pinctrl: bcm2712: Reject invalid pulls

Reject attempts to set pulls on aon-sgpios, and fix pull shift
values.

pinctrl: bcm2712: Add 7712 support, fix 2712 count

Signed-off-by: Phil Elwell <phil@raspberrypi.com>

pinctrl-bcm2712: add EMMC pins so pulls can be set

These pins have pad controls but not mux controls. They look enough like
GPIOs to squeeze in at the end of the list though.

pinctrl: bcm2712: correct BCM2712C0 AON_GPIO pad pull control offset

Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>

pinctrl: bcm2712: on C0 the regular GPIO pad control register moves too

Signed-off-by: Jonathan Bell <jonathan@raspberrypi.com>

pinctrl: bcm2712: Implement (partially) pinconf_get

Signed-off-by: Phil Elwell <phil@raspberrypi.com>

pinctrl: bcm2712: Convert to generic pinconf

Remove the legacy brcm,* pin configuration support and replace it with
a proper generic pinconf interface, using named functions instead of
alt function numbers. This is nicer for users, less error-prone, and
immune to some of the C0->D0 changes.

Signed-off-by: Phil Elwell <phil@raspberrypi.com>

pinctrl: bcm2712: Remove vestigial pull parameter

Now the legacy brcm, pinconf parameters are no longer supported, this
custom pin config parameter is not needed.

Signed-off-by: Phil Elwell <phil@raspberrypi.com>

pinctrl: bcm2712: Guard against bad func numbers

Signed-off-by: Phil Elwell <phil@raspberrypi.com>

pinctrl: bcm2712: A better attempt at D0 support

The BCM2712D0 sparse pinctrl maps play havoc with the old GPIO_REGS
macro, so make the bit positions explicit. And delete the unwanted
GPIO and pinmux declarations on D0.

Note that a Pi 5 with D0 requires a separate DTS file with "bcm2712d0"
compatible strings.

Signed-off-by: Phil Elwell <phil@raspberrypi.com>

pinctrl: bcm2712: Delete base register constants

BCM2712D0 deletes many GPIOs and their associated mux and pad bits,
so much so that the offsets to the start of the pad control registers
changes. Remove the constant offsets from the *GPIO_REGS macros,
compensating by adjusting the per-GPIO values.

Signed-off-by: Phil Elwell <phil@raspberrypi.com>

gpio-brcmstb: Report the correct bank width

gpio: brcmstb: Use bank address as gpiochip label

If the path to the device node is used as gpiochip label then
gpio-brcmstb instances with multiple banks end up with duplicated
names. Instead, use a combination of the driver name with the physical
address of the bank, which is both unique and helpful for devmem
debugging.

Signed-off-by: Phil Elwell <phil@raspberrypi.com>

gpio: mmio: Add DIRECT mode for shared access

The generic MMIO GPIO library uses shadow registers for efficiency,
but this breaks attempts by raspi-gpio to change other GPIOs in the
same bank. Add a DIRECT mode that makes fewer assumptions about the
existing register contents, but note that genuinely simultaneous
accesses are likely to lose updates.

Signed-off-by: Phil Elwell <phil@raspberrypi.com>

gpio: brcmstb: Don't always clear interrupt mask

If the GPIO controller is not being used as an interrupt source
leave the interrupt mask register alone. On BCM2712 it might be used
to generate interrupts to the VPU firmware, and on other devices it
doesn't matter since no interrupts will be generated.

Signed-off-by: Phil Elwell <phil@raspberrypi.com>

dtoverlays: Fix up edt5406 entries to match with vc4-kms-dsi-7inch

vc4-kms-dsi-7inch expects the touch fragment to be named ts_i2c_frag,
but edt5406 didn't do this.

Fixes: 736d601fb38c ("dts: 2712: Update for device tree")

Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>

This reverts commit c0ea202f.

The HAT map is way of associating named overlays with HATs whose
EEPROMs were programmed with the contents of the overlay.
Unfortunately, change in the DT and kernel drivers has meant that some
of these embedded overlays no longer function, or even don't apply.

The HAT map is a mapping from HAT UUIDs to overlay names. If a HAT with
a listed UUID is detected, the embedded overlay is ignored and the
overlay named in the mapping is loaded in its place.

Signed-off-by: Phil Elwell <phil@raspberrypi.com>

This reverts commit 2bcf744d.

Hardware that fails to read the edid is quite common.
The kernel provides a mechanism to use one a of a few
pre-built generic edid files for getting a basic video mode.

