Whilst MPIDR values themselves are less than 32 bits, it is still
perfectly valid for a DT to have #address-cells > 1 in the CPUs node,
resulting in the "reg" property having leading zero cell(s). In that
situation, the big-endian nature of the data conspires with the current
behaviour of only reading the first cell to cause the kernel to think
all CPUs have ID 0, and become resoundingly unhappy as a consequence.

Take the full property length into account when parsing CPUs so as to
be correct under any circumstances.

Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Add the required PCMCIA clock for the SA1111 "1800" device.  This clock
is used to compute timing information for the PCMCIA interface in the
SoC device, rather than the SA1111.  Hence, the provision of this clock
is a convenience for the driver and does not reflect the hardware, so
this must not be copied into DT.

Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

Accidentally booting Collie on Assabet reveals that the locomo driver
incorrectly overwrites gpio-sa1100's chip data for its parent interrupt,
leading to oops in sa1100_gpio_unmask() and sa1100_update_edge_regs()
when "gpio: sa1100: convert to use IO accessors" is applied.  Fix locomo
to use the handler data rather than chip data for its parent interrupt.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

The cachepolicy variable gets initialized using a masked pmd
value. So far, the pmd has been masked with flags valid for the
2-page table format, but the 3-page table format requires a
different mask. On LPAE, this lead to a wrong assumption of what
initial cache policy has been used. Later a check forces the
cache policy to writealloc and prints the following warning:
Forcing write-allocate cache policy for SMP

This patch introduces a new definition PMD_SECT_CACHE_MASK for
both page table formats which masks in all cache flags in both
cases.

Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

SA1111 forgets to call clk_disable() in the probe error cleanup path.
Add the necessary call.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

SA1111 PCMCIA was broken when PCMCIA switched to using dev_pm_ops for
the PCMCIA socket class.  PCMCIA used to handle suspend/resume via the
socket hosting device, which happened at normal device suspend/resume
time.

However, the referenced commit changed this: much of the resume now
happens much earlier, in the noirq resume handler of dev_pm_ops.

However, on SA1111, the PCMCIA device is not accessible as the SA1111
has not been resumed at _noirq time.  It's slightly worse than that,
because the SA1111 has already been put to sleep at _noirq time, so
suspend doesn't work properly.

Fix this by converting the core SA1111 code to use dev_pm_ops as well,
and performing its own suspend/resume at noirq time.

This fixes these errors in the kernel log:

pcmcia_socket pcmcia_socket0: time out after reset
pcmcia_socket pcmcia_socket1: time out after reset

and the resulting lack of PCMCIA cards after a S2RAM cycle.

Fixes: d7646f76

 ("pcmcia: use dev_pm_ops for class pcmcia_socket_class")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

The polarity of the high IRQs was being calculated using
SA1111_IRQMASK_HI(), but this assumes a Linux interrupt number, not a
hardware interrupt number.  Hence, the resulting mask was incorrect.
Fix this.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

Ensure that we propagate the platform_get_irq() error code out of the
probe function.  This allows probe deferrals to work correctly should
platform_get_irq() not be able to resolve the interrupt in a DT
environment at probe time.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

On lubbock board, the probe of the driver crashes by dereferencing very
early a platform_data structure which is not set, in
pxa2xx_configure_sockets().

