Store the caller for each multicall so we can report it on failure.

Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

When testing for a dom0/initial/privileged domain, make sure the
predicate evaluates to a compile-time 0 if CONFIG_XEN_DOM0 isn't
enabled.  This will make most of the dom0 code evaporate without
much more effort.

Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Merge branches 'x86/paravirt', 'x86/pat', 'x86/setup-v2', 'x86/subarch', 'x86/uaccess' and 'x86/urgent' into x86/core

Merge branches 'x86/acpi', 'x86/asm', 'x86/cpudetect', 'x86/crashdump', 'x86/debug', 'x86/defconfig', 'x86/doc', 'x86/header-fixes', 'x86/headers' and 'x86/minor-fixes' into x86/core

Conflicts:
	arch/x86/kernel/acpi/boot.c
	arch/x86/mm/fault.c

Between 2.6.23 and 2.6.24-rc1 a change was made that broke IBM LS21
systems that had the HPET enabled in the BIOS, resulting in boot hangs
for x86_64.

Specifically commit b8ce3359

, which
merges the i386 and x86_64 HPET code.

Prior to this commit, when we setup the HPET timers in x86_64, we did
the following:

	hpet_writel(HPET_TN_ENABLE | HPET_TN_PERIODIC | HPET_TN_SETVAL |
                    HPET_TN_32BIT, HPET_T0_CFG);

However after the i386/x86_64 HPET merge, we do the following:

	cfg = hpet_readl(HPET_Tn_CFG(timer));
	cfg |= HPET_TN_ENABLE | HPET_TN_PERIODIC |
			HPET_TN_SETVAL | HPET_TN_32BIT;
	hpet_writel(cfg, HPET_Tn_CFG(timer));

However on LS21s with HPET enabled in the BIOS, the HPET_T0_CFG register
boots with Level triggered interrupts (HPET_TN_LEVEL) enabled. This
causes the periodic interrupt to be not so periodic, and that results in
the boot time hang I reported earlier in the delay calibration.

My fix: Always disable HPET_TN_LEVEL when setting up periodic mode.

Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Impact: Flush the lazy MMU only once

Pending mmu updates only need to be flushed once to bring the
in-memory pagetable state up to date.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

Impact: Catch cases where lazy MMU state is active in a preemtible context

arch_flush_lazy_mmu_cpu() has been changed to disable preemption so
the checks in enter/leave will never trigger. Put the preemtible()
check into arch_flush_lazy_mmu_cpu() to catch such cases.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

Impact: avoid access to percpu vars in preempible context

They are intended to be used whenever there's the possibility
that there's some stale state which is going to be overwritten
with a queued update, or to force a state change when we may be
in lazy mode.  Either way, we could end up calling it with
preemption enabled, so wrap the functions in their own little
preempt-disable section so they can be safely called in any
context (though preemption should never be enabled if we're actually
in a lazy state).

(Move out of line to avoid #include dependencies.)
    
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6:
  mm: Export symbol ksize()

A bug was introduced into write_cache_pages cyclic writeout by commit
31a12666 ("mm: write_cache_pages cyclic
fix").  The intention (and comments) is that we should cycle back and
look for more dirty pages at the beginning of the file if there is no
more work to be done.

But the !done condition was dropped from the test.  This means that any
time the page writeout loop breaks (eg.  due to nr_to_write == 0), we
will set index to 0, then goto again.  This will set done_index to
index, then find done is set, so will proceed to the end of the
function.  When updating mapping->writeback_index for cyclic writeout,
we now use done_index == 0, so we're always cycling back to 0.

This seemed to be causing random mmap writes (slapadd and iozone) to
start writing more pages from the LRU and writeout would slowdown, and
caused bugzilla entry

	http://bugzilla.kernel.org/show_bug.cgi?id=12604



about Berkeley DB slowing down dramatically.

With this patch, iozone random write performance is increased nearly
5x on my system (iozone -B -r 4k -s 64k -s 512m -s 1200m on ext2).

Signed-off-by: Nick Piggin <npiggin@suse.de>
Reported-and-tested-by: Jan Kara <jack@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit 7b2cd92a

 ("crypto: api - Fix
zeroing on free") added modular user of ksize(). Export that to fix
crypto.ko compilation.

Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Kirill A. Shutemov <kirill@shutemov.name>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>

Impact: cleanup

Make the max_low_pfn logic a bit more standard between
lowmem_pfn_init() and highmem_pfn_init().