However there is no easy was to add basic audio support,
which requires a CTA extension block to report capabilities.

Add an module option to request this.

Signed-off-by: Dom Cobley <popcornmix@gmail.com>

Link: https://lore.kernel.org/r/20230917191040.964416434@linuxfoundation.org


Tested-by: SeongJae Park <sj@kernel.org>
Tested-by: Takeshi Ogasawara <takeshi.ogasawara@futuring-girl.com>
Tested-by: Bagas Sanjaya <bagasdotme@gmail.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Tested-by: Ron Economos <re@w6rz.net>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Salvatore Bonaccorso <carnil@debian.org>
Tested-by: Florian Fainelli <florian.fainelli@broadcom.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Tested-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 3d028d5d upstream.

[WHY]
Currently, when insert_plane is called with insert_above_mpcc
parameter that is equal to tree->opp_list, the function returns NULL.

[HOW]
Instead, the function should insert the plane at the top of the tree.

Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Wesley Chalmers <wesley.chalmers@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 4fe4a637 upstream.

We have originally guarded fiddling with CHECKFLAGS in our arch Makefile
by checking for the CONFIG_MIPS variable, not set for targets such as
`distclean', etc. that neither include `.config' nor use the compiler.

Starting from commit 805b2e1d ("kbuild: include Makefile.compiler
only when compiler is needed") we have had a generic `need-compiler'
variable explicitly telling us if the compiler will be used and thus its
capabilities need to be checked and expressed in the form of compilation
flags.  If this variable is not set, then `make' functions such as
`cc-option' are undefined, causing all kinds of weirdness to happen if
we expect specific results to be returned, most recently:

cc1: error: '-mloongson-mmi' must be used with '-mhard-float'

messages with configurations such as `fuloong2e_defconfig' and the
`modules_install' target, which does include `.config' and yet does not
use the compiler.

Replace the check for CONFIG_MIPS with one for `need-compiler' instead,
so as to prevent the compiler from being ever called for CHECKFLAGS when
not needed.

Reported-by: Guillaume Tucker <guillaume.tucker@collabora.com>
Closes: https://lore.kernel.org/r/85031c0c-d981-031e-8a50-bc4fad2ddcd8@collabora.com/


Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Fixes: 805b2e1d ("kbuild: include Makefile.compiler only when compiler is needed")
Cc: stable@vger.kernel.org # v5.13+
Reported-by: "kernelci.org bot" <bot@kernelci.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit a22730b1 ]

syzkaller found a memory leak in kcm_sendmsg(), and commit c821a88b
("kcm: Fix memory leak in error path of kcm_sendmsg()") suppressed it by
updating kcm_tx_msg(head)->last_skb if partial data is copied so that the
following sendmsg() will resume from the skb.

However, we cannot know how many bytes were copied when we get the error.
Thus, we could mess up the MSG_MORE queue.

When kcm_sendmsg() fails for SOCK_DGRAM, we should purge the queue as we
do so for UDP by udp_flush_pending_frames().

Even without this change, when the error occurred, the following sendmsg()
resumed from a wrong skb and the queue was messed up.  However, we have
yet to get such a report, and only syzkaller stumbled on it.  So, this
can be changed safely.

Note this does not change SOCK_SEQPACKET behaviour.

Fixes: c821a88b ("kcm: Fix memory leak in error path of kcm_sendmsg()")
Fixes: ab7ac4eb ("kcm: Kernel Connection Multiplexor module")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://lore.kernel.org/r/20230912022753.33327-1-kuniyu@amazon.com


Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 3c44191d ]

The commit in fixes introduced flags to control the status of hardware
configuration while processing packets. At the same time another structure
is used to provide configuration of timestamper to user-space applications.
The way it was coded makes this structures go out of sync easily. The
repro is easy for 82599 chips:

[root@hostname ~]# hwstamp_ctl -i eth0 -r 12 -t 1
current settings:
tx_type 0
rx_filter 0
new settings:
tx_type 1
rx_filter 12

The eth0 device is properly configured to timestamp any PTPv2 events.

[root@hostname ~]# hwstamp_ctl -i eth0 -r 1 -t 1
current settings:
tx_type 1
rx_filter 12
SIOCSHWTSTAMP failed: Numerical result out of range
The requested time stamping mode is not supported by the hardware.

The error is properly returned because HW doesn't support all packets
timestamping. But the adapter->flags is cleared of timestamp flags
even though no HW configuration was done. From that point no RX timestamps
are received by user-space application. But configuration shows good
values:

[root@hostname ~]# hwstamp_ctl -i eth0
current settings:
tx_type 1
rx_filter 12

Fix the issue by applying new flags only when the HW was actually
configured.

