The Armada 385 DB board is the development board from Marvell for the
Armada 385 SoC. This commit adds a Device Tree description for this
board, which enables the following features:

 * Network interfaces
 * I2C buses
 * SDIO
 * Serial port
 * SPI bus, with a SPI flash
 * PCIe interfaces

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

The Armada 380 and 385 SoCs are new SoCs from Marvell, based on a
Cortex-A9 cores (single core for 380, dual core for 385) and a number
of hardware blocks that are common with earlier SoCs from the mvebu
family.

The provided Device Tree describes the following parts of the SoC:

 * CPU
 * Device Bus
 * Clocks
 * Interrupt controllers: GIC and MPIC
 * GPIO controllers
 * I2C buses
 * L2 cache
 * MBus controller
 * Pinctrl
 * Serial
 * SPI buses
 * System controller (for reboot)
 * Timer
 * XOR engines
 * PCIe controllers
 * Network interfaces

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

The Armada 375 DB board is the development board from Marvell for the
Armada 375 SoC. This commit adds a Device Tree description for this
board, which enables the following features:

 * I2C buses
 * SDIO
 * Serial port
 * SPI bus, with a SPI flash. Note that the SPI bus is disabled by
   default, because it conflicts with the NAND, and can only work if
   the board boots out of SPI. Since most boards are shipped to boot
   out of NAND, we're default to having the SPI bus disabled.
 * PCIe interfaces

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

The Armada 375 SoC is a new SoC from Marvell, based on a dual core
Cortex-A9 and a number of hardware blocks that are common with earlier
SoCs from the mvebu family.

The provided Device Tree describes the following parts of the SoC:

 * CPUs
 * Device Bus
 * Clocks
 * Interrupt controllers: GIC and MPIC
 * GPIO controllers
 * I2C buses
 * L2 cache
 * MBus controller
 * SDIO
 * Pinctrl
 * SATA
 * Serial
 * SPI buses
 * System controller (for reboot)
 * Timer
 * XOR engines
 * PCIe controllers

Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>

TI_EDMA fell out of automatically selected options in the multi_v7
defconfig due to a select being removed from the davinci Kconfig entry. So
we need to re-enable explicitly to not regress some platforms.

The rest is just the result of running 'make multi_v7_defconfig + make
savedefconfig' to remove entries that are no longer needed due to changed
dependencies/selects or defaults.

Signed-off-by: Olof Johansson <olof@lixom.net>

Recent boot farm testing has highlighted some issues with mvebu and
multiplatform kernels.  Increase the test coverage so we can discover
these issues earlier.

Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Olof Johansson <olof@lixom.net>

The board schematic states that the "SD_CARD_DET_N gets pulled to GND
when card is inserted" so the polarity has been updated to active low.

Polarity is now specified with a GPIO define instead of a magic number.

Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

Select CONFIG_AT803X_PHY so that we can boot hummingboard via NFS.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Drop automatic selection of TI_EDMA from Keystone Kconfig file,
as it produces build warning in case if CONFIG_DMADEVICES is not set:

warning: (ARCH_KEYSTONE) selects TI_EDMA which has unmet direct dependencies (DMADEVICES && (ARCH_DAVINCI || ARCH_OMAP || ARCH_KEYSTONE))

Instead enable TI EDMA support from defconfig.

Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Add nodes for the Arasan SDHCI controller to Zynq dts files.

Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

SMP is a user configurable option, not a hardware feature and should not
be selected.

Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

DEBUG_FS used to be selected by COMMON_CLK_DEBUG, which was enabled
by tegra_defconfig. However, this config option no longer exists, so
no longer selects DEBUG_FS, and nothing else selects it either. So,
"make tegra_defconfig" no longer enables DEBUG_FS in .config.

Rebuild tegra_defconfig on top of next-20140424, while manually
re-enabling DEBUG_FS.

