Since irq request is the last thing in the driver probe, it happens
later than the input device registration. This means that there is a
small time window where if the open method is called the driver will
attempt to enable not yet available irq.

Fix that by moving the irq request before the input device registration.

Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Fixes: 26822652

 ("Input: add zinitix touchscreen driver")
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20220106072840.36851-2-nikita@trvn.ru


Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The spaceball.c module was not properly parsing the movement reports
coming from the device.  The code read axis data as signed 16-bit
little-endian values starting at offset 2.

In fact, axis data in Spaceball movement reports are signed 16-bit
big-endian values starting at offset 3.  This was determined first by
visually inspecting the data packets, and later verified by consulting:
http://spacemice.org/pdf/SpaceBall_2003-3003_Protocol.pdf



If this ever worked properly, it was in the time before Git...

Signed-off-by: Leo L. Schwab <ewhac@ewhac.org>
Link: https://lore.kernel.org/r/20211221101630.1146385-1-ewhac@ewhac.org


Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Syzbot has reported warning in __flush_work(). This warning is caused by
work->func == NULL, which means missing work initialization.

This may happen, since input_dev->close() calls
cancel_work_sync(&dev->work), but dev->work initalization happens _after_
input_register_device() call.

So this patch moves dev->work initialization before registering input
device

Fixes: 5a6eb676

 ("Input: appletouch - improve powersaving for Geyser3 devices")
Reported-and-tested-by:  <syzbot+b88c5eae27386b252bbd@syzkaller.appspotmail.com>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/20211230141151.17300-1-paskripkin@gmail.com


Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The eKTH3900/eKTH5312 series do not support the firmware update rules of
Remark ID. Exclude these two series from checking it when updating the
firmware in touch controllers.

Signed-off-by: Johnny Chuang <johnny.chuang.emc@gmail.com>
Link: https://lore.kernel.org/r/1639619603-20616-1-git-send-email-johnny.chuang.emc@gmail.com


Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The "id_buf" buffer is stored in "data->raw_info_block" and freed by
"mxt_free_object_table" in case of error.

Return instead of jumping to avoid a double free.

Addresses-Coverity-ID: 1474582 ("Double free")
Fixes: 068bdb67

 ("Input: atmel_mxt_ts - fix the firmware update")
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Link: https://lore.kernel.org/r/20211212194257.68879-1-jose.exposito89@gmail.com


Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Addresses-Coverity-ID: 1493934 ("Resource leak")
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Link: https://lore.kernel.org/r/20211208173321.26659-1-jose.exposito89@gmail.com


Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add d->model mapping for the "9111" model, this fixes uses using
a wrong config_len of 240 bytes while the "9111" model uses
only 186 bytes of config.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211206164747.197309-2-hdegoede@redhat.com


Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Unless the controller is not responding at boot or after suspend/resume,
the driver never resets the controller on x86/ACPI platforms. The driver
still requesting the reset pin at probe() though in case it needs it.

Until now the driver has always requested the reset pin with GPIOD_IN
as type. The idea being to put the pin in high-impedance mode to save
power until the driver actually wants to issue a reset.

But this means that just requesting the pin can cause issues, since
requesting it in another mode then GPIOD_ASIS may cause the pinctrl
driver to touch the pin settings. We have already had issues before
due to a bug in the pinctrl-cherryview.c driver which has been fixed in
commit 921daeec ("pinctrl: cherryview: Preserve
CHV_PADCTRL1_INVRXTX_TXDATA flag on GPIOs").

And now it turns out that requesting the reset-pin as GPIOD_IN also stops
the touchscreen from working on the GPD P2 max mini-laptop. The behavior
of putting the pin in high-impedance mode relies on there being some
external pull-up to keep it high and there seems to be no pull-up on the
GPD P2 max, causing things to break.

This commit fixes this by requesting the reset pin as is when using
the x86/ACPI code paths to lookup the GPIOs; and by not dropping it
back into input-mode in case the driver does end up issuing a reset
for error-recovery.

BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=209061
Fixes: a7d4b171

 ("Input: goodix - add support for getting IRQ + reset GPIOs on Cherry Trail devices")
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211206091116.44466-2-hdegoede@redhat.com


Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The ASUS UM325UA suffers from the same issue as the ASUS UX425UA, which
is a very similar laptop. The i8042 device is not usable immediately
after boot and fails to initialize, requiring a deferred retry.

Enable the deferred probe quirk for the UM325UA.

BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1190256


Signed-off-by: Samuel Čavoj <samuel@cavoj.net>
Link: https://lore.kernel.org/r/20211204015615.232948-1-samuel@cavoj.net


Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The array param[] in elantech_change_report_id() must be at least 3
bytes, because elantech_read_reg_params() is calling ps2_command() with
PSMOUSE_CMD_GETINFO, that is going to access 3 bytes from param[], but
it's defined in the stack as an array of 2 bytes, therefore we have a
potential stack out-of-bounds access here, also confirmed by KASAN:

[    6.512374] BUG: KASAN: stack-out-of-bounds in __ps2_command+0x372/0x7e0
[    6.512397] Read of size 1 at addr ffff8881024d77c2 by task kworker/2:1/118

[    6.512416] CPU: 2 PID: 118 Comm: kworker/2:1 Not tainted 5.13.0-22-generic #22+arighi20211110
[    6.512428] Hardware name: LENOVO 20T8000QGE/20T8000QGE, BIOS R1AET32W (1.08 ) 08/14/2020
[    6.512436] Workqueue: events_long serio_handle_event
[    6.512453] Call Trace:
[    6.512462]  show_stack+0x52/0x58
[    6.512474]  dump_stack+0xa1/0xd3
[    6.512487]  print_address_description.constprop.0+0x1d/0x140
[    6.512502]  ? __ps2_command+0x372/0x7e0
[    6.512516]  __kasan_report.cold+0x7d/0x112
[    6.512527]  ? _raw_write_lock_irq+0x20/0xd0
[    6.512539]  ? __ps2_command+0x372/0x7e0
[    6.512552]  kasan_report+0x3c/0x50
[    6.512564]  __asan_load1+0x6a/0x70
[    6.512575]  __ps2_command+0x372/0x7e0
[    6.512589]  ? ps2_drain+0x240/0x240
[    6.512601]  ? dev_printk_emit+0xa2/0xd3
[    6.512612]  ? dev_vprintk_emit+0xc5/0xc5
[    6.512621]  ? __kasan_check_write+0x14/0x20
[    6.512634]  ? mutex_lock+0x8f/0xe0
[    6.512643]  ? __mutex_lock_slowpath+0x20/0x20
[    6.512655]  ps2_command+0x52/0x90
[    6.512670]  elantech_ps2_command+0x4f/0xc0 [psmouse]
[    6.512734]  elantech_change_report_id+0x1e6/0x256 [psmouse]
[    6.512799]  ? elantech_report_trackpoint.constprop.0.cold+0xd/0xd [psmouse]
[    6.512863]  ? ps2_command+0x7f/0x90
[    6.512877]  elantech_query_info.cold+0x6bd/0x9ed [psmouse]
[    6.512943]  ? elantech_setup_ps2+0x460/0x460 [psmouse]
[    6.513005]  ? psmouse_reset+0x69/0xb0 [psmouse]
[    6.513064]  ? psmouse_attr_set_helper+0x2a0/0x2a0 [psmouse]
[    6.513122]  ? phys_pmd_init+0x30e/0x521
[    6.513137]  elantech_init+0x8a/0x200 [psmouse]
[    6.513200]  ? elantech_init_ps2+0xf0/0xf0 [psmouse]
[    6.513249]  ? elantech_query_info+0x440/0x440 [psmouse]
[    6.513296]  ? synaptics_send_cmd+0x60/0x60 [psmouse]
[    6.513342]  ? elantech_query_info+0x440/0x440 [psmouse]
[    6.513388]  ? psmouse_try_protocol+0x11e/0x170 [psmouse]
[    6.513432]  psmouse_extensions+0x65d/0x6e0 [psmouse]
[    6.513476]  ? psmouse_try_protocol+0x170/0x170 [psmouse]
[    6.513519]  ? mutex_unlock+0x22/0x40
[    6.513526]  ? ps2_command+0x7f/0x90
[    6.513536]  ? psmouse_probe+0xa3/0xf0 [psmouse]
[    6.513580]  psmouse_switch_protocol+0x27d/0x2e0 [psmouse]
[    6.513624]  psmouse_connect+0x272/0x530 [psmouse]
[    6.513669]  serio_driver_probe+0x55/0x70
[    6.513679]  really_probe+0x190/0x720
[    6.513689]  driver_probe_device+0x160/0x1f0
[    6.513697]  device_driver_attach+0x119/0x130
[    6.513705]  ? device_driver_attach+0x130/0x130
[    6.513713]  __driver_attach+0xe7/0x1a0
[    6.513720]  ? device_driver_attach+0x130/0x130
[    6.513728]  bus_for_each_dev+0xfb/0x150
[    6.513738]  ? subsys_dev_iter_exit+0x10/0x10
[    6.513748]  ? _raw_write_unlock_bh+0x30/0x30
[    6.513757]  driver_attach+0x2d/0x40
[    6.513764]  serio_handle_event+0x199/0x3d0
[    6.513775]  process_one_work+0x471/0x740
[    6.513785]  worker_thread+0x2d2/0x790
[    6.513794]  ? process_one_work+0x740/0x740
[    6.513802]  kthread+0x1b4/0x1e0
[    6.513809]  ? set_kthread_struct+0x80/0x80
[    6.513816]  ret_from_fork+0x22/0x30

