We don't want to disconnect a session because of a stray PADT arriving
while the interface is in promiscuous mode.
Furthermore, multicast and broadcast packets make no sense here, so
only PACKET_HOST is accepted.

Reported-by: David Balažic <xerces9@gmail.com>
Fixes: 1da177e4

 ("Linux-2.6.12-rc2")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Driver missed initializing num_por which is one of the por values that
driver configures to hardware. In order to get these values, add a new
structure ethqos_emac_driver_data which holds por and num_por values
and populate that in driver probe.

Fixes: a7c30e62

 ("net: stmmac: Add driver for Qualcomm ethqos")
Reported-by: Rahul Ankushrao Kawadgave <rahulak@qti.qualcomm.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

phy_restart_aneg() enables aneg in the PHY. That's not what we want
if phydev->autoneg is disabled. In this case still update EEE
advertisement register, but don't enable aneg and don't trigger an
aneg restart.

Fixes: f75abeb8

 ("net: phy: restart phy autonegotiation after EEE advertisment change")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The GENET controller on the Raspberry Pi 4 (2711) is typically
interfaced with an external Broadcom PHY via a RGMII electrical
interface. To make sure that delays are properly configured at the PHY
side, ensure that we the dedicated Broadcom PHY driver
(CONFIG_BROADCOM_PHY) is enabled for this to happen.

Fixes: 402482a6

 ("net: bcmgenet: Clear ID_MODE_DIS in EXT_RGMII_OOB_CTRL when not needed")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tuong Lien says:

====================
tipc: add some patches

This series adds patches to fix some issues in TIPC streaming & service
subscription.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

When a service subscription is expired or canceled by user, it needs to
be deleted from the subscription list, so that new subscriptions can be
registered (max = 65535 per net). However, there are two issues in code
that can cause such an unused subscription to persist:

1) The 'tipc_conn_delete_sub()' has a loop on the subscription list but
it makes a break shortly when the 1st subscription differs from the one
specified, so the subscription will not be deleted.

2) In case a subscription is canceled, the code to remove the
'TIPC_SUB_CANCEL' flag from the subscription filter does not work if it
is a local subscription (i.e. the little endian isn't involved). So, it
will be no matches when looking for the subscription to delete later.

The subscription(s) will be removed eventually when the user terminates
its topology connection but that could be a long time later. Meanwhile,
the number of available subscriptions may be exhausted.

This commit fixes the two issues above, so as needed a subscription can
be deleted correctly.

Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Upon receipt of a service subscription request from user via a topology
connection, one 'sub' object will be allocated in kernel, so it will be
able to send an event of the service if any to the user correspondingly
then. Also, in case of any failure, the connection will be shutdown and
all the pertaining 'sub' objects will be freed.

However, there is a race condition as follows resulting in memory leak:

       receive-work       connection        send-work
              |                |                |
        sub-1 |<------//-------|                |
        sub-2 |<------//-------|                |
              |                |<---------------| evt for sub-x
        sub-3 |<------//-------|                |
              :                :                :
              :                :                :
              |       /--------|                |
              |       |        * peer closed    |
              |       |        |                |
              |       |        |<-------X-------| evt for sub-y
              |       |        |<===============|
        sub-n |<------/        X    shutdown    |
    -> orphan |                                 |

That is, the 'receive-work' may get the last subscription request while
the 'send-work' is shutting down the connection due to peer close.

We had a 'lock' on the connection, so the two actions cannot be carried
out simultaneously. If the last subscription is allocated e.g. 'sub-n',
before the 'send-work' closes the connection, there will be no issue at
all, the 'sub' objects will be freed. In contrast the last subscription
will become orphan since the connection was closed, and we released all
references.

This commit fixes the issue by simply adding one test if the connection
remains in 'connected' state right after we obtain the connection lock,
then a subscription object can be created as usual, otherwise we ignore
it.

Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Reported-by: Thang Ngo <thang.h.ngo@dektech.com.au>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently when a connection is in Nagle mode, we set the 'ack_required'
bit in the last sending buffer and wait for the corresponding ACK prior
to pushing more data. However, on the receiving side, the ACK is issued
only when application really  reads the whole data. Even if part of the
last buffer is received, we will not do the ACK as required. This might
cause an unnecessary delay since the receiver does not always fetch the
message as fast as the sender, resulting in a large latency in the user
message sending, which is: [one RTT + the receiver processing time].