Fixes: a9763f3c ("ixgbe: Update PTP to support X550EM_x devices")
Signed-off-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit c48ef9c4 ]

Since bhash2 was introduced, the example below does not work as expected.
These two bind() should conflict, but the 2nd bind() now succeeds.

  from socket import *

  s1 = socket(AF_INET6, SOCK_STREAM)
  s1.bind(('::ffff:127.0.0.1', 0))

  s2 = socket(AF_INET, SOCK_STREAM)
  s2.bind(('127.0.0.1', s1.getsockname()[1]))

During the 2nd bind() in inet_csk_get_port(), inet_bind2_bucket_find()
fails to find the 1st socket's tb2, so inet_bind2_bucket_create() allocates
a new tb2 for the 2nd socket.  Then, we call inet_csk_bind_conflict() that
checks conflicts in the new tb2 by inet_bhash2_conflict().  However, the
new tb2 does not include the 1st socket, thus the bind() finally succeeds.

In this case, inet_bind2_bucket_match() must check if AF_INET6 tb2 has
the conflicting v4-mapped-v6 address so that inet_bind2_bucket_find()
returns the 1st socket's tb2.

Note that if we bind two sockets to 127.0.0.1 and then ::FFFF:127.0.0.1,
the 2nd bind() fails properly for the same reason mentinoed in the previous
commit.

Fixes: 28044fc1 ("net: Add a bhash2 table hashed by port and address")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Andrei Vagin <avagin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit aa99e5f8 ]

Andrei Vagin reported bind() regression with strace logs.

If we bind() a TCPv6 socket to ::FFFF:0.0.0.0 and then bind() a TCPv4
socket to 127.0.0.1, the 2nd bind() should fail but now succeeds.

  from socket import *

  s1 = socket(AF_INET6, SOCK_STREAM)
  s1.bind(('::ffff:0.0.0.0', 0))

  s2 = socket(AF_INET, SOCK_STREAM)
  s2.bind(('127.0.0.1', s1.getsockname()[1]))

During the 2nd bind(), if tb->family is AF_INET6 and sk->sk_family is
AF_INET in inet_bind2_bucket_match_addr_any(), we still need to check
if tb has the v4-mapped-v6 wildcard address.

The example above does not work after commit 5456262d ("net: Fix
incorrect address comparison when searching for a bind2 bucket"), but
the blamed change is not the commit.

Before the commit, the leading zeros of ::FFFF:0.0.0.0 were treated
as 0.0.0.0, and the sequence above worked by chance.  Technically, this
case has been broken since bhash2 was introduced.

Note that if we bind() two sockets to 127.0.0.1 and then ::FFFF:0.0.0.0,
the 2nd bind() fails properly because we fall back to using bhash to
detect conflicts for the v4-mapped-v6 address.

Fixes: 28044fc1 ("net: Add a bhash2 table hashed by port and address")
Reported-by: Andrei Vagin <avagin@google.com>
Closes: https://lore.kernel.org/netdev/ZPuYBOFC8zsK6r9T@google.com/


Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit c6d27706 ]

This is a prep patch to make the following patches cleaner that touch
inet_bind2_bucket_match() and inet_bind2_bucket_match_addr_any().

Both functions have duplicated comparison for netns, port, and l3mdev.
Let's factorise them.

Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: aa99e5f8 ("tcp: Fix bind() regression for v4-mapped-v6 wildcard address.")
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 8cdc3223 ]

Some code defines the IPv6 wildcard address as a local variable and
use it with memcmp() or ipv6_addr_equal().

Let's use in6addr_any and ipv6_addr_any() instead.

Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: aa99e5f8 ("tcp: Fix bind() regression for v4-mapped-v6 wildcard address.")
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 8cdd9f1a ]

ip6_sock_set_addr_preferences() second argument should be an integer.

