCs, TMIO_STAT_{RXRDY,TXRQ}
are asserted for DMA mode as well as for PIO.  I need to disable the
those IRQs in dma_ops->start hook, otherwise the DMA transfer fails
with the following error message:
  PIO IRQ in DMA mode!

Renesas chips are the same cases since I see their dma_ops->start
hooks explicitly clear TMIO_STAT_{RXRDY,TXRQ} (with nice comment!).

If we do this sanity check in TMIO MMC core, RXRDY/TXRQ handling
should be entirely moved to the core.  tmio_mmc_cmd_irq() will
be a suitable place to disable them.

The probe function sets TMIO_MASK_{READOP,WRITEOP} but this is odd.

    /* Unmask the IRQs we want to know about */
    if (!_host->chan_rx)
            irq_mask |= TMIO_MASK_READOP;
    if (!_host->chan_tx)
            irq_mask |= TMIO_MASK_WRITEOP;

At this point, _host->{chan_rx,chan_tx} are _always_ NULL because
tmio_mmc_request_dma() is called after this code.  Consequently,
TMIO_MASK_{READOP,WRITEOP} are set here whether DMA is used or not.
Remove this pointless code.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>

The TMIO mmc cannot detect the card insertion in native_hotplug mode
if the driver is probed without a card inserted.

The reason is obvious; all IRQs are disabled by tmio_mmc_host_probe(),
as follows:

  tmio_mmc_disable_mmc_irqs(_host, TMIO_MASK_ALL);

The card event IRQs are first enabled by tmio_mmc_start_command() as
follows:

  if (!host->native_hotplug)
          irq_mask &= ~(TMIO_STAT_CARD_REMOVE | TMIO_STAT_CARD_INSERT);
  tmio_mmc_enable_mmc_irqs(host, irq_mask);

If the driver is probed without a card, tmio_mmc_start_command() is
never called in the first place.  So, the card is never detected.

The card event IRQs must be enabled in probe/resume functions.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>

A card detect GPIO is set up only for platforms with "cd-gpios"
DT property or TMIO_MMC_USE_GPIO_CD flag.  However, the driver
core always uses mmc_gpio_get_cd, which just fails with -ENOSYS
if ctx->cd_gpio is unset.

The bit 5 of the status register provides the current signal level
of the CD line.  Allow to use it if the GPIO is unused.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>

This property is equivalent to "disable-wp" defined in
Documentation/devicetree/bindings/mmc/mmc.txt

The TMIO MMC core calls mmc_of_parse(), and it sets
MMC_CAP2_NO_WRITE_PROTECT if "disable-wp" property is present.

We do not need a vendor-specific property to do the same thing.

Let's remove the description from the dt-binding to prevent new boards
from using it.

I am keeping the driver code for existing DT files, but added
comments that this is deprecated.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>

The use of this flag has been replaced with MMC_CAP2_NO_WRITE_PROTECT.
No platform defines this flag any more.  Remove.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>

TMIO_MMC_WRPROTECT_DISABLE is equivalent to MMC_CAP2_NO_WRITE_PROTECT.

Only the difference is the TMIO_... makes tmio_mmc_get_ro() return 0
(i.e. it does not affect mmc_gpio_get_ro() at all), while MMC_CAP2_...
returns 0 before calling ->get_ro() hook (i.e. it affects both IP own
logic and GPIO detection).

The TMIO MMC drivers do not set-up gpio_ro by themselves.  Only the
possibility, if any, would be DT specifies "wp-gpios" property, and
gpio_ro is set by mmc_gpiod_request_ro() called from mmc_of_parse().
However, it does not make sense to specify "wp-gpios" property and
"toshiba,mmc-wrprotect-disable" at the same time.

I checked under arch/arm/boot/dts/ and arch/arm64/boot/dts/renesas/,
and I did not see any Renesas boards with "wp-gpios".  So, this
conversion should be safe.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>

TMIO_MMC_WRPROTECT_DISABLE is equivalent to MMC_CAP2_NO_WRITE_PROTECT.

The flag is propagated as follows:
    tmio_mmc_data::capabilities2 -> mmc_host::caps2

Only the difference is the TMIO_... makes tmio_mmc_get_ro() return 0
(i.e. it does not affect mmc_gpio_get_ro() at all), while MMC_CAP2_...
returns 0 before calling ->get_ro() hook (i.e. it affects both IP own
logic and GPIO detection).