The commit makes Nagle ACK as soon as possible i.e. when a message with
the 'ack_required' arrives in the receiving side's stack even before it
is processed or put in the socket receive queue...
This way, we can limit the streaming latency to one RTT as committed in
Nagle mode.

Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ursula Braun says:

====================
s390/net: updates 2020-05-13

please apply the fix from Wei Yongjun to netdev's net tree and
add Karsten Graul as co-maintainer for drivers/s390/net.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Add Karsten as additional maintainer for drivers/s390/net .
One of his focal points is the ism driver.

Cc: Julian Wiedmann <jwi@linux.ibm.com>
Acked-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix to return negative error code -ENOMEM from the smcd_alloc_dev()
error handling case instead of 0, as done elsewhere in this function.

Fixes: 684b89bc

 ("s390/ism: add device driver for internal shared memory")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The cipso and calipso code can set the MLS_CAT attribute on
successful parsing, even if the corresponding catmap has
not been allocated, as per current configuration and external
input.

Later, selinux code tries to access the catmap if the MLS_CAT flag
is present via netlbl_catmap_getlong(). That may cause null ptr
dereference while processing incoming network traffic.

Address the issue setting the MLS_CAT flag only if the catmap is
really allocated. Additionally let netlbl_catmap_getlong() cope
with NULL catmap.

Reported-by: Matthew Sheets <matthew.sheets@gd-ms.com>
Fixes: 4b8feff2 ("netlabel: fix the horribly broken catmap functions")
Fixes: ceba1832

 ("calipso: Set the calipso socket label to match the secattr.")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We autotune rcvbuf whenever SO_RCVLOWAT is set to account for 100%
overhead in tcp_set_rcvlowat()

This works well when skb->len/skb->truesize ratio is bigger than 0.5

But if we receive packets with small MSS, we can end up in a situation
where not enough bytes are available in the receive queue to satisfy
RCVLOWAT setting.
As our sk_rcvbuf limit is hit, we send zero windows in ACK packets,
preventing remote peer from sending more data.

Even autotuning does not help, because it only triggers at the time
user process drains the queue. If no EPOLLIN is generated, this
can not happen.

Note poll() has a similar issue, after commit
c7004482 ("tcp: Respect SO_RCVLOWAT in tcp_poll().")

Fixes: 03f45c88

 ("tcp: avoid extra wakeups for SO_RCVLOWAT users")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

My recent commit b6d49cab ("net: Make PTP-specific drivers depend on
PTP_1588_CLOCK") exposes a missing dependency in defconfigs that select
TI_CPTS without selecting PTP_1588_CLOCK, leading to linker errors of the
form:

drivers/net/ethernet/ti/cpsw.o: in function `cpsw_ndo_stop':
cpsw.c:(.text+0x680): undefined reference to `cpts_unregister'
 ...

That's because TI_CPTS_MOD (which is the symbol gating the _compilation_ of
cpts.c) now depends on PTP_1588_CLOCK, and so is not enabled in these
configurations, but TI_CPTS (which is the symbol gating _calls_ to the cpts
functions) _is_ enabled. So we end up compiling calls to functions that
don't exist, resulting in the linker errors.

This patch fixes build errors and restores previous behavior by:
 - ensure PTP_1588_CLOCK=y in TI specific configs and CPTS will be built
 - remove TI_CPTS_MOD and, instead, add dependencies from CPTS in
   TI_CPSW/TI_KEYSTONE_NETCP/TI_CPSW_SWITCHDEV as below:

   config TI_CPSW_SWITCHDEV
   ...
    depends on TI_CPTS || !TI_CPTS

   which will ensure proper dependencies PTP_1588_CLOCK -> TI_CPTS ->
TI_CPSW/TI_KEYSTONE_NETCP/TI_CPSW_SWITCHDEV and build type selection.

Note. For NFS boot + CPTS all of above configs have to be built-in.

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Fixes: b6d49cab

 ("net: Make PTP-specific drivers depend on PTP_1588_CLOCK")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Clay McClure <clay@daemons.net>
[grygorii.strashko@ti.com: rewording, add deps cpsw/netcp from cpts, drop IS_REACHABLE]
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Shannon Nelson says:

====================
ionic fixes

These are a couple more fixes after more fw-upgrade testing.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

Since the fw has been re-inited, we need to refresh the port
information dma address so we can see fresh port information.
Let's call ionic_port_init again, and tweak it to allow for
a call to simply refresh the existing dma address.