Signed-off-by: Ingo Molnar <mingo@elte.hu>

Impact: cleanup

Split find_low_pfn_range() into two functions:

 - lowmem_pfn_init()
 - highmem_pfn_init()

The former gets called if all of RAM fits into lowmem,
otherwise we call highmem_pfn_init().

Signed-off-by: Ingo Molnar <mingo@elte.hu>

Signed-off-by: Ingo Molnar <mingo@elte.hu>

It was enabled by mistake - iscsi is not included in a typical
default PC, and no other architecture has it built-in (=y) either.

Turn it off.

Signed-off-by: Ingo Molnar <mingo@elte.hu>

deprecation warnings have become rather noisy lately:

drivers/i2c/i2c-core.c: In function ‘i2c_new_device’:
drivers/i2c/i2c-core.c:283: warning: ‘i2c_attach_client’ is deprecated (declared at include/linux/i2c.h:434)
drivers/i2c/i2c-core.c: In function ‘i2c_del_adapter’:
drivers/i2c/i2c-core.c:646: warning: ‘detach_client’ is deprecated (declared at include/linux/i2c.h:154)
drivers/i2c/i2c-core.c: In function ‘i2c_register_driver’:
drivers/i2c/i2c-core.c:713: warning: ‘detach_client’ is deprecated (declared at include/linux/i2c.h:154)
drivers/i2c/i2c-core.c: In function ‘__detach_adapter’:
drivers/i2c/i2c-core.c:780: warning: ‘detach_client’ is deprecated (declared at include/linux/i2c.h:154)
drivers/i2c/i2c-core.c: At top level:
drivers/i2c/i2c-core.c:876: warning: ‘i2c_attach_client’ is deprecated (declared at drivers/i2c/i2c-core.c:827)
drivers/i2c/i2c-core.c:876: warning: ‘i2c_attach_client’ is deprecated (declared at drivers/i2c/i2c-core.c:827)
drivers/i2c/i2c-core.c:904: warning: ‘i2c_detach_client’ is deprecated (declared at drivers/i2c/i2c-core.c:879)
drivers/i2c/i2c-core.c:904: warning: ‘i2c_detach_client’ is deprecated (declared at drivers/i2c/i2c-core.c:879)

So turn it off for now - these reminders can obscure critical warnings.

Signed-off-by: Ingo Molnar <mingo@elte.hu>

Signed-off-by: Ingo Molnar <mingo@elte.hu>

Signed-off-by: Ingo Molnar <mingo@elte.hu>

Jeff Mahoney reported:

> With Suse's hwinfo tool, on -tip:
> WARNING: at arch/x86/mm/pat.c:637 reserve_pfn_range+0x5b/0x26d()

reserve_pfn_range() is not tracking the memory range below 1MB
as non-RAM and as such is inconsistent with similar checks in
reserve_memtype() and free_memtype()

Rename the pagerange_is_ram() to pat_pagerange_is_ram() and add the
"track legacy 1MB region as non RAM" condition.

And also, fix reserve_pfn_range() to return -EINVAL, when the pfn
range is RAM. This is to be consistent with this API design.

Reported-and-tested-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Impact: fix race leading to crash under KVM and Xen

The CPA code may be called while we're in lazy mmu update mode - for
example, when using DEBUG_PAGE_ALLOC and doing a slab allocation
in an interrupt handler which interrupted a lazy mmu update.  In this
case, the in-memory pagetable state may be out of date due to pending
queued updates.  We need to flush any pending updates before inspecting
the page table.  Similarly, we must explicitly flush any modifications
CPA may have made (which comes down to flushing queued operations when
flushing the TLB).

Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Acked-by: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Stable Kernel <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>

Impact: Fixes warning

Fix uv.h struct usage:

arch/x86/include/asm/uv/uv.h:16: warning: 'struct mm_struct' declared inside parameter list
arch/x86/include/asm/uv/uv.h:16: warning: its scope is only this definition or declaration, which is probably not what you want

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>

Impact: cleanup

With the recent changes in the 32-bit code to make system calls which
use struct pt_regs take a pointer, sys_rt_sigreturn() have become
identical between 32 and 64 bits, and both are empty wrappers around
do_rt_sigreturn().  Remove both wrappers and rename both to
sys_rt_sigreturn().

