This adds hrefprev60, hrefv60plus and ccu9540 to device trees compiled
during build.

Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>

GPIO numbers for the newly created gpio-regulator will differ from
board to board. Therefore it's not sensible to leave this information
in the top level DTSI file. Let's move them out to the DTS files
where they can correctly vary.

Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Not all supported boards will require a MMCI gpio-regulator,
therefore it's a good idea to only enable the node when and if
it is required. Let's disable it by default.

Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The u9540 supports 3 MMC devices. This patch enables two of them
and updates the configuration of the already enabled SDI4 port.

Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Here we add the device node for the SDI4 (MMC) port to the u9540
Device Tree source file. This will allow successful probing of
the internal MMC storage device when booting with DT enabled.

Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add the 3 UART nodes required to enable serial ports on the u9540.

Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This patch sees the creation of a sparse Device Tree file for
ST-Ericsson's latest development board supporting the latest
dual-core Cortex-a9 u9540 SoC.

Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Here we add the Device Tree nodes which are required to successfully
probe the MMCI driver which will enable the four cards available on
ST-Ericsson's HREF hardware development platform.

Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Regulator supply names should be allocated by board rather than
per SoC, as the same SoC could be wired differently on varying
hardware. Here we push all regulator-name allocation out to the
dbx5x0 subordinate board files; HREF and Snowball.

Requested-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

On boot the Nomadik GPIO controller complains that an IRQ can't be
configured as active high level-sensitive, so this patch converts
it to be low-to-high edge triggered instead.

Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

There is a very simple mechanism to change and SDI's voltage which
consists of toggling some GPIOs. This scenario can be better handled
if we convert it to a GPIO regulator. This patch provides one which
can be read from Device Tree.

Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

So far, each ST-Ericsson board supported by Device Tree has been similar
enough to run though a single DT_MACHINE_INIT call. On the back of that
it has been suggested that we should reduce the number of compatible
strings in our dt_compat structure. After subsequent discussion with Arnd
Bergmann the conclusion was to list entries by platform as opposed to by
board.

The other suggestion was to use a single string which would cover all
supported platforms, but any wildcard entries would include unsupported
chipsets, such as the u5500 and potential new chips which no not yet have
DT functionality. Hence, the best solution which encompasses all supported
platforms, but no unsupported ones was to list the currently enabled four
chipsets; u8500, u8540, u9500 and u9540 instead.

Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

When enabling ST-Ericsson's ccu9540 development board the board's
full name has not been used. This patch adapts all references of
the board's short name to how it should be referenced.

Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The u9540 supports 3 MMC devices. This patch enables two of them
and updates the configuration of the already enabled SDI4 port.

Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Here we add the device node for the SDI4 (MMC) port to the u9540
Device Tree source file. This will allow successful probing of
the internal MMC storage device when booting with DT enabled.

Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add the 3 UART nodes required to enable serial ports on the u9540.

Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This patch sees the creation of a sparse Device Tree file for
ST-Ericsson's latest development board supporting the latest
dual-core Cortex-a9 u9540 SoC.

Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This patch allows the STMPE keypad driver to be successfully probed
and initialised during a Device Tree enabled boot sequence. It
contains all of the required properties needed to setup and map
each key on the 6x3 keypad located on the ST User Interface Board.

Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Here we apply the STMPE Multi-Functional Device's node to the
ST User Interface Board Device Tree file. It includes all of
the properties required for correct device initialsation.

Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

It is possible to connect a BU21013 Touch Screen to all version
of the HREF which support the ST-UIB. This patch applies all the
necessary settings to the pre-v60 and v60+ HREF Device Trees.

Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This is a skeleton creation which will be populated with the devices
found on one of ST-Ericsson's (UIB) User Interface Board.

Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Here we ensure the SFH7741 Proximity Sensor is registered through
gpio-keys when booting with Device Tree enabled.

Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

In ux500 platform code we currently support a number of devices.
Two of these devices are fairly similar, but have key differences.
Early (pre-v60) HREFs and the more up-to-date versions (v60+), and
they both need to be supported by Device Tree. Here we apply a DT
source file for the earlier versions.

Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

There are two main versions of the ST-Ericsson hardware reference board,
each with subtle differences. These versions are described in current
platform data as 'mop500' for HREF v1.1 & v2.0 and 'hrefv60+' for latter
incarnations. However, the boards have much in common, so this patch
creates a .dtsi (Device Tree Source Include) file which describes the
similarities between the two boards and individual 'hrefprev60' and
'hrefv60plus' .dts files which depict the differences.

Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Snowball's external SD/MMC slot is only capable of 4 bit data
transfer, not 8 bits as previously thought. This is a simple
fixup moving to the correct settings.

Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Here we add the Device Tree nodes which are required to successfully
probe the MMCI driver which will enable the four cards available on
ST-Ericsson's HREF hardware development platform.

Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

In the DB8500 Reference Manual SDI devices are described as being
part of peripheral blocks. This is more in line with how these devices
are actually represented in hardware, so here we detail which
peripheral block each of the SDI devices belong in the node name.

Requested-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Regulator supply names should be allocated by board rather than
per SoC, as the same SoC could be wired differently on varying
hardware. Here we push all regulator-name allocation out to the
dbx5x0 subordinate board files; HREF and Snowball.

Requested-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The current DT nodes for mx23/mx28 miss the `clocks-names` item for gpmi-nand.
So the gpmi-nand driver could not find the proper clock.

This patch fixes this issue.

Signed-off-by: Huang Shijie <b32955@freescale.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Here we fix a simple copy and paste error and bring some node
spaces back into line with the remainder of the tree.

Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Now the Nomadik I2C driver has been converted to an AMBA one, we
are required to provide the Primecell IDs via platform code. When
booting with DT enabled these have to be specified in the device
nodes. We do that here.

Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Signed-off-by: Marek Belisko <marek.belisko@open-nandra.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Fixes the following errors:
[    2.318084] omap-mcbsp 49022000.mcbsp: invalid rx DMA channel
[    2.324432] omap-mcbsp 49024000.mcbsp: invalid rx DMA channel

Which is because we failed to link the sidetone hwmod for McBSP2/3. The
missing sidetone hwmod link will prevent omap_device_alloc() to append the
DMA resources since we - accidentally - end up having the same number of
resources provided from DT (IO/IRQ) as we have in hwmod for the McBSP ports
without the ST resources.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Change event type to switch for the power and autopower switches.
Additionally, this patch aligns the keycodes with the other linkstation
boards already supported by linux.

Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Don't use the specific board name in a the common device tree include file.
Instead use the common name 'lsxl'.

Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Make use of DT support for the crypto engine on dove and remove
the obsolete init call.

Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

The watchdog on dove requires an interrupt that is not yet
available on DT. Therefore, the watchdog DT node is removed
until the corresponding chained intc is available.

Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

This patch adds proper ranges for all mapped addresses within
dove SoC and moves the interrupt controller node inside the simple-bus
node.

Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

During the review process of dove DT patches, Tauros2 cache
init call was changed and DT support added. This patch fixes
the call to Tauros2 init and adds a DT node. Moreover, plat/irq.h
include was missing from mach-dove/common.c.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

Since the maximum section size on mach-exynos is set to 256MiB, boards
with memory configuration defined using sections bigger than 256MiB will
fail to boot with a kernel panic.

This patch modifies the dts file of Samsung Trats board to define four
sections of 256MiB instead of two of 512MiB to fix the boot problem.

Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>