Fixes: c672412f

 ("ionic: remove lifs on fw reset")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

When running in a bond setup, or some other potential
configurations, the netdev mac may have been changed from
the default device mac.  Since the userland doesn't know
about the changes going on under the covers in a fw-upgrade
it doesn't know the re-push the mac filter.  The driver
needs to leave the netdev mac filter alone when rebuilding
after the fw-upgrade.

Fixes: c672412f

 ("ionic: remove lifs on fw reset")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

The do_aux_work callback had documentation in the structure comment
which referred to it as "do_work".

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the other MPTCP-peer uses 32-bit data-sequence numbers, we rely on
map_seq to indicate how to expand to a 64-bit data-sequence number in
expand_seq() when receiving data.

For new subflows, this field is not initialized, thus results in an
"invalid" mapping being discarded.

Fix this by initializing map_seq upon subflow establishment time.

Fixes: f296234c

 ("mptcp: Add handling of incoming MP_JOIN requests")
Signed-off-by: Christoph Paasch <cpaasch@apple.com>
Reviewed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alex Elder says:

====================
net: ipa: fix cleanup after modem crash

The first patch in this series fixes a bug where the size of a data
transfer request was never set, meaning it was 0.  The consequence
of this was that such a transfer request would never complete if
attempted, and led to a hung task timeout.

This data transfer is required for cleaning up IPA hardware state
when recovering from a modem crash.  The code to implement this
cleanup is already present, but its use was commented out because
it hit the bug described above.  So the second patch in this series
enables the use of that "tag process" cleanup code.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

One part of recovering from a modem crash is performing a "tag
sequence" of several IPA immediate commands, to clear the hardware
pipeline.  The sequence ends with a data transfer request on the
command endpoint (which is not otherwise done).  Unfortunately,
attempting to do the data transfer led to a hang, so that request
plus two other commands were commented out.

The previous commit fixes the bug that was causing that hang.  And
with that bug fixed we can properly issue the tag sequence when the
modem crashes, to return the hardware to a known state.

Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a command gets added to a transaction for the AP->command
channel we set the DMA address of its scatterlist entry, but not
its DMA length.  Fix this bug.

Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

if some function in ndo_stop interface returns failure because of
hardware fault, must go on excuting rest steps rather than return
failure directly, otherwise will cause memory leak.And bump the
timeout for SET_FUNC_STATE to ensure that cmd won't return failure
when hw is busy. Otherwise hw may stomp host memory if we free
memory regardless of the return value of SET_FUNC_STATE.

Fixes: 51ba902a

 ("net-next/hinic: Initialize hw interface")
Signed-off-by: Luo bin <luobin9@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

There is a soft dependency against dsa_loop_bdinfo.ko which sets up the
MDIO device registration, since there are no symbols referenced by
dsa_loop.ko, there is no automatic loading of dsa_loop_bdinfo.ko which
is needed.

Fixes: 98cd1552

 ("net: dsa: Mock-up driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

If systemd is configured to use hybrid mode which enables the use of
both cgroup v1 and v2, systemd will create new cgroup on both the default
root (v2) and netprio_cgroup hierarchy (v1) for a new session and attach
task to the two cgroups. If the task does some network thing then the v2
cgroup can never be freed after the session exited.

One of our machines ran into OOM due to this memory leak.

In the scenario described above when sk_alloc() is called
cgroup_sk_alloc() thought it's in v2 mode, so it stores
the cgroup pointer in sk->sk_cgrp_data and increments
the cgroup refcnt, but then sock_update_netprioidx()
thought it's in v1 mode, so it stores netprioidx value
in sk->sk_cgrp_data, so the cgroup refcnt will never be freed.

Currently we do the mode switch when someone writes to the ifpriomap
cgroup control file. The easiest fix is to also do the switch when
a task is attached to a new cgroup.

Fixes: bd1060a1

 ("sock, cgroup: add sock->sk_cgroup")
Reported-by: Yang Yingliang <yangyingliang@huawei.com>
Tested-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Zefan Li <lizefan@huawei.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

I ran into a randconfig build failure with CONFIG_FIXED_PHY=m
and CONFIG_GIANFAR=y:

x86_64-linux-ld: drivers/net/ethernet/freescale/gianfar.o:(.rodata+0x418): undefined reference to `fixed_phy_change_carrier'

It seems the same thing can happen with dpaa and ucc_geth, so change
all three to do an explicit 'select FIXED_PHY'.