Reasons for removed entries are:
- I2C_MUX: selected by MEDIA_SUBDRV_AUTOSELECT
- DRM_PANEL: selected by DRM_TEGRA
- NEW_LEDS: selected by many things; at least VT
- LEDS_CLASS: selected by many things; at least VT
- LEDS_TRIGGERS: selected by many things; at least VT
- COMMON_CLK_DEBUG: no longer exists

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>

multi_v7_defconfig was missing a large number of options that were in
tegra_defconfig. This patch adds them. The changes fall into the
following categories:

* Enable more Tegra SoC options/drivers.
* Enable more drivers for Tegra boards.
* Enable more options that are useful for running distros.

The patch removes a few lines as well, simply because those options are
now selected by something else, and "make savedefconfig" removes them. I
verified that the options appear in .config after
"make multi_v7_defconfig".

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

This board was missed when converting all the others to proper
abstracted GPIO handling. Fix it up the right way by requesting
and driving GPIO line 0 high through gpiolib to power off the
machine.

Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

Commit 78d16321 deleted the
static mappings of the core modules, but this static map is
still needed on the Integrator/CP (not the Integrator/AP).

Restore the static map on the Integrator/CP.

Reported-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

This allows us to probe the clock controller devices and boot to a
serial console on all DT enabled MSM platforms.

Cc: David Brown <davidb@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

Add the necessary DT nodes to probe the clock controllers on MSM
devices as well as hook up the uart nodes to the clock
controllers. This should allow us to boot to a serial console on
all DT enabled MSM platforms.

Cc: David Brown <davidb@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

Move all OMAP4 PM errata initializations to centralized location in
omap4_pm_init_early. This allows for users to utilize the erratas
in various submodules as needed.

Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

The same workaround as ff999b8a
"ARM: OMAP4460: Workaround for ROM bug because of CA9 r2pX GIC ..."
need to be applied not only when system is booting, but when MPUSS hits
OSWR state through CPUIdle too. Without this WA the same issue is
reproduced now on boards PandaES and Tablet/Blaze with SOM OMAP4460
when CONFIG_CPU_IDLE is enabled.
After MPUSS has enterred OSWR and waken up:
- GIC distributor became disabled forever
- scheduling is not performed any more

Cc: Kevin Hilman <khilman@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reported-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

On ARM, address size can be 32 bits or 64 bits (if CONFIG_ARCH_PHYS_ADDR_T_64BIT
is enabled).
We can't assume that the grant frame base address will always fits in an
unsigned long. Use phys_addr_t instead of unsigned long as argument for
gnttab_setup_auto_xlat_frames.

Signed-off-by: Julien Grall <julien.grall@linaro.org>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>

The use of phys_to_machine and machine_to_phys in the phys<=>bus conversions
causes us to lose the top bits of the DMA address if the size of a DMA address is not the same as the size of the phyiscal address.

This can happen in practice on ARM where foreign pages can be above 4GB even
though the local kernel does not have LPAE page tables enabled (which is
totally reasonable if the guest does not itself have >4GB of RAM). In this
case the kernel still maps the foreign pages at a phys addr below 4G (as it
must) but the resulting DMA address (returned by the grant map operation) is
much higher.

This is analogous to a hardware device which has its view of RAM mapped up
high for some reason.

This patch makes I/O to foreign pages (specifically blkif) work on 32-bit ARM
systems with more than 4GB of RAM.

Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>

Event channels driver needs to be initialized very early. Until now, Xen
initialization was done after all CPUs was bring up.

We can safely move the initialization to an early initcall.

Also use a cpu notifier to:
    - Register the VCPU when the CPU is prepared
    - Enable event channel IRQ when the CPU is running

Signed-off-by: Julien Grall <julien.grall@linaro.org>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>

Add watchdog specific config for kizbox board.

Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

Set default watchdog options in every SoC compatible with the sam9 watchdog.

Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

This change introduces debugfs support for the BCM281xx watchdog driver.

Signed-off-by: Markus Mayer <markus.mayer@linaro.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

This commit adds support for the watchdog timer used on the BCM281xx
family of SoCs.

