ISEE IGEPv2 is an TI OMAP3 SoC based embedded board.

This patch adds an initial device tree support to boot
an IGEPv2 from the MMC/SD.

Currently is working everything that is supported by DT
on OMAP3 SoCs (MMC/SD, GPIO LEDs, EEPROM, TWL4030 audio).

Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Enric Balletbo i Serra <eballetbo@gmail.com>
[benoit.cousson@linaro.org: Update the Makefile for 3.8-rc2]
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>

Add a generic .dtsi device tree source file for the
common characteristics across IGEP Technology devices.

Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Tested-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>

Rename I2C and GPIO nodes according to AM33XX TRM. According to
AM33XX TRM device instances are starting from "0" like i2c0, i2c1
and i2c3.

Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
[panto@antoniou-consulting.com: initial patch by pantelis's]
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>

Merge tag 'omap-devel-b-for-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into for_3.10/dts_merged

Provide RESET and Power regulators for the USB PHY,
the USB Host port mode and the PHY device.

Also provide pin multiplexer information for USB host
pins.

CC: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Adds device nodes for HS USB Host module, TLL module,
OHCI and EHCI controllers.

CC: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Adds device nodes for HS USB Host module, TLL module,
OHCI and EHCI controllers.

CC: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Use usbhs_init_phys() to register the PHY's RESET regulator
and the NOP PHY device.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Use usbhs_init_phys() to register the PHY's RESET regulator
and the NOP PHY device.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Use usbhs_init_phys() to register the PHY's RESET regulator
and the NOP PHY device.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Use usbhs_init_phys() to register the PHY's RESET regulator
and the NOP PHY device.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Use usbhs_init_phys() to register the PHY's RESET regulator
and NOP PHY device. VAUX2 supplies the PHY's VCC.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Use usbhs_init_phys() to register the PHY's RESET regulator
and the NOP PHY device. VAUX2 supplies the PHY's VCC.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Use usbhs_init_phys() to register the PHY's RESET regulators
and the NOP PHY devices.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Remove deprecated USBHS platform data.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Use usbhs_init_phys() to register the PHY's RESET regulators
and the NOP PHY devices.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Use usbhs_init_phys() to register the PHY's RESET regulators
and the NOP PHY devices.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Use usbhs_init_phys() to register the PHY's RESET regulators
and the NOP PHY device.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Use usbhs_init_phys() to register the PHY's VCC and RESET
regulators and the NOP PHY device.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Use usbhs_init_phys() to register the PHY's RESET regulators
and the NOP PHY devices.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Use usbhs_init_phys() to register the PHY's RESET regulators
and the NOP PHY devices.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Use usbhs_init_phys() to register the PHY's VCC and RESET
regulators and the NOP PHY device.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Use usbhs_init_phys() to register the PHY's VCC and RESET
regulators and the NOP PHY device.

Get rid of managing the PHY clock as it will be done by the PHY driver.
For that to work we create a clock alias that links the PHY clock name
to the PHY device name.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This helper allows board support code to add the PHY's
VCC and RESET regulators which are GPIO controlled as well
as the NOP PHY device.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

omap3_noncore_dpll_set_rate() attempts an enable of bypass clk as well
as ref clk for every .set_rate attempt on a noncore DPLL, regardless of
whether the .set_rate results in the DPLL being locked or put in bypass.
Early at boot, while some of these DPLLs are programmed and locked
(using .set_rate for the DPLL), this causes an ordering issue.

For instance, on OMAP5, the USB DPLL derives its bypass clk from ABE DPLL.
If a .set_rate of USB DPLL which programmes the M,N and locks it is called
before the one for ABE, the enable of USB bypass clk (derived from ABE DPLL)
then attempts to lock the ABE DPLL and fails as the M,N values for ABE
are yet to be programmed.

To get rid of this ordering needs, enable bypass clk for a DPLL as part
of its .set_rate only when its being put in bypass, and only enable the
ref clk when its locked.

Reported-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

_pwrdm_save_clkdm_state_and_activate() tried to test one of its
unsigned arguments to determine whether it was less than zero.  Fix by
moving the error test to the caller.

Reported-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

_HWMOD_WAKEUP_ENABLED is currently unused across the hwmod
framework. Just get rid of it, so we have one less flag to
worry about.

Tested-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

WDT1 module can take one of the below clocks as input functional
clock -
     - On-Chip 32K RC Osc [default/reset]
     - 32K from PRCM

The On-Chip 32K RC Osc clock is not an accurate clock-source as per
the design/spec, so as a result, for example, timer which supposed
to get expired @60Sec, but will expire somewhere ~@40Sec, which is
not expected by any use-case.