The fixed-phy driver actually has an alternative stub function that
theoretically allows building network drivers when fixed-phy is
disabled, but I don't see how that would help here, as the drivers
presumably would not work then.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In commit b406472b ("net: ipv4: avoid mixed n_redirects and
rate_tokens usage") I missed the fact that a 0 'rate_tokens' will
bypass the backoff algorithm.

Since rate_tokens is cleared after a redirect silence, and never
incremented on redirects, if the host keeps receiving packets
requiring redirect it will reply ignoring the backoff.

Additionally, the 'rate_last' field will be updated with the
cadence of the ingress packet requiring redirect. If that rate is
high enough, that will prevent the host from generating any
other kind of ICMP messages

The check for a zero 'rate_tokens' value was likely a shortcut
to avoid the more complex backoff algorithm after a redirect
silence period. Address the issue checking for 'n_redirects'
instead, which is incremented on successful redirect, and
does not interfere with other ICMP replies.

Fixes: b406472b

 ("net: ipv4: avoid mixed n_redirects and rate_tokens usage")
Reported-and-tested-by: Colin Walters <walters@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Fix to return negative error code -ENOMEM from the alloc failed error
handling case instead of 0, as done elsewhere in this function.

Fixes: 3184fb5b

 ("octeontx2-vf: Virtual function driver support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

If a UMH process created by fork_usermode_blob() fails to execute,
a pair of struct file allocated by umh_pipe_setup() will leak.

Under normal conditions, the caller (like bpfilter) needs to manage the
lifetime of the UMH and its two pipes. But when fork_usermode_blob()
fails, the caller doesn't really have a way to know what needs to be
done. It seems better to do the cleanup ourselves in this case.

Fixes: 449325b5

 ("umh: introduce fork_usermode_blob() helper")
Signed-off-by: Vincent Minet <v.minet@criteo.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Daniel Borkmann says:

====================
pull-request: bpf 2020-05-09

The following pull-request contains BPF updates for your *net* tree.

We've added 4 non-merge commits during the last 9 day(s) which contain
a total of 4 files changed, 11 insertions(+), 6 deletions(-).

The main changes are:

1) Fix msg_pop_data() helper incorrectly setting an sge length in some
   cases as well as fixing bpf_tcp_ingress() wrongly accounting bytes
   in sg.size, from John Fastabend.

2) Fix to return an -EFAULT error when copy_to_user() of the value
   fails in map_lookup_and_delete_elem(), from Wei Yongjun.

3) Fix sk_psock refcnt leak in tcp_bpf_recvmsg(), from Xiyu Yang.
====================

Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The "location" is controlled by the user via the ethtool_set_rxnfc()
function.  This update_cls_rule() function checks for array overflows
but it doesn't check if the value is negative.  I have changed the type
to unsigned to prevent array underflows.

Fixes: afb90dbb

 ("dpaa2-eth: Add ethtool support for flow classification")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Fix to return negative error code -ENOMEM from the kzalloc() error
handling case instead of 0, as done elsewhere in this function.

Fixes: 174ab544

 ("nfp: abm: add cls_u32 offload for simple band classification")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

r8169 never had native support for the RTL8401, however it reportedly
worked with the fallback to RTL8101e [0]. Therefore let's add this
as an explicit assignment.

[0] https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=956868

Fixes: b4cc2dcc

 ("r8169: remove default chip versions")
Reported-by: Camaleón <noelamac@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The stated intent of the original commit is to is to "return the timestamp
corresponding to the highest sequence number data returned." The current
implementation returns the timestamp for the last byte of the last fully
read skb, which is not necessarily the last byte in the recv buffer. This
patch converts behavior to the original definition, and to the behavior of
the previous draft versions of commit 98aaa913 ("tcp: Extend
SOF_TIMESTAMPING_RX_SOFTWARE to TCP recvmsg") which also match this
behavior.

Fixes: 98aaa913

 ("tcp: Extend SOF_TIMESTAMPING_RX_SOFTWARE to TCP recvmsg")
Co-developed-by: Iris Liu <iris@onechronos.com>
Signed-off-by: Iris Liu <iris@onechronos.com>
Signed-off-by: Kelly Littlepage <kelly@onechronos.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

syzbot managed to trigger a recursive NETDEV_FEAT_CHANGE event
between bonding master and slave. I managed to find a reproducer
for this:

  ip li set bond0 up
  ifenslave bond0 eth0
  brctl addbr br0
  ethtool -K eth0 lro off
  brctl addif br0 bond0
  ip li set br0 up

When a NETDEV_FEAT_CHANGE event is triggered on a bonding slave,
it captures this and calls bond_compute_features() to fixup its
master's and other slaves' features. However, when syncing with
its lower devices by netdev_sync_lower_features() this event is
triggered again on slaves when the LRO feature fails to change,
so it goes back and forth recursively until the kernel stack is
exhausted.