SUNRPC attempts to set IPV6_PREFER_SRC_PUBLIC were
translated to IPV6_PREFER_SRC_TMP

Fixes: 18d5ad62 ("ipv6: add ip6_sock_set_addr_preferences")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230911154213.713941-1-edumazet@google.com


Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 403f0e77 ]

macb_set_tx_clk() is called under a spinlock but itself calls clk_set_rate()
which can sleep. This results in:

| BUG: sleeping function called from invalid context at kernel/locking/mutex.c:580
| pps pps1: new PPS source ptp1
| in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 40, name: kworker/u4:3
| preempt_count: 1, expected: 0
| RCU nest depth: 0, expected: 0
| 4 locks held by kworker/u4:3/40:
|  #0: ffff000003409148
| macb ff0c0000.ethernet: gem-ptp-timer ptp clock registered.
|  ((wq_completion)events_power_efficient){+.+.}-{0:0}, at: process_one_work+0x14c/0x51c
|  #1: ffff8000833cbdd8 ((work_completion)(&pl->resolve)){+.+.}-{0:0}, at: process_one_work+0x14c/0x51c
|  #2: ffff000004f01578 (&pl->state_mutex){+.+.}-{4:4}, at: phylink_resolve+0x44/0x4e8
|  #3: ffff000004f06f50 (&bp->lock){....}-{3:3}, at: macb_mac_link_up+0x40/0x2ac
| irq event stamp: 113998
| hardirqs last  enabled at (113997): [<ffff800080e8503c>] _raw_spin_unlock_irq+0x30/0x64
| hardirqs last disabled at (113998): [<ffff800080e84478>] _raw_spin_lock_irqsave+0xac/0xc8
| softirqs last  enabled at (113608): [<ffff800080010630>] __do_softirq+0x430/0x4e4
| softirqs last disabled at (113597): [<ffff80008001614c>] ____do_softirq+0x10/0x1c
| CPU: 0 PID: 40 Comm: kworker/u4:3 Not tainted 6.5.0-11717-g9355ce8b2f50-dirty #368
| Hardware name: ... ZynqMP ... (DT)
| Workqueue: events_power_efficient phylink_resolve
| Call trace:
|  dump_backtrace+0x98/0xf0
|  show_stack+0x18/0x24
|  dump_stack_lvl+0x60/0xac
|  dump_stack+0x18/0x24
|  __might_resched+0x144/0x24c
|  __might_sleep+0x48/0x98
|  __mutex_lock+0x58/0x7b0
|  mutex_lock_nested+0x24/0x30
|  clk_prepare_lock+0x4c/0xa8
|  clk_set_rate+0x24/0x8c
|  macb_mac_link_up+0x25c/0x2ac
|  phylink_resolve+0x178/0x4e8
|  process_one_work+0x1ec/0x51c
|  worker_thread+0x1ec/0x3e4
|  kthread+0x120/0x124
|  ret_from_fork+0x10/0x20

The obvious fix is to move the call to macb_set_tx_clk() out of the
protected area. This seems safe as rx and tx are both disabled anyway at
this point.
It is however not entirely clear what the spinlock shall protect. It
could be the read-modify-write access to the NCFGR register, but this
is accessed in macb_set_rx_mode() and macb_set_rxcsum_feature() as well
without holding the spinlock. It could also be the register accesses
done in mog_init_rings() or macb_init_buffers(), but again these
functions are called without holding the spinlock in macb_hresp_error_task().
The locking seems fishy in this driver and it might deserve another look
before this patch is applied.

Fixes: 633e98a7 ("net: macb: use resolved link config in mac_link_up()")
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20230908112913.1701766-1-s.hauer@pengutronix.de


Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit ee4e92c2 ]

Enable transmission and reception of PTP unicast packets by
updating PTP unicast config bit and setting current HW mac
address as allowed address in PTP unicast filter registers.

Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 403f0e77 ("net: macb: fix sleep inside spinlock")
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit cfaa80c9 ]

I got the below warning when do fuzzing test:
BUG: KASAN: null-ptr-deref in scatterwalk_copychunks+0x320/0x470
Read of size 4 at addr 0000000000000008 by task kworker/u8:1/9

CPU: 0 PID: 9 Comm: kworker/u8:1 Tainted: G           OE
Hardware name: linux,dummy-virt (DT)
Workqueue: pencrypt_parallel padata_parallel_worker
Call trace:
 dump_backtrace+0x0/0x420
 show_stack+0x34/0x44
 dump_stack+0x1d0/0x248
 __kasan_report+0x138/0x140
 kasan_report+0x44/0x6c
 __asan_load4+0x94/0xd0
 scatterwalk_copychunks+0x320/0x470
 skcipher_next_slow+0x14c/0x290
 skcipher_walk_next+0x2fc/0x480
 skcipher_walk_first+0x9c/0x110
 skcipher_walk_aead_common+0x380/0x440
 skcipher_walk_aead_encrypt+0x54/0x70
 ccm_encrypt+0x13c/0x4d0
 crypto_aead_encrypt+0x7c/0xfc
 pcrypt_aead_enc+0x28/0x84
 padata_parallel_worker+0xd0/0x2dc
 process_one_work+0x49c/0xbdc
 worker_thread+0x124/0x880
 kthread+0x210/0x260
 ret_from_fork+0x10/0x18

