If NIC had packets in tx queue at the moment link down event
happened, it could result in tx timeout when link got back up.

Since device has more than one tx queue we need to reset them
accordingly.

Fixes: 057f4af2

 ("atl1c: add 4 RX/TX queue support for Mikrotik 10/25G NIC")
Signed-off-by: Gatis Peisenieks <gatis@mikrotik.com>
Link: https://lore.kernel.org/r/20220211065123.4187615-1-gatis@mikrotik.com


Signed-off-by: Jakub Kicinski <kuba@kernel.org>

We cannot do the cancel_work_sync from after the unregister_netdev, as
the dev pointer is no longer valid, causing a uaf on ldisc unregister
(or device close).

Instead, do the cancel_work_sync from the ndo_uninit op, where the dev
still exists, but the queue has stopped.

Fixes: 7bd9890f

 ("mctp: serial: cancel tx work on ldisc close")
Reported-by: Luo Likang <luolikang@nsfocus.com>
Tested-by: Luo Likang <luolikang@nsfocus.com>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Link: https://lore.kernel.org/r/20220211011552.1861886-1-jk@codeconstruct.com.au


Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The reset input to the LAN9303 chip is active low, and devicetree
gpio handles reflect this.  Therefore, the gpio should be requested
with an initial state of high in order for the reset signal to be
asserted.  Other uses of the gpio already use the correct polarity.

Fixes: a1292595

 ("net: dsa: add new DSA switch driver for the SMSC-LAN9303")
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fianelil <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220209145454.19749-1-mans@mansr.com


Signed-off-by: Jakub Kicinski <kuba@kernel.org>

wireless fixes for v5.17

Second set of fixes for v5.17. This is the first pull request with
both driver and stack patches.

Most important here are a regression fix for brcmfmac USB devices and
an iwlwifi fix for use after free when the firmware was missing. We
have new maintainers for ath9k and wcn36xx as well as ath6kl is now
orphaned. Also smaller fixes to iwlwifi and stack.

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following patchset contains Netfilter fixes for net:

1) Add selftest for nft_synproxy, from Florian Westphal.

2) xt_socket destroy path incorrectly disables IPv4 defrag for
   IPv6 traffic (typo), from Eric Dumazet.

3) Fix exit value selftest nft_concat_range.sh, from Hangbin Liu.

4) nft_synproxy disables the IPv4 hooks if the IPv6 hooks fail
   to be registered.

5) disable rp_filter on router in selftest nft_fib.sh, also
   from Hangbin Liu.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

trace_napi_poll_hit() is reading stat->dev while another thread can write
on it from dropmon_net_event()

Use READ_ONCE()/WRITE_ONCE() here, RCU rules are properly enforced already,
we only have to take care of load/store tearing.

BUG: KCSAN: data-race in dropmon_net_event / trace_napi_poll_hit

write to 0xffff88816f3ab9c0 of 8 bytes by task 20260 on cpu 1:
 dropmon_net_event+0xb8/0x2b0 net/core/drop_monitor.c:1579
 notifier_call_chain kernel/notifier.c:84 [inline]
 raw_notifier_call_chain+0x53/0xb0 kernel/notifier.c:392
 call_netdevice_notifiers_info net/core/dev.c:1919 [inline]
 call_netdevice_notifiers_extack net/core/dev.c:1931 [inline]
 call_netdevice_notifiers net/core/dev.c:1945 [inline]
 unregister_netdevice_many+0x867/0xfb0 net/core/dev.c:10415
 ip_tunnel_delete_nets+0x24a/0x280 net/ipv4/ip_tunnel.c:1123
 vti_exit_batch_net+0x2a/0x30 net/ipv4/ip_vti.c:515
 ops_exit_list net/core/net_namespace.c:173 [inline]
 cleanup_net+0x4dc/0x8d0 net/core/net_namespace.c:597
 process_one_work+0x3f6/0x960 kernel/workqueue.c:2307
 worker_thread+0x616/0xa70 kernel/workqueue.c:2454
 kthread+0x1bf/0x1e0 kernel/kthread.c:377
 ret_from_fork+0x1f/0x30