The solution here is to switch the input clock-source to PRCM
generated 32K clock-source during boot-time itself.

Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Benoit Cousson <benoit.cousson@linaro.org>
Cc: Paul Walmsley <paul@pwsan.com>

This patch adds sysc definitions to the wdt1 hwmod entry, which in-turn
makes sure that sysc idle bit-fields are configured to valid state on
enable/disable callbacks.

With the recent submitted patch from Santosh Shilimkar,
"ARM: OMAP2+: hwmod: Don't call _init_mpu_rt_base if no sysc"
(commit: 4a98c2d89), it is required to add sysconf
information to each valid hwmod entry, else device will not be
come out from idle state properly and leads to below kernel
crash  -

[2.190237] Unhandled fault: external abort on non-linefetch (0x1028) at
0xf9e35034
[2.198325] Internal error: : 1028 [#1] SMP ARM
[2.203101] Modules linked in:
[2.206334] CPU: 0    Not tainted  (3.9.0-rc3-00059-gd114294#1)
[2.212679] PC is at omap_wdt_disable.clone.5+0xc/0x60
[2.218090] LR is at omap_wdt_probe+0x184/0x1fc

Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Benoit Cousson <benoit.cousson@linaro.org>
Cc: Paul Walmsley <paul@pwsan.com>

Pull slave-dmaengine fixes from Vinod Koul:
 "Two fixes for slave-dmaengine.

  The first one is for making slave_id value correct for dw_dmac and
  the other one fixes the endieness in DT parsing"

* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
  dw_dmac: adjust slave_id accordingly to request line base
  dmaengine: dw_dma: fix endianess for DT xlate function

Pull media fixes from Mauro Carvalho Chehab:
 "For a some fixes for Kernel 3.9:
   - subsystem build fix when VIDEO_DEV=y, VIDEO_V4L2=m and I2C=m
   - compilation fix for arm multiarch preventing IR_RX51 to be selected
   - regression fix at bttv crop logic
   - s5p-mfc/m5mols/exynos: a few fixes for cameras on exynos hardware"

* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
  [media] [REGRESSION] bt8xx: Fix too large height in cropcap
  [media] fix compilation with both V4L2 and I2C as 'm'
  [media] m5mols: Fix bug in stream on handler
  [media] s5p-fimc: Do not attempt to disable not enabled media pipeline
  [media] s5p-mfc: Fix encoder control 15 issue
  [media] s5p-mfc: Fix frame skip bug
  [media] s5p-fimc: send valid m2m ctx to fimc_m2m_job_finish
  [media] exynos-gsc: send valid m2m ctx to gsc_m2m_job_finish
  [media] fimc-lite: Fix the variable type to avoid possible crash
  [media] fimc-lite: Initialize 'step' field in fimc_lite_ctrl structure
  [media] ir: IR_RX51 only works on OMAP2

Pull block fixes from Jens Axboe:
 "Alright, this time from 10K up in the air.

  Collection of fixes that have been queued up since the merge window
  opened, hence postponed until later in the cycle.  The pull request
  contains:

   - A bunch of fixes for the xen blk front/back driver.

   - A round of fixes for the new IBM RamSan driver, fixing various
     nasty issues.

   - Fixes for multiple drives from Wei Yongjun, bad handling of return
     values and wrong pointer math.

   - A fix for loop properly killing partitions when being detached."

* tag 'for-linus-20130331' of git://git.kernel.dk/linux-block: (25 commits)
  mg_disk: fix error return code in mg_probe()
  rsxx: remove unused variable
  rsxx: enable error return of rsxx_eeh_save_issued_dmas()
  block: removes dynamic allocation on stack
  Block: blk-flush: Fixed indent code style
  cciss: fix invalid use of sizeof in cciss_find_cfgtables()
  loop: cleanup partitions when detaching loop device
  loop: fix error return code in loop_add()
  mtip32xx: fix error return code in mtip_pci_probe()
  xen-blkfront: remove frame list from blk_shadow
  xen-blkfront: pre-allocate pages for requests
  xen-blkback: don't store dev_bus_addr
  xen-blkfront: switch from llist to list
  xen-blkback: fix foreach_grant_safe to handle empty lists
  xen-blkfront: replace kmalloc and then memcpy with kmemdup
  xen-blkback: fix dispatch_rw_block_io() error path
  rsxx: fix missing unlock on error return in rsxx_eeh_remap_dmas()
  Adding in EEH support to the IBM FlashSystem 70/80 device driver
  block: IBM RamSan 70/80 error message bug fix.
  block: IBM RamSan 70/80 branding changes.
  ...

