Remove commas from unit addresses as suggested by Rob Herring upon me
posting initial Apalis TK1 support:

	http://article.gmane.org/gmane.linux.ports.tegra/26608



Please keep the remaining 0, notation on the GPU node in place as a
former mainline U-Boot version was looking for that particular notation
in order to perform required fix-ups on it.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

This imports v11 of "Jetson TK1 Development Platform Pin Mux" from
https://developer.nvidia.com/embedded/downloads

.

The new version defines the mux option for the MIPI pad ctrl selection.
The OWR pin no longer has an entry in the configuration table because
the only mux option it support is OWR, that feature isn't supported, and
hence can't conflict with any other pin. This pin can only usefully be
used as a GPIO.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>

This seems to have been copied and pasted since the beginning of time,
though only until Tegra124, likely because that DT was written from
scratch or it was fixed along the way.

Signed-off-by: Thierry Reding <treding@nvidia.com>

Add unit-addresses to nodes that have a reg property to avoid warnings
on newer versions of DTC.

Signed-off-by: Thierry Reding <treding@nvidia.com>

The memory range assigned to the PMC (Power Management Controller) was
not including the PMC_PCR register which are used to control peripheral
clocks.

This was working fine thanks to the page granularity of ioremap(), but
started to fail when we switched to syscon/regmap, because regmap is
making sure that all accesses are falling into the reserved range.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: Richard Genoud <richard.genoud@gmail.com>
Tested-by: Richard Genoud <richard.genoud@gmail.com>
Fixes: 863a81c3 ("clk: at91: make use of syscon to share PMC registers in several drivers")
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

The device driver was added in v4.5 by commit dca536c4
("watchdog: add support for Sigma Designs SMP86xx/SMP87xx")

Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

This platform will use the new generic platdev driver.

Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Commit fefe0535 ("clk: tango4: improve clkgen driver") added
support for USB and SDIO clocks.

Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Define the CPU temperature sensor, and critical trip point.

Commit 799d71da471c ("add temperature sensor support for tango SoC")
added the device driver.

Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

An error in documentation of the NAND Flash Controller (NFC) led to choose
another compatibility string for sama5d2 with an impact on the NAND flash
ready/busy information. It was producing the error message:

atmel_nand 80000000.nand: Time out to wait for interrupt: 0x08000000

and had an impact on performance.

So, switch back to the classical "atmel,sama5d3-nfc" compatibility string for
this SoC which gives the proper ready/busy bit information. The NAND flash
driver will be updated to remove the support for this different
implementation.

Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Romain Izard <romain.izard.pro@gmail.com>
[nicolas.ferre@atmel.com: change commit message]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

This adds a common device tree for all fifth generation Aspeed systems,
and a board specific device tree for the ast2500 evaluation board.

Signed-off-by: Joel Stanley <joel@jms.id.au>

A common device tree for all forth gen/ast2400 systems and a board
specific dts for the Palmetto OpenPower developemnt machine which was
used for testing.

Signed-off-by: Joel Stanley <joel@jms.id.au>

Enable pll3 and pll7 clocks that are needed by display clocks.

Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

There are 3 kinds of OLinuXino Lime2 boards.
One without any on board storage, one with NAND storage and one with
eMMC storage. This patch adds the eMMC variant of boards.

eMMC storage is different from a regular SD card in that it is soldered
on the board and cannot be changed. Additionally, it shares pins with
the NAND module and with the second SPI port.

Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
[Maxime: Removed the change log from the commit log]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

MAX8997 PMIC requires interrupt and fails probing without it.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: d105f0b1 ("ARM: dts: Add basic dts file for Samsung Trats board")
Cc: <stable@vger.kernel.org>
[k.kozlowski: Write commit message, add CC-stable]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>

The usage of slash character causes failure when creating regulator
debugfs entry.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
[k.kozlowski: Write commit message]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>

The MFC nodes with the memory regions reserved for memory allocations
are missing in the Exynos5420 Peach Pit and Exynos5800 Peach Pi DTS.