read to 0xffff88816f3ab9c0 of 8 bytes by interrupt on cpu 0:
 trace_napi_poll_hit+0x89/0x1c0 net/core/drop_monitor.c:292
 trace_napi_poll include/trace/events/napi.h:14 [inline]
 __napi_poll+0x36b/0x3f0 net/core/dev.c:6366
 napi_poll net/core/dev.c:6432 [inline]
 net_rx_action+0x29e/0x650 net/core/dev.c:6519
 __do_softirq+0x158/0x2de kernel/softirq.c:558
 do_softirq+0xb1/0xf0 kernel/softirq.c:459
 __local_bh_enable_ip+0x68/0x70 kernel/softirq.c:383
 __raw_spin_unlock_bh include/linux/spinlock_api_smp.h:167 [inline]
 _raw_spin_unlock_bh+0x33/0x40 kernel/locking/spinlock.c:210
 spin_unlock_bh include/linux/spinlock.h:394 [inline]
 ptr_ring_consume_bh include/linux/ptr_ring.h:367 [inline]
 wg_packet_decrypt_worker+0x73c/0x780 drivers/net/wireguard/receive.c:506
 process_one_work+0x3f6/0x960 kernel/workqueue.c:2307
 worker_thread+0x616/0xa70 kernel/workqueue.c:2454
 kthread+0x1bf/0x1e0 kernel/kthread.c:377
 ret_from_fork+0x1f/0x30

value changed: 0xffff88815883e000 -> 0x0000000000000000

Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 26435 Comm: kworker/0:1 Not tainted 5.17.0-rc1-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: wg-crypt-wg2 wg_packet_decrypt_worker

Fixes: 4ea7e386

 ("dropmon: add ability to detect when hardware dropsrxpackets")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The callback functions of clcsock will be saved and replaced during
the fallback. But if the fallback happens more than once, then the
copies of these callback functions will be overwritten incorrectly,
resulting in a loop call issue:

clcsk->sk_error_report
 |- smc_fback_error_report() <------------------------------|
     |- smc_fback_forward_wakeup()                          | (loop)
         |- clcsock_callback()  (incorrectly overwritten)   |
             |- smc->clcsk_error_report() ------------------|

So this patch fixes the issue by saving these function pointers only
once in the fallback and avoiding overwriting.

Reported-by:  <syzbot+4de3c0e8a263e1e499bc@syzkaller.appspotmail.com>
Fixes: 341adeec ("net/smc: Forward wakeup to smc socket waitqueue after fallback")
Link: https://lore.kernel.org/r/0000000000006d045e05d78776f6@google.com


Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from Jakub Kicinski:
 "Including fixes from netfilter and can.

Current release - new code bugs:

   - sparx5: fix get_stat64 out-of-bound access and crash

   - smc: fix netdev ref tracker misuse

  Previous releases - regressions:

   - eth: ixgbevf: require large buffers for build_skb on 82599VF, avoid
     overflows

   - eth: ocelot: fix all IP traffic getting trapped to CPU with PTP
     over IP

   - bonding: fix rare link activation misses in 802.3ad mode

  Previous releases - always broken:

   - tcp: fix tcp sock mem accounting in zero-copy corner cases

   - remove the cached dst when uncloning an skb dst and its metadata,
     since we only have one ref it'd lead to an UaF

   - netfilter:
      - conntrack: don't refresh sctp entries in closed state
      - conntrack: re-init state for retransmitted syn-ack, avoid
        connection establishment getting stuck with strange stacks
      ...

Merge tag 'linux-kselftest-fixes-5.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest

Pull Kselftest fixes from Shuah Khan:
 "Build and run-time fixes to pidfd, clone3, and ir tests"

* tag 'linux-kselftest-fixes-5.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
  selftests/ir: fix build with ancient kernel headers
  selftests: fixup build warnings in pidfd / clone3 tests
  pidfd: fix test failure due to stack overflow on some arches

Merge tag 'linux-kselftest-kunit-fixes-5.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest

Pull KUnit fixes from Shuah Khan:
 "Fixes to the test and usage documentation"

* tag 'linux-kselftest-kunit-fixes-5.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
  Documentation: KUnit: Fix usage bug
  kunit: fix missing f in f-string in run_checks.py

Some distros may enable rp_filter by default. After ns1 change addr to
10.0.2.99 and set default router to 10.0.2.1, while the connected router
address is still 10.0.1.1. The router will not reply the arp request
from ns1. Fix it by setting the router's veth0 rp_filter to 0.

