Add dts file to support Buffalo Linkstation LS-GL
(a.k.a Buffalo Linkstation Pro/Live), which is marvell orion5x based
3.5" HDD NAS.

Product info:
  - (JPN) http://buffalo.jp/products/catalog/item/l/ls-gl/
  - (ENG) http://www.buffalotech.com/products/network-storage/linkstation/linkstation-pro



This device tree is based on the board file:
  arch/arm/mach-orion5x/kurobox_pro-setup.c
However, that board file also support Kurobox Pro, which is not supported by
device tree yet. So the board file is not removed.

Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

Add dts file to support Buffalo Linkstation LS-QVL,
which is marvell kirkwood based 4-bay 3.5" HDD NAS.
Product info:
  - (JPN) http://buffalo.jp/product/hdd/network/ls-qvl_r5/
  - (ENG) http://www.buffalotech.com/products/network-storage/home-and-small-office/linkstation-pro-quad



Signed-off-by: Mario Lange <mario_lange@gmx.net>
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

LS-WVL/VL are both kirkwood-6282 based NAS devices, which share
many MPP pins. However they are slightly different:
  - LS-WVL is 2-Bay NAS, and LS-VL is only 1-Bay.
  - There're two red LED indicator on LS-WVL to show when HDD fails,
    which is similar to LS-WXL, but there's no such on LS-VL.

So after the split, common part goes into .dtsi file:
  - kirkwood-linkstation-6282.dtsi
while all rest part goes into device specific .dts file:
  - kirkwood-linkstation-lsvl.dts
  - kirkwood-linkstation-lswvl.dts

Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

LS-WXL/WSXL are both kirkwood-6281 based 2-Bay NAS devices, which share
many MPP pins. However they are slightly different:
  - There're two red LED indicator on LS-WXL to show when HDD fails,
    but there's no such on LS-WSXL.
  - There's 4-level speed adjustable FAN on LS-WXL, but not LS-WSXL.

So after the split, common part goes into .dtsi file:
  - kirkwood-linkstation.dtsi
  - kirkwood-linkstation-duo-6281.dtsi
while all rest part goes into device specific .dts file:
  - kirkwood-linkstation-lswsxl.dts
  - kirkwood-linkstation-lswxl.dts

Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

The Pi 2 B ends up like a Pi 1 B+, with the same peripherals and
pinout, but the CPU and memory layout changed to use the 2836.

Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

This allows us to boot dra62x j5-eco evm with NFSroot.

Signed-off-by: Tony Lindgren <tony@atomide.com>

This device tree was tested on a Sigma Designs SMP8758 Vantage-1172
Rev E1 development board.

Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

SBC-iMX7 is a single board computer designed for industrial
and embedded applications. It is based on the Freescale i.MX7
system-on-chip. SBC-iMX7 is implemented with the CL-SOM-iMX7
System-on-Module providing most of the functions, and SB-SOM-iMX7
carrier board providing additional peripheral functions and
connectors.

http://www.compulab.co.il/products/sbcs/sbc-imx7-freescale-i-mx-7-single-board-computer/

http://www.compulab.co.il/products/computer-on-modules/cl-som-imx7-freescale-i-mx-7-system-on-module/



Add basic board support, including SD card as a secondary boot and storage device

Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>

CL-SOM-iMX7 is a miniature System-on-Module (SoM) based on
Freescale i.MX7 System-on-Chip family.

http://www.compulab.co.il/products/computer-on-modules/cl-som-imx7-freescale-i-mx-7-system-on-module/



Add basic DT support for standalone module (without a carrier board):

* Memory configuration
* eMMC
* 2x Gigabit Ethernet ports (FEC1 and FEC2)
* I2C2 bus
  * EEPROM
  * PCA9555 GPIO extender
  * PMIC
* UART1
* USB OTG port

Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>

Novena is an open-hardware laptop/desktop/bare board.

See http://www.kosagi.com/w/index.php?title=Novena_Main_Page



Signed-off-by: Sean Cross <xobs@kosagi.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

This device tree adds support for TS-4800 by Technologic Systems. This
board is based on MX51-babbage, but there are some subtle differences in
the pins used, and there is an additional FPGA that is memory-mapped.

More details here:
  http://wiki.embeddedarm.com/wiki/TS-4800



Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

Minimal Cortex-M4 device tree to boot Linux to shell. M4 is booted via
Cortex-A5 running Linux using Stefan Agner's <stefan@agner.ch> "m4boot"
utility.

