This is a generic dts file for A33 based q8 formfactor tablets,
this is intended to replace both sun8i-a33-ippo-q8h-v1.2.dts and
sun8i-a33-et-q8-v1.6.dts (these can be fully dropped after a
transition period).

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The bs1078v2 is a pcb found in 10.1" tablets with an A31 soc, 1G RAM
and 8G NAND, rtl8723as usb wifi, 1 micro USB OTG port, 1 USB HOST port

This commit adds a dts for v2 of the bs1078 pcb.

Signed-off-by: Lawrence Yu <lyu@micile.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

This commits adds a generic dts file for q8 formfactor a13 based tablets.

The tablets ship in many variants, with the difference mainly being the
touchscreen controller / accelerometer / wifi chip used.

The wifi is USB based, and thus not listed in devicetree.

The touchscreen controller / accelerometer may turn out to be a problem
once we add support for those. We can either do something with devicetree
overlays, or add sun5i-a13-<touchscreen>-<accelerometer>.dts files. The
latter is what the android mod community is doing with firmware images.

This dts was tested with an a13 q8 tablet with a pcb labelled: "94V-0",
silead gsl1680 touchscreen controller and a mc32x0 accelerometer.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The Wobo i5 top set box is a somewhat curious A10s based top set box,
it uses an AXP209 rather then the AXP152 usually used in combination
with the A10s. It has an ethernet phy connected to PORTD rather then
PORTA, and its built-in usb wifi is connected via the otg controller.

This commit adds a dts file adding support for this top set box.

Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The iNet-tek iNet-1 PCB is a PCB found in various generic 10.1" 1024x600
A10 based tablets such as the Point of View Protab2 XXL and the
Cherry M1007.

This patch has been tested on both rev2 and rev5 of this board / these
tablets.

It comes with a rtl8188cus usb wifi connected to ehci1, focal ft5406ee8
touchscreen connected to i2c2 addr 0x38, bosch bma 250 accelerometer
connected to i2c1 addr 0x18 and the usual connectors: headphone,
mini hdmi, power-barrel, mini-usb and a micro-sd slot.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The inet9f-rev03 pcb is specially designed for gaming tablets, such as
the qware tb-g100 tablet.

These 7" tablets feature a dpad, firebuttons and 2 joysticks on the sides
of the screen.

Besides this they have the usual connectors: power-barrel, mini usb,
mini hdmi, headphone and micro-sd slot.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The inet98v_rev2 is a pcb used in generic A13 based tablets. It features
volume buttons, a power barrel, micro-usb otg, headphone connector and
a power button.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The Auxtek-T003 HDMI stick is an A10s based HDMI stick with USB wifi,
and composite video out support.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The gt90h is a pcb found in generic 9" tablets with an A23 soc, 1G RAM
and 8G nand, rtl8723as usb wifi, 1 micro usb port and 1 micro sd slot.

This commit adds a dts for v4 of the gt90h pcb.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Commit 79ae3e66

 (ARM: dts: sun4i: Add Iteaduino Plus A10) added a new
make target for the sun4i-a10-itead-iteaduino-plus dts file, but mistakenly
used .dts instead of the correct .dtb suffix.  This resulted in a build error
like:

        scripts/Makefile.dtbinst:42: target 'sun4i-a10-itead-iteaduino-plus.dts' doesn't match the target pattern

when doing a make dtbs_install.

Fix it to use the proper file name.

Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

This change is a code reorganization. Here we introduce
serial_imx_enable_wakeup() helper function to do
the job of configuring and preparing wakeup sources
on imx serial device. The idea is to allow other
parts of the code to call this function whenever
the device is known to go to idle.

Cc: Fabio Estevam <festevam@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add new SOC i.MX6UL dtb file support, including evk board
support

i.MX6 Ultralite processor include one ARM cortext-A7 core.
Offer high perfomance and lowest power consumption.

Main included:
- 4 MMC/SD/SDIO
- 2 USB 2.0 OTG
- 3 I2S/SAI/AC97
- 4 eCSPI
- 4 I2C
- 2 ENET
- 2 CAN
- 3 wdog
- ASRC
- 8 uart
- LCDIF
- PXP

Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Fancy Fang <chen.fang@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Initial version of DTSI for ProXstream2 and PH1-LD6b and DTS for
PH1-LD6b reference board.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[olof: sort Makefile entries]
Signed-off-by: Olof Johansson <olof@lixom.net>

Turns out I fumbled a couple of the merge resolutions for marzen board removal.

Signed-off-by: Olof Johansson <olof@lixom.net>

Also known as the Asus Chromebook Flip.

Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>

The title says it all. The name of the dts file as been changed to
better reflect the manufacturer's device name (LS-WSGL), rather than
the original "lsmini", which exists in a kirkwood version too.

[gregory.clement@free-electrons.com]: use tab instead of space to
indent dts at line 185. Reslove merge conflict with patch "ARM: dts:
orion5x: add buffalo linkstation ls-wtgl" in the file
arch/arm/boot/dts/Makefile.

Signed-off-by: Benjamin Cama <benoar@dolka.fr>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Alexey Kopytko <alexey@kopytko.ru>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

Devkit8000 was sold with a 4.3" LCD or 7.0" or without. This patch
creates one dts file per bundle.