Before the fix:
  # ./nft_fib.sh
  PASS: fib expression did not cause unwanted packet drops
  Netns nsrouter-HQkDORO2 fib counter doesn't match expected packet count of 1 for 1.1.1.1
  table inet filter {
          chain prerouting {
                  type filter hook prerouting priority filter; policy accept;
                  ip daddr 1.1.1.1 fib saddr . iif oif missing counter packets 0 bytes 0 drop
                  ip6 daddr 1c3::c01d fib saddr . iif oif missing counter packets 0 bytes 0 drop
          }
  }

After the fix:
  # ./nft_fib.sh
  PASS: fib expression did not cause unwanted packet drops
  PASS: fib expression did drop packets for 1.1.1.1
  PASS: fib expression did drop packets for 1c3::c01d

Fixes: 82944421

 ("selftests: netfilter: add fib test case")
Signed-off-by: Yi Chen <yiche@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Since struct mv88e6xxx_mdio_bus *mdio_bus is the bus->priv of something
allocated with mdiobus_alloc_size(), this means that mdiobus_free(bus)
will free the memory backing the mdio_bus as well. Therefore, the
mdio_bus->list element is freed memory, but we continue to iterate
through the list of MDIO buses using that list element.

To fix this, use the proper list iterator that handles element deletion
by keeping a copy of the list element next pointer.

Fixes: f53a2ce8

 ("net: dsa: mv88e6xxx: don't use devres for mdiobus")
Reported-by: Rafael Richter <rafael.richter@gin.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220210174017.3271099-1-vladimir.oltean@nxp.com


Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Tony Nguyen says:

====================
Intel Wired LAN Driver Updates 2022-02-10

Dan Carpenter propagates an error in FEC configuration.

Jesse fixes TSO offloads of IPIP and SIT frames.

Dave adds a dedicated LAG unregister function to resolve a KASAN error
and moves auxiliary device re-creation after LAG removal to the service
task to avoid issues with RTNL lock.

* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
  ice: Avoid RTNL lock when re-creating auxiliary device
  ice: Fix KASAN error in LAG NETDEV_UNREGISTER handler
  ice: fix IPIP and SIT TSO offload
  ice: fix an error code in ice_cfg_phy_fec()
====================

Link: https://lore.kernel.org/r/20220210170515.2609656-1-anthony.l.nguyen@intel.com


Signed-off-by: Jakub Kicinski <kuba@kernel.org>

An ongoing workqueue populates the stats buffer. At the same time, a user
might query the statistics. While writing to the buffer is mutex-locked,
reading from the buffer wasn't. This could lead to buggy reads by ethtool.

This patch fixes the former blamed commit, but the bug was introduced in
the latter.

Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Fixes: 1e1caa97 ("ocelot: Clean up stats update deferred work")
Fixes: a556c76a

 ("net: mscc: Add initial Ocelot switch support")
Reported-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/all/20220210150451.416845-2-colin.foster@in-advantage.com/


Signed-off-by: Jakub Kicinski <kuba@kernel.org>

If a call to re-create the auxiliary device happens in a context that has
already taken the RTNL lock, then the call flow that recreates auxiliary
device can hang if there is another attempt to claim the RTNL lock by the
auxiliary driver.

To avoid this, any call to re-create auxiliary devices that comes from
an source that is holding the RTNL lock (e.g. netdev notifier when
interface exits a bond) should execute in a separate thread.  To
accomplish this, add a flag to the PF that will be evaluated in the
service task and dealt with there.

Fixes: f9f5301e

 ("ice: Register auxiliary device to provide RDMA")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Reviewed-by: Jonathan Toppins <jtoppins@redhat.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Currently, the same handler is called for both a NETDEV_BONDING_INFO
LAG unlink notification as for a NETDEV_UNREGISTER call.  This is
causing a problem though, since the netdev_notifier_info passed has
a different structure depending on which event is passed.  The problem
manifests as a call trace from a BUG: KASAN stack-out-of-bounds error.

Fix this by creating a handler specific to NETDEV_UNREGISTER that only
is passed valid elements in the netdev_notifier_info struct for the
NETDEV_UNREGISTER event.

Also included is the removal of an unbalanced dev_put on the peer_netdev
and related braces.

Fixes: 6a8b3572

 ("ice: Respond to a NETDEV_UNREGISTER event for LAG")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Acked-by: Jonathan Toppins <jtoppins@redhat.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

The driver was avoiding offload for IPIP (at least) frames due to
parsing the inner header offsets incorrectly when trying to check
lengths.

This length check works for VXLAN frames but fails on IPIP frames
because skb_transport_offset points to the inner header in IPIP
frames, which meant the subtraction of transport_header from
inner_network_header returns a negative value (-20).

With the code before this patch, everything continued to work, but GSO
was being used to segment, causing throughputs of 1.5Gb/s per thread.
After this patch, throughput is more like 10Gb/s per thread for IPIP
traffic.