This is because the value of rec_seq of tls_crypto_info configured by the
user program is too large, for example, 0xffffffffffffff. In addition, TLS
is asynchronously accelerated. When tls_do_encryption() returns
-EINPROGRESS and sk->sk_err is set to EBADMSG due to rec_seq overflow,
skmsg is released before the asynchronous encryption process ends. As a
result, the UAF problem occurs during the asynchronous processing of the
encryption module.

If the operation is asynchronous and the encryption module returns
EINPROGRESS, do not free the record information.

Fixes: 635d9398 ("net/tls: free record only on encryption error")
Signed-off-by: Liu Jian <liujian56@huawei.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://lore.kernel.org/r/20230909081434.2324940-1-liujian56@huawei.com


Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 0a138f16 ]

The only probing method supported by the Nvidia SN2201 platform driver
is probing through an ACPI match table.  Hence add a dependency on
ACPI, to prevent asking the user about this driver when configuring a
kernel without ACPI support.

Fixes: 662f2482 ("platform/mellanox: Add support for new SN2201 system")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Vadim Pasternak <vadimp@nvidia.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/ec5a4071691ab08d58771b7732a9988e89779268.1693828363.git.geert+renesas@glider.be


Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 0f596945 ]

This fix involves 2 changes:
 - All event regs have a reset value of 0, which is not a valid
   event_number as per the event_list for most blocks and hence seen
   as an error. Add a "disable" event with event_number 0 for all blocks.

 - The enable bit for each counter need not be checked before
   reading the event info, and hence removed.

Fixes: 1a218d31 ("platform/mellanox: mlxbf-pmc: Add Mellanox BlueField PMC driver")
Signed-off-by: Shravan Kumar Ramani <shravankr@nvidia.com>
Reviewed-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: David Thompson <davthompson@nvidia.com>
Link: https://lore.kernel.org/r/04d0213932d32681de1c716b54320ed894e52425.1693917738.git.shravankr@nvidia.com


Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 80ccd405 ]

Replace sprintf with sysfs_emit where possible.
Size check in mlxbf_pmc_event_list_show should account for "\0".

Fixes: 1a218d31 ("platform/mellanox: mlxbf-pmc: Add Mellanox BlueField PMC driver")
Signed-off-by: Shravan Kumar Ramani <shravankr@nvidia.com>
Reviewed-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: David Thompson <davthompson@nvidia.com>
Link: https://lore.kernel.org/r/bef39ef32319a31b32f999065911f61b0d3b17c3.1693917738.git.shravankr@nvidia.com


Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit fc4c6558 ]

This commit drops over-sized network packets to avoid tmfifo
queue stuck.

Fixes: 1357dfd7 ("platform/mellanox: Add TmFifo driver for Mellanox BlueField Soc")
Signed-off-by: Liming Sun <limings@nvidia.com>
Reviewed-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: David Thompson <davthompson@nvidia.com>
Link: https://lore.kernel.org/r/9318936c2447f76db475c985ca6d91f057efcd41.1693322547.git.limings@nvidia.com


Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 78034cbe ]

This commit fixes tmfifo console stuck issue when the virtual
networking interface is in down state. In such case, the network
Rx descriptors runs out and causes the Rx network packet staying
in the head of the tmfifo thus blocking the console packets. The
fix is to drop the Rx network packet when no more Rx descriptors.
Function name mlxbf_tmfifo_release_pending_pkt() is also renamed
to mlxbf_tmfifo_release_pkt() to be more approperiate.