The stack fixed is :
[    0.244353] SA1111 Microprocessor Companion Chip: silicon revision 1, metal revision 1
[    0.256321] sa1111 sa1111: Providing IRQ336-390
[    0.340899] clocksource: Switched to clocksource oscr0
[    0.472263] Unable to handle kernel NULL pointer dereference at virtual address 00000004
[    0.480469] pgd = c0004000
[    0.483432] [00000004] *pgd=00000000
[    0.487105] Internal error: Oops: f5 [#1] ARM
[    0.491497] Modules linked in:
[    0.494650] CPU: 0 PID: 1 Comm: swapper Not tainted 4.8.0-rc3-00080-g1aaa68426f0c-dirty #2068
[    0.503229] Hardware name: Intel DBPXA250 Development Platform (aka Lubbock)
[    0.510344] task: c3e42000 task.stack: c3e44000
[    0.514984] PC is at pxa2xx_configure_sockets+0x4/0x24 (drivers/pcmcia/pxa2xx_base.c:227)
[    0.520193] LR is at pcmcia_lubbock_init+0x1c/0x38
[    0.525079] pc : [<c0247c30>]    lr : [<c02479b0>]    psr: a0000053
[    0.525079] sp : c3e45e70  ip : 100019ff  fp : 00000000
[    0.536651] r10: c0828900  r9 : c0434838  r8 : 00000000
[    0.541953] r7 : c0820700  r6 : c0857b30  r5 : c3ec1400  r4 : c0820758
[    0.548549] r3 : 00000000  r2 : 0000000c  r1 : c3c09c40  r0 : c3ec1400
[    0.555154] Flags: NzCv  IRQs on  FIQs off  Mode SVC_32  ISA ARM  Segment none
[    0.562450] Control: 0000397f  Table: a0004000  DAC: 00000053
[    0.568257] Process swapper (pid: 1, stack limit = 0xc3e44190)
[    0.574154] Stack: (0xc3e45e70 to 0xc3e46000)
[    0.578610] 5e60:                                     c4849800 00000000 c3ec1400 c024769c
[    0.586928] 5e80: 00000000 c3ec140c c3c0ee0c c3ec1400 c3ec1434 c020c410 c3ec1400 c3ec1434
[    0.595244] 5ea0: c0820700 c080b408 c0828900 c020c5f8 00000000 c0820700 c020c578 c020ac5c
[    0.603560] 5ec0: c3e687cc c3e71e10 c0820700 00000000 c3c02de0 c020bae4 c03c62f7 c03c62f7
[    0.611872] 5ee0: c3e68780 c0820700 c042e034 00000000 c043c440 c020cdec c080b408 00000005
[    0.620188] 5f00: c042e034 c00096c0 c0034440 c01c730c 20000053 ffffffff 00000000 00000000
[    0.628502] 5f20: 00000000 c3ffcb87 c3ffcb90 c00346ac c3e66ba0 c03f7914 00000092 00000005
[    0.636811] 5f40: 00000005 c03f847c 00000091 c03f847c 00000000 00000005 c0434828 00000005
[    0.645125] 5f60: c043482c 00000092 c043c440 c0828900 c0434838 c0418d2c 00000005 00000005
[    0.653430] 5f80: 00000000 c041858c 00000000 c032e9f0 00000000 00000000 00000000 00000000
[    0.661729] 5fa0: 00000000 c032e9f8 00000000 c000f0f0 00000000 00000000 00000000 00000000
[    0.670020] 5fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    0.678311] 5fe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000
[    0.686673] (pxa2xx_configure_sockets) from pcmcia_lubbock_init (/drivers/pcmcia/sa1111_lubbock.c:161)
[    0.696026] (pcmcia_lubbock_init) from pcmcia_probe (/drivers/pcmcia/sa1111_generic.c:213)
[    0.704358] (pcmcia_probe) from driver_probe_device (/drivers/base/dd.c:378 /drivers/base/dd.c:499)
[    0.712848] (driver_probe_device) from __driver_attach (/./include/linux/device.h:983 /drivers/base/dd.c:733)
[    0.721414] (__driver_attach) from bus_for_each_dev (/drivers/base/bus.c:313)
[    0.729723] (bus_for_each_dev) from bus_add_driver (/drivers/base/bus.c:708)
[    0.738036] (bus_add_driver) from driver_register (/drivers/base/driver.c:169)
[    0.746185] (driver_register) from do_one_initcall (/init/main.c:778)
[    0.754561] (do_one_initcall) from kernel_init_freeable (/init/main.c:843 /init/main.c:851 /init/main.c:869 /init/main.c:1016)
[    0.763409] (kernel_init_freeable) from kernel_init (/init/main.c:944)
[    0.771660] (kernel_init) from ret_from_fork (/arch/arm/kernel/entry-common.S:119)
[ 0.779347] Code: c03c6305 c03c631e c03c632e e5903048 (e993000c)
All code
========
   0:	c03c6305 	eorsgt	r6, ip, r5, lsl #6
   4:	c03c631e 	eorsgt	r6, ip, lr, lsl r3
   8:	c03c632e 	eorsgt	r6, ip, lr, lsr #6
   c:	e5903048 	ldr	r3, [r0, #72]	; 0x48
  10:*	e993000c 	ldmib	r3, {r2, r3}		<-- trapping instruction

Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

When testing Lubbock, it was noticed that the sa1111 pcmcia driver bound
but was not functional due to no sockets being registered.  This is
because the return code from the lowlevel board initialisation was not
being propagated out of the probe function.  Fix this.

Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

SS_STSCHG should be set for an IO card when the BVD1 signal is asserted
low, not high.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

Add units to the timing information, so we know that the numbers are
nanoseconds.  The output changes from:

I/O      : 165 (172)
attribute: 300 (316)
common   : 300 (316)

to:

I/O      : 165ns (172ns)
attribute: 300ns (316ns)
common   : 300ns (316ns)

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

Fix the reporting of the currently programmed timing information.  These
entries have been showing zero due to the clock rate being a factor of
1000 too big.  With this change, we go from:

I/O      : 165 (0)
attribute: 300 (0)
common   : 300 (0)

to:

I/O      : 165 (172)
attribute: 300 (316)
common   : 300 (316)

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

PCMCIA suspend/resume no longer works since the commit mentioned below,
as the callbacks are no longer made.  Convert the driver to the new
dev_pm_ops, which restores the suspend/resume functionality.  Tested on
the arm arch Assabet platform.

Fixes: aa8e54b5

 ("PM / sleep: Go direct_complete if driver has no callbacks")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>

Commit aa719874

 ("nvme: fabrics drivers don't need the nvme-pci
driver") removed the dependency on BLK_DEV_NVME, but the cdoe does
depend on the block layer (which used to be an implicit dependency
through BLK_DEV_NVME).

Otherwise you get various errors from the kbuild test robot random
config testing when that happens to hit a configuration with BLOCK
device support disabled.

Cc: Christoph Hellwig <hch@lst.de>
Cc: Jay Freyensee <james_p_freyensee@linux.intel.com>
Cc: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull IIO fixes from Greg KH:
 "Here are a few small IIO fixes for 4.8-rc6.

  Nothing major, full details are in the shortlog, all of these have
  been in linux-next with no reported issues"

* tag 'staging-4.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  iio:core: fix IIO_VAL_FRACTIONAL sign handling
  iio: ensure ret is initialized to zero before entering do loop
  iio: accel: kxsd9: Fix scaling bug
  iio: accel: bmc150: reset chip at init time
  iio: fix pressure data output unit in hid-sensor-attributes
  tools:iio:iio_generic_buffer: fix trigger-less mode

Pull USB fixes from Greg KH:
 "Here are some small USB gadget, phy, and xhci fixes for 4.8-rc6.

  All of these resolve minor issues that have been reported, and all
  have been in linux-next with no reported issues"

* tag 'usb-4.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: chipidea: udc: fix NULL ptr dereference in isr_setup_status_phase
  xhci: fix null pointer dereference in stop command timeout function
  usb: dwc3: pci: fix build warning on !PM_SLEEP
  usb: gadget: prevent potenial null pointer dereference on skb->len
  usb: renesas_usbhs: fix clearing the {BRDY,BEMP}STS condition
  usb: phy: phy-generic: Check clk_prepare_enable() error
  usb: gadget: udc: renesas-usb3: clear VBOUT bit in DRD_CON
  Revert "usb: dwc3: gadget: always decrement by 1"

Pull libnvdimm fixes from Dan Williams:
 "nvdimm fixes for v4.8, two of them are tagged for -stable:

   - Fix devm_memremap_pages() to use track_pfn_insert().  Otherwise,
     DAX pmd mappings end up with an uncached pgprot, and unusable
     performance for the device-dax interface.  The device-dax interface
     appeared in 4.7 so this is tagged for -stable.

   - Fix a couple VM_BUG_ON() checks in the show_smaps() path to
     understand DAX pmd entries.  This fix is tagged for -stable.

   - Fix a mis-merge of the nfit machine-check handler to flip the
     polarity of an if() to match the final version of the patch that
     Vishal sent for 4.8-rc1.  Without this the nfit machine check
     handler never detects / inserts new 'badblocks' entries which
     applications use to identify lost portions of files.