Fixes: e94d4478

 ("ice: Implement filter sync, NDO operations and bump version")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Propagate the error code from ice_get_link_default_override() instead
of returning success.

Fixes: ea78ce4d

 ("ice: add link lenient and default override support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

Otherwise, this test does not find the sysctl entry in place:

 sysctl: cannot stat /proc/sys/net/netfilter/nf_conntrack_tcp_loose: No such file or directory
 iperf3: error - unable to send control message: Bad file descriptor
 FAIL: iperf3 returned an error

Fixes: 7152303c

 ("selftests: netfilter: add synproxy test")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Disable the IPv4 hooks if the IPv6 hooks fail to be registered.

Fixes: ad49d86e

 ("netfilter: nf_tables: Add synproxy support")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

When building with automatic stack variable initialization, GCC 12
complains about variables defined outside of switch case statements.
Move the variable outside the switch, which silences the warning:

./net/mpls/af_mpls.c:1624:21: error: statement will never be executed [-Werror=switch-unreachable]
  1624 |                 int err;
       |                     ^~~

Signed-off-by: Victor Erminpour <victor.erminpour@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The netdev should be unregistered before we are disconnecting from the
MAC/PHY so that the dev_close callback is called and the PHY and the
phylink workqueues are actually stopped before we are disconnecting and
destroying the phylink instance.

Fixes: 71947923

 ("dpaa2-eth: add MAC/PHY support through phylink")
Signed-off-by: Robert-Ionut Alexa <robert-ionut.alexa@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove the second 'to'.

Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Single page and coherent memory blocks can use different DMA masks
when the macb accesses physical memory directly. The kernel is clever
enough to allocate pages that fit into the requested address width.

When using the ARM SMMU, the DMA mask must be the same for single
pages and big coherent memory blocks. Otherwise the translation
tables turn into one big mess.

  [   74.959909] macb ff0e0000.ethernet eth0: DMA bus error: HRESP not OK
  [   74.959989] arm-smmu fd800000.smmu: Unhandled context fault: fsr=0x402, iova=0x3165687460, fsynr=0x20001, cbfrsynra=0x877, cb=1
  [   75.173939] macb ff0e0000.ethernet eth0: DMA bus error: HRESP not OK
  [   75.173955] arm-smmu fd800000.smmu: Unhandled context fault: fsr=0x402, iova=0x3165687460, fsynr=0x20001, cbfrsynra=0x877, cb=1

Since using the same DMA mask does not hurt direct 1:1 physical
memory mappings, this commit always aligns DMA and coherent masks.

Signed-off-by: Marc St-Amand <mstamand@ciena.com>
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull MIPS fix from Thomas Bogendoerfer:
 "Device tree fix for Ingenic CI20"

* tag 'mips-fixes-5.17_3' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
  MIPS: DTS: CI20: fix how ddc power is enabled

Pull audit fix from Paul Moore:
 "Another audit fix, this time a single rather small but important fix
  for an oops/page-fault caused by improperly accessing userspace
  memory"

* tag 'audit-pr-20220209' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit:
  audit: don't deref the syscall args when checking the openat2 open_how::flags

The function tipc_mon_rcv() allows a node to receive and process
domain_record structs from peer nodes to track their views of the
network topology.

This patch verifies that the number of members in a received domain
record does not exceed the limit defined by MAX_MON_DOMAIN, something
that may otherwise lead to a stack overflow.

tipc_mon_rcv() is called from the function tipc_link_proto_rcv(), where
we are reading a 32 bit message data length field into a uint16.  To
avert any risk of bit overflow, we add an extra sanity check for this in
that function.  We cannot see that happen with the current code, but
future designers being unaware of this risk, may introduce it by
allowing delivery of very large (> 64k) sk buffers from the bearer
layer.  This potential problem was identified by Eric Dumazet.

This fixes CVE-2022-0435

Reported-by: Samuel Page <samuel.page@appgate.com>
Reported-by: Eric Dumazet <edumazet@google.com>
Fixes: 35c55c98

 ("tipc: add neighbor monitoring framework")
Signed-off-by: Jon Maloy <jmaloy@redhat.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Samuel Page <samuel.page@appgate.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If no firmware was present at all (or, presumably, all of the
firmware files failed to parse), we end up unbinding by calling
device_release_driver(), which calls remove(), which then in
iwlwifi calls iwl_drv_stop(), freeing the 'drv' struct. However
the new code I added will still erroneously access it after it
was freed.