Signed-off-by: Afzal Mohammed <afzal.mohd.ma@gmail.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

The Empire Electronix D709 tablet is a fairly standard 7" A13 tablet,
featuring usb-wifi, a micro-sd slot, micro-usb otg and headphone jack.

Empire Electronix is written on the back of the tablet, the D709 model
info can be found in the about tablet menu in android.

The PCB has no markings to speak of.

This dts file does not add support for the ft5x touchscreen found at
i2c bus 1, addr 0x38, irq PG11, because it does not work out of the box.
It seems it has been flashed with the wrong firmware and needs to have
alternative firmware uploaded at boot to make the touchscreen work
properly, when hot-booting from android into an upstream kernel the
touchscreen does work.

The Memsic MXC622X accelerometer at i2c bus 1, addr 0x15 also is not
enabled as there is no driver for it.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

The Versatile Industrial Communication platform is a community oriented
board from Landis + Gyr. It comes with:
      - an RS-485 port
      - 2 Ethernet ports
      - a wireless M-BUS
      - a 4G modem
      - a 4MB SPI flash
      - a 4GB eMMC

Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>

This patchset is the initiation version to try work
for kylin board.

Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Add basic support for the SBC-T335.

CompuLab SBC-T335 is a single baseboard computer.
The SBC-T335 is based on the Texas Instruments Cortex-A8 Sitara AM3354
SoC.

Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This adds a device tree for the CloudEngines PogoPlug series 4
NAS device. Inspired by out-of-tree boardfiles from ArchLinux
by Kevin Mihelich.

Cc: Moonman <moonman.ca@gmail.com>
Cc: Kevin Mihelich <kevin@archlinuxarm.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

Add a new DTS file to support the Zyxel NSA325(v2) dual bay
NAS device, based on the NSA320 DTS files.

The only difference to the NSA320 device is GPIO47.
This en/disables the power for the hdd in slot2, currently
fixed to on.

[gregory.clement@free-electrons.com: fix comment format]
Signed-off-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

Add support for the DENX MA5D4 SoM and MA5D4EVK board. The system
consists of a SoM with eMMC, SPI NOR for booting, 2x SPI CAN chip
and an EVK with microSD slot, 2x UART, 2x CAN port, 3x USB port,
LEDs and expansion headers.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

This adds a device tree for the ARM RealView ARM11MPCore
reference design.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Initial release for rk3228 sdk board.

Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

This introduces initial support for the Sony Xperia Z smartphone, including
support for UART, MMC, USB gadget and physical buttons.

Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Andy Gross <agross@codeaurora.org>

Add support for the SolidRun Armada 388 Clearfog A1 board.  This board
has an Armada 388 microsom, dedicated gigabit ethernet, six switched
gigabit ethernet ports, SFP cage, two Mini-PCIe/mSATA slots, a m.2 SATA
slot, and a MikroBUS connector to allow MikroBUS modules to be added.

This DT file adds support for all board facilities with the exception
of full SFP support.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

The Orange Pi Plus is a SBC based on the Allwinner H3 SoC
with 8GB eMMC, multiple USB ports through a USB hub chip, SATA through
a USB-SATA bridge, one uSD slot, a 10/100/1000M ethernet port,
WiFi, HDMI, headphone jack, IR receiver, a microphone, a CSI connector
and a 40-pin GPIO header.

Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

SBC-AM57x is a single board computer designed for industrial and
embedded applications. It is based on the Texas Instruments Sitara AM57x
system-on-chip family. SBC-AM57x is implemented with the CL-SOM-AM57x
computer-on-module providing most of the functions, and SB-SOM-AM57x
carrier board providing additional peripheral functions and connectors.

https://www.compulab.co.il/products/sbcs/sbc-am57x-ti-am5728-am5718-single-board-computer/

https://www.compulab.co.il/products/computer-on-modules/cl-som-am57x-ti-am5728-am5718-system-on-module/



Add basic board support, including UART3, used as a serial console.

Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add support for CompuLab CM-SOM-AM57X board.

CL-SOM-AM57x is a miniature System-on-Module (SoM) based on
TI Sitara AM57x ARM Cortex-A15 System-on-Chip family.

https://www.compulab.co.il/products/computer-on-modules/cl-som-am57x-ti-am5728-am5718-system-on-module/



Add basic DT support for standalone module (without a carrier board):

* Memory configuration
* Heartbeat led
* I2C1 and I2C4
* PMIC
* SATA

Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add basic support for SBC-T43: a CM-T43 based single board computer.
CM-T43 is an AM437x based System-on-Module designed to serve as a building
block in embedded applications. SBC-T43 is composed of CM-T43 module on
top of the SB-SOM-T43 baseboard.
Basic support includes UART, GPIO, and I2C.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Also known as the Asus Chromebit.

Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Tested-by: Caesar Wang <wxt@rock-chips.com>
For the license change:
Acked-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Similar to pinky, brain is a development model and probably also
nearing extinction. But to keep pinky from being lonely I'll keep
the two brain boards around as well, especially as they as well
have easily accessible dut-connectors.

Signed-off-by: Heiko Stuebner <heiko.stuebner@collabora.com>
For the license change:
Acked-by: Brian Norris <briannorris@chromium.org>

add support for the am335x based shc board.

UART: 0-2 and 4
DRAM: 512 MiB
MMC:  OMAP SD/MMC: 0 @ 26 MHz
      OMAP SD/MMC: 1 @ 26 MHz
I2C:  at24 eeprom, pcf8563
USB:  USB1 (host)

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add basic support for CompuLab cm-t335 module based on AM335X SoC.

CM-T335 is a tiny computer-on-module (CoM) / system-on-module (SoM)
The module is built around the Texas Instruments Sitara AM3352/4
system-on-chip.

The CPU is supplemented with up-to 512MB DDR3 and up-to 1GB of on-board
NAND storage, WiFi connected to SPI, Bluetooth, Analog audio, Gigabit
Ethernet, CAN bus.

Current patch adds support:
UART0 and GPIO LED

Detailed description can be found at the module site:
http://www.compulab.co.il/products/computer-on-modules/cm-t335/



Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
[uri.mashiach@compulab.co.il: the default RAM amount reduced to
128MB to support also the minimal module configuration]
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Initial release for rk3036 sdk board.

Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

This adds basic chip support for Mediatek 2701.

Signed-off-by: Erin Lo <erin.lo@mediatek.com>
[matthias.bgg@gmail.com: Fixed reg address of mt2701-timer]
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>

Add support for the DENX MCV SoM and MCVEVK baseboard. The SoM contains
eMMC, DRAM, Altera Cyclone V SoC. The baseboard contains CAN ports, UART
ports, STMPE811 touchscreen controller, USB OTG port, ethernet port and
a lot of IO pins.

Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: Vince Bridgers <vbridgers2013@gmail.com>
Cc: Alan Tull <atull@altera.com>
Cc: Thor Thayer <tthayer@altera.com>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>

This baseboard from SWAC is equipped with the ICnova-A20 SoM from
Incircuit. This board is equipped with the following interfaces /
devices:

- 512 MiB SDRAM
- 4 GiB MLC NAND (Micron MT29F32G08CBACAWP or Hynix H27UBG8T2BTR)
- USB host
- LCD 800x480
- HDMI
- CAN

Note that the NAND support is still missing. As its currently not
supported in mainline for sunxi and especially for these MLC
devices.

The original plan was to also provide a dtsi for the ICnova SoM,
to put all the SoM internal nodes / properties there. But as I
don't have a clear overview of the SoM specific and baseboard
specific differences, I'm putting all in one dts for now. Once
somebody pushed support for some other baseboard using the
A20 SoM from Incircuit (e.g. the ADB4006 reference design), this
should be separated.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marcus Heuer <marcus.heuer@swac.de>
[maxime: Fixed CPU regulator upper voltage boundary]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Add device tree files for Broadcom Northstar based SVKs.  Since the
bcm5301x.dtsi already exists, all that is necessary is the dts files to
enable the UARTs.  With these files, the SVKs are able to boot to shell.

Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

The Henninger low cost board was never sold and so  had  no  users outside
Renesas (and Cogent Embedded). Instead Renesas  has made the Porter  board
which has mostly similar hardware. Now that the Porter board support is on
par with Henninger, we can remove  the Henninger's device tree file.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Enable building all dtb files when CONFIG_OF_ALL_DTBS is enabled. The dtbs
are not really dependent on a platform being enabled or any other kernel
config, so for testing coverage it is convenient to build all of the dtbs.
This builds all dts files in the tree, not just targets listed. This
is simpler for arm64 which has a bunch of sub-dirs.

Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>

Initial version of DTS for ProXstream2 Vodka board.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Initial version of DTS for ProXstream2 Gentil board.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>