Cc: Brian Gerst <brgerst@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>

* git://git.infradead.org/users/cbou/battery-2.6.29:
  pcf50633_charger: Fix typo

Addresses http://bugzilla.kernel.org/show_bug.cgi?id=12646



When the temperature exceeds 32767 milli-degrees the temperature overflows
to -32768 millidegrees.  These are bothe well within the -55 - +125 degree
range for the sensor.

Fix overflow in left-shift of a u8.

Signed-off-by: Ian Dall <ian@beware.dropbear.id.au>
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix a problem that causes I/O to a disconnected (or partially initialized)
nbd device to hang indefinitely.  To reproduce:

# ioctl NBD_SET_SIZE_BLOCKS /dev/nbd23 514048
# dd if=/dev/nbd23 of=/dev/null bs=4096 count=1

...hangs...

This can also occur when an nbd device loses its nbd-client/server
connection.  Although we clear the queue of any outstanding I/Os after the
client/server connection fails, any additional I/Os that get queued later
will hang.

This bug may also be the problem reported in this bug report:
http://bugzilla.kernel.org/show_bug.cgi?id=12277



Testing would need to be performed to determine if the two issues are the
same.

This problem was introduced by the new request handling thread code ("NBD:
allow nbd to be used locally", 3/2008), which entered into mainline around
2.6.25.

The fix, which is fairly simple, is to restore the check for lo->sock
being NULL in do_nbd_request.  This causes I/O to an uninitialized nbd to
immediately fail with an I/O error, as it did prior to the introduction of
this bug.

Signed-off-by: Paul Clements <paul.clements@steeleye.com>
Reported-by: Jon Nelson <jnelson-kernel-bugzilla@jamponi.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: <stable@kernel.org>		[2.6.26.x, 2.6.27.x, 2.6.28.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Christophe Saout reported [in precursor to:
http://marc.info/?l=linux-kernel&m=123209902707347&w=4

]:

> Note that I also some a different issue with CONFIG_UNEVICTABLE_LRU.
> Seems like Xen tears down current->mm early on process termination, so
> that __get_user_pages in exit_mmap causes nasty messages when the
> process had any mlocked pages.  (in fact, it somehow manages to get into
> the swapping code and produces a null pointer dereference trying to get
> a swap token)

Jeremy explained:

Yes.  In the normal case under Xen, an in-use pagetable is "pinned",
meaning that it is RO to the kernel, and all updates must go via hypercall
(or writes are trapped and emulated, which is much the same thing).  An
unpinned pagetable is not currently in use by any process, and can be
directly accessed as normal RW pages.

As an optimisation at process exit time, we unpin the pagetable as early
as possible (switching the process to init_mm), so that all the normal
pagetable teardown can happen with direct memory accesses.

This happens in exit_mmap() -> arch_exit_mmap().  The munlocking happens
a few lines below.  The obvious thing to do would be to move
arch_exit_mmap() to below the munlock code, but I think we'd want to
call it even if mm->mmap is NULL, just to be on the safe side.

Thus, this patch:

exit_mmap() needs to unlock any locked vmas before calling arch_exit_mmap,
as the latter may switch the current mm to init_mm, which would cause the
former to fail.

Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Christophe Saout <christophe@saout.de>
Cc: Keir Fraser <keir.fraser@eu.citrix.com>
Cc: Christophe Saout <christophe@saout.de>
Cc: Alex Williamson <alex.williamson@hp.com>
Cc: <stable@kernel.org>		[2.6.28.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Since netmos 9835 with subids 0x1014(IBM):0x0299 is now bound with
serial/8250_pci, because it has no parallel ports and subdevice id isn't
in the expected form, return -ENODEV from probe function.

This is performed in netmos preinit_hook.

Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit dcf6a79d

 ("write-back: fix
nr_to_write counter") fixed nr_to_write counter, but didn't set the break
condition properly.

If nr_to_write == 0 after being decremented it will loop one more time
before setting done = 1 and breaking the loop.

[akpm@linux-foundation.org: coding-style fixes]
Cc: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Acked-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

With the new system call defines we get this on uml:

arch/um/sys-i386/built-in.o: In function `sys_call_table':
(.rodata+0x308): undefined reference to `sys_sigprocmask'

Reason for this is that uml passes the preprocessor option
-Dsigprocmask=kernel_sigprocmask to gcc when compiling the kernel.
This causes SYSCALL_DEFINE3(sigprocmask, ...) to be expanded to
SYSCALL_DEFINEx(3, kernel_sigprocmask, ...) and finally to a system
call named sys_kernel_sigprocmask.  However sys_sigprocmask is missing
because of this.