Set 'failure=false' in this case to avoid the access, all data
was already freed anyway.

Cc: stable@vger.kernel.org
Reported-by: Stefan Agner <stefan@agner.ch>
Reported-by: Wolfgang Walter <linux@stwm.de>
Reported-by: Jason Self <jason@bluehome.net>
Reported-by: Dominik Behr <dominik@dominikbehr.com>
Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Fixes: ab07506b

 ("iwlwifi: fix leaks/bad data after failed firmware load")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220208114728.e6b514cf4c85.Iffb575ca2a623d7859b542c33b2a507d01554251@changeid

Mat Martineau says:

====================
mptcp: Fixes for 5.17

Patch 1 fixes a MPTCP selftest bug that combined the results of two
separate tests in the test output.

Patch 2 fixes a problem where advertised IPv6 addresses were not actually
available for incoming MP_JOIN requests.
====================

Link: https://lore.kernel.org/r/20220210012508.226880-1-mathew.j.martineau@linux.intel.com


Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This change updates mptcp_pm_nl_create_listen_socket() to create
listening sockets bound to IPv6 addresses (where IPv6 is supported).

Fixes: 1729cf18

 ("mptcp: create the listening socket for new port")
Acked-by: Geliang Tang <geliang.tang@suse.com>
Signed-off-by: Kishen Maloor <kishen.maloor@intel.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This function also writes the name of the test with its ID, making clear
a new test has been executed.

Without that, the ADD_ADDR results from this test was appended at the
end of the previous test causing confusions. Especially when the second
test was failing, we had:

  17 signal invalid addresses     syn[ ok ] - synack[ ok ] - ack[ ok ]
                                  add[ ok ] - echo  [ ok ]
                                  add[fail] got 2 ADD_ADDR[s] expected 3

In fact, this 17th test was OK but not the 18th one.

Now we have:

  17 signal invalid addresses     syn[ ok ] - synack[ ok ] - ack[ ok ]
                                  add[ ok ] - echo  [ ok ]
  18 signal addresses race test   syn[fail] got 2 JOIN[s] syn expected 3
   - synack[fail] got 2 JOIN[s] synack expected
   - ack[fail] got 2 JOIN[s] ack expected 3
                                  add[fail] got 2 ADD_ADDR[s] expected 3

Fixes: 33c563ad

 ("selftests: mptcp: add_addr and echo race test")
Reported-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Dell DW5829e same as DW5821e except the CAT level.
DW5821e supports CAT16 but DW5829e supports CAT9.
Also, DW5829e includes normal and eSIM type.
Please see below test evidence:

T:  Bus=04 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#=  5 Spd=5000 MxCh= 0
D:  Ver= 3.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS= 9 #Cfgs=  1
P:  Vendor=413c ProdID=81e6 Rev=03.18
S:  Manufacturer=Dell Inc.
S:  Product=DW5829e Snapdragon X20 LTE
S:  SerialNumber=0123456789ABCDEF
C:  #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=896mA
I:  If#=0x0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I:  If#=0x1 Alt= 0 #EPs= 1 Cls=03(HID  ) Sub=00 Prot=00 Driver=usbhid
I:  If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option

T:  Bus=04 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#=  7 Spd=5000 MxCh= 0
D:  Ver= 3.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS= 9 #Cfgs=  1
P:  Vendor=413c ProdID=81e4 Rev=03.18
S:  Manufacturer=Dell Inc.
S:  Product=DW5829e-eSIM Snapdragon X20 LTE
S:  SerialNumber=0123456789ABCDEF
C:  #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=896mA
I:  If#=0x0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I:  If#=0x1 Alt= 0 #EPs= 1 Cls=03(HID  ) Sub=00 Prot=00 Driver=usbhid
I:  If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option

Signed-off-by: Slark Xiao <slark_xiao@163.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Link: https://lore.kernel.org/r/20220209024717.8564-1-slark_xiao@163.com


Signed-off-by: Jakub Kicinski <kuba@kernel.org>

As reported by Jeff, dereferencing the openat2 syscall argument in
audit_match_perm() to obtain the open_how::flags can result in an
oops/page-fault.  This patch fixes this by using the open_how struct
that we store in the audit_context with audit_openat2_how().

Independent of this patch, Richard Guy Briggs posted a similar patch
to the audit mailing list roughly 40 minutes after this patch was
posted.