Signed-off-by: Markus Mayer <markus.mayer@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

GCC fails to build the kernel if EABI is selected, and the default FPU
is selected.  Avoid this by explicitly stating that we want VFP with
EABI.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Commit 65939301 (arm: set initrd_start/initrd_end for fdt scan)
caused the FDT initrd_start and initrd_end to override the
phys_initrd_start and phys_initrd_size set by the initrd= kernel
parameter.  With this patch initrd_start and initrd_end will be
overridden if phys_initrd_start and phys_initrd_size are set by the
kernel initrd= parameter.

Fixes: 65939301 (arm: set initrd_start/initrd_end for fdt scan)

Signed-off-by: Ben Peddell <klightspeed@killerwolves.net>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The pgtbl macro couldn't handle the specific
(TEXT_OFFSET - PG_DIR_SIZE) value that the combination of
MSM platforms and LPAE created:

head.S:163: Error: invalid constant (203000) after fixup

Regardless of whether this combination of configuration options
will work on currently support platforms at run time, make it
at least assemble properly.

Signed-off-by: Christopher Covington <cov@codeaurora.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

__und_usr_thumb function deals with thumb2 opcodes. In case of BE
image, it needs to byteswap half word thumb2 encoded instructions
before further processing them.

Without this fix BE image user-land thread executing first VFP
instruction encoded in thumb2 fails with SIGILL, because kernel
does not recognize instruction and does not enable VFP.

Reported-by: Corey Melton <comelton@cisco.com>
Signed-off-by: Victor Kamensky <victor.kamensky@linaro.org>
Tested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Some SoC have MMIO regions that are shared across orthogonal
subsystems. This commit implements a possible solution for the
thread-safe access of such regions through a spinlock-protected API.

Concurrent access is protected with a single spinlock for the
entire MMIO address space. While this protects shared-registers,
it also serializes access to unrelated/unshared registers.

We add relaxed and non-relaxed variants, by using writel_relaxed and writel,
respectively. The rationale for this is that some users may not require
register write completion but only thread-safe access to a register.

Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

The new memblock_virt APIs are used to replaced old bootmem API.

We need to allocate page below 4G for swiotlb.

That should fix regression on Andrew's system that is using swiotlb.

Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

LED platform data are overwhelmed by excessive field "max_cur"
which just replicates few bits of "led_control" field.
This patch removes this field and adds a definition for the
current settings in the header.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Bryan Wu <cooloney@gmail.com>

Add support for the SolidRun Cubox-i devices.  This commit adds similar
basic support as the HummingBoard.  Further devices will be supported
in future patches.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

Add support for the SolidRun HummingBoard.  This commit adds support for
the following interfaces on this board:

- Consumer Ir receiver
- S/PDIF output
- Both USB interfaces
- Gigabit Ethernet using AR8035
- UART port

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

When a skeleton "clocks { .. }" remain in .dtsi, the child node can
be moved to .dts, "ref12" is then found by of_clk_get().

Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Remove an outdated reference to "most personal computers" having only one
CPU, and change the use of "singleprocessor" and "single processor" in
CONFIG_SMP's documentation to "uniprocessor" across all arches where that
documentation is present.

Signed-off-by: Robert Graffham <psquid@psquid.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

plat/regs-nand.h is used only by S3C2410 nand driver. Since there
are no other users, merge this file into the driver code to remove
platform dependency. While at it also remove unused macros.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Switch to memblock interfaces for early memory allocator instead of
bootmem allocator.  No functional change in beahvior than what it is in
current code from bootmem users points of view.

Archs already converted to NO_BOOTMEM now directly use memblock
interfaces instead of bootmem wrappers build on top of memblock.  And
the archs which still uses bootmem, these new apis just fallback to
exiting bootmem APIs.

Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tejun Heo <tj@kernel.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Yinghai Lu <yinghai@kernel.org>

Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Switch to memblock interfaces for early memory allocator instead of
bootmem allocator.  No functional change in beahvior than what it is in
current code from bootmem users points of view.

Archs already converted to NO_BOOTMEM now directly use memblock
interfaces instead of bootmem wrappers build on top of memblock.  And
the archs which still uses bootmem, these new apis just fallback to
exiting bootmem APIs.

Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tejun Heo <tj@kernel.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Yinghai Lu <yinghai@kernel.org>

Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>