The TMIO MMC drivers do not set-up gpio_ro by themselves, so gpio_ro
is obviously unused by legacy boards like this.  So, this conversion
should be safe.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>

TMIO_MMC_WRPROTECT_DISABLE is equivalent to MMC_CAP2_NO_WRITE_PROTECT.

The flag is propagated as follows:
       renesas_sdhi_of_data::capabilities2
    -> tmio_mmc_data::capabilities2
    -> mmc_host::caps2

Only the difference is the TMIO_... makes tmio_mmc_get_ro() return 0
(i.e. it does not affect mmc_gpio_get_ro() at all), while MMC_CAP2_...
returns 0 before calling ->get_ro() hook (i.e. it affects both IP own
logic and GPIO detection).

The TMIO MMC drivers do not set-up gpio_ro by themselves.  Only the
possibility, if any, would be DT specifies "wp-gpios" property, and
gpio_ro is set by mmc_gpiod_request_ro() called from mmc_of_parse().
However, it does not make sense to specify "wp-gpios" property and
TMIO_MMC_WRPROTECT_DISABLE at the same time.

I checked under arch/arm/boot/dts/ and arch/arm64/boot/dts/renesas/,
and I did not see any Renesas boards with "wp-gpios".  So, this
conversion should be safe.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>

According to the BCM2835 datasheet there are no preset value registers.
This wasn't an issue before, because we didn't propagate 1.8V support.

Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

If the max_discard value is zero, the conditional branch that checks the
trim capabilities will never update this value with max_trim.

Change the condition statement to also check the max_discard value in order
to avoid an unnecessary call to mmc_do_calc_max_discard.

Signed-off-by: Sergio Valverde <vlvrdv@gmail.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chip.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The TODO section from 2010 is obsolete. We have DMA and PM meanwhile and
we always want to handle errors better, if possible. Also DRIVER_VERSION
is not used anymore these days.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add SDHCI_QUIRK2_PRESET_VALUE_BROKEN quirk as setting preset values loads
incorrect CLKD values (for UHS modes).

Remove SDHCI_QUIRK2_NO_1_8_V quirk as sdhci-omap now supports UHS modes.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The data manual of J6/J6 Eco recommends to set different IODELAY values
depending on the mode in which the MMC/SD is enumerated in order to
ensure IO timings are met.

Add support to set the IODELAY values depending on the various MMC
modes using the pinctrl APIs.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Errata i802 in AM572x Sitara Processors Silicon Revision 2.0, 1.1
(SPRZ429K July 2014–Revised March 2017 [1]) mentions
DCRC error interrupts (MMCHS_STAT[21] DCRC=0x1) can occur
during the tuning procedure and it has to be disabled during the
tuning procedure Implement workaround for Errata i802 here..

[1] -> http://www.ti.com/lit/er/sprz429k/sprz429k.pdf



Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

MMC tuning procedure is required to support SD card
UHS1-SDR104 mode and EMMC HS200 mode.

SDR104/HS200 DLL Tuning Procedure for AM572x platform is mentioned
in Figure 25-51. SDR104/HS200 DLL Tuning Procedure of
AM572x Sitara Processors Silicon Revision 2.0, 1.1 TRM
(SPRUHZ6I - October 2014–Revised April 2017 [1]).

The tuning function sdhci_omap_execute_tuning() will only be
called by the MMC/SD core if the corresponding speed modes
are supported by the OMAP silicon which is set in the mmc
host "caps" field.

[1] -> http://www.ti.com/lit/ug/spruhz6i/spruhz6i.pdf



Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

UHS-1 DDR50 and MMC DDR52 mode require DDR bit to be
set in the configuration register (MMCHS_CON). Add
sdhci-omap specific set_uhs_signaling ops to set
this bit. Also while setting the UHSMS bit, clock should be
disabled.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add card_busy host ops in sdhci_omap to check card busy status.

The voltage switching sequence for AM572x platform is mentioned
in Figure 25-48. eMMC/SD/SDIO Power Switching Procedure of
AM572x Sitara Processors Silicon Revision 2.0, 1.1 TRM
(SPRUHZ6I - October 2014–Revised April 2017 [1]).

In the voltage switching sequence, CLKEXTFREE bit in MMCHS_CON
should also be set after switching to 1.8v which is also taken
care in the card_busy ops.

[1] -> http://www.ti.com/lit/ug/spruhz6i/spruhz6i.pdf



Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Updating 'power_mode' in sdhci_omap_init_74_clocks results in
'power_mode' never updated to MMC_POWER_OFF during card
removal. This results in initialization sequence not sent to the
card during re-insertion.
Fix it here by adding sdhci_omap_set_power_mode to update power_mode.
This function can also be used later to perform operations that
are specific to a power mode (e.g, disable tuning during power off).