Commit 17b85d29 intentionally lets __netdev_update_features()
return -1 for such a failure case, so we have to just rely on
the existing check inside netdev_sync_lower_features() and skip
NETDEV_FEAT_CHANGE event only for this specific failure case.

Fixes: fd867d51

 ("net/core: generic support for disabling netdev features down stack")
Reported-by:  <syzbot+e73ceacfd8560cc8a3ca@syzkaller.appspotmail.com>
Reported-by:  <syzbot+c2fb6f9ddcea95ba49b5@syzkaller.appspotmail.com>
Cc: Jarod Wilson <jarod@redhat.com>
Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Jann Horn <jannh@google.com>
Reviewed-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a subflow is created via mptcp_subflow_create_socket(),
a new 'struct socket' is allocated, with a new i_ino value.

When inspecting TCP sockets via the procfs and or the diag
interface, the above ones are not related to the process owning
the MPTCP master socket, even if they are a logical part of it
('ss -p' shows an empty process field)

Additionally, subflows created by the path manager get
the uid/gid from the running workqueue.

Subflows are part of the owning MPTCP master socket, let's
adjust the vfs info to reflect this.

After this patch, 'ss' correctly displays subflows as belonging
to the msk socket creator.

Fixes: 2303f994

 ("mptcp: Associate MPTCP context with TCP socket")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This driver calls kthread_run() in probe, but forgets to call
kthread_stop() in probe failure and remove.
Add the missed kthread_stop() to fix it.

Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 19bda36c

:

| ipv6: add mtu lock check in __ip6_rt_update_pmtu
|
| Prior to this patch, ipv6 didn't do mtu lock check in ip6_update_pmtu.
| It leaded to that mtu lock doesn't really work when receiving the pkt
| of ICMPV6_PKT_TOOBIG.
|
| This patch is to add mtu lock check in __ip6_rt_update_pmtu just as ipv4
| did in __ip_rt_update_pmtu.

The above reasoning is incorrect.  IPv6 *requires* icmp based pmtu to work.
There's already a comment to this effect elsewhere in the kernel:

  $ git grep -p -B1 -A3 'RTAX_MTU lock'
  net/ipv6/route.c=4813=

  static int rt6_mtu_change_route(struct fib6_info *f6i, void *p_arg)
  ...
    /* In IPv6 pmtu discovery is not optional,
       so that RTAX_MTU lock cannot disable it.
       We still use this lock to block changes
       caused by addrconf/ndisc.
    */

This reverts to the pre-4.9 behaviour.

Cc: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Xin Long <lucien.xin@gmail.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Fixes: 19bda36c

 ("ipv6: add mtu lock check in __ip6_rt_update_pmtu")
Signed-off-by: David S. Miller <davem@davemloft.net>

clang points out that building without IPv6 would lead to returning
an uninitialized variable if a packet with family!=AF_INET is
passed into bareudp_udp_encap_recv():

drivers/net/bareudp.c:139:6: error: variable 'err' is used uninitialized whenever 'if' condition is false [-Werror,-Wsometimes-uninitialized]
        if (family == AF_INET)
            ^~~~~~~~~~~~~~~~~
drivers/net/bareudp.c:146:15: note: uninitialized use occurs here
        if (unlikely(err)) {
                     ^~~
include/linux/compiler.h:78:42: note: expanded from macro 'unlikely'
 # define unlikely(x)    __builtin_expect(!!(x), 0)
                                            ^
drivers/net/bareudp.c:139:2: note: remove the 'if' if its condition is always true
        if (family == AF_INET)
        ^~~~~~~~~~~~~~~~~~~~~~

This cannot happen in practice, so change the condition in a way that
gcc sees the IPv4 case as unconditionally true here.
For consistency, change all the similar constructs in this file the
same way, using "if(IS_ENABLED())" instead of #if IS_ENABLED()".

Fixes: 571912c6

 ("net: UDP tunnel encapsulation module for tunnelling different protocols like MPLS, IP, NSH etc.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The HNS config symbol enables the framework support for the Hisilicon
Network Subsystem.  It is already selected by all of its users, so there
is no reason to make it visible.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>