Fixes: 1357dfd7 ("platform/mellanox: Add TmFifo driver for Mellanox BlueField Soc")
Signed-off-by: Liming Sun <limings@nvidia.com>
Reviewed-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: David Thompson <davthompson@nvidia.com>
Link: https://lore.kernel.org/r/8c0177dc938ae03f52ff7e0b62dbeee74b7bec09.1693322547.git.limings@nvidia.com


Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit c821a88b ]

syzbot reported a memory leak like below:

BUG: memory leak
unreferenced object 0xffff88810b088c00 (size 240):
  comm "syz-executor186", pid 5012, jiffies 4294943306 (age 13.680s)
  hex dump (first 32 bytes):
    00 89 08 0b 81 88 ff ff 00 00 00 00 00 00 00 00  ................
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<ffffffff83e5d5ff>] __alloc_skb+0x1ef/0x230 net/core/skbuff.c:634
    [<ffffffff84606e59>] alloc_skb include/linux/skbuff.h:1289 [inline]
    [<ffffffff84606e59>] kcm_sendmsg+0x269/0x1050 net/kcm/kcmsock.c:815
    [<ffffffff83e479c6>] sock_sendmsg_nosec net/socket.c:725 [inline]
    [<ffffffff83e479c6>] sock_sendmsg+0x56/0xb0 net/socket.c:748
    [<ffffffff83e47f55>] ____sys_sendmsg+0x365/0x470 net/socket.c:2494
    [<ffffffff83e4c389>] ___sys_sendmsg+0xc9/0x130 net/socket.c:2548
    [<ffffffff83e4c536>] __sys_sendmsg+0xa6/0x120 net/socket.c:2577
    [<ffffffff84ad7bb8>] do_syscall_x64 arch/x86/entry/common.c:50 [inline]
    [<ffffffff84ad7bb8>] do_syscall_64+0x38/0xb0 arch/x86/entry/common.c:80
    [<ffffffff84c0008b>] entry_SYSCALL_64_after_hwframe+0x63/0xcd

In kcm_sendmsg(), kcm_tx_msg(head)->last_skb is used as a cursor to append
newly allocated skbs to 'head'. If some bytes are copied, an error occurred,
and jumped to out_error label, 'last_skb' is left unmodified. A later
kcm_sendmsg() will use an obsoleted 'last_skb' reference, corrupting the
'head' frag_list and causing the leak.

This patch fixes this issue by properly updating the last allocated skb in
'last_skb'.

Fixes: ab7ac4eb ("kcm: Kernel Connection Multiplexor module")
Reported-and-tested-by:  <syzbot+6f98de741f7dbbfc4ccb@syzkaller.appspotmail.com>
Closes: https://syzkaller.appspot.com/bug?extid=6f98de741f7dbbfc4ccb


Signed-off-by: Shigeru Yoshida <syoshida@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit a7b8d60b ]

According to the document of napi, there is no rx process when the
budget is 0. Therefore, r8152_poll() has to return 0 directly when the
budget is equal to 0.

Fixes: d2187f8e ("r8152: divide the tx and rx bottom functions")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 86899e9e ]

Currently, when we add the first sja1105 port to a bridge with
vlan_filtering 1, then we sometimes see this output:

sja1105 spi2.2: port 4 failed to read back entry for be:79:b4:9e:9e:96 vid 3088: -ENOENT
sja1105 spi2.2: Reset switch and programmed static config. Reason: VLAN filtering
sja1105 spi2.2: port 0 failed to add be:79:b4:9e:9e:96 vid 0 to fdb: -2

It is because sja1105_fdb_add() runs from the dsa_owq which is no longer
serialized with switch resets since it dropped the rtnl_lock() in the
blamed commit.

Either performing the FDB accesses before the reset, or after the reset,
is equally fine, because sja1105_static_fdb_change() backs up those
changes in the static config, but FDB access during reset isn't ok.

Make sja1105_static_config_reload() take the fdb_lock to fix that.

Fixes: 0faf890f ("net: dsa: drop rtnl_lock from dsa_slave_switchdev_event_work")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit ea32690d ]

sja1105_fdb_add() runs from the dsa_owq, and sja1105_port_mcast_flood()
runs from switchdev_deferred_process_work(). Prior to the blamed commit,
they used to be indirectly serialized through the rtnl_lock(), which
no longer holds true because dsa_owq dropped that.

So, it is now possible that we traverse the static config BLK_IDX_L2_LOOKUP
elements concurrently compared to when we change them, in
sja1105_static_fdb_change(). That is not ideal, since it might result in
data corruption.

Introduce a mutex which serializes accesses to the hardware FDB and to
the static config elements for the L2 Address Lookup table.

I can't find a good reason to add locking around sja1105_fdb_dump().
I'll add it later if needed.

Fixes: 0faf890f ("net: dsa: drop rtnl_lock from dsa_slave_switchdev_event_work")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 7cef293b ]

The commit cited in Fixes: did 2 things: it refactored the read-back
polling from sja1105_dynamic_config_read() into a new function,
sja1105_dynamic_config_wait_complete(), and it called that from
sja1105_dynamic_config_write() too.