Signed-off-by: Anthoine Bourgeois <anthoine.bourgeois@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add minimal support for the new sama5d2 Xplained board. Only USB,
spi/i2c, ethernet and uart/usart peripherals added.
With this DTS file you can boot the board and begin to play with it.
Rootfs on NFS and sd card have successfully been tested.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

Add the initial device  tree for the R8A7794 SoC based SILK low cost board.
SCIF2 serial port support is included, so that the serial console can work.

Based on the original patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Remove Marzen legacy board code written in C. Instead
board support expressed in DT shall be used together
with Multiplatform and shmobile_defconfig.

Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add dts file to support Buffalo Linkstation LS-WTGL,
which is marvell orion5x based 2-bay 3.5" HDD NAS.
Product info:
 - (JPN) http://buffalo.jp/products/catalog/storage/ls-wtgl_r1/
 - (ENG) http://www.buffalotech.com/support-and-downloads/download/LinkStation_Pro_Duo_Manual_web.pdf



Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

Add minimal support for HP T410.

Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add minimal dts support for dm8148-evm.

Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Which is formally known as the Asus C201 chromebook

Signed-off-by: Romain Perier <romain.perier@gmail.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Main features of STM32429i-EVAL evaluation kit are:
 - STM32F429 Cortex-M4 MCU @180MHz
   * 2MB internal Flash
   * 256KB internal RAM
 - 32MB SDRAM
 - 16MB NOR Flash
 - 2MB SRAM
 - 4.3" TFT LCD with resistive touchscreen
 - SDCard connector (SDIO compatible)
 - 1x USB 2.0 OTG + 1x USB 1.1 OTG
 - Ethernet

Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>

The Terasic DE0 Atlas board is also known as the DE0-Nano board.
This patch adds the DTS board file for the DE0-Nano Sockit board, and not
the DE0 Nano "Development Board".

Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
---
v3: Updated skew settings for the gmac1 node as this board is using the
    KSZ9031 PHY instead of the 9021 PHY.
v2: use stdpath-out for console and remove comment regarding u-boot ethaddr

Iteaduino Plus A10 is a breakout board + Itead Core A10. It features 1GB RAM,
has most of the A10 pins on a .1" header, 2 USB ports, 1 OTG USB port,
Ethernet, HDMI, SATA, Speaker/Microphone 3.5mm jacks and an SD card slot.

Signed-off-by: Josef Gajdusek <atx@atx.name>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

phyBOARD-WEGA-AM335x represents a direct soldered
combination of a phyCORE-AM335x SoM and carrier board.

Different kind of SoM options can be connected to
the wega carrier board. So we created a separate
wega dtsi file. The final dts contains the actual
SoM on the carrier board.

WEGA carrier board features:
* ETH phy on carrier board: 1x MII
* 1x CAN
* 2x UART
* USB0 (device)
* USB1 (host)
* mSD slot

Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This adds basic chip support for Mediatek 6580.

Signed-off-by: Mars Cheng <mars.cheng@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>

While pinky was one of the earlier development models, is on the list
of endangered species today and nearly extinct, I want to keep mine
around for the foreseeable future after spending all the time making a
nice hole into the base below the dut-connector.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>

The Hisense Chromebook C11, also named jerry.

Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>

This board is used in some TV-boxes like for example the Beelink R89 or
Tronsmart R28.

The board itself follows the reference design for the most part. But
there are no schematics available it seems, so some things should be
taken with a grain of salt.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Romain Perier <romain.perier@gmail.com>

Add basic support for CIAA (Argentine Open Industrial Computer)
LPC4337 board. This commit enables the following peripherals:
  * UART
  * SSP
  * Ethernet

Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>

Also, reduce the maximum SPI device speed to the max. supported by the
LCD controller used on the LGPhilips LB035Q02 panel for this board.

Signed-off-by: Ash Charles <ashcharles@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The Gumstix "Tobi-Duo" expansion board [1] can be used with either
OMAP3 Overo or Overo Storm COMs.  It provides two NICs using LAN9221
chips.
It is necessary to duplicate the interface information for the
second SMSC9221 chip as discussed [2].

[1] https://store.gumstix.com/index.php/products/241/
[2] http://www.spinics.net/lists/linux-omap/msg115282.html



Signed-off-by: Ash Charles <ashcharles@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add dts file to support Buffalo Linkstation LS-WVL and LS-VL,
which are 3.5" HDD NAS in 2-bay and 1-bay respectively.

[gregory.clement@free-electrons.com: fix typo in pmx-led-function-red]
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Reviewed-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

Add dts file to support Buffalo Linkstation LS-WXL and LS-WSXL,
which are 2-bay NAS with 3.5" and 2.5" HDD respectively.

Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Reviewed-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

The Ippo-q8h is a tablet circuit board commonly found in cheap Android
tablets. The v1.2 version can be used with either an A23 or A33 SoC.

This version features 512 MB DRAM, 4G NAND, MMC, LCD, capacitive
touchscreen, accelerometer, 2 camera sensors, USB OTG, microphone
and speakers.

i2c0 is connected to the gsl1680 capacitive touch panel controller,
i2c1 is connected to an mma7660 3-axis accelerometer, these peripherals are
not supported by the kernel yet, i2c bus functionality has been tested via
i2c-dev.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[maxime: Removed the resolution mention, and modified the compatible to
         have a unique one with the A23 version]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Minimal DT description and Makefile entry for the Gose eval board.
Support for console, timer, and Ethernet.

Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The legacy board code for Armadillo-800 EVA has been removed.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>