   - For test purposes, fix the nvdimm_clear_poison() path to operate on
     legacy / simulated nvdimm memory ranges.  Without this fix a test
     can set badblocks, but never clear them on these ranges.

   - Fix the range checking done by dax_dev_pmd_fault().  This is not
     tagged for -stable since this problem is mitigated by specifying
     aligned resources at device-dax setup time.

  These patches have appeared in a next release over the past week.  The
  recent rebase you can see in the timestamps was to drop an invalid fix
  as identified by the updated device-dax unit tests [1].  The -mm
  touches have an ack from Andrew"

[1]: "[ndctl PATCH 0/3] device-dax test for recent kernel bugs"
   https://lists.01.org/pipermail/linux-nvdimm/2016-September/006855.html

* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  libnvdimm: allow legacy (e820) pmem region to clear bad blocks
  nfit, mce: Fix SPA matching logic in MCE handler
  mm: fix cache mode of dax pmd mappings
  mm: fix show_smap() for zone_device-pmd ranges
  dax: fix mapping size check

Pull i2c fixes from Wolfram Sang:
 "Mostly driver bugfixes, but also a few cleanups which are nice to have
  out of the way"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: rk3x: Restore clock settings at resume time
  i2c: Spelling s/acknowedge/acknowledge/
  i2c: designware: save the preset value of DW_IC_SDA_HOLD
  Documentation: i2c: slave-interface: add note for driver development
  i2c: mux: demux-pinctrl: run properly with multiple instances
  i2c: bcm-kona: fix inconsistent indenting
  i2c: rcar: use proper device with dma_mapping_error
  i2c: sh_mobile: use proper device with dma_mapping_error
  i2c: mux: demux-pinctrl: invalidate properly when switching fails

Pull fscrypto fixes fromTed Ts'o:
 "Fix some brown-paper-bag bugs for fscrypto, including one one which
  allows a malicious user to set an encryption policy on an empty
  directory which they do not own"

* tag 'for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  fscrypto: require write access to mount to set encryption policy
  fscrypto: only allow setting encryption policy on directories
  fscrypto: add authorization check for setting encryption policy

Since setting an encryption policy requires writing metadata to the
filesystem, it should be guarded by mnt_want_write/mnt_drop_write.
Otherwise, a user could cause a write to a frozen or readonly
filesystem.  This was handled correctly by f2fs but not by ext4.  Make
fscrypt_process_policy() handle it rather than relying on the filesystem
to get it right.

Signed-off-by: Eric Biggers <ebiggers@google.com>
Cc: stable@vger.kernel.org # 4.1+; check fs/{ext4,f2fs}
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Acked-by: Jaegeuk Kim <jaegeuk@kernel.org>

The FS_IOC_SET_ENCRYPTION_POLICY ioctl allowed setting an encryption
policy on nondirectory files.  This was unintentional, and in the case
of nonempty regular files did not behave as expected because existing
data was not actually encrypted by the ioctl.

In the case of ext4, the user could also trigger filesystem errors in
->empty_dir(), e.g. due to mismatched "directory" checksums when the
kernel incorrectly tried to interpret a regular file as a directory.

This bug affected ext4 with kernels v4.8-rc1 or later and f2fs with
kernels v4.6 and later.  It appears that older kernels only permitted
directories and that the check was accidentally lost during the
refactoring to share the file encryption code between ext4 and f2fs.

This patch restores the !S_ISDIR() check that was present in older
kernels.

Signed-off-by: Eric Biggers <ebiggers@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Theodore Ts'o <tytso@mit.edu>

On an ext4 or f2fs filesystem with file encryption supported, a user
could set an encryption policy on any empty directory(*) to which they
had readonly access.  This is obviously problematic, since such a
directory might be owned by another user and the new encryption policy
would prevent that other user from creating files in their own directory
(for example).

Fix this by requiring inode_owner_or_capable() permission to set an
encryption policy.  This means that either the caller must own the file,
or the caller must have the capability CAP_FOWNER.

(*) Or also on any regular file, for f2fs v4.6 and later and ext4
    v4.8-rc1 and later; a separate bug fix is coming for that.