What is problematic is the refactoring.

The refactored code from sja1105_dynamic_config_poll_valid() works like
the previous one, but the problem is that it uses another packed_buf[]
SPI buffer, and there was code at the end of sja1105_dynamic_config_read()
which was relying on the read-back packed_buf[]:

	/* Don't dereference possibly NULL pointer - maybe caller
	 * only wanted to see whether the entry existed or not.
	 */
	if (entry)
		ops->entry_packing(packed_buf, entry, UNPACK);

After the change, the packed_buf[] that this code sees is no longer the
entry read back from hardware, but the original entry that the caller
passed to the sja1105_dynamic_config_read(), packed into this buffer.

This difference is the most notable with the SJA1105_SEARCH uses from
sja1105pqrs_fdb_add() - used for both fdb and mdb. There, we have logic
added by commit 728db843 ("net: dsa: sja1105: ignore the FDB entry
for unknown multicast when adding a new address") to figure out whether
the address we're trying to add matches on any existing hardware entry,
with the exception of the catch-all multicast address.

That logic was broken, because with sja1105_dynamic_config_read() not
working properly, it doesn't return us the entry read back from
hardware, but the entry that we passed to it. And, since for multicast,
a match will always exist, it will tell us that any mdb entry already
exists at index=0 L2 Address Lookup table. It is index=0 because the
caller doesn't know the index - it wants to find it out, and
sja1105_dynamic_config_read() does:

	if (index < 0) { // SJA1105_SEARCH
		/* Avoid copying a signed negative number to an u64 */
		cmd.index = 0; // <- this
		cmd.search = true;
	} else {
		cmd.index = index;
		cmd.search = false;
	}

So, to the caller of sja1105_dynamic_config_read(), the returned info
looks entirely legit, and it will add all mdb entries to FDB index 0.
There, they will always overwrite each other (not to mention,
potentially they can also overwrite a pre-existing bridge fdb entry),
and the user-visible impact will be that only the last mdb entry will be
forwarded as it should. The others won't (will be flooded or dropped,
depending on the egress flood settings).

Fixing is a bit more complicated, and involves either passing the same
packed_buf[] to sja1105_dynamic_config_wait_complete(), or moving all
the extra processing on the packed_buf[] to
sja1105_dynamic_config_wait_complete(). I've opted for the latter,
because it makes sja1105_dynamic_config_wait_complete() a bit more
self-contained.

Fixes: df405910 ("net: dsa: sja1105: wait for dynamic config command completion on writes too")
Reported-by: Yanan Yang <yanan.yang@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit c9567980 ]

Currently, sja1105_dynamic_config_wait_complete() returns either 0 or
-ETIMEDOUT, because it just looks at the read_poll_timeout() return code.

There will be future changes which move some more checks to
sja1105_dynamic_config_poll_valid(). It is important that we propagate
their exact return code (-ENOENT, -EINVAL), because callers of
sja1105_dynamic_config_read() depend on them.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 7cef293b ("net: dsa: sja1105: fix multicast forwarding working only for last added mdb entry")
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 02c652f5 ]

Commit 4d942354 ("net: dsa: sja1105: offload bridge port flags to
device") has partially hidden some multicast entries from showing up in
the "bridge fdb show" output, but it wasn't enough. Addresses which are
added through "bridge mdb add" still show up. Hide them all.

Fixes: 291d1e72 ("net: dsa: sja1105: Add support for FDB and MDB management")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 32530dba ]

Currently, when a new fdb entry is added (with both ports of the
ADIN2111 bridged), the driver configures the MAC filters for the wrong
port, which results in the forwarding being done by the host, and not
actually hardware offloaded.

The ADIN2111 offloads the forwarding by setting filters on the
destination MAC address of incoming frames. Based on these, they may be
routed to the other port. Thus, if a frame has to be forwarded from port
1 to port 2, the required configuration for the ADDR_FILT_UPRn register
should set the APPLY2PORT1 bit (instead of APPLY2PORT2, as it's
currently the case).

Fixes: bc93e19d ("net: ethernet: adi: Add ADIN1110 support")
Signed-off-by: Ciprian Regus <ciprian.regus@analog.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 54024dbe ]

Use eth_broadcast_addr() to assign broadcast address instead
of memset().

Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 32530dba ("net:ethernet:adi:adin1110: Fix forwarding offload")
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 484b4833 ]

Syzbot reports the following uninit-value access problem.