To avoid macro expansion for the system call name just concatenate the
name at first define instead of carrying it through severel levels.
This was pointed out by Al Viro.

Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Reviewed-by: WANG Cong <wangcong@zeuux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

For a reason that I was unable to understand in three months of debugging,
mount ext2 -o remount stopped working properly when remounting from
regular operation to xip, or the other way around.  According to a git
bisect search, the problem was introduced with the VM_MIXEDMAP/PTE_SPECIAL
rework in the vm:

commit 70688e4d


Author: Nick Piggin <npiggin@suse.de>
Date:   Mon Apr 28 02:13:02 2008 -0700

    xip: support non-struct page backed memory

In the failing scenario, the filesystem is mounted read only via root=
kernel parameter on s390x.  During remount (in rc.sysinit), the inodes of
the bash binary and its libraries are busy and cannot be invalidated (the
bash which is running rc.sysinit resides on subject filesystem).
Afterwards, another bash process (running ifup-eth) recurses into a
subshell, runs dup_mm (via fork).  Some of the mappings in this bash
process were created from inodes that could not be invalidated during
remount.

Both parent and child process crash some time later due to inconsistencies
in their address spaces.  The issue seems to be timing sensitive, various
attempts to recreate it have failed.

This patch refuses to change the xip flag during remount in case some
inodes cannot be invalidated.  This patch keeps users from running into
that issue.

[akpm@linux-foundation.org: cleanup]
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Jared Hulbert <jaredeh@gmail.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

I enabled all cgroup subsystems when compiling kernel, and then:
 # mount -t cgroup -o net_cls xxx /mnt
 # mkdir /mnt/0

This showed up immediately:
 BUG: MAX_LOCKDEP_SUBCLASSES too low!
 turning off the locking correctness validator.

It's caused by the cgroup hierarchy lock:
	for (i = 0; i < CGROUP_SUBSYS_COUNT; i++) {
		struct cgroup_subsys *ss = subsys[i];
		if (ss->root == root)
			mutex_lock_nested(&ss->hierarchy_mutex, i);
	}

Now we have 9 cgroup subsystems, and the above 'i' for net_cls is 8, but
MAX_LOCKDEP_SUBCLASSES is 8.

This patch uses different lockdep keys for different subsystems.

Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Paul Menage <menage@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add Li Zefan as co-maintainer.

Acked-by: Paul Menage <menage@google.com>
Acked-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

With a postfix decrement t will reach -1 rather than 0, so neither the
warning nor the `goto error_out' will occur.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix kernel-doc processing of SYSCALL wrappers.

The SYSCALL wrapper patches played havoc with kernel-doc for
syscalls.  Syscalls that were scanned for DocBook processing
reported warnings like this one, for sys_tgkill:

Warning(kernel/signal.c:2285): No description found for parameter 'tgkill'
Warning(kernel/signal.c:2285): No description found for parameter 'pid_t'
Warning(kernel/signal.c:2285): No description found for parameter 'int'

because the macro parameters all "look like" function parameters,
although they are not:

/**
 *  sys_tgkill - send signal to one specific thread
 *  @tgid: the thread group ID of the thread
 *  @pid: the PID of the thread
 *  @sig: signal to be sent
 *
 *  This syscall also checks the @tgid and returns -ESRCH even if the PID
 *  exists but it's not belonging to the target process anymore. This
 *  method solves the problem of threads exiting and PIDs getting reused.
 */
SYSCALL_DEFINE3(tgkill, pid_t, tgid, pid_t, pid, int, sig)
{
...

This patch special-cases the handling SYSCALL_DEFINE* function
prototypes by expanding them to
	long sys_foobar(type1 arg1, type1 arg2, ...)

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix kernel-doc-nano-HOWTO.txt to use */ as the ending marker in kernel-doc
examples and state that */ is the preferred ending marker.

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Reported-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

page_cgroup's page allocation at init/memory hotplug uses kmalloc() and
vmalloc(). If kmalloc() failes, vmalloc() is used.

This is because vmalloc() is very limited resource on 32bit systems.
We want to use kmalloc() first.

But in this kind of call, __GFP_NOWARN should be specified.

Reported-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>