Signed-off-by: Eric Biggers <ebiggers@google.com>
Cc: stable@vger.kernel.org # 4.1+; check fs/{ext4,f2fs}
Signed-off-by: Theodore Ts'o <tytso@mit.edu>

Bad blocks can be injected via /sys/block/pmemN/badblocks. In a situation
where legacy pmem is being used or a pmem region created by using memmap
kernel parameter, the injected bad blocks are not cleared due to
nvdimm_clear_poison() failing from lack of ndctl function pointer. In
this case we need to just return as handled and allow the bad blocks to
be cleared rather than fail.

Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

The check for a 'pmem' type SPA in the MCE handler was inverted due to a
merge/rebase error.

Fixes: 6839a6d9

 nfit: do an ARS scrub on hitting a latent media error
Cc: linux-acpi@vger.kernel.org
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

track_pfn_insert() in vmf_insert_pfn_pmd() is marking dax mappings as
uncacheable rendering them impractical for application usage.  DAX-pte
mappings are cached and the goal of establishing DAX-pmd mappings is to
attain more performance, not dramatically less (3 orders of magnitude).

track_pfn_insert() relies on a previous call to reserve_memtype() to
establish the expected page_cache_mode for the range.  While memremap()
arranges for reserve_memtype() to be called, devm_memremap_pages() does
not.  So, teach track_pfn_insert() and untrack_pfn() how to handle
tracking without a vma, and arrange for devm_memremap_pages() to
establish the write-back-cache reservation in the memtype tree.

Cc: <stable@vger.kernel.org>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Nilesh Choudhury <nilesh.choudhury@oracle.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-by: Toshi Kani <toshi.kani@hpe.com>
Reported-by: Kai Zhang <kai.ka.zhang@oracle.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

Attempting to dump /proc/<pid>/smaps for a process with pmd dax mappings
currently results in the following VM_BUG_ONs:

 kernel BUG at mm/huge_memory.c:1105!
 task: ffff88045f16b140 task.stack: ffff88045be14000
 RIP: 0010:[<ffffffff81268f9b>]  [<ffffffff81268f9b>] follow_trans_huge_pmd+0x2cb/0x340
 [..]
 Call Trace:
  [<ffffffff81306030>] smaps_pte_range+0xa0/0x4b0
  [<ffffffff814c2755>] ? vsnprintf+0x255/0x4c0
  [<ffffffff8123c46e>] __walk_page_range+0x1fe/0x4d0
  [<ffffffff8123c8a2>] walk_page_vma+0x62/0x80
  [<ffffffff81307656>] show_smap+0xa6/0x2b0

 kernel BUG at fs/proc/task_mmu.c:585!
 RIP: 0010:[<ffffffff81306469>]  [<ffffffff81306469>] smaps_pte_range+0x499/0x4b0
 Call Trace:
  [<ffffffff814c2795>] ? vsnprintf+0x255/0x4c0
  [<ffffffff8123c46e>] __walk_page_range+0x1fe/0x4d0
  [<ffffffff8123c8a2>] walk_page_vma+0x62/0x80
  [<ffffffff81307696>] show_smap+0xa6/0x2b0

These locations are sanity checking page flags that must be set for an
anonymous transparent huge page, but are not set for the zone_device
pages associated with dax mappings.

Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

Pull virtio fixes from Michael Tsirkin:
 "This includes a couple of bugfixs for virtio.

  The virtio console patch is actually also in x86/tip targeting 4.9
  because it helps vmap stacks, but it also fixes IOMMU_PLATFORM which
  was added in 4.8, and it seems important not to ship that in a broken
  configuration"

* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
  virtio_console: Stop doing DMA on the stack
  virtio: mark vring_dma_dev() static

Pull power management fixes from Rafael Wysocki:
 "This includes a PM QoS framework fix from Tejun to prevent interrupts
  from being enabled unexpectedly during early boot and a cpufreq
  documentation fix.