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Pull x86 fixes from Thomas Gleixner:
 "A small set of fixes for x86:

   - Add missing instruction suffixes to assembly code so it can be
     compiled by newer GAS versions without warnings.

   - Switch refcount WARN exceptions to UD2 as we did in general

   - Make the reboot on Intel Edison platforms work

   - A small documentation update so text and sample command match"

* 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  Documentation, x86, resctrl: Make text and sample command match
  x86/platform/intel-mid: Handle Intel Edison reboot correctly
  x86/asm: Add instruction suffixes to bitops
  x86/entry/64: Add instruction suffix
  x86/refcounts: Switch to UD2 for exceptions

Pull x86/pti fixes from Thomas Gleixner:
 "Three fixes related to melted spectrum:

   - Sync the cpu_entry_area page table to initial_page_table on 32 bit.

     Otherwise suspend/resume fails because resume uses
     initial_page_table and triggers a triple fault when accessing the
     cpu entry area.

   - Zero the SPEC_CTL MRS on XEN before suspend to address a
     shortcoming in the hypervisor.

   - Fix another switch table detection issue in objtool"

* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/cpu_entry_area: Sync cpu_entry_area to initial_page_table
  objtool: Fix another switch table detection issue
  x86/xen: Zero MSR_IA32_SPEC_CTRL before suspend

Pull timer fixes from Thomas Gleixner:
 "A small set of fixes from the timer departement:

   - Add a missing timer wheel clock forward when migrating timers off a
     unplugged CPU to prevent operating on a stale clock base and
     missing timer deadlines.

   - Use the proper shift count to extract data from a register value to
     prevent evaluating unrelated bits

   - Make the error return check in the FSL timer driver work correctly.
     Checking an unsigned variable for less than zero does not really
     work well.

   - Clarify the confusing comments in the ARC timer code"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  timers: Forward timer base before migrating timers
  clocksource/drivers/arc_timer: Update some comments
  clocksource/drivers/mips-gic-timer: Use correct shift count to extract data
  clocksource/drivers/fsl_ftm_timer: Fix error return checking

Pull irq fixlet from Thomas Gleixner:
 "Just a documentation update for the missing device tree property of
  the R-Car M3N interrupt controller"

* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  dt-bindings/irqchip/renesas-irqc: Document R-Car M3-N support

Pull btrfs fixes from David Sterba:

 - when NR_CPUS is large, a SRCU structure can significantly inflate
   size of the main filesystem structure that would not be possible to
   allocate by kmalloc, so the kvalloc fallback is used

 - improved error handling

 - fix endiannes when printing some filesystem attributes via sysfs,
   this is could happen when a filesystem is moved between different
   endianity hosts

 - send fixes: the NO_HOLE mode should not send a write operation for a
   file hole

 - fix log replay for for special files followed by file hardlinks

 - fix log replay failure after unlink and link combination

 - fix max chunk size calculation for DUP allocation

* tag 'for-4.16-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  Btrfs: fix log replay failure after unlink and link combination
  Btrfs: fix log replay failure after linking special file and fsync
  Btrfs: send, fix issuing write op when processing hole in no data mode
  btrfs: use proper endianness accessors for super_copy
  btrfs: alloc_chunk: fix DUP stripe size handling
  btrfs: Handle btrfs_set_extent_delalloc failure in relocate_file_extent_cluster
  btrfs: handle failure of add_pending_csums
  btrfs: use kvzalloc to allocate btrfs_fs_info

Pull i2c fixes from Wolfram Sang:
 "A driver fix and a documentation fix (which makes dependency handling
  for the next cycle easier)"

* 'i2c/for-current-fixed' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: octeon: Prevent error message on bus error
  dt-bindings: at24: sort manufacturers alphabetically

Pull libnvdimm fixes from Dan Williams:
 "A 4.16 regression fix, three fixes for -stable, and a cleanup fix:

   - During the merge window support for the new ACPI NVDIMM Platform
     Capabilities structure disabled support for "deep flush", a
     force-unit- access like mechanism for persistent memory. Restore
     that mechanism.

   - VFIO like RDMA is yet one more memory registration / pinning
     interface that is incompatible with Filesystem-DAX. Disable long
     term pins of Filesystem-DAX mappings via VFIO.

   - The Filesystem-DAX detection to prevent long terms pins mistakenly
     also disabled Device-DAX pins which are not subject to the same
     block- map collision concerns.