This causes the s5p-mfc driver probe to fail with the following error:

[    4.140647] s5p_mfc_alloc_memdevs:1072: Failed to declare coherent memory for MFC device
[    4.216163] s5p-mfc: probe of 11000000.codec failed with error -12

Add the missing nodes so the driver probes and the {en,de}coder video
nodes are registered correctly:

[    4.096277] s5p-mfc 11000000.codec: decoder registered as /dev/video4
[    4.102282] s5p-mfc 11000000.codec: encoder registered as /dev/video5

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>

Add node to support SAMA5D4 hardware random number generator.

Signed-off-by: Mike Williams <mike@mikebwilliams.com>
[nicolas.ferre@atmel.com: reduce the register map size]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Add node to support SAMA5D3 hardware random number generator.

Signed-off-by: Mike Williams <mike@mikebwilliams.com>
[nicolas.ferre@atmel.com: reduce the register map size]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Add node to support SAMA5D2 hardware random number generator.

Signed-off-by: Mike Williams <mike@mikebwilliams.com>
[nicolas.ferre@atmel.com: reduce the register map size]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

No need to map 0x4000 bytes for the TRNG device: reduce it to 0x100.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Enable pll3 and pll7 clocks that are needed to drive display clocks.

Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The CHIP has a composite output available muxed with the microphone in the
micro-jack plug.

Enable the composite output in its DTS.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The TCON, tv-encoder and display engine backends and frontends are combined
to create our display pipeline.

Add them to the R8 DTSI. It's supposed to be perfectly compatible with the
A10s and A13, but since we haven't tested it on them yet, it's safer to
just enable it on the R8. Eventually, it should be moved to sun5i.dtsi

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Enable the display and TCON (channel 0 and channel 1) clocks that are going
to be needed to drive the display engine, tcon and TV encoders.

Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Configure the two accelerometers sharing GPIO line 82 as:

- Open drain so that they can share the same interrupt line.

Configure the corresponding interrupt pin:

- Trigger on the falling edge since open drain implies that we
  do not actively drive the line high, but we will actively drive
  it low to generate interrupts and then it moves from high to low
  i.e. a falling edge.

- Pulled up so the line will be biased to high unless an IRQ
  is active on any device on the line, and thus it goes high
  again after the interrupt is deasserted.

Cc: linux-iio@vger.kernel.org
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add USB OTG support to M53EVK instead of just USB gadget.

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

imx6ul-14x14-evk has a wm8960 codec connected via SAI2 port.

Add support for it.

Thanks to Petr Kulhavy <brain@jikos.cz> for the hint on initializing
the PLL4 frequency to get a correct MCLK.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The following build warnings are seen when building with 'W=1' option:

Warning (unit_address_vs_reg): Node /soc/aips-bus@02000000/anatop@020c8000/regulator-1p1@110 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /soc/aips-bus@02000000/anatop@020c8000/regulator-3p0@120 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /soc/aips-bus@02000000/anatop@020c8000/regulator-2p5@130 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /soc/aips-bus@02000000/anatop@020c8000/regulator-vddcore@140 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /soc/aips-bus@02000000/anatop@020c8000/regulator-vddpu@140 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /soc/aips-bus@02000000/anatop@020c8000/regulator-vddsoc@140 has a unit name, but no reg property

Fix them by removing the unneeded unit-addresses.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This patch adds the bus device tree nodes for INT (Internal) block
to enable the AMBA bus frequency scaling and add the NoC (Network on Chip)
Probe Device Tree node to measure the bandwidth for AMBA AXI bus.

The WCORE bus bus is parent device in INT block using VDD_INT.

Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>

This patch adds the AMBA bus nodes using VDD_INT for Exynos542x SoC.
Exynos542x has the following AMBA buses to translate data between
DRAM and sub-blocks.

Following list specifies the detailed correlation between sub-block and clock:
- CLK_DOUT_ACLK400_WCORE clock for WCORE's AXI
- CLK_DOUT_ACLK100_NOC for NoC (Network on Chip)'s AXI
- CLK_DOUT_PCLK200_FSYS for FSYS's APB
- CLK_DOUT_ACLK200_FSYS for FSYS's AXI
- CLK_DOUT_ACLK200_FSYS2 for FSYS2's AXI
- CLK_DOUT_ACLK333 for MFC's AXI
- CLK_DOUT_ACLK266 for GEN's AXI
- CLK_DOUT_ACLK66 for PERIC/PERIR's AXI
- CLK_DOUT_ACLK333_G2D for G2D's AXI
- CLK_DOUT_ACLK266_G2D for ACP's AXI
- CLK_DOUT_ACLK300_JPEG for JPEG's AXI
- CLK_DOUT_ACLK166 for JPEG's APB
- CLK_DOUT_ACLK300_DISP1 for FIMD's AXI
- CLK_DOUT_ACLK400_DISP1 for DISP1's AXI
- CLK_DOUT_ACLK300_GSCL for GSCL Scaler's AXI
- CLK_DOUT_ACLK400_MSCL for MSCL's AXI

Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>

This patch adds the NoCP (Network on Chip Probe) Device Tree node
to measure the bandwidth of memory and g3d in Exynos542x SoC.

Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>

This patch adds the bus device tree nodes for both MIF (Memory) and INT
(Internal) block to enable the bus frequency.

The DMC bus is parent device in MIF block using VDD_MIF and the LEFTBUS
bus is parent device in INT block using VDD_INT.

Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
[m.reichl and linux.amoon: Tested it on exynos4412-odroidu3 board]
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>

This patch expands the voltage range of buck1/3 regulator due to as following:
- MIF (Memory Interface) bus frequency needs the range of '900 - 1100 mV'.
- INT (Internal) bus frequency needs the range of '900 - 1050 mV'.

Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
[m.reichl and linux.amoon: Tested it on exynos4412-odroidu3 board]
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>

This patch adds the bus device-tree nodes of INT (internal) block
to enable the bus frequency scaling. The following sub-blocks share
the VDD_INT power source:
- LEFTBUS (parent device)
- RIGHTBUS
- PERIL
- LCD0
- FSYS
- MCUISP / ISP
- MFC

The LEFTBUS is parent device with devfreq ondemand governor
and the rest of devices depend on the LEFTBUS device.

Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>

This patch adds the exynos4412-ppmu-common.dtsi to remove duplicate PPMU nodes
because exynos3250-rinato/monk, exynos4412-trats2/odroidu3 has the same
PPMU device tree node.

Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
[m.reichl and linux.amoon: Tested it on exynos4412-odroidu3 board]
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>

This patch adds the bus nodes for Exynos4210 SoC. Exynos4210 SoC has
one power line for all buses to translate data between DRAM and sub-blocks.

Following list specifies the detailed relation between DRAM and sub-blocks:
- DMC/ACP clock for DMC (Dynamic Memory Controller)
- ACLK200 clock for LCD0
- ACLK100 clock for PERIL/PERIR/MFC(PCLK)
- ACLK160 clock for CAM/TV/LCD0/LCD1
- ACLK133 clock for FSYS/GPS
- GDL/GDR clock for LEFTBUS/RIGHTBUS
- SCLK_MFC clock for MFC

Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>

This patch adds the bus nodes using VDD_INT for Exynos4x12 SoC.
Exynos4x12 has the following AXI buses to translate data between
DRAM and sub-blocks.

Following list specifies the detailed relation between DRAM and sub-blocks:
- ACLK100 clock for PERIL/PERIR/MFC(PCLK)
- ACLK160 clock for CAM/TV/LCD
: The minimum clock of ACLK160 should be over 160MHz.
  When drop the clock under 160MHz, show the broken image.
- ACLK133 clock for FSYS
- GDL clock for LEFTBUS
- GDR clock for RIGHTBUS
- SCLK_MFC clock for MFC

Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
[m.reichl and linux.amoon: Tested it on exynos4412-odroidu3 board]
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>

This patch adds the bus nodes using VDD_MIF for Exynos4x12 SoC.
Exynos4x12 has the following AXI buses to translate data
between DRAM and DMC/ACP/C2C.

Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
[m.reichl and linux.amoon: Tested it on exynos4412-odroidu3 board]
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>

This patch adds the bus nodes using VDD_INT for Exynos3250 SoC.
Exynos3250 has following AXI buses to translate data between
DRAM and sub-blocks.

Following list specifies the detailed relation between DRAM and sub-blocks:
- ACLK400 clock for MCUISP
- ACLK266 clock for ISP
- ACLK200 clock for FSYS
- ACLK160 clock for LCD0
- ACLK100 clock for PERIL
- GDL clock for LEFTBUS
- GDR clock for RIGHTBUS
- SCLK_MFC clock for MFC

Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>