Skip to content
  1. Oct 09, 2013
  3. Oct 08, 2013
  5. Sep 20, 2013
  7. Sep 13, 2013
  9. Sep 07, 2013
  11. Sep 03, 2013
  13. Aug 31, 2013
  15. Aug 30, 2013
  17. Aug 29, 2013
  19. Aug 28, 2013
    • Sebastian Andrzej Siewior's avatar
      usb: musb: am335x: add second port to beagle bone · 2ae847a1
      Sebastian Andrzej Siewior authored 
      

So I assumed that Beagle bone has only one USB port in host mode because
the micro USB connector had an USB-UART there. I was wrong a little. The
second port runs on host mode, but the micro USB plug is connected to an
internal HUB with two ports: one to the USB-UART and one to musb
instance one.
For that reason, this patch enables both ports: the primary in device
mode only and the second in host mode only.

Signed-off-by: default avatarSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: default avatarFelipe Balbi <balbi@ti.com>
      2ae847a1
    • Sebastian Andrzej Siewior's avatar
      usb: musb: am335x-evm: Do not remove the session bit HOST-only mode · 781f1798
      Sebastian Andrzej Siewior authored 
      

This is what I observe:
On the first connect, the musb starts with DEVCTL.Session set. On
disconnect, musb_core calls try_idle. That functions removes the Session
bit signalizing that the session is over (something that only in OTG is
required). A new device, that is plugged, is no longer recognized.
I've setup a timer and checked the DEVCTL register and I haven't seen a
change in VBus and I saw the B-Device bit set. After setting the IDDIG
into A mode and forcing the device to behave like a A device, I didn't
see a change.
Neither VBUS goes to 0b11 nor does a session start request comes.
In the TI-v3.2 kernel they skip to call musb_platform_try_idle() in the
OTG_STATE_A_WAIT_BCON state while not in OTG mode.
Since the second port hast a standard A plug the patch changes the port
to run in host mode only and skips the timer which would remove
DEVCTL.Session so we can reconnect to another device later.

Signed-off-by: default avatarSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: default avatarFelipe Balbi <balbi@ti.com>
      781f1798
    • Sebastian Andrzej Siewior's avatar
      usb: usb: dsps: update code according to the binding document · c031a7d4
      Sebastian Andrzej Siewior authored 
      

This relfects the code and dts requires changes due to recent .dts
binding updates:
- use mg prefix for the Metor Graphics specific attributes
- use power in mA not in mA/2 as specifed in the USB2.0 specification
- remove the child node for USB. This is driver specific on won't be
  reflected in the device tree
- use the "mentor" prefix instead of "mg".
- use "dr_mode" istead of "mg,port-mode" for the port mode. The former
  is used by a few other drivers.

Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: default avatarSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: default avatarFelipe Balbi <balbi@ti.com>
      c031a7d4
    • Sebastian Andrzej Siewior's avatar
      usb: musb: dsps fix the typo in reg-names of the dma node · 3b6394b4
      Sebastian Andrzej Siewior authored 
      

I forgot to separete the different names in the reg-names property. This
didn't cause anything to fail because the driver does not use the names
and simply relies on the order of the memory offsets in reg.
This patch fixes this in case it is used later.

Signed-off-by: default avatarSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: default avatarFelipe Balbi <balbi@ti.com>
      3b6394b4
  21. Aug 27, 2013
  23. Aug 26, 2013
  25. Aug 23, 2013
  27. Aug 22, 2013