Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

DRA72-EVM now has an upgrade to Rev C with SR2.0 silicon. As part of
this change, a few updates were factored in that were software
incompatible with previous board in few areas:
- We now use DP83867 ethernet phy instead of older DP838865 which fails
  in certain use cases.
- Two Ethernet ports now instead of the single one in rev B.
- polarities changed for certain pcf gpios
- Due to SoC phy current requirements, VDDA supplies are split between
 ldo3 and ldo2 (ldo2 was previously unused). NOTE: DSS (VDDA_VIDEO) is
 still supplied by ldo5, HDMI is now supplied by LDO2 instead of using
 LDO3.

NOTE: It does not make much sense to spin off a new board compatible
flag since there is no real benefit for the same.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The Amazon Kindle Fire (first generation) codename kc1 is a tablet that was
released by Amazon back in 2011. It is using an OMAP4430 SoC GP version.

This adds devicetree support for the device, with only a few basic features
supported, such as debug uart, i2c and internal emmc.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The AM572x-IDK board is a board based on TI's AM5728 SOC
which has a dual core 1.5GHz A15 processor. This board is a
development platform for the Industrial market with:
- 2GB of DDR3L
- Dual 1Gbps Ethernet
- HDMI,
- PRU-ICSS
- uSD
- 16GB eMMC
- CAN
- RS-485
- PCIe
- USB3.0
- Video Input Port
- Industrial IO port and expansion connector

The link to the data sheet and TRM can be found here:

http://www.ti.com/product/AM5728



This patch creates a common dtsi file that will provide a common board
dtsi file to define the nodes that are common to AM57xx (including the
upcoming AM5718) IDK boards.

Initial support is only for basic peripherals

Signed-off-by: Schuyler Patton <spatton@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

TI's Industrial Communication Engine EVM is a low cost hardware mainly
developed for industrial communication type applications using serial
or Ethernet based interfaces. This platform features TI's AM3359 with
800MHz single core Cortex-A8 processor, 256MB DDR3, 64MB SPI flash,
8MB NOR Flash, mmc, usb, can, dual Ethernet ports.

For more information, look at HW user guide[1], Data manual[2].

Just add basic support for the moment.

[1] http://processors.wiki.ti.com/index.php/AM335x_Industrial_Communication_Engine_EVM_Rev2_1_HW_User_Guide
[2] http://www.ti.com/lit/ds/symlink/am3359.pdf



Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Initial commit for PH1-Pro4 Sanji board support.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Initial commit for PH1-Pro4 Ace board support.

Note:
There are two variants for the amount of DDR memory; 1GB or 2GB.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

The LG Optimus Black codename sniper is a smartphone that was designed and
manufactured by LG Electronics (LGE) and released back in 2011.
It is using an OMAP3630 SoC, GP version.

This adds devicetree support for the device, with only a few basic features
supported, such as debug uart, i2c, internal emmc and external mmc.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add support for Advantech/GE B850v3 board.

Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for Advantech/GE B650v3 board.

Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Add support for Advantech/GE B450v3 board.

Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Uniwest evi is a portable electrical eddy current non-destructive
testing device.

Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This patch adds dts file for imx6qp-sabresd board.

Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This patch adds basic dts file for i.MX6QP-Sbreauto board.

Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

www.engicam.com/en/products/embedded/som/standard/i-core-rqs-m6s-dl-d-q

Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The lamobo-r1 board, sometimes called the BPI-R1 but not labelled as such
on the PCB, is meant as a A20 based router board. As such the board comes
with a built-in switch chip giving it 5 gigabit ethernet ports, and it
has a large empty area on the pcb with mounting holes which will fit a
2.5 inch harddisk. To complete its networking features it has a
Realtek RTL8192CU for WiFi 802.11 b/g/n.

Signed-off-by: Jelle de Jong <jelledejong@powercraft.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add barebones K2G evm dts. This DTS allows the board to boot using a
ram based filesystem.

The technical reference manual for K2G can be found here:
http://www.ti.com/lit/ug/spruhy8/spruhy8.pdf



Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>

Signed-off-by: Lars Persson <larper@axis.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>

This patch adds a dts file to support the Nexus7 2013
device. Its based off of the qcom-apq8064-ifc6410.dts
which is similar hardware.

Also includes some comments and context folded in
from Vinay Simha BN <simhavcs@gmail.com>

Cc: Rob Herring <robh+dt@kernel.org>
Cc: Arnd Bergmann <arnd.bergmann@linaro.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Andy Gross <agross@codeaurora.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Vinay Simha BN <simhavcs@gmail.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Stephen Boyd <stephen.boyd@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

It's pretty similar to the STM32F429, but there are some
subtle changes required to boot successfully.

Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>

This adds basic chip support for Mediatek MT7623.

Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>

Add dts file to support Buffalo Linkstation LS-GL
(a.k.a Buffalo Linkstation Pro/Live), which is marvell orion5x based
3.5" HDD NAS.

Product info:
  - (JPN) http://buffalo.jp/products/catalog/item/l/ls-gl/
  - (ENG) http://www.buffalotech.com/products/network-storage/linkstation/linkstation-pro



This device tree is based on the board file:
  arch/arm/mach-orion5x/kurobox_pro-setup.c
However, that board file also support Kurobox Pro, which is not supported by
device tree yet. So the board file is not removed.

Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

Add dts file to support Buffalo Linkstation LS-QVL,
which is marvell kirkwood based 4-bay 3.5" HDD NAS.
Product info:
  - (JPN) http://buffalo.jp/product/hdd/network/ls-qvl_r5/
  - (ENG) http://www.buffalotech.com/products/network-storage/home-and-small-office/linkstation-pro-quad



Signed-off-by: Mario Lange <mario_lange@gmx.net>
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

LS-WVL/VL are both kirkwood-6282 based NAS devices, which share
many MPP pins. However they are slightly different:
  - LS-WVL is 2-Bay NAS, and LS-VL is only 1-Bay.
  - There're two red LED indicator on LS-WVL to show when HDD fails,
    which is similar to LS-WXL, but there's no such on LS-VL.

So after the split, common part goes into .dtsi file:
  - kirkwood-linkstation-6282.dtsi
while all rest part goes into device specific .dts file:
  - kirkwood-linkstation-lsvl.dts
  - kirkwood-linkstation-lswvl.dts

Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

LS-WXL/WSXL are both kirkwood-6281 based 2-Bay NAS devices, which share
many MPP pins. However they are slightly different:
  - There're two red LED indicator on LS-WXL to show when HDD fails,
    but there's no such on LS-WSXL.
  - There's 4-level speed adjustable FAN on LS-WXL, but not LS-WSXL.

So after the split, common part goes into .dtsi file:
  - kirkwood-linkstation.dtsi
  - kirkwood-linkstation-duo-6281.dtsi
while all rest part goes into device specific .dts file:
  - kirkwood-linkstation-lswsxl.dts
  - kirkwood-linkstation-lswxl.dts

Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

This one is essentially the same as revision 2 B board (with the I2S on
P5 header).

Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
[anholt: Rebased on bcm2835.dtsi -> bcm283x.dtsi change]
Signed-off-by: Eric Anholt <eric@anholt.net>

The Itead Ibox is a multi board device based on the Allwinner A20 SoC.
It contains the A20 Itead Core module and a base board for the external
interfaces.

The core module comes with 4GB NAND and 1GB DDR RAM.

The base board to which the core board is connected provides 3 USB 2.0 Host
ports, 1 USB 2.0 OTG, 1 uSD slot, 10/100 Ethernet port, HDMI, IR receiver,
SPDIF and a 32-pin GPIO header. This header expands the features of core
board by exposing the VGA pins, audio In/Out pins, SATA, SPI, I2C, UARTS,
USB-OTG and power.

Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

It's device based on BCM47094 which is quite similar to BCM4709 except
for higher CPU frequency. This device has 2 flash memories, it boots
from serial one and stores firmware on NAND. Other than that we define
standard stuff like LEDs, buttons and UART.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Cubietruck Plus is a A83T/H8 based development board. The board has
standard DDR3 SDRAM, AXP818 PMIC/codec, SD/MMC, eMMC, USB 2.0 host
via HSIC USB Hub, USB OTG, SATA via USB bridge, gigabit ethernet,
WiFi, headphone out / mic in, and various GPIO headers.

The board also has an EEPROM on i2c0 which holds the MAC address.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

H8Homlet Proto v2.0 Board is A83T Dev Board by Allwinner.
It has UART, ethernet, USB, HDMI, etc ports on it.

A83T patches are tested on this board.
It has UART, ethernet, USB, HDMI, etc ports on it.

For FEL mode it needs USB A-A(Male) cable. I used uart0 which
is multiplexed to microsd pins PF2 and PF4.

Enabled UART0 Header(PB9, PB10 pins).

Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The Pi 2 B ends up like a Pi 1 B+, with the same peripherals and
pinout, but the CPU and memory layout changed to use the 2836.

Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

This allows us to boot dra62x j5-eco evm with NFSroot.

Signed-off-by: Tony Lindgren <tony@atomide.com>

This device tree was tested on a Sigma Designs SMP8758 Vantage-1172
Rev E1 development board.

Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

SBC-iMX7 is a single board computer designed for industrial
and embedded applications. It is based on the Freescale i.MX7
system-on-chip. SBC-iMX7 is implemented with the CL-SOM-iMX7
System-on-Module providing most of the functions, and SB-SOM-iMX7
carrier board providing additional peripheral functions and
connectors.

http://www.compulab.co.il/products/sbcs/sbc-imx7-freescale-i-mx-7-single-board-computer/

http://www.compulab.co.il/products/computer-on-modules/cl-som-imx7-freescale-i-mx-7-system-on-module/



Add basic board support, including SD card as a secondary boot and storage device

Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>

CL-SOM-iMX7 is a miniature System-on-Module (SoM) based on
Freescale i.MX7 System-on-Chip family.

http://www.compulab.co.il/products/computer-on-modules/cl-som-imx7-freescale-i-mx-7-system-on-module/



Add basic DT support for standalone module (without a carrier board):

* Memory configuration
* eMMC
* 2x Gigabit Ethernet ports (FEC1 and FEC2)
* I2C2 bus
  * EEPROM
  * PCA9555 GPIO extender
  * PMIC
* UART1
* USB OTG port

Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>

Novena is an open-hardware laptop/desktop/bare board.

See http://www.kosagi.com/w/index.php?title=Novena_Main_Page



Signed-off-by: Sean Cross <xobs@kosagi.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This device tree adds support for TS-4800 by Technologic Systems. This
board is based on MX51-babbage, but there are some subtle differences in
the pins used, and there is an additional FPGA that is memory-mapped.

More details here:
  http://wiki.embeddedarm.com/wiki/TS-4800



Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Minimal Cortex-M4 device tree to boot Linux to shell. M4 is booted via
Cortex-A5 running Linux using Stefan Agner's <stefan@agner.ch> "m4boot"
utility.

Signed-off-by: Afzal Mohammed <afzal.mohd.ma@gmail.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>