=====================================================
BUG: KMSAN: uninit-value in fill_frame_info net/hsr/hsr_forward.c:601 [inline]
BUG: KMSAN: uninit-value in hsr_forward_skb+0x9bd/0x30f0 net/hsr/hsr_forward.c:616
 fill_frame_info net/hsr/hsr_forward.c:601 [inline]
 hsr_forward_skb+0x9bd/0x30f0 net/hsr/hsr_forward.c:616
 hsr_dev_xmit+0x192/0x330 net/hsr/hsr_device.c:223
 __netdev_start_xmit include/linux/netdevice.h:4889 [inline]
 netdev_start_xmit include/linux/netdevice.h:4903 [inline]
 xmit_one net/core/dev.c:3544 [inline]
 dev_hard_start_xmit+0x247/0xa10 net/core/dev.c:3560
 __dev_queue_xmit+0x34d0/0x52a0 net/core/dev.c:4340
 dev_queue_xmit include/linux/netdevice.h:3082 [inline]
 packet_xmit+0x9c/0x6b0 net/packet/af_packet.c:276
 packet_snd net/packet/af_packet.c:3087 [inline]
 packet_sendmsg+0x8b1d/0x9f30 net/packet/af_packet.c:3119
 sock_sendmsg_nosec net/socket.c:730 [inline]
 sock_sendmsg net/socket.c:753 [inline]
 __sys_sendto+0x781/0xa30 net/socket.c:2176
 __do_sys_sendto net/socket.c:2188 [inline]
 __se_sys_sendto net/socket.c:2184 [inline]
 __ia32_sys_sendto+0x11f/0x1c0 net/socket.c:2184
 do_syscall_32_irqs_on arch/x86/entry/common.c:112 [inline]
 __do_fast_syscall_32+0xa2/0x100 arch/x86/entry/common.c:178
 do_fast_syscall_32+0x37/0x80 arch/x86/entry/common.c:203
 do_SYSENTER_32+0x1f/0x30 arch/x86/entry/common.c:246
 entry_SYSENTER_compat_after_hwframe+0x70/0x82

Uninit was created at:
 slab_post_alloc_hook+0x12f/0xb70 mm/slab.h:767
 slab_alloc_node mm/slub.c:3478 [inline]
 kmem_cache_alloc_node+0x577/0xa80 mm/slub.c:3523
 kmalloc_reserve+0x148/0x470 net/core/skbuff.c:559
 __alloc_skb+0x318/0x740 net/core/skbuff.c:644
 alloc_skb include/linux/skbuff.h:1286 [inline]
 alloc_skb_with_frags+0xc8/0xbd0 net/core/skbuff.c:6299
 sock_alloc_send_pskb+0xa80/0xbf0 net/core/sock.c:2794
 packet_alloc_skb net/packet/af_packet.c:2936 [inline]
 packet_snd net/packet/af_packet.c:3030 [inline]
 packet_sendmsg+0x70e8/0x9f30 net/packet/af_packet.c:3119
 sock_sendmsg_nosec net/socket.c:730 [inline]
 sock_sendmsg net/socket.c:753 [inline]
 __sys_sendto+0x781/0xa30 net/socket.c:2176
 __do_sys_sendto net/socket.c:2188 [inline]
 __se_sys_sendto net/socket.c:2184 [inline]
 __ia32_sys_sendto+0x11f/0x1c0 net/socket.c:2184
 do_syscall_32_irqs_on arch/x86/entry/common.c:112 [inline]
 __do_fast_syscall_32+0xa2/0x100 arch/x86/entry/common.c:178
 do_fast_syscall_32+0x37/0x80 arch/x86/entry/common.c:203
 do_SYSENTER_32+0x1f/0x30 arch/x86/entry/common.c:246
 entry_SYSENTER_compat_after_hwframe+0x70/0x82

It is because VLAN not yet supported in hsr driver. Return error
when protocol is ETH_P_8021Q in fill_frame_info() now to fix it.

Fixes: 451d8123 ("net: prp: add packet handling support")
Reported-by:  <syzbot+bf7e6250c7ce248f3ec9@syzkaller.appspotmail.com>
Closes: https://syzkaller.appspot.com/bug?extid=bf7e6250c7ce248f3ec9


Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit e4c79810 ]

rule_locs is allocated in ethtool_get_rxnfc and the size is determined by
rule_cnt from user space. So rule_cnt needs to be check before using
rule_locs to avoid NULL pointer dereference.

Fixes: 7aab747e ("net: ethernet: mediatek: add ethtool functions to configure RX flows of HW LRO")
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>