Cc: stable@vger.kernel.org
Fixes: 1c30e3af

 ("audit: add support for the openat2 syscall")
Reported-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>

Pull more nfsd fixes from Chuck Lever:
 "Ensure that NFS clients cannot send file size or offset values that
  can cause the NFS server to crash or to return incorrect or surprising
  results.

  In particular, fix how the NFS server handles values larger than
  OFFSET_MAX"

* tag 'nfsd-5.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux:
  NFSD: Deprecate NFS_OFFSET_MAX
  NFSD: Fix offset type in I/O trace points
  NFSD: COMMIT operations must not return NFS?ERR_INVAL
  NFSD: Clamp WRITE offsets
  NFSD: Fix NFSv3 SETATTR/CREATE's handling of large file sizes
  NFSD: Fix ia_size underflow
  NFSD: Fix the behavior of READ near OFFSET_MAX

Pull crypto fixes from Herbert Xu:
 "Fix two regressions:

   - Potential boot failure due to missing cryptomgr on initramfs

   - Stack overflow in octeontx2"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: api - Move cryptomgr soft dependency into algapi
  crypto: octeontx2 - Avoid stack variable overflow

Commit 3ba442d5 ("fs: move binfmt_misc sysctl to its own file") did
not go unnoticed, binfmt-support stopped to work on my Debian system
since v5.17-rc2 (did not check with -rc1).

The existance of the /proc/sys/fs/binfmt_misc is a precondition for
attempting to mount the binfmt_misc fs, which in turn triggers the
autoload of the binfmt_misc module.  Without it, no module is loaded and
no binfmt is available at boot.

Building as built-in or manually loading the module and mounting the fs
works fine, it's therefore only a matter of interaction with user-space.
I could try to improve the Debian systemd configuration but I can't say
anything about the other distributions.

This patch restores a working system right after boot.

Fixes: 3ba442d5

 ("fs: move binfmt_misc sysctl to its own file")
Signed-off-by: Domenico Andreoli <domenico.andreoli@linux.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Reviewed-by: Tong Zhang <ztong0001@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull s390 kvm fix from Christian Borntraeger:
 "Add missing check for the MEMOP ioctl

  The SIDA MEMOPs must only be used for secure guests, otherwise
  userspace can do unwanted memory accesses"

* tag 'kvm-s390-kernel-access' from emailed bundle:
  KVM: s390: Return error on SIDA memop on normal guest

NFS_OFFSET_MAX was introduced way back in Linux v2.3.y before there
was a kernel-wide OFFSET_MAX value. As a clean up, replace the last
few uses of it with its generic equivalent, and get rid of it.

Signed-off-by: Chuck Lever <chuck.lever@oracle.com>

NFSv3 and NFSv4 use u64 offset values on the wire. Record these values
verbatim without the implicit type case to loff_t.

Signed-off-by: Chuck Lever <chuck.lever@oracle.com>

Since, well, forever, the Linux NFS server's nfsd_commit() function
has returned nfserr_inval when the passed-in byte range arguments
were non-sensical.

However, according to RFC 1813 section 3.3.21, NFSv3 COMMIT requests
are permitted to return only the following non-zero status codes:

      NFS3ERR_IO
      NFS3ERR_STALE
      NFS3ERR_BADHANDLE
      NFS3ERR_SERVERFAULT

NFS3ERR_INVAL is not included in that list. Likewise, NFS4ERR_INVAL
is not listed in the COMMIT row of Table 6 in RFC 8881.

RFC 7530 does permit COMMIT to return NFS4ERR_INVAL, but does not
specify when it can or should be used.

Instead of dropping or failing a COMMIT request in a byte range that
is not supported, turn it into a valid request by treating one or
both arguments as zero. Offset zero means start-of-file, count zero
means until-end-of-file, so we only ever extend the commit range.
NFS servers are always allowed to commit more and sooner than
requested.

The range check is no longer bounded by NFS_OFFSET_MAX, but rather
by the value that is returned in the maxfilesize field of the NFSv3
FSINFO procedure or the NFSv4 maxfilesize file attribute.

Note that this change results in a new pynfs failure:

CMT4     st_commit.testCommitOverflow                             : RUNNING
CMT4     st_commit.testCommitOverflow                             : FAILURE
           COMMIT with offset + count overflow should return
           NFS4ERR_INVAL, instead got NFS4_OK

IMO the test is not correct as written: RFC 8881 does not allow the
COMMIT operation to return NFS4ERR_INVAL.

Reported-by: Dan Aloni <dan.aloni@vastdata.com>
Cc: stable@vger.kernel.org
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Bruce Fields <bfields@fieldses.org>