[    6.513832] The buggy address belongs to the page:
[    6.513838] page:00000000bc35e189 refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x1024d7
[    6.513847] flags: 0x17ffffc0000000(node=0|zone=2|lastcpupid=0x1fffff)
[    6.513860] raw: 0017ffffc0000000 dead000000000100 dead000000000122 0000000000000000
[    6.513867] raw: 0000000000000000 0000000000000000 00000000ffffffff 0000000000000000
[    6.513872] page dumped because: kasan: bad access detected

[    6.513879] addr ffff8881024d77c2 is located in stack of task kworker/2:1/118 at offset 34 in frame:
[    6.513887]  elantech_change_report_id+0x0/0x256 [psmouse]

[    6.513941] this frame has 1 object:
[    6.513947]  [32, 34) 'param'

[    6.513956] Memory state around the buggy address:
[    6.513962]  ffff8881024d7680: f2 f2 f2 f2 f2 00 00 f3 f3 00 00 00 00 00 00 00
[    6.513969]  ffff8881024d7700: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[    6.513976] >ffff8881024d7780: 00 00 00 00 f1 f1 f1 f1 02 f3 f3 f3 00 00 00 00
[    6.513982]                                            ^
[    6.513988]  ffff8881024d7800: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[    6.513995]  ffff8881024d7880: 00 f1 f1 f1 f1 03 f2 03 f2 03 f3 f3 f3 00 00 00
[    6.514000] ==================================================================

Define param[] in elantech_change_report_id() as an array of 3 bytes to
prevent the out-of-bounds access in the stack.

Fixes: e4c90627 ("Input: elantech - fix protocol errors for some trackpoints in SMBus mode")
BugLink: https://bugs.launchpad.net/bugs/1945590


Signed-off-by: Andrea Righi <andrea.righi@canonical.com>
Reviewed-by: Wolfram Sang <wsa@kernel.org>
Link: https://lore.kernel.org/r/20211116095559.24395-1-andrea.righi@canonical.com


Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Some automated builds report a stack frame size in excess of 2 kB for
iqs626_probe(); the culprit appears to be the call to iqs626_parse_prop().

To solve this problem, specify noinline_for_stack for all of the
iqs626_parse_*() helper functions which are called inside a for loop
within iqs626_parse_prop().

As a result, a build with '-Wframe-larger-than' as low as 512 is free of
any such warnings.

Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/20211129004104.453930-1-jeff@labundy.com


Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

We've got a bug report about the non-working keyboard on ASUS ZenBook
UX425UA.  It seems that the PS/2 device isn't ready immediately at
boot but takes some seconds to get ready.  Until now, the only
workaround is to defer the probe, but it's available only when the
driver is a module.  However, many distros, including openSUSE as in
the original report, build the PS/2 input drivers into kernel, hence
it won't work easily.

This patch adds the support for the deferred probe for i8042 stuff as
a workaround of the problem above.  When the deferred probe mode is
enabled and the device couldn't be probed, it'll be repeated with the
standard deferred probe mechanism.

The deferred probe mode is enabled either via the new option
i8042.probe_defer or via the quirk table entry.  As of this patch, the
quirk table contains only ASUS ZenBook UX425UA.

The deferred probe part is based on Fabio's initial work.

BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1190256


Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Samuel Čavoj <samuel@cavoj.net>
Link: https://lore.kernel.org/r/20211117063757.11380-1-tiwai@suse.de



Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Prepare input updates for 5.16 merge window.

USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.

Fixes: 48735862

 ("Input: iforce - use DMA-safe buffer when getting IDs from USB")
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: stable@vger.kernel.org      # 5.3
Link: https://lore.kernel.org/r/20211025115501.5190-1-johan@kernel.org


Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

To make the code easier to read use macros for the bit masks.

Signed-off-by: Alistair Francis <alistair@alistair23.me>
Link: https://lore.kernel.org/r/20211009113707.17568-2-alistair@alistair23.me


Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Modern devices may redraw display at 60 Hz, make sure we have one input
sample per one frame. Reduce sample period to 15ms, so we would get up
to 66.6 samples per second, although realistically with all the jitter
and extra scheduling wiggle room, we would end up just above 60 samples
per second. This should be a good compromise between sampling too often
and sampling too seldom.

Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20211108114145.84118-1-marex@denx.de


Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Currently the ili210x driver implements a threaded interrupt handler which
starts upon edge on the interrupt line, and then polls the touch controller
for samples. Every time a sample is obtained from the controller, the thread
function checks whether further polling is required, and if so, waits fixed
amount of time before polling for next sample.

The delay between consecutive samples can thus vary greatly, because the
I2C transfer required to retrieve the sample from the controller takes
different amount of time on different platforms. Furthermore, different
models of the touch controllers supported by this driver require different
delays during retrieval of samples too.

Instead of waiting fixed amount of time before polling for next sample,
determine how much time passed since the beginning of sampling cycle and
then wait only the remaining amount of time within the sampling cycle.
This makes the driver deliver samples with equal spacing between them.

Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20211108005216.480525-1-marex@denx.de


Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The ili251x touch controller needs 5ms delay between sending I2C device
address and register address, and, writing or reading register data.

According to downstream ili251x example code, this 5ms delay is not
required when reading touch samples out of the controller. Implement
such a special case.

Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20211108005259.480545-1-marex@denx.de


Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Some firmwares occasionally report bogus data from trackpoint, with X or Y
displacement being too large (outside of [-127, 127] range). Let's drop such
packets so that we do not generate jumps.

Signed-off-by: Phoenix Huang <phoenix@emc.com.tw>
Tested-by: Yufei Du <yufeidu@cs.unc.edu>
Link: https://lore.kernel.org/r/20210729010940.5752-1-phoenix@emc.com.tw


Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The created rmi device is orphan, which breaks the real device
hierarchy, and can cause some trouble, especially during suspend
and resume sequences. E.g. in case of I2C, rmi dev should be child
of the I2C client device.

Fix this, assigning the transport device as parent of the rmi device.

Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Link: https://lore.kernel.org/r/1635514971-18415-1-git-send-email-loic.poulain@linaro.org


Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Fujitsu Lifebook T725 laptop requires, like a few other similar
models, the nomux and notimeout options to probe the touchpad
properly.  This patch adds the corresponding quirk entries.

BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1191980


Tested-by: Neal Gompa <ngompa13@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20211103070019.13374-1-tiwai@suse.de


Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

According to the datasheet "The CAP1206 is pin- and register-compatible
with the CAP1106, with the exception of the GAIN[1:0] bits and ALT_POL
bit"(57). So, this patch aims to disable them as they are no longer
used.

Signed-off-by: Jesse Taube <mr.bossman075@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Commit 83b41248

 ("Input: cy8ctmg110_ts - switch to using gpiod API")
remove the last use of <linux/input/cy8ctmg110_pdata.h> but left the header
file behind.  Nothing uses it now, delete it.

Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/20211102220203.940290-6-corbet@lwn.net


Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The ili251x firmware can be updated, this is used when switching between
different modes of operation of the touch surface, e.g. glove operation.
This patch implements the firmware update mechanism triggered by a write
into an sysfs attribute.

The firmware itself is distributed as an intel hex file with non-standard
types. The first two lines are of type 0xad, which indicates the start of
DataFlash payload, that is always at address 0xf000 on the ili251x, so it
can be dropped, and 0xac which indicates the position of firmware info in
the Application payload, that is always at address 0x2020 on the ili251x
and we do not care. The rest of the firmware is data of type 0x00, and we
care about that. To convert the firmware hex file into something usable
by the kernel, remove the first two lines and then use ihex2fw:

 $ tail -n +3 input.hex > temp.hex
 $ ./tools/firmware/ihex2fw temp.hex firmware/ilitek/ili251x.bin

To trigger the firmware update, place firmware file ilitek/ili251x.bin
into /lib/firmware/, write into firmware_update sysfs attribute and wait
about 30-40 seconds. The firmware update is slow. Afterward, verify the
firmware_version and mode sysfs attributes to check whether the firmware
got updated and the controller switched back to application (AP) mode by
reading out 'mode' attribute in sysfs.

Note that the content of firmware_version, e.g. 0600.0005.abcd.aa04 can
be matched to the content of the firmware hex file. The first four bytes,
0x06 0x00 0x00 0x05 can be found at ^:102030 00 05000006, the next four
bytes 0xab 0xcd 0xaa 0x04 at ^:10F000 00 nnnnnnnn ABCDAA04.

Note that the protocol differs considerably between the ili2xxx devices,
this patch therefore implements this functionality only for ili251x that
I can test.

Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20210831202506.181927-3-marex@denx.de


Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The ili251x firmware protocol permits readout of firmware version,
protocol version, mcu version and current mode (application, boot
loader, forced update). These information are useful when updating
the firmware on the il251x, e.g. to avoid updating the same firmware
into the device multiple times. The locking is now necessary to avoid
races between interrupt handler and the sysfs readouts.

Note that the protocol differs considerably between the ili2xxx devices,
this patch therefore implements this functionality only for ili251x that
I can test.

Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20210831202506.181927-2-marex@denx.de


Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The ili251x firmware protocol permits readout of panel resolution,
implement this, but make it possible to override this value using
DT bindings. This way, older DTs which contain touchscreen-size-x
and touchscreen-size-y properties will behave just like before and
new DTs may avoid specifying these for ILI251x.

Note that the command format is different on other controllers, so
this functionality is isolated to ILI251x.

Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20210831202506.181927-1-marex@denx.de


Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

On some devices, e.g. Sony Xperia M4 Aqua, warm reset is used to reboot
device into bootloader and recovery mode.  Instead of always doing hard
reset, add a check on reboot_mode for possible warm reset.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Link: https://lore.kernel.org/r/20210714095850.27185-3-shawn.guo@linaro.org


Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Some drivers like Qualcomm pm8941-pwrkey need to access 'reboot_mode'
for triggering reboot between cold and warm mode.  Export the symbol, so
that drivers built as module can still access the symbol.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20210714095850.27185-2-shawn.guo@linaro.org


Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The MODULE_DEVICE_TABLE already creates proper alias for platform
driver.  Having another MODULE_ALIAS causes the alias to be duplicated.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210916170514.137977-1-krzysztof.kozlowski@canonical.com


Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

We are using devm_input_allocate_device() that already sets parent
of the input device, there is no need to do that again.

Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/YWpiZqrfC9+GQsM4@google.com


Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

A new warning in clang points out a few places in this driver where a
bitwise OR is being used with boolean types:

drivers/input/touchscreen.c:81:17: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
        data_present = touchscreen_get_prop_u32(dev, "touchscreen-min-x",
                       ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

This use of a bitwise OR is intentional, as bitwise operations do not
short circuit, which allows all the calls to touchscreen_get_prop_u32()
to happen so that the last parameter is initialized while coalescing the
results of the calls to make a decision after they are all evaluated.

To make this clearer to the compiler, use the '|=' operator to assign
the result of each touchscreen_get_prop_u32() call to data_present,
which keeps the meaning of the code the same but makes it obvious that
every one of these calls is expected to happen.

Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20211014205757.3474635-1-nathan@kernel.org


Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The Nacon GX100XF is already mapped, but it seems there is a Nacon
GC-100 (identified as NC5136Wht PCGC-100WHITE though I believe other
colours exist) with a different USB ID when in XInput mode.

Signed-off-by: Michael Cullen <michael@michaelcullen.name>
Link: https://lore.kernel.org/r/20211015192051.5196-1-michael@michaelcullen.name


Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

For proper pressure calculation we need at least x and z1 to be non
zero. Even worse, in case z1 we may run in to division by zero
error.

Fixes: 60b7db91

 ("Input: resistive-adc-touch - rework mapping of channels")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20211007095727.29579-1-o.rempel@pengutronix.de


Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

On i.MX7S and i.MX8M* (but not i.MX6*) the pwrkey device has an
associated clock. Accessing the registers requires that this clock is
enabled. Binding the driver on at least i.MX7S and i.MX8MP while not
having the clock enabled results in a complete hang of the machine.
(This usually only happens if snvs_pwrkey is built as a module and the
rtc-snvs driver isn't already bound because at bootup the required clk
is on and only gets disabled when the clk framework disables unused clks
late during boot.)

This completes the fix in commit 135be16d

 ("ARM: dts: imx7s: add
snvs clock to pwrkey").

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20211013062848.2667192-1-u.kleine-koenig@pengutronix.de


Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Change the comment to a normal (non-kernel-doc) comment to avoid
these kernel-doc warnings:

max8925_onkey.c:2: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
 * MAX8925 ONKEY driver
max8925_onkey.c:2: warning: missing initial short description on line:
 * MAX8925 ONKEY driver

Fixes: 3734574c

 ("Input: enable onkey driver of max8925")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20211002045943.9406-1-rdunlap@infradead.org


Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

When request_irq() returns -EPORBE_DEFER we should abort probe and try
again later instead of trying to engage IRQ trigger workaround.

Link: https://lore.kernel.org/r/20210910045039.4020199-3-dmitry.torokhov@gmail.com


Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Instead of manipulating capability bits directly use
input_set_capability(). Also stop setting EV_ABS explicitly as
input_set_abs_params() does it for us.

Link: https://lore.kernel.org/r/20210910045039.4020199-2-dmitry.torokhov@gmail.com


Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Set input device's bus type as BUS_SPI and use model as product ID.

Link: https://lore.kernel.org/r/20210910045039.4020199-1-dmitry.torokhov@gmail.com


Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

At the moment the touch keys have key codes assigned from the device
tree. In some cases, users might want to change the key code from
userspace. There is existing functionality for this in the input core
using the EVIOCSKEYCODE ioctl, which is integrated for example into udev.

Make it possible to use this functionality for tm2-touchkey by simply
making the input core aware of the array that holds the keycodes.
Similar code also exists in mcs_touchkey and mpr121_touchkey.

Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20211013112305.41574-2-stephan@gerhold.net


Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Report the index of pressed touch key as MSC_SCAN code to userspace
so it is possible to identify which of the keys was pressed (not
just the function that is currently assigned to the key).

This is done similarly also in mcs_touchkey and mpr121_touchkey.

Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20211013112305.41574-1-stephan@gerhold.net


Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>