  Specifics:

   - If the PM QoS framework invokes cancel_delayed_work_sync() during
     early boot, it will enable interrupts which is not expected at that
     point, so prevent it from happening (Tejun Heo)

   - Fix cpufreq statistic documentation to follow a recent change in
     behavior that forgot to update it as appropriate (Jean Delvare)"

* tag 'pm-4.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  cpufreq-stats: Minor documentation fix
  PM / QoS: avoid calling cancel_delayed_work_sync() during early boot

* pm-core-fixes:
  PM / QoS: avoid calling cancel_delayed_work_sync() during early boot

* pm-cpufreq-fixes:
  cpufreq-stats: Minor documentation fix

Pull GPIO fixes from Linus Walleij:
 "Some GPIO fixes that have been boiling the last two weeks or so.
  Nothing special, I'm trying to sort out some Kconfig business and
  Russell needs a fix in for -his SA1100 rework.

  Summary:

   - Revert a pointless attempt to add an include to solve the UM allyes
     compilation problem.

   - Make the mcp23s08 depend on OF_GPIO as it uses it and doesn't
     compile properly without it.

   - Fix a probing problem for ucb1x00"

* tag 'gpio-v4.8-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio: sa1100: fix irq probing for ucb1x00
  gpio: mcp23s08: make driver depend on OF_GPIO
  Revert "gpio: include <linux/io-mapping.h> in gpiolib-of"

Pull fuse fix from Miklos Szeredi:
 "This fixes a deadlock when fuse, direct I/O and loop device are
  combined"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
  fuse: direct-io: don't dirty ITER_BVEC pages

Pull overlayfs fix from Miklos Szeredi:
 "This fixes a regression caused by the last pull request"

* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
  ovl: fix workdir creation

Pull btrfs fixes from Chris Mason:
 "I'm not proud of how long it took me to track down that one liner in
  btrfs_sync_log(), but the good news is the patches I was trying to
  blame for these problems were actually fine (sorry Filipe)"

* 'for-linus-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  btrfs: introduce tickets_id to determine whether asynchronous metadata reclaim work makes progress
  btrfs: remove root_log_ctx from ctx list before btrfs_sync_log returns
  btrfs: do not decrease bytes_may_use when replaying extents

Pull sound fixes from Takashi Iwai:
 "We've got quite a few fixes at this time, and all are stable patches.

  syzkaller strikes back again (episode 19 or so), and we had to plug
  some holes in ALSA core part (mostly timer).

  In addition, a couple of FireWire audio fixes for the invalid copy
  user calls in locks, and a few quirks for HD-audio and USB-audio as
  usual are included"

* tag 'sound-4.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: rawmidi: Fix possible deadlock with virmidi registration
  ALSA: timer: Fix zero-division by continue of uninitialized instance
  ALSA: timer: fix NULL pointer dereference in read()/ioctl() race
  ALSA: fireworks: accessing to user space outside spinlock
  ALSA: firewire-tascam: accessing to user space outside spinlock
  ALSA: hda - Enable subwoofer on Dell Inspiron 7559
  ALSA: hda - Add headset mic quirk for Dell Inspiron 5468
  ALSA: usb-audio: Add sample rate inquiry quirk for B850V3 CP2114
  ALSA: timer: fix NULL pointer dereference on memory allocation failure
  ALSA: timer: fix division by zero after SNDRV_TIMER_IOCTL_CONTINUE

virtio_console uses a small DMA buffer for control requests.  Move
that buffer into heap memory.

Doing virtio DMA on the stack is normally okay on non-DMA-API virtio
systems (which is currently most of them), but it breaks completely
if the stack is virtually mapped.

Tested by typing both directions using picocom aimed at /dev/hvc0.

Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>

We get 1 warning when building kernel with W=1:
drivers/virtio/virtio_ring.c:170:16: warning: no previous prototype for 'vring_dma_dev' [-Wmissing-prototypes]

In fact, this function is only used in the file in which it is
declared and don't need a declaration, but can be made static.
so this patch marks this function with 'static'.

Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>

Pull arm64 fixes from Catalin Marinas:

 - smp_mb__before_spinlock() changed to smp_mb() on arm64 since the
   generic definition to smp_wmb() is not sufficient

 - avoid a recursive loop with the graph tracer by using using
   preempt_(enable|disable)_notrace in _percpu_(read|write)

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: use preempt_disable_notrace in _percpu_read/write
  arm64: spinlocks: implement smp_mb__before_spinlock() as smp_mb()