This reverts commit 6aa97070.

Commit 6aa97070 ("lockdep: check that no locks held at freeze time")
causes problems with NFS root filesystems.  The failures were noticed on
OMAP2 and 3 boards during kernel init:

  [ BUG: swapper/0/1 still has locks held! ]
  3.9.0-rc3-00344-ga937536 #1 Not tainted
  -------------------------------------
  1 lock held by swapper/0/1:
   #0:  (&type->s_umount_key#13/1){+.+.+.}, at: [<c011e84c>] sget+0x248/0x574

  stack backtrace:
    rpc_wait_bit_killable
    __wait_on_bit
    out_of_line_wait_on_bit
    __rpc_execute
    rpc_run_task
    rpc_call_sync
    nfs_proc_get_root
    nfs_get_root
    nfs_fs_mount_common
    nfs_try_mount
    nfs_fs_mount
    mount_fs
    vfs_kern_mount
    do_mount
    sys_mount
    do_mount_root
    mount_root
    prepare_namespace
    kernel_init_freeable
    kernel_init

Although the rootfs mounts, the system is unstable.  Here's a transcript
from a PM test:

  http://www.pwsan.com/omap/testlogs/test_v3.9-rc3/20130317194234/pm/37xxevm/37xxevm_log.txt

Here's what the test log should look like:

  http://www.pwsan.com/omap/testlogs/test_v3.8/20130218214403/pm/37xxevm/37xxevm_log.txt

Mailing list discussion is here:

  http://lkml.org/lkml/2013/3/4/221



Deal with this for v3.9 by reverting the problem commit, until folks can
figure out the right long-term course of action.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Mandeep Singh Baines <msb@chromium.org>
Cc: Jeff Layton <jlayton@redhat.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: <maciej.rutecki@gmail.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ben Chan <benchan@chromium.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull SCSI target fixes from Nicholas Bellinger:
 "This includes the bug-fix for a >= v3.8-rc1 regression specific to
  iscsi-target persistent reservation conflict handling (CC'ed to
  stable), and a tcm_vhost patch to drop VIRTIO_RING_F_EVENT_IDX usage
  so that in-flight qemu vhost-scsi-pci device code can detect the
  proper vhost feature bits.

  Also, there are two more tcm_vhost patches still being discussed by
  MST and Asias for v3.9 that will be required for the in-flight qemu
  vhost-scsi-pci device patch to function properly, and that should
  (hopefully) be the last target fixes for this round."

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  target: Fix RESERVATION_CONFLICT status regression for iscsi-target special case
  tcm_vhost: Avoid VIRTIO_RING_F_EVENT_IDX feature bit

On some hardware configurations we have got the request line with the offset.
The patch introduces convert_slave_id() helper for that cases. The request line
base is came from the driver data provided by the platform_device_id table.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

As reported by Wu Fengguang's build robot tracking sparse warnings, the
dma_spec arguments in the dw_dma_xlate are already byte swapped on
little-endian platforms and must not get swapped again. This code is
currently not used anywhere, but will be used in Linux 3.10 when the
ARM SPEAr platform starts using the generic DMA DT binding.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

The Adam Belay's e-mail address in MAINTAINERS under PNP SUPPORT
is not valid any more and I started to maintain that code in the
meantime as a matter of fact, so list myself as a maintainer of it
along with Bjorn and remove the Adam's entry from it.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull ceph fix from Sage Weil:
 "This fixes a regression introduced during the last merge window when
  mapping non-existent images."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  rbd: don't zero-fill non-image object requests

A result of ENOENT from a read request for an object that's part of
an rbd image indicates that there is a hole in that portion of the
image.  Similarly, a short read for such an object indicates that
the remainder of the read should be interpreted a full read with
zeros filling out the end of the request.

This behavior is not correct for objects that are not backing rbd
image data.  Currently rbd_img_obj_request_callback() assumes it
should be done for all objects.

Change rbd_img_obj_request_callback() so it only does this zeroing
for image objects.  Encapsulate that special handling in its own
function.  Add an assertion that the image object request is a bio
request, since we assume that (and we currently don't support any
other types).

This resolves a problem identified here:
    http://tracker.ceph.com/issues/4559

The regression was introduced by bf0d5f50

.

Reported-by: Dan van der Ster <dan@vanderster.com>
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-off-by: Sage Weil <sage@inktank.com>