Add a minimum Device Tree for Acme Arietta G25.
http://acme.systems/arietta



Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Sergio Tanzilli <tanzilli@acmesystems.it>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Use stdout-path to specify the console and remove the console argument from
the kernel command line.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Use stdout-path to specify the console and remove the console argument from
the kernel command line.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Use stdout-path to specify the console and remove the bootargs.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Use stdout-path to specify the console and remove the console argument from
the kernel command line.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Use stdout-path to specify the console and remove the console argument from
the kernel command line.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Use stdout-path to specify the console and remove the console argument from
the kernel command line.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Use stdout-path to specify the console and remove the console argument from
the kernel command line.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Use stdout-path to specify the console and remove the console argument from
the kernel command line.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Use stdout-path to specify the console and remove the console argument from
the kernel command line.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Use stdout-path to specify the console and remove the console argument from
the kernel command line.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Use stdout-path to specify the console and remove the console argument from
the kernel command line.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Use stdout-path to specify the console.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

The kizbox dts are using the deprecated linux,stdout-path. Replace those by
stdout-path.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Gaël PORTAY <g.portay@overkiz.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Add RTC support to the at91sam9rlek.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

The RTC lives at 0xfffffe00. Also reorder the node properly.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

The ohci driver now calls clk_set_rate on the uhpck clock (which forwards
set_rate requests to its parent: the usb clock).
Remove useless references to usb clocks from ohci definitions.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

The uhpck is useless for High-Speed communications, remove the reference
to this clock in all ehci definitions.

Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

SCK1 pin is pioC 29. Comment was okay.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Add vcc_mmc1 fixed regulator to remove the 'no vmmc regulator found' warning
when probing the mmc1 device.

Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Add fixed regulator for vmmc0 and attach the vmmc for it to the mmc0
node on the SAM5D3 Xplained board. This will remove the following
warning from the kernel:

atmel_mci f0000000.mmc: No vmmc regulator found

Note, atmel_defconfig will need fixed regulator support enabled if this
is to be used properly.

Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
[use a fixed regulator instead of gpio one]
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

The SAM5D3 Xplained device tree is missing the vqmmc node which is
tied to 3.3V on the board. Add this to avoid the kernel warning that
there is no vqmmc node.

atmel_mci f0000000.mmc: No vqmmc regulator found

Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

The mmc1 channel is not populated on the SAM5D3 Xplained board, however
it is enabled and therefore the driver is attaching to it.

The node configuration for mmc1 is missing, so add an mmc1 node in the
device tree and set its status to disabled. Also add the vmmc and the
necessary slot configuration if this node were enabled to avoid the following
warnings from the driver:

atmel_mci f8000000.mmc: No vmmc regulator found
atmel_mci f8000000.mmc: No vqmmc regulator found

Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

commit 111573cc

 ("mtd: atmel_nand: check NFC busy flag by HSMC_SR
instead of NFC cmd regs")
check NFC busy by nfc SR instead of NFC cmd regs. So we don't need to
map NFC cmd registers to include NFCBUSY bit.
That means we only need map 0x08000000 instead of 0x10000000 for NFC
cmd regs.

This patch reduce the NFC cmd regs map for sama5d3 & sama5d4.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Update the pinctrl ranges property to support pioD controller whose
mapping is not contiguous with other pio controllers. Without this
update, getting resource will fail, then pinctrl probe will fail too
because there is a missing pio controller.

Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Specify the phy address on macb0 node aka GEM.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Route SPI1 on the Arduino "in the middle" spi connector.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Add sama5d4 spi1, spi2 dt nodes & pinctrl.

Signed-off-by: Suchang Ko <suchangko@samul.kr>
[nicolas.ferre@atmel.com: split patch, reorder & whitespace fixes]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Add sama5d4 uart0, uart1 dt nodes, pinctrl and related aliases.

Signed-off-by: Suchang Ko <suchangko@samul.kr>
[nicolas.ferre@atmel.com: split patch, reorder & whitespace fixes]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Also add the pinctrl for usart0, usart1.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

The clock-frequency property became obsolete since the rework of the main
clock driver in 3.16 (see commit 27cb1c20

).

It now get and uses the clock-frequency from the main_xtal node.

Signed-off-by: Gaël PORTAY <g.portay@overkiz.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Add DT file for Kizbox 2 board.
This board is based on Atmel's SAMA5D31 Cortex-A5 SoC.

Signed-off-by: Gaël PORTAY <g.portay@overkiz.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Add DT file for Kizbox mini board.
This board is based on Atmel's AT91SAM9G25 SoC.

Signed-off-by: Gaël PORTAY <g.portay@overkiz.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Defines the pinctrl configurations for PWM0.

Signed-off-by: Gaël PORTAY <g.portay@overkiz.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Simplify the bootargs since the platform is booting from an initramfs and
set the kernel stdout path to DBGU.

Signed-off-by: Gaël PORTAY <g.portay@overkiz.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Re-size NAND partitions since the bootstrap is able to read volumes from an
UBI image.

Signed-off-by: Gaël PORTAY <g.portay@overkiz.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

This:
 * moves to pwm-leds using tcb-pwm driver and
 * renames leds to pwm:<color>:<function>.

Signed-off-by: Gaël PORTAY <g.portay@overkiz.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

This:
 * fixes active level of GPIO (active high) and
 * renames buttons:
   - reset (PB_RST), and
   - mode to user (PB_USER).

Signed-off-by: Gaël PORTAY <g.portay@overkiz.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

USART3 is the only serial UART accessible.

Signed-off-by: Gaël PORTAY <g.portay@overkiz.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>

Consists in:
 * sorting nodes by address as possible or alphabetically,
 * adding myself as new maintainer and
 * update license.

Signed-off-by: Gaël PORTAY <g.portay@overkiz.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>