   - Similar to the setup path, softlockup warnings can trigger in the
     shutdown path for large persistent memory namespaces. Teach
     for_each_device_pfn() to perform cond_resched() in all cases.

   - Boaz noticed that the might_sleep() in dax_direct_access() is stale
     as of the v4.15 kernel.

  These have received a build success notification from the 0day robot,
  and the longterm pin fixes have appeared in -next. However, I recently
  rebased the tree to remove some other fixes that need to be reworked
  after review feedback.

* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  memremap: fix softlockup reports at teardown
  libnvdimm: re-enable deep flush for pmem devices via fsync()
  vfio: disable filesystem-dax page pinning
  dax: fix vma_is_fsdax() helper
  dax: ->direct_access does not sleep anymore

Merge tag 'kbuild-fixes-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild

Pull Kbuild fixes from Masahiro Yamada:

 - suppress sparse warnings about unknown attributes

 - fix typos and stale comments

 - fix build error of arch/sh

 - fix wrong use of ld-option vs cc-ldoption

 - remove redundant GCC_PLUGINS_CFLAGS assignment

 - fix another memory leak of Kconfig

 - fix line number in error messages of Kconfig

 - do not write confusing CONFIG_DEFCONFIG_LIST out to .config

 - add xstrdup() to Kconfig to handle memory shortage errors

 - show also a Debian package name if ncurses is missing

* tag 'kbuild-fixes-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  MAINTAINERS: take over Kconfig maintainership
  kconfig: fix line number in recursive inclusion error message
  Coccinelle: memdup: Fix typo in warning messages
  kconfig: Update ncurses package names for menuconfig
  kbuild/kallsyms: trivial typo fix
  kbuild: test --build-id linker flag by ld-option instead of cc-ldoption
  kbuild: drop superfluous GCC_PLUGINS_CFLAGS assignment
  kconfig: Don't leak choice names during parsing
  sh: fix build error for empty CONFIG_BUILTIN_DTB_SOURCE
  kconfig: set SYMBOL_AUTO to the symbol marked with defconfig_list
  kconfig: add xstrdup() helper
  kbuild: disable sparse warnings about unknown attributes
  Makefile: Fix lying comment re. silentoldconfig

Pull media fixes from Mauro Carvalho Chehab:

  - some build fixes with randconfigs

  - an m88ds3103 fix to prevent an OOPS if the chip doesn't provide the
    right version during probe (with can happen if the hardware hangs)

  - a potential out of array bounds reference in tvp5150

  - some fixes and improvements in the DVB memory mapped API (added for
    kernel 4.16)

* tag 'media/v4.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
  media: vb2: Makefile: place vb2-trace together with vb2-core
  media: Don't let tvp5150_get_vbi() go out of vbi_ram_default array
  media: dvb: update buffer mmaped flags and frame counter
  media: dvb: add continuity error indicators for memory mapped buffers
  media: dmxdev: Fix the logic that enables DMA mmap support
  media: dmxdev: fix error code for invalid ioctls
  media: m88ds3103: don't call a non-initalized function
  media: au0828: add VIDEO_V4L2 dependency
  media: dvb: fix DVB_MMAP dependency
  media: dvb: fix DVB_MMAP symbol name
  media: videobuf2: fix build issues with vb2-trace
  media: videobuf2: Add VIDEOBUF2_V4L2 Kconfig option for VB2 V4L2 part

Pull watchdog fixes from Wim Van Sebroeck:

 - rave-sp: add NVMEM dependency

 - build fixes for i6300esb_wdt, xen_wdt and sp5100_tco

* tag 'linux-watchdog-4.16-fixes-1' of git://www.linux-watchdog.org/linux-watchdog:
  watchdog: sp5100_tco.c: fix potential build failure
  watchdog: xen_wdt: fix potential build failure
  watchdog: i6300esb: fix build failure
  watchdog: rave-sp: add NVMEM dependency

Pull KVM fixes from Radim Krčmář:
 "x86:

   - fix NULL dereference when using userspace lapic

   - optimize spectre v1 mitigations by allowing guests to use LFENCE

   - make microcode revision configurable to prevent guests from
     unnecessarily blacklisting spectre v2 mitigation feature"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: x86: fix vcpu initialization with userspace lapic
  KVM: X86: Allow userspace to define the microcode version
  KVM: X86: Introduce kvm_get_msr_feature()
  KVM: SVM: Add MSR-based feature support for serializing LFENCE
  KVM: x86: Add a framework for supporting MSR-based features