The A31 Hummingbird has a mini USB OTG port, and uses GPIO pins from the
SoC for ID pin and VBUS detection and VBUS control. The PMIC can also do
VBUS detection and control.

Here we prefer to use the PMIC's DRIVEVBUS function to control VBUS for
USB OTG, as that is the hardware default.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

In the past, all the MMC pins had

	allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;

which was actually a no-op. We were relying on U-boot to set the bias
pull up for us. These properties were removed as part of the fix up to
actually support no bias on the pins. During the transition some boards
experienced regular MMC time-outs during normal operation, while others
completely failed to initialize the SD card.

Given that MMC starts in open-drain mode and the pull-ups are required,
it's best to enable it for all the pin settings.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Now that we can handle the generic pinctrl bindings, convert our DT to it.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

The allwinner,pull property set to NO_PULL was really considered our
default (and wasn't even changing the default value in the code).

Remove these properties to make it obvious that we do not set anything in
such a case.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

The allwinner,drive property set to 10mA was really considered as our
default. Remove all those properties entirely to make that obvious.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

The SoC hix5hd2 compatible string has the suffix "-gmac" and
we should not change it.
We should only add the generic compatible string "hisi-gmac-v1".

Fixes: 0855950b

 ("ARM: dts: hix5hd2: add gmac generic compatible and clock names")
Signed-off-by: Dongpo Li <lidongpo@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Bug report from Debian [0] shows there's minor changed model of
Linkstation LS-GL that uses the 2nd SATA port of the SoC.
So it's necessary to enable two SATA ports, though for that specific
model only the 2nd one is used.

[0] https://bugs.debian.org/845611

Fixes: b1742ffa

 ("ARM: dts: orion5x: add device tree for buffalo linkstation ls-gl")
Reported-by: Ryan Tandy <ryan@nardis.ca>
Tested-by: Ryan Tandy <ryan@nardis.ca>
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

The eLCDIF IP of the i.MX 7 SoC knows multiple clocks and lists them
separately:

Clock      Clock Root              Description
apb_clk    MAIN_AXI_CLK_ROOT       AXI clock
pix_clk    LCDIF_PIXEL_CLK_ROOT    Pixel clock
ipg_clk_s  MAIN_AXI_CLK_ROOT       Peripheral access clock

All of them are switched by a single gate, which is part of the
IMX7D_LCDIF_PIXEL_ROOT_CLK clock. Hence using that clock also for
the AXI bus clock (clock-name "axi") makes sure the gate gets
enabled when accessing registers.

There seem to be no separate AXI display clock, and the clock is
optional. Hence remove the dummy clock.

This fixes kernel freezes when starting the X-Server (which
disables/re-enables the display controller).

Fixes: e8ed73f6

 ("ARM: dts: imx7d: add lcdif support")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

In a previous commit, I made a copy/paste error in the pinmux
definitions of UART3: PG{13,14} instead of PA{13,14}. This commit takes
care of that. I have tested this commit on Orange Pi PC and Orange Pi
Plus, and it works for these boards.

Fixes: e3d11d3c

 ("dts: sun8i-h3: add pinmux definitions for
UART2-3")

Signed-off-by: Jorik Jonker <jorik@kippendief.biz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Add gmac generic compatible and clock names.

Signed-off-by: Dongpo Li <lidongpo@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Added basic dts support for MicroZed board.

- UART
- SDHCI
- Ethernet

Cc: Soren Brinkmann <soren.brinkmann@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

The mmc controller in da850 supports high speed modes
so add cap-sd-highspeed and cap-mmc-highspeed.

Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>

This SoC has a separate pin controller for configuring pullup/pulldown
bias on groups of pins.

Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>

Several versions of DW DMAC have multi block transfers hardware
support. Hardware support of multi block transfers is disabled
by default if we use DT to configure DMAC and software emulation
of multi block transfers used instead.
Add multi-block property, so it is possible to enable hardware
multi block transfers (if present) via DT.

Switch from per device is_nollp variable to multi_block array
to be able enable/disable multi block transfers separately per
channel.

Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>

Currently the memory controller and master priorities drivers are
enabled in da850.dtsi. For boards for which there are no settings
defined, this makes these drivers emit error messages.

Disable the nodes in da850.dtsi and only enable them for da850-lcdk -
the only board that currently needs them.

Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>

In order to avoid Linux generating a random mac address on every boot,
add an ethernet0 alias that will allow u-boot to patch the dtb with
the MAC address programmed into the EEPROM.

Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>

Add PCIe support to the ARTPEC-6 SoC. This uses the existing
pcie-artpec6 driver.
So, all that is needed is device tree entries in the DTS.

Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Jesper Nilsson <jespern@axis.com>

Add PCIe support to the ARTPEC-6 SoC. This uses the existing
pcie-artpec6 driver.
So, all that is needed is device tree entries in the DTS.

Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Jesper Nilsson <jespern@axis.com>

This machine is an open hardware router by cz.nic driven by a
Marvell Armada 385.

Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Tomas Hlavacek <tmshlvck@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>

This patch fixes the following DTC warnings with W=1:

Warning (unit_address_vs_reg): Node /regulators/regulator@0 has a unit
name, but no reg property
Warning (unit_address_vs_reg): Node /regulators/regulator@1 has a unit
name, but no reg property
Warning (unit_address_vs_reg): Node /regulators/regulator@2 has a unit
name, but no reg property
Warning (unit_address_vs_reg): Node /regulators/regulator@3 has a unit
name, but no reg property
Warning (unit_address_vs_reg): Node /regulators/regulator@4 has a unit
name, but no reg property

Signed-off-by: Jisheng Zhang <jszhang@marvell.com>

Add xo entry to sdhc clock node on all qcom platforms.

Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

Add a device node for the Product Register, which provides SoC product
and revision information.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a device node for the Product Register, which provides SoC product
and revision information.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a device node for the Product Register, which provides SoC product
and revision information.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a device node for the Product Register, which provides SoC product
and revision information.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a device node for the Product Register, which provides SoC product
and revision information.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a device node for the Product Register, which provides SoC product
and revision information.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a device node for the Product Register, which provides SoC product
and revision information.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Define the SK-RZG1E board dependent part of the Ether device node.
Enable DHCP and NFS root  for the kernel booting.

Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add the initial  device tree for the R8A7745 SoC based SK-RZG1E board.
The board has 1  debug  serial  port (SCIF2); include support for it,
so that the serial console can  work.

Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Describe the IRQC interrupt controller in the R8A7745 device tree.

Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Define the generic R8A7745 part of the Ether device node.

Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Describe [H]SCIF{|A|B} ports in the R8A7745 device tree.

Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
[simon: consistently use tabs for indentation]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Describe SYS-DMAC0/1 in the R8A7745 device tree.

Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The  initial R8A7745 SoC device tree including CPU0, GIC, timer, SYSC, RST,
CPG, and the required clock descriptions.

Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Define the SK-RZG1M board dependent part of the Ether device node.
Enable DHCP and NFS root  for the kernel booting.

Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add the initial device  tree for the R8A7743 SoC based SK-RZG1M board.
The board has one debug serial port (SCIF0); include support for it, so
that  the serial  console  can work.

Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Describe the IRQC interrupt controller in the R8A7743 device tree.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Define the generic R8A7743 part